A large quantity of industrial hazardous wastes (IHWs) accumulates in the Three Gorges Region. This study found that approximately 15 000 t IHWs were piled in the region by October 2001. These IHWs came from various s...A large quantity of industrial hazardous wastes (IHWs) accumulates in the Three Gorges Region. This study found that approximately 15 000 t IHWs were piled in the region by October 2001. These IHWs came from various sources and were complex in composition, mostly toxic and difficult to be disposed. IHW is regarded as a potential threat to the ecological environment, water resources and survival of local residents. It is important and indispensable to dispose the waste properly. To meet the regulation requirements on the disposal of IHWs and to minimize environmental effects on the Three Gorges Region, a disposal strategy is proposed, according to which approximately 600 t of the IHWs can be disposed by chemical stabilization, incineration and other treatment measures, and the rest need be stockpiled in safe and reliable places situated above the 177 m impoundment line of the Three Gorges dam.展开更多
"Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China..."Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China and the high cost of CO_(2)capture,CO_(2)-rich industrial waste gas(CO_(2)-rich IWG)is gradually emerging into the public's gaze.CO_(2)has good adsorption properties on shale surfaces,but acidic gases can react with shale,so the mechanism of the CO_(2)-rich IWG-water-shale reaction and the change in reservoir properties will determine the stability of geological storage.Therefore,based on the mineral composition of the Longmaxi Formation shale,this study constructs a thermodynamic equilibrium model of water-rock reactions and simulates the regularity of reactions between CO_(2)-rich IWG and shale minerals.The results indicate that CO_(2)consumed 12%after reaction,and impurity gases in the CO_(2)-rich IWG can be dissolved entirely,thus demonstrating the feasibility of treating IWG through water-rock reactions.Since IWG inhibits the dissolution of CO_(2),the optimal composition of CO_(2)-rich IWG is 95%CO_(2)and 5%IWG when CO_(2)geological storage is the main goal.In contrast,when the main goal is the geological storage of total CO_(2)-rich IWG or impurity gas,the optimal CO_(2)-rich IWG composition is 50%CO_(2)and 50%IWG.In the CO_(2)-rich IWG-water-shale reaction,temperature has less influence on the water-rock reaction,while pressure is the most important parameter.SO2 has the greatest impact on water-rock reaction in gas.For minerals,clay minerals such as illite and montmorillonite had a significant effect on water-rock reaction.The overall reaction is dominated by precipitation and the volume of the rock skeleton has increased by 0.74 cm3,resulting in a decrease in shale porosity,which enhances the stability of CO_(2)geological storage to some extent.During the reaction between CO_(2)-rich IWG-water-shale at simulated temperatures and pressures,precipitation is the main reaction,and shale porosity decreases.However,as the reservoir water content increases,the reaction will first dissolve and then precipitate before dissolving again.When the water content is less than 0.0005 kg or greater than 0.4 kg,it will lead to an increase in reservoir porosity,which ultimately reduces the long-term geological storage stability of CO_(2)-rich IWG.展开更多
The biodegradation of polymeric biocomposites formed from epoxidized linseed oil and various types of fillers(pine needles,pine bark,grain mill waste,rapeseed cake)and a control sample without filler was studied durin...The biodegradation of polymeric biocomposites formed from epoxidized linseed oil and various types of fillers(pine needles,pine bark,grain mill waste,rapeseed cake)and a control sample without filler was studied during 180 days of exposure to two types of forest soil:deciduous and coniferous.The weight loss,morphological,and structural changes of polymer composites were noticed after 180 days of the soil burial test.The greatest weight loss of all tested samples was observed in coniferous forest soil(41.8%–63.2%),while in deciduous forest soil,it ranged between 37.7%and 42.3%.The most significant changes in the intensities of the signals evaluated by attenuated total reflectance infrared spectroscopy,as well as morphological changes determined by scanning electron microscopy,were assessed for polymer composite with rapeseed cake and specimen without filler in coniferous forest soil and are in a good agreement with weight loss results.Whereas significantly lower changes in weight loss,morphology,and structure of polymeric film with pine bark were noticed in both soils.It was suggested that fungi of Trichoderma,Penicillium,Talaromyces and Clonostachys genera are the possible soil microorganisms that degrade linseed oil-based cross-linked polymer composites.Moreover,the novel polymer composites have the potential to be an environmentally friendly alternative to petroleum-based mulching films.展开更多
Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was c...Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.展开更多
Proper waste management models using recent technologies like computer vision,machine learning(ML),and deep learning(DL)are needed to effectively handle the massive quantity of increasing waste.Therefore,waste classif...Proper waste management models using recent technologies like computer vision,machine learning(ML),and deep learning(DL)are needed to effectively handle the massive quantity of increasing waste.Therefore,waste classification becomes a crucial topic which helps to categorize waste into hazardous or non-hazardous ones and thereby assist in the decision making of the waste management process.This study concentrates on the design of hazardous waste detection and classification using ensemble learning(HWDC-EL)technique to reduce toxicity and improve human health.The goal of the HWDC-EL technique is to detect the multiple classes of wastes,particularly hazardous and non-hazardous wastes.The HWDC-EL technique involves the ensemble of three feature extractors using Model Averaging technique namely discrete local binary patterns(DLBP),EfficientNet,and DenseNet121.In addition,the flower pollination algorithm(FPA)based hyperparameter optimizers are used to optimally adjust the parameters involved in the EfficientNet and DenseNet121 models.Moreover,a weighted voting-based ensemble classifier is derived using three machine learning algorithms namely support vector machine(SVM),extreme learning machine(ELM),and gradient boosting tree(GBT).The performance of the HWDC-EL technique is tested using a benchmark Garbage dataset and it obtains a maximum accuracy of 98.85%.展开更多
The hazardous waste produced by coal-fired power plants are large in quantity and variety. It is important for ecological environment protection to properly store hazardous waste in coal-fired power plants. The enviro...The hazardous waste produced by coal-fired power plants are large in quantity and variety. It is important for ecological environment protection to properly store hazardous waste in coal-fired power plants. The environmental management of hazardous waste in coal-fired power plants started late, and there are many problems in the construction and management of their storage facilities. In this paper, taking eight typical coal-fired power plants as examples, the present problems of hazardous waste storage facilities in coal-fired power plants are analyzed, and corresponding countermeasures are put forward to solve the main common problems.展开更多
Porous materials have promise as sound insulation, heat barrier, vibration attenuation, and catalysts. Most industrial solid wastes, such as tailings, coal gangue, and fly ash are rich in silicon. Additionally, a high...Porous materials have promise as sound insulation, heat barrier, vibration attenuation, and catalysts. Most industrial solid wastes, such as tailings, coal gangue, and fly ash are rich in silicon. Additionally, a high silicon content waste is a potential raw material for the syn- thesis of silicon-based, multi-porous materials such as zeolites, mesoporous silica, glass-ceramics, and geopolymer foams. Representative sil- icon-rich industrial solid wastes (SRISWs) are the focus of this mini review of the processing and application of porous silicon materials with respect to the physical and chemical properties of the SRISW. The transformation methods of preparing porous materials from SRISWs are summarized, and their research status in micro-, meso-, and macro-scale porous materials are described. Possible problems in the application of SRISWs and in the preparation of functional porous materials are analyzed, and their development prospects are discussed. This review should provide a typical reference for the recycling and use of industrial solid wastes to develop sustainable “green materials.”展开更多
The catalytic effects of four industrial wastes,namely,the soap residue(SR),brine sludge(BS),calcium carbide residue(CCR),and white lime mud(WLM),on coal thermal ignition were investigated.The acidity of palmitate ani...The catalytic effects of four industrial wastes,namely,the soap residue(SR),brine sludge(BS),calcium carbide residue(CCR),and white lime mud(WLM),on coal thermal ignition were investigated.The acidity of palmitate anion associated with Na+in SR was lower than that of chloride anion combined with Na+in BS,which resulted in an improved the combustion of SR.The acidity of OH-anion combined with Ca2+in CCR was lower than that of CO32-anion combined with Ca2+in WLM,resulting in CCR exhibiting a better catalytic effect on coal ignition.The alkaline metal Na had lower initial ionisation energy than the alkaline earth metal Ca.Therefore,the Na-rich SR exhibited higher catalytic activity on coal ignition than Ca-rich CCR.The ignition temperature of coal with 0.5%SR decreased from 544 to 503°C.展开更多
The situation of porous ceramics prepared from industrial waste slag(fly ash,red mud,metallurgical slag,tailings,etc.)was summarized.It was pointed out that the preparation of porous ceramics from industrial waste sla...The situation of porous ceramics prepared from industrial waste slag(fly ash,red mud,metallurgical slag,tailings,etc.)was summarized.It was pointed out that the preparation of porous ceramics from industrial waste slag can bring long-term economic and social benefits.The development trend of secondary utilization of industrial waste slag was also prospected.展开更多
The effects of the grinding mode,fineness,gypsum kinds and dosage,mix proportions on properties of the composite cements consisting of slag,fly ash,limestone and a lower content clinker were investigated,respectively....The effects of the grinding mode,fineness,gypsum kinds and dosage,mix proportions on properties of the composite cements consisting of slag,fly ash,limestone and a lower content clinker were investigated,respectively.The results show that when the proportions among slag,fly ash and limestone are appropriate,the grinding technology and system are reasonable,the optimized gypsums and additives are effective,the 52.5R grade cement (52.5R grade cement means a higher strength than 52.5 at early age) can be prepared by clinker dosage of 50% in weight,the 42.5R or 42.5,32.5 grade composite cement containing 40% and 30% clinker also may be made, respectively.Moreover,the high performance concrete prepared from the above composite cements was studied experimentally.展开更多
The performance of industrial waste incineration bottom ash in controlled low-strength material (CLSM) was investigated in this paper, as the quarry dust was added. CLSM mixtures were made from the industrial waste in...The performance of industrial waste incineration bottom ash in controlled low-strength material (CLSM) was investigated in this paper, as the quarry dust was added. CLSM mixtures were made from the industrial waste incineration bottom ash, quarry dust, and cement. Tests for fresh density, bleeding, compressive strength, shear strength, hydraulic conductivity, and excavatability were carried out. The com-pressive strength ranges from 60 kPa to 6790 kPa, the friction angle varies from 5° to 19°, and the cohesion is from 4 to 604 kPa. Most of the mixtures are found to be non-excavatable. It is indicated that the quarry dust addition increases the compressive strength and shear parame-ters, decreases bleeding, and increases the removability modulus.展开更多
M, a particular industrial waste, was selected to detoxify chromium slag at a high temperature. The carbon remaining in M reduced Cr （Ⅵ） of Na2CrO4 borne in the chromium slag to Cr （Ⅲ） in the solid phase reactio...M, a particular industrial waste, was selected to detoxify chromium slag at a high temperature. The carbon remaining in M reduced Cr （Ⅵ） of Na2CrO4 borne in the chromium slag to Cr （Ⅲ） in the solid phase reaction, and its thermodynamics and kinetics were studied. The reduction process of Na2CrO4 by carbon produced CO, which was endothermic. Under the experimental condition, the apparent activation energy was 4.41 kJ·mol -1 , the apparent order of reaction for Na2CrO4 was equal to one, and the partial pressure of CO was only 0.22 Pa at 1 330 ℃.展开更多
Destruction of industrial waste in cement rotary kilins(CRKs) is an alternative technology for the treatment of certain types of industrial waste(IW).In this paper,three typical types of industrial wastes were co-inci...Destruction of industrial waste in cement rotary kilins(CRKs) is an alternative technology for the treatment of certain types of industrial waste(IW).In this paper,three typical types of industrial wastes were co-incinerated in the CRK at Beijing Cement Plant to determine the effects of waste disposal(especially solid waste disposal )on the quality of clinker and the concentration of pollutants in air emission.Experimental results show that(1) waste disposal does not affect the quality of clinker and fly ash,and fly ash after the IW disposal can still be used in the cement production,(2) heavy metals from IW are immobilized and stabilized in the clinker and cement,and (3) concentration of pollutants in air emission is far below than the permitted values in the China National Standard-Air Pollutants Emission Standard(GB 16297-1996).展开更多
This paper deals briefly with the pollution caused by hazardous wastes in China, the hazardous waste management at present and the strategy that should be taken for hazardous waste management in the future. Hazardous ...This paper deals briefly with the pollution caused by hazardous wastes in China, the hazardous waste management at present and the strategy that should be taken for hazardous waste management in the future. Hazardous waste problem has become one of the important environmental concerns in China. Hazardous waste have resulted in ecological and environmental destruction, caused damage to human health, and restricted economic development. Although a great effort has been devoted to the management of hazardous wastes, there remain many issues in legislation, experience, technology and finance to be solved. Some recommendations are made on the strategic measures for improving the hazardous waste management in China, particularly relating to legislation, technical development and international cooperation.展开更多
This article describes the investigation of hazardous waste (HW) in the Three Gorges Area of Chongqing region, which indicates that by May 2002, the dumped HW therein amounted to 14 600 t and was mainly distributed in...This article describes the investigation of hazardous waste (HW) in the Three Gorges Area of Chongqing region, which indicates that by May 2002, the dumped HW therein amounted to 14 600 t and was mainly distributed in five districts and counties with 11 000 t in Fuling, 1 650 t in Fengdu, 950 t in Wanzhou; 630 t in Wushan and 430 t in Yunyang. The total amount was composed of 9 670 t chromic residue, 2 310 t waste oil and residue, 410 t waste (false) fertilizer, 28 t waste chemical medicine, 26 t waste materials and 2 200 t other things including acid residue, waste asbestos, fluorine silicate, pigment, additive, waste acid, alkali, nitric acid, vitriol, lead mud, storage battery, calcium carbide, potassium cyanide, polluted soil, discard dynamite, waste packing barrel of cyanides, etc. In all of the HW, 578 t can be treated by chemical neutralization and stabilization technology such as redox, chemical precipitation, acid and alkali neutralization, etc., and the rest is temporarily untreatble and should be removed and piled at a temporary storage site above the 177 m water level of the dam with an aim to be transported to a future disposal site for innocuous treatment.展开更多
[Objective] This paper aimed to study the rapid identification method of hazardous wastes from illegal oil refining,and provide a new theoretical basis and practical basis for shortening the appraisal cycle and reduci...[Objective] This paper aimed to study the rapid identification method of hazardous wastes from illegal oil refining,and provide a new theoretical basis and practical basis for shortening the appraisal cycle and reducing the cost of identification.[Method] The identified substance and the qualified oil products were diluted by carbon disulfide with a ratio of 1∶100 for the gas chromatographic analysis.According to the corresponding national standard,the oil change indexes,such as the moisture content,viscosity,acid value and mechanical impurities of the identified substance,were measured.[Result] By the comparison between the gas chromatogram spectrograms of the identified substance and the qualified oil,it is found that the main component of the identified substance was the mineral oils.And the test results of oil change index showed that the mineral oil was unqualified.[Conclusion] This method was of great significance to save the cost of appraisal and improve the efficiency of case handling.展开更多
As industrialization accelerates and the amount of hazardous waste generated gradually increases,the means of disposal of hazardous waste is of increasing concern.In this paper,a 40 t/d counter-fow rotary kiln inciner...As industrialization accelerates and the amount of hazardous waste generated gradually increases,the means of disposal of hazardous waste is of increasing concern.In this paper,a 40 t/d counter-fow rotary kiln incineration system owned by a Jiangsu environmental protection company was researched.The software Aspen Plus was used to build the mixed pyrolysis model and the software Fluent was used to build the computational fuid dynamics model of the incineration system.The infuence of the calorifc value of the hazardous waste,the operating temperature and the air supply on the operational efectiveness of the incineration system were analyzed by varying the simulation conditions.The results show that the SO_(x)and NO_(x)content of the product is lower when the operating temperature is above 800℃.The incineration system could only operate above 800℃when the calorifc value of the hazardous waste is not less than 1500 kcal/kg.The incineration system operated best at a primary air velocity of 1.5 m/s.The simulation results in this paper serve as a guide for the operation of counter-fow rotary kiln incineration systems.展开更多
Nowadays, with regard to environmental issues, proper operation of wastewater treatment plants is of particular importance that in the case of inappropriate utilization, they will cause serious problems. Processes tha...Nowadays, with regard to environmental issues, proper operation of wastewater treatment plants is of particular importance that in the case of inappropriate utilization, they will cause serious problems. Processes that exist in environmental systems and environmental engineers are dealing with them mostly have two major characteristics: they are dependent on many variables;and there are complex relationships between its components which make them very difficult to analyze. Being familiar with characteristics of industrial town effluents from various wastewater treatment units, which have high qualitative and quantitative variations and more uncertainties compared to urban wastewaters, plays very effective role in governing them. In order to achieve a better and efficient control over the operation of an industrial wastewater treatment plant, powerful mathematical tool can be used that is based on recorded data from some basic parameters of wastewater during a period of treatment plant operation. In this study, the multilayer perceptron (MLP) feed forward neural network with a hidden layer and stop training method was used to predict quality parameters of the industrial effluent. Data of this study are related to the Fajr Industrial Wastewater Treatment Plant located in Mahshahr—Iran that qualitative and quantitative characteristics of its units were used for training, calibration and evaluation of the neural model. Also, Principal Component Analysis technique was applied to modify and improve performance of generated models of neural networks. The results of this model showed good accuracy of the model in estimating qualitative pro- file of wastewater. This model facilitates evaluating the performance of each treatment plant units through comparing the results of prediction model with the standard amount of output.展开更多
Zeolite synthesis was studied using two silica rich filtration residues (FR 1 and FR 2) as Si-source and sodium aluminate in a direct synthesis at 60°C at strong alkaline conditions (8 M - 16 M NaOH). In addition...Zeolite synthesis was studied using two silica rich filtration residues (FR 1 and FR 2) as Si-source and sodium aluminate in a direct synthesis at 60°C at strong alkaline conditions (8 M - 16 M NaOH). In addition to these one-pot syntheses, a two-step process was investigated. Here, an alkaline digestion of FR at 60°C was followed by gel precipitation with sodium aluminate and gel crystallization under usual conditions of 80°C - 90°C. The results show that the substitution of chemical reagent sodium silicate by a waste material like FR as Si-source is possible but requires fine tuning of the reaction conditions as zeolite crystallization is a process under kinetic control. The solubility behaviour and impurities of the inserted filtration residues strongly influenced the course of reaction. Thus zeolites like hydrosodalite or intermediate zeolite between cancrinite and sodalite, or zeolite NaA or Z-21 in cocrystallization with hydrosodalite could be observed in the one pot syntheses already in a short time interval between 1 - 4 h depending on the alkalinity. The two step process yield to zeolites NaA and NaX in very good quality. The reaction process of FR in both reaction methods was characterized by chemical analyses, X-ray powder diffraction, Fourier transform infrared spectroscopy as well as scanning electron microscopy. Surface area and water content of selected products were further characterized by the BET-method and by thermogravimetry. Summing up the results, we can show that zeolite formation from filtration residues is possible by several reaction procedures as model cases for a re-use of industrial waste materials. Beside the importance for environmental protection, the reactions are of interest for zeolite chemistry as the re-use of FR is possible under economically conditions of low energy consumption at 60°C and short reaction periods.展开更多
文摘A large quantity of industrial hazardous wastes (IHWs) accumulates in the Three Gorges Region. This study found that approximately 15 000 t IHWs were piled in the region by October 2001. These IHWs came from various sources and were complex in composition, mostly toxic and difficult to be disposed. IHW is regarded as a potential threat to the ecological environment, water resources and survival of local residents. It is important and indispensable to dispose the waste properly. To meet the regulation requirements on the disposal of IHWs and to minimize environmental effects on the Three Gorges Region, a disposal strategy is proposed, according to which approximately 600 t of the IHWs can be disposed by chemical stabilization, incineration and other treatment measures, and the rest need be stockpiled in safe and reliable places situated above the 177 m impoundment line of the Three Gorges dam.
基金The work was supported by the National Natural Science Foundation of China(No.52074316)PetroChina Company Limited(No.2019E-2608).
文摘"Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China and the high cost of CO_(2)capture,CO_(2)-rich industrial waste gas(CO_(2)-rich IWG)is gradually emerging into the public's gaze.CO_(2)has good adsorption properties on shale surfaces,but acidic gases can react with shale,so the mechanism of the CO_(2)-rich IWG-water-shale reaction and the change in reservoir properties will determine the stability of geological storage.Therefore,based on the mineral composition of the Longmaxi Formation shale,this study constructs a thermodynamic equilibrium model of water-rock reactions and simulates the regularity of reactions between CO_(2)-rich IWG and shale minerals.The results indicate that CO_(2)consumed 12%after reaction,and impurity gases in the CO_(2)-rich IWG can be dissolved entirely,thus demonstrating the feasibility of treating IWG through water-rock reactions.Since IWG inhibits the dissolution of CO_(2),the optimal composition of CO_(2)-rich IWG is 95%CO_(2)and 5%IWG when CO_(2)geological storage is the main goal.In contrast,when the main goal is the geological storage of total CO_(2)-rich IWG or impurity gas,the optimal CO_(2)-rich IWG composition is 50%CO_(2)and 50%IWG.In the CO_(2)-rich IWG-water-shale reaction,temperature has less influence on the water-rock reaction,while pressure is the most important parameter.SO2 has the greatest impact on water-rock reaction in gas.For minerals,clay minerals such as illite and montmorillonite had a significant effect on water-rock reaction.The overall reaction is dominated by precipitation and the volume of the rock skeleton has increased by 0.74 cm3,resulting in a decrease in shale porosity,which enhances the stability of CO_(2)geological storage to some extent.During the reaction between CO_(2)-rich IWG-water-shale at simulated temperatures and pressures,precipitation is the main reaction,and shale porosity decreases.However,as the reservoir water content increases,the reaction will first dissolve and then precipitate before dissolving again.When the water content is less than 0.0005 kg or greater than 0.4 kg,it will lead to an increase in reservoir porosity,which ultimately reduces the long-term geological storage stability of CO_(2)-rich IWG.
文摘The biodegradation of polymeric biocomposites formed from epoxidized linseed oil and various types of fillers(pine needles,pine bark,grain mill waste,rapeseed cake)and a control sample without filler was studied during 180 days of exposure to two types of forest soil:deciduous and coniferous.The weight loss,morphological,and structural changes of polymer composites were noticed after 180 days of the soil burial test.The greatest weight loss of all tested samples was observed in coniferous forest soil(41.8%–63.2%),while in deciduous forest soil,it ranged between 37.7%and 42.3%.The most significant changes in the intensities of the signals evaluated by attenuated total reflectance infrared spectroscopy,as well as morphological changes determined by scanning electron microscopy,were assessed for polymer composite with rapeseed cake and specimen without filler in coniferous forest soil and are in a good agreement with weight loss results.Whereas significantly lower changes in weight loss,morphology,and structure of polymeric film with pine bark were noticed in both soils.It was suggested that fungi of Trichoderma,Penicillium,Talaromyces and Clonostachys genera are the possible soil microorganisms that degrade linseed oil-based cross-linked polymer composites.Moreover,the novel polymer composites have the potential to be an environmentally friendly alternative to petroleum-based mulching films.
基金financially supported by the National Natural Science Foundation of China(No.51972019)the National Key Research and Development Program of China(No.2019YFC1905702)。
文摘Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.
基金the Deanship of Scientific Research at King Khalid University for funding this work underGrant Number(RGP 2/209/42)PrincessNourah bint Abdulrahman University Researchers Supporting Project Number(PNURSP2022R136)Princess Nourah bint Abdulrahman University,Riyadh,Saudi Arabia.The authors would like to thank the Deanship of Scientific Research at Umm Al-Qura University for supporting this work by Grant Code:(22UQU4210118DSR27).
文摘Proper waste management models using recent technologies like computer vision,machine learning(ML),and deep learning(DL)are needed to effectively handle the massive quantity of increasing waste.Therefore,waste classification becomes a crucial topic which helps to categorize waste into hazardous or non-hazardous ones and thereby assist in the decision making of the waste management process.This study concentrates on the design of hazardous waste detection and classification using ensemble learning(HWDC-EL)technique to reduce toxicity and improve human health.The goal of the HWDC-EL technique is to detect the multiple classes of wastes,particularly hazardous and non-hazardous wastes.The HWDC-EL technique involves the ensemble of three feature extractors using Model Averaging technique namely discrete local binary patterns(DLBP),EfficientNet,and DenseNet121.In addition,the flower pollination algorithm(FPA)based hyperparameter optimizers are used to optimally adjust the parameters involved in the EfficientNet and DenseNet121 models.Moreover,a weighted voting-based ensemble classifier is derived using three machine learning algorithms namely support vector machine(SVM),extreme learning machine(ELM),and gradient boosting tree(GBT).The performance of the HWDC-EL technique is tested using a benchmark Garbage dataset and it obtains a maximum accuracy of 98.85%.
文摘The hazardous waste produced by coal-fired power plants are large in quantity and variety. It is important for ecological environment protection to properly store hazardous waste in coal-fired power plants. The environmental management of hazardous waste in coal-fired power plants started late, and there are many problems in the construction and management of their storage facilities. In this paper, taking eight typical coal-fired power plants as examples, the present problems of hazardous waste storage facilities in coal-fired power plants are analyzed, and corresponding countermeasures are put forward to solve the main common problems.
基金National Natural Science Foundation of China(No.51774331)Funds for Nationsl&Local Joint Engineering Research Center of Mineral Salt Deep Utilization(No.SF202103).
文摘Porous materials have promise as sound insulation, heat barrier, vibration attenuation, and catalysts. Most industrial solid wastes, such as tailings, coal gangue, and fly ash are rich in silicon. Additionally, a high silicon content waste is a potential raw material for the syn- thesis of silicon-based, multi-porous materials such as zeolites, mesoporous silica, glass-ceramics, and geopolymer foams. Representative sil- icon-rich industrial solid wastes (SRISWs) are the focus of this mini review of the processing and application of porous silicon materials with respect to the physical and chemical properties of the SRISW. The transformation methods of preparing porous materials from SRISWs are summarized, and their research status in micro-, meso-, and macro-scale porous materials are described. Possible problems in the application of SRISWs and in the preparation of functional porous materials are analyzed, and their development prospects are discussed. This review should provide a typical reference for the recycling and use of industrial solid wastes to develop sustainable “green materials.”
基金Supported by the National Key Research and Development Program of China(2016YFB0600505)the National Natural Science Foundation of China(51676171).
文摘The catalytic effects of four industrial wastes,namely,the soap residue(SR),brine sludge(BS),calcium carbide residue(CCR),and white lime mud(WLM),on coal thermal ignition were investigated.The acidity of palmitate anion associated with Na+in SR was lower than that of chloride anion combined with Na+in BS,which resulted in an improved the combustion of SR.The acidity of OH-anion combined with Ca2+in CCR was lower than that of CO32-anion combined with Ca2+in WLM,resulting in CCR exhibiting a better catalytic effect on coal ignition.The alkaline metal Na had lower initial ionisation energy than the alkaline earth metal Ca.Therefore,the Na-rich SR exhibited higher catalytic activity on coal ignition than Ca-rich CCR.The ignition temperature of coal with 0.5%SR decreased from 544 to 503°C.
基金financially supported by the open research fund for the State Key Laboratory of Advanced Refractories (Grant No. SKLAR201904)Fundamental Research Fund for the Central Universities (Grant No. N150204021)National Natural Science Foundation of China (Grant No. 51772277)
文摘The situation of porous ceramics prepared from industrial waste slag(fly ash,red mud,metallurgical slag,tailings,etc.)was summarized.It was pointed out that the preparation of porous ceramics from industrial waste slag can bring long-term economic and social benefits.The development trend of secondary utilization of industrial waste slag was also prospected.
文摘The effects of the grinding mode,fineness,gypsum kinds and dosage,mix proportions on properties of the composite cements consisting of slag,fly ash,limestone and a lower content clinker were investigated,respectively.The results show that when the proportions among slag,fly ash and limestone are appropriate,the grinding technology and system are reasonable,the optimized gypsums and additives are effective,the 52.5R grade cement (52.5R grade cement means a higher strength than 52.5 at early age) can be prepared by clinker dosage of 50% in weight,the 42.5R or 42.5,32.5 grade composite cement containing 40% and 30% clinker also may be made, respectively.Moreover,the high performance concrete prepared from the above composite cements was studied experimentally.
基金the Ministry of Science, Technology and Innovation (MOSTI), Government of Malaysia and University of Malaya for providing the funds to support this research work
文摘The performance of industrial waste incineration bottom ash in controlled low-strength material (CLSM) was investigated in this paper, as the quarry dust was added. CLSM mixtures were made from the industrial waste incineration bottom ash, quarry dust, and cement. Tests for fresh density, bleeding, compressive strength, shear strength, hydraulic conductivity, and excavatability were carried out. The com-pressive strength ranges from 60 kPa to 6790 kPa, the friction angle varies from 5° to 19°, and the cohesion is from 4 to 604 kPa. Most of the mixtures are found to be non-excavatable. It is indicated that the quarry dust addition increases the compressive strength and shear parame-ters, decreases bleeding, and increases the removability modulus.
基金Item Sponsored by National Natural Science Foundation of China (50234040)
文摘M, a particular industrial waste, was selected to detoxify chromium slag at a high temperature. The carbon remaining in M reduced Cr （Ⅵ） of Na2CrO4 borne in the chromium slag to Cr （Ⅲ） in the solid phase reaction, and its thermodynamics and kinetics were studied. The reduction process of Na2CrO4 by carbon produced CO, which was endothermic. Under the experimental condition, the apparent activation energy was 4.41 kJ·mol -1 , the apparent order of reaction for Na2CrO4 was equal to one, and the partial pressure of CO was only 0.22 Pa at 1 330 ℃.
文摘Destruction of industrial waste in cement rotary kilins(CRKs) is an alternative technology for the treatment of certain types of industrial waste(IW).In this paper,three typical types of industrial wastes were co-incinerated in the CRK at Beijing Cement Plant to determine the effects of waste disposal(especially solid waste disposal )on the quality of clinker and the concentration of pollutants in air emission.Experimental results show that(1) waste disposal does not affect the quality of clinker and fly ash,and fly ash after the IW disposal can still be used in the cement production,(2) heavy metals from IW are immobilized and stabilized in the clinker and cement,and (3) concentration of pollutants in air emission is far below than the permitted values in the China National Standard-Air Pollutants Emission Standard(GB 16297-1996).
文摘This paper deals briefly with the pollution caused by hazardous wastes in China, the hazardous waste management at present and the strategy that should be taken for hazardous waste management in the future. Hazardous waste problem has become one of the important environmental concerns in China. Hazardous waste have resulted in ecological and environmental destruction, caused damage to human health, and restricted economic development. Although a great effort has been devoted to the management of hazardous wastes, there remain many issues in legislation, experience, technology and finance to be solved. Some recommendations are made on the strategic measures for improving the hazardous waste management in China, particularly relating to legislation, technical development and international cooperation.
文摘This article describes the investigation of hazardous waste (HW) in the Three Gorges Area of Chongqing region, which indicates that by May 2002, the dumped HW therein amounted to 14 600 t and was mainly distributed in five districts and counties with 11 000 t in Fuling, 1 650 t in Fengdu, 950 t in Wanzhou; 630 t in Wushan and 430 t in Yunyang. The total amount was composed of 9 670 t chromic residue, 2 310 t waste oil and residue, 410 t waste (false) fertilizer, 28 t waste chemical medicine, 26 t waste materials and 2 200 t other things including acid residue, waste asbestos, fluorine silicate, pigment, additive, waste acid, alkali, nitric acid, vitriol, lead mud, storage battery, calcium carbide, potassium cyanide, polluted soil, discard dynamite, waste packing barrel of cyanides, etc. In all of the HW, 578 t can be treated by chemical neutralization and stabilization technology such as redox, chemical precipitation, acid and alkali neutralization, etc., and the rest is temporarily untreatble and should be removed and piled at a temporary storage site above the 177 m water level of the dam with an aim to be transported to a future disposal site for innocuous treatment.
文摘[Objective] This paper aimed to study the rapid identification method of hazardous wastes from illegal oil refining,and provide a new theoretical basis and practical basis for shortening the appraisal cycle and reducing the cost of identification.[Method] The identified substance and the qualified oil products were diluted by carbon disulfide with a ratio of 1∶100 for the gas chromatographic analysis.According to the corresponding national standard,the oil change indexes,such as the moisture content,viscosity,acid value and mechanical impurities of the identified substance,were measured.[Result] By the comparison between the gas chromatogram spectrograms of the identified substance and the qualified oil,it is found that the main component of the identified substance was the mineral oils.And the test results of oil change index showed that the mineral oil was unqualified.[Conclusion] This method was of great significance to save the cost of appraisal and improve the efficiency of case handling.
基金supported by the National Key R&D Program of China(No.2018YFC1902600)。
文摘As industrialization accelerates and the amount of hazardous waste generated gradually increases,the means of disposal of hazardous waste is of increasing concern.In this paper,a 40 t/d counter-fow rotary kiln incineration system owned by a Jiangsu environmental protection company was researched.The software Aspen Plus was used to build the mixed pyrolysis model and the software Fluent was used to build the computational fuid dynamics model of the incineration system.The infuence of the calorifc value of the hazardous waste,the operating temperature and the air supply on the operational efectiveness of the incineration system were analyzed by varying the simulation conditions.The results show that the SO_(x)and NO_(x)content of the product is lower when the operating temperature is above 800℃.The incineration system could only operate above 800℃when the calorifc value of the hazardous waste is not less than 1500 kcal/kg.The incineration system operated best at a primary air velocity of 1.5 m/s.The simulation results in this paper serve as a guide for the operation of counter-fow rotary kiln incineration systems.
文摘Nowadays, with regard to environmental issues, proper operation of wastewater treatment plants is of particular importance that in the case of inappropriate utilization, they will cause serious problems. Processes that exist in environmental systems and environmental engineers are dealing with them mostly have two major characteristics: they are dependent on many variables;and there are complex relationships between its components which make them very difficult to analyze. Being familiar with characteristics of industrial town effluents from various wastewater treatment units, which have high qualitative and quantitative variations and more uncertainties compared to urban wastewaters, plays very effective role in governing them. In order to achieve a better and efficient control over the operation of an industrial wastewater treatment plant, powerful mathematical tool can be used that is based on recorded data from some basic parameters of wastewater during a period of treatment plant operation. In this study, the multilayer perceptron (MLP) feed forward neural network with a hidden layer and stop training method was used to predict quality parameters of the industrial effluent. Data of this study are related to the Fajr Industrial Wastewater Treatment Plant located in Mahshahr—Iran that qualitative and quantitative characteristics of its units were used for training, calibration and evaluation of the neural model. Also, Principal Component Analysis technique was applied to modify and improve performance of generated models of neural networks. The results of this model showed good accuracy of the model in estimating qualitative pro- file of wastewater. This model facilitates evaluating the performance of each treatment plant units through comparing the results of prediction model with the standard amount of output.
基金the Deutsche Forschungsgemeinschaft for funding this research project.
文摘Zeolite synthesis was studied using two silica rich filtration residues (FR 1 and FR 2) as Si-source and sodium aluminate in a direct synthesis at 60°C at strong alkaline conditions (8 M - 16 M NaOH). In addition to these one-pot syntheses, a two-step process was investigated. Here, an alkaline digestion of FR at 60°C was followed by gel precipitation with sodium aluminate and gel crystallization under usual conditions of 80°C - 90°C. The results show that the substitution of chemical reagent sodium silicate by a waste material like FR as Si-source is possible but requires fine tuning of the reaction conditions as zeolite crystallization is a process under kinetic control. The solubility behaviour and impurities of the inserted filtration residues strongly influenced the course of reaction. Thus zeolites like hydrosodalite or intermediate zeolite between cancrinite and sodalite, or zeolite NaA or Z-21 in cocrystallization with hydrosodalite could be observed in the one pot syntheses already in a short time interval between 1 - 4 h depending on the alkalinity. The two step process yield to zeolites NaA and NaX in very good quality. The reaction process of FR in both reaction methods was characterized by chemical analyses, X-ray powder diffraction, Fourier transform infrared spectroscopy as well as scanning electron microscopy. Surface area and water content of selected products were further characterized by the BET-method and by thermogravimetry. Summing up the results, we can show that zeolite formation from filtration residues is possible by several reaction procedures as model cases for a re-use of industrial waste materials. Beside the importance for environmental protection, the reactions are of interest for zeolite chemistry as the re-use of FR is possible under economically conditions of low energy consumption at 60°C and short reaction periods.
