Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), sc...Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), scanning electron microscopy(SEM), and electron backscatter diffraction(EBSD).The coating bonding strength is assessed by pull-out tests and scribing in accordance with GB/T 9286-1998.The results show that the Cu coating with a thickness of 30 μm deposited on GF/PEEK by magnetron sputtering has lower roughness, finer grain size, higher crystallinity, as well as better macroscopic compressive stress,bonding strength, and electrical conductivity than the Cu coating deposited by electroplating.展开更多
Pure cobalt(Co)thin films were fabricated by direct current magnetron sputtering,and the effects of sputtering power and pres-sure on the microstructure and electromagnetic properties of the films were investigated.As...Pure cobalt(Co)thin films were fabricated by direct current magnetron sputtering,and the effects of sputtering power and pres-sure on the microstructure and electromagnetic properties of the films were investigated.As the sputtering power increases from 15 to 60 W,the Co thin films transition from an amorphous to a polycrystalline state,accompanied by an increase in the intercrystal pore width.Simultaneously,the resistivity decreases from 276 to 99μΩ·cm,coercivity increases from 162 to 293 Oe,and in-plane magnetic aniso-tropy disappears.As the sputtering pressure decreases from 1.6 to 0.2 Pa,grain size significantly increases,resistivity significantly de-creases,and the coercivity significantly increases(from 67 to 280 Oe),which can be attributed to the increase in defect width.Corres-pondingly,a quantitative model for the coercivity of Co thin films was formulated.The polycrystalline films sputtered under pressures of 0.2 and 0.4 Pa exhibit significant in-plane magnetic anisotropy,which is primarily attributable to increased microstress.展开更多
Al_(1-x)In_(x)N, a Ⅲ-nitride semiconductor material, is currently of great research interest due to its remarkable physical properties and chemical stability. When the Al and In compositions are tuned, its band-gap e...Al_(1-x)In_(x)N, a Ⅲ-nitride semiconductor material, is currently of great research interest due to its remarkable physical properties and chemical stability. When the Al and In compositions are tuned, its band-gap energy varies from 0.7 eV to 6.2 eV, which shows great potential for application in photodetectors. Here, we report the fabrication and performance evaluation of integrated Al_(1-x)In_(x)N on a free-standing GaN substrate through direct radio-frequency magnetron sputtering.The optical properties of Al_(1-x)In_(x)N will be enhanced by the polarization effect of a heterostructure composed of Al_(1-x)In_(x)N and other Ⅲ-nitride materials. An Al_(1-x)In_(x)N/Ga N visible-light photodetector was prepared by semiconductor fabrication technologies such as lithography and metal deposition. The highest photoresponsivity achieved was 1.52 A·W^(-1)under 365 nm wavelength illumination and the photodetector was determined to have the composition Al0.75In0.25N/GaN.A rise time of 0.55 s was observed after transient analysis of the device. The prepared Al_(1-x)In_(x)N visible-light photodetector had a low dark current, high photoresponsivity and fast response speed. By promoting a low-cost, simple fabrication method,this study expands the application of ternary alloy Al_(1-x)In_(x)N visible-light photodetectors in optical communication.展开更多
The frequency characteristics of free oscillation magnetron(FOM) and injection-locked magnetron(ILM) are theoretically investigated.By using the equal power voltage obtained from the experiment data,expressions of the...The frequency characteristics of free oscillation magnetron(FOM) and injection-locked magnetron(ILM) are theoretically investigated.By using the equal power voltage obtained from the experiment data,expressions of the frequency and radio frequency(RF) voltage of FOM and ILM,as well as the locking bandwidth,on the anode voltage and magnetic field are derived.With the increase of the anode voltage and the decrease of the magnetic field,the power and its growth rate increase,while the frequency increases and its growth rate decreases.The theoretical frequency and power of FOM agree with the particle-in-cell(PIC) simulation results.Besides,the theoretical trends of the power and frequency with the anode voltage and magnetic field are consistent with the experimental results,which verifies the accuracy of the theory.The theory provides a novel calculation method of frequency characteristics.It can approximately analyze the power and frequency of both FOM and ILM,which promotes the industrial applications of magnetron and microwave energy.展开更多
By generating closed-loop electron E × B drift over the front and back surface of a band magnetron cathode, a uniform magnetron plasma can be formed over the front surface. Here, we attempted to generate a unifor...By generating closed-loop electron E × B drift over the front and back surface of a band magnetron cathode, a uniform magnetron plasma can be formed over the front surface. Here, we attempted to generate a uniform supermagnetron plasma under a stationary magnetic field by situating two such band magnetron cathodes face-to-face in parallel. Performing uniform supermagnetron plasma chemical vapor deposition (CVD) with tetraethylorthosilicate (TEOS)/O2 CVD, SiO2 films with good uniformity (±5%) at the central region of the cathode could be achieved under a stationary magnetic field of about 160 G. Using this supermagnetron plasma CVD apparatus, a-CNx:H films were then deposited to investigate their characteristics using isobutane (i-C4H10)/N2 mixed gases. A relatively high deposition rate of about 100 nm/min was obtained. The a-CNx:H films obtained had a hardness of about 25 GPa, higher than that of glass (22 GPa).展开更多
The CrN and Cr-Al-Si-N films were deposited on Si wafer and SUS 304 substrates by a hybrid coating system with high power impulse magnetron sputtering (HIPIMS) and a DC pulse sputtering using Cr and AlSi targets under...The CrN and Cr-Al-Si-N films were deposited on Si wafer and SUS 304 substrates by a hybrid coating system with high power impulse magnetron sputtering (HIPIMS) and a DC pulse sputtering using Cr and AlSi targets under N2/Ar atmosphere.By varying the sputtering current of the AlSi target in the range of 0-2.5 A,both the Al and Si contents in the films increased gradually from 0 to 19.1% and 11.1% (mole fraction),respectively.The influences of the AlSi cathode DC pulse current on the microstructure,phase constituents,mechanical properties,and oxidation behaviors of the Cr-Al-Si-N films were investigated systematically.The results indicate that the as-deposited Cr-Al-Si-N films possess the typical nanocomposite structure,namely the face centered cubic (Cr,Al)N nano-crystallites are embedded in the amorphous Si3N4 matrix.With increasing the Al and Si contents,the hardness of the film first increases from 20.8 GPa for the CrN film to the peak value of 29.4 GPa for the Cr0.23Al0.14Si0.07 N film,and then decreases gradually.In the meanwhile,the Cr0.23Al0.14Si0.07N film also possesses excellent high-temperature oxidation resistance that is much better than that of the CrN film at 900 or 1000 °C.展开更多
Cu films with thickness of 630-1300nm were deposited on glass substrates withoutheating by DC magnetron sputtering in pure Ar gas. Ar pressure was controlled to0.5, 1.0 and 1.5Pa respectively. The target voltage was f...Cu films with thickness of 630-1300nm were deposited on glass substrates withoutheating by DC magnetron sputtering in pure Ar gas. Ar pressure was controlled to0.5, 1.0 and 1.5Pa respectively. The target voltage was fixed at 500V but the targetcurrent increased from 200 to 1150mA with Ar pressure increasing. X-ray diffrac-tion, scanning electron microscopy and atomic force microscopy were used to observethe structural characterization of the films. The resistivity of the films was measuredusing four-point probe technique. At all the Ar pressures, the Cu films have mixturecrystalline orientations of [111], [200] and [220] in the direction of the film growth.The film deposited at lower pressure shows more [111] orientation while that depositedat higher pressure has more [220] orientation. The amount of larger grains in the filmprepared at 0.5Pa Ar pressure is slightly less than that prepared at 1. 0Pa and 1.5PaAr pressures. The resistivities of the films prepared at three different Ar pressures rep-resent few differences, about 3-4 times of that of bulk material. Besides the depositionrate increases with Ar pressure because of the increase in target current. The contri-bution of the bombardment of energetic reflected Argon atoms to these phenomena isdiscussed.展开更多
Low resistivity and highly transparent ITO conducting films for solar cell applications were fabricated at low temperature by r.f. magnetron sputtering. ITO films were deposited on glass and silicon substrate. Electri...Low resistivity and highly transparent ITO conducting films for solar cell applications were fabricated at low temperature by r.f. magnetron sputtering. ITO films were deposited on glass and silicon substrate. Electrical, optical, structural and morphological properties of the ITO films were investigated in terms of the preparation conditions. The annealing treatment has improved the properties of the ITO films at different degree. The maximum transmittance of the obtained ITO films in the visible range is over 92%, and the low resistivity for the ITO films are about 3.85×10-4 Ω·cm at 80 ℃, 80 W after annealing.展开更多
Ni-Cr System solar selective thin solid films were prepared by d.c. magnetron reactive sputtering under the atmosphere of O2 and N2. Ni-Cr alloy was chosen as target material and copper sheets as substrate. Using SEAL...Ni-Cr System solar selective thin solid films were prepared by d.c. magnetron reactive sputtering under the atmosphere of O2 and N2. Ni-Cr alloy was chosen as target material and copper sheets as substrate. Using SEAL Spectrophotometer and Talystep to analyze the relations between the selective characteristic and the structure, the formation and the thickness of the thin films. The aim is to obtain good solar selective thin films with high absorptance and low emittance, which is applied to flat plate solar heat collectors.展开更多
The effects of substrate temperature and deposition time on the morphology and corrosion resistance of FeCoCrNiMo0.3 coating fabricated by magnetron sputtering were investigated by scanning electron microscopy and ele...The effects of substrate temperature and deposition time on the morphology and corrosion resistance of FeCoCrNiMo0.3 coating fabricated by magnetron sputtering were investigated by scanning electron microscopy and electrochemical tests.The FeCoCrNiMo0.3 coating was mainly composed of the face-centered cubic phase.High substrate temperature promoted the densification of the coating,and the pitting resistance and protective ability of the coating in 3.5wt%NaCl solution was thus improved.When the deposition time was prolonged at 500℃,the thickness of the coating remarkably increased.Meanwhile,the pitting resistance improved as the deposition time increased from 1 to 3 h;however,further improvement could not be obtained for the coating sputtered for 5 h.Overall,the pitting resistance of the FeCoCrNiMo0.3 coating sputtered at 500℃for 3 h exceeds those of most of the reported high-entropy alloy coatings.展开更多
Pseudobinary Ti 1 x Al x N films were synthesized on Si (100) wafer by DC magnetron sputtering method using Ti 1 x Al x alloy targets with different Al contents. The composition of the Ti 1 x Al x N films was determin...Pseudobinary Ti 1 x Al x N films were synthesized on Si (100) wafer by DC magnetron sputtering method using Ti 1 x Al x alloy targets with different Al contents. The composition of the Ti 1 x Al x N films was determined by electron probe microanalysis (EPMA). Structural characteristic was performed by X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution TEM (HRTEM). First principles virtual crystal calculations for the Ti 1 x Al x N disordered alloys were used for the XRD simulations. The crystalline structure of the Ti 0.61 Al 0.39 N film was found to be a metastable single phase with NaCl (B1) structure. Its lattice constant, determined by XRD, was less than that of pure TiN. With the increase of Al content, the lattice constant of B1 phase was continually decreased, while würtzite (B4) structure was observed in the Ti 0.40 Al 0.60 N film. When x reached 0.75, the B1 phase disappeared, and only B4 phase was remained. The critical Al content for the phase transition from NaCl to würtzite structure in this paper was about 0.60, which could be explained by both the thermodynamic model and the electron theory. As-deposited Ti 1 x Al x N films exhibited excellent mechanical properties. Hardness measurements of Ti 1 x Al x N films showed a high value of 45GPa for x=0.39 and was decreased to value of 27 GPa with increasing Al at x=0.60.展开更多
Ternary AlMgB thin films were synthesized on silicon (100) substrate at 573 K by radio frequency (RF) magnetron sputtering method using one Al/Mg co-target and one boron target. The thickness of the as-deposited thin ...Ternary AlMgB thin films were synthesized on silicon (100) substrate at 573 K by radio frequency (RF) magnetron sputtering method using one Al/Mg co-target and one boron target. The thickness of the as-deposited thin film was controlled to 500 nm by adjusting deposition time. The influences of sputtering powers on the elemental contents and structural and mechanical properties were investigated by electron probe microanalysis (EPMA), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), and nanoindentation system. At the same time, the ball-on-disk tribometer was used to measure the friction behavior of the films. Experimental results indicate that the as-deposited boron-rich films are primarily amorphous structure and possess a dramatic high hardness up to 39 GPa with 99.03 at.% boron. Obviously, it has exceeded the hardness value of 32 GPa of pure AlMgB 14 bulk material prepared by sintering method. Furthermore, the friction coefficients of the thin films exhibit an average value as low as 0.3, which is considered as the effect of self-lubricating.展开更多
Diamond-like carbon (DLC) films have excellent mechanical and chemical properties similar to those of crystalline diamond giving them wide applications as protective coatings. So far, a variety of methods are employed...Diamond-like carbon (DLC) films have excellent mechanical and chemical properties similar to those of crystalline diamond giving them wide applications as protective coatings. So far, a variety of methods are employed to deposit DLC films. In this study, DLC films with different thicknesses were deposited on Si and glass substrates using RF magnetron PECVD method with C 4 H 10 as carbon source. The bonding microstructure, surface morphology and tribological properties at different growing stages of the DLC films were tested. Raman spectra were deconvoluted into D peak at about 1370 cm 1 and G peak around 1590 cm 1 , indicating typical features of the DLC films. A linear relationship between the film thickness and the deposition time was found, revealing that the required film thickness may be obtained by the appropriate tune of the deposition time. The concentration of sp 3 and sp 2 carbon atoms in the DLC films was measured by XPS spectra. As the films grew, the sp 3 carbon atoms decreased while sp 2 atoms increased. Surface morphology of the DLC films clearly showed that the films were composed of spherical carbon clusters, which tended to congregate as the deposition time increased. The friction coefficient of the films was very low and an increase was also found with the increase of film thickness corresponding to the results of XPS spectra. The scratch test proved that there was good bonding between the DLC films and the substrates.展开更多
Indium tin oxide （ITO） films were prepared on polyester, Si and glass substrate with relatively high deposition rate of above 0.9 nm/s by DC reactive magnetron sputtering technique at the sputtering pressure of 0.06...Indium tin oxide （ITO） films were prepared on polyester, Si and glass substrate with relatively high deposition rate of above 0.9 nm/s by DC reactive magnetron sputtering technique at the sputtering pressure of 0.06 Pa system, respectively. The dependence of resistivity on deposition parameters, such as deposition rate, target-to-substrate distance （TSD）, oxygen flow rate and sputtering time （thickness）, has been investigated, together with the structural and the optical properties. It was revealed that all ITO films exhibited lattice expansion. The resistivity of ITO thin films shows significant substrate effect: much lower resistivity and broader process window have been reproducibly achieved for the deposition of ITO films onto polyester rather than those prepared on both Si and glass substrates. The films with resistivity of as low as 4.23 ?10-4 Ω.cm and average transmittance of -78% at wavelength of 400-700 nm have been achieved for the films on polyester at room temperature.展开更多
The excellent physical and chemical properties of cubic boron nitride(c-BN) film make it a promising candidate for various industry applications. However, the c-BN film thickness restricts its practical applications i...The excellent physical and chemical properties of cubic boron nitride(c-BN) film make it a promising candidate for various industry applications. However, the c-BN film thickness restricts its practical applications in many cases. Thus, it is indispensable to develop an economic, simple and environment-friend way to synthesize high-quality thick, stable c-BN films. High-cubic-content BN films are prepared on silicon(100) substrates by radio frequency(RF) magnetron sputtering from an h-BN target at low substrate temperature. Adhesions of the c-BN films are greatly improved by adding hydrogen to the argon/nitrogen gas mixture, allowing the deposition of a film up to 5-μm thick. The compositions and the microstructure morphologies of the c-BN films grown at different substrate temperatures are systematically investigated with respect to the ratio of H_2 gas content to total working gas. In addition, a primary mechanism for the deposition of thick c-BN film is proposed.展开更多
Carbon nitride(CN_x) films supported on fluorine-doped tin oxide(FTO) glass are prepared by radio frequency magnetron sputtering, in which the film thicknesses are 90-100 nm, and the element components in the CNX film...Carbon nitride(CN_x) films supported on fluorine-doped tin oxide(FTO) glass are prepared by radio frequency magnetron sputtering, in which the film thicknesses are 90-100 nm, and the element components in the CNX films are in the range of x = 0.15-0.25. The as-prepared CN_x is for the first time used as counter electrode for dye-sensitized solar cells(DSSCs), and show a preparation-temperature dependent electrochemical performance. X-ray photoelectron spectroscopy(XPS) demonstrates that there is a higher proportion of sp^2 C=C and sp^3 C-N hybridized bonds in CN_x-500(the sample treated at 500 ℃) than in CNX-RT(the sample without a heat treatment). It is proposed that the sp^2 C=C and sp^3 C-N hybridized bonds in the CN_x films are helpful for improving the electrocatalytic activities in DSSCs. Meanwhile, Raman spectra also prove that CN_x-500 has a relatively high graphitization level that means an increasing electrical conductivity. This further explains why the sample after the heat treatment has a higher electrochemical performance in DSSCs. In addition, the as-prepared CN_x counter electrodes have a good light transmittance in the visible light region. The results are meaningful for developing low-cost metal-free transparent counter electrodes for DSSCs.展开更多
To date,lithium-ion batteries are becoming increasingly significant in the application of portable devices and electrical vehicles,and revolutionary progress in theoretical research and industrial application has been...To date,lithium-ion batteries are becoming increasingly significant in the application of portable devices and electrical vehicles,and revolutionary progress in theoretical research and industrial application has been achieved.However,the commercial polyolefin separators with unsatisfying electrolytes affinity and poor thermal stability have extremely restricted the further application of lithium-ion batteries,especially in the high-temperature fields.In this work,magnetron sputtering deposition technique is employed to modify the commercial polyimide separator by coating silicon nitride on both sides.Magnetron sputtering deposition modified polyimide(MSD-PI)composite separator shows high thermal stability and ionic conductivity.More importantly,compared with the cells using Celgard separator,the cells with MSD-PI separator exhibit superior electrochemical performance,especially long-term cycle performance under high temperature environment,owing to the high thermal conductivity of surface Si3 N4 particles.Hence,lithium-ion batteries with MSD-PI separator are capable of improving thermal safety and capacity retention,which demonstrates that magnetron sputtering deposition technique could be regarded as a promising strategy to develop advanced organic/inorganic composite separators for high-temperature lithium-ion batteries.展开更多
Radio frequency(RF) reactive magnetron sputtering was utilized to deposit Li-doped and undoped zinc oxide(Zn O) films on silicon wafers. Various Ar/O2 gas ratios by volume and sputtering powers were selected for each ...Radio frequency(RF) reactive magnetron sputtering was utilized to deposit Li-doped and undoped zinc oxide(Zn O) films on silicon wafers. Various Ar/O2 gas ratios by volume and sputtering powers were selected for each deposition process. The results demonstrate that the enhanced Zn O films are obtained via Li doping. The average deposition rate for doped Zn O films is twice more than that of the undoped films. Both atomic force microscopy and scanning electron microscopy studies indicate that Li doping significantly contributes to the higher degree of crystallinity of wurtzite–Zn O. X-ray diffraction analysis demonstrates that Li doping promotes the(002) preferential orientation in Li-doped Zn O films. However, an increase in the Zn O lattice constant, broadening of the(002) peak and a decrease in the peak integral area are observed in some Li-doped samples, especially as the form of Li2 O. This implies that doping with Li expands the crystal structure and thus induces the additional strain in the crystal lattice. The oriented-growth Li-doped Zn O will make significant applications in future surface acoustic wave devices.展开更多
An accelerator storage ring needs clean ultrahigh vacuum.A TiZrV non-evaporable getter(NEG) film deposited on interior walls of the chamber can realize distributed pumping,effective vacuum improvement and reduced long...An accelerator storage ring needs clean ultrahigh vacuum.A TiZrV non-evaporable getter(NEG) film deposited on interior walls of the chamber can realize distributed pumping,effective vacuum improvement and reduced longitudinal pressure gradient.But accumulation of pollutants such as N_2 and O_2 will decrease the adsorption ability of the NEG,leading to a reduction of NEG lifetime.Therefore,an NEG thin film coated with a layer of Pd,which has high diffusion rate and absorption ability for H_2,can extend the service life of NEG and improve the pumping rate of H_2 as well.In this paper,with argon as discharge gas,a magnetron sputtering method is adopted to prepare TiZrV-Pd films in a long straight pipe.By SEM measurement,deposition rates of TiZrV-Pd films are analyzed under different deposition parameters,such as magnetic field strength,gas flow rate,discharge current,discharge voltage and working pressure.By comparing the experimental results with the simulation results based on Sigmund's theory,the Pd deposition rate C can be estimated by the sputtered depth.展开更多
We improved the photovoltaic properties of Cu_2O-based heterojunction solar cells using n-type oxide semiconductor thin films prepared by a sputtering apparatus with our newly developed multi-chamber system. We also o...We improved the photovoltaic properties of Cu_2O-based heterojunction solar cells using n-type oxide semiconductor thin films prepared by a sputtering apparatus with our newly developed multi-chamber system. We also obtained the highest efficiency(3.21%) in an AZO/p-Cu_2O heterojunction solar cell prepared with optimized pre-sputtering conditions using our newly developed multi-chamber sputtering system. This value achieves the same or higher characteristics than AZO/Cu_2O solar cells with a similar structure prepared by the pulse laser deposition method.展开更多
基金Funded by Shenzhen-Hong Kong Innovative Collaborative Research and Development Program (Nos.SGLH20181109 110802117, CityU 9240014)Innovation Project of Southwestern Institute of Physics (Nos.202001XWCXYD002, 202301XWCX003)CNNC Young Talent Program (No.2023JZYF-01)。
文摘Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), scanning electron microscopy(SEM), and electron backscatter diffraction(EBSD).The coating bonding strength is assessed by pull-out tests and scribing in accordance with GB/T 9286-1998.The results show that the Cu coating with a thickness of 30 μm deposited on GF/PEEK by magnetron sputtering has lower roughness, finer grain size, higher crystallinity, as well as better macroscopic compressive stress,bonding strength, and electrical conductivity than the Cu coating deposited by electroplating.
基金the financial support from the National Key Research and Development Program of China(No.2017YFB0305500)the State Key Laboratory of Powder Metallurgy,Central South University,Changsha,China.
文摘Pure cobalt(Co)thin films were fabricated by direct current magnetron sputtering,and the effects of sputtering power and pres-sure on the microstructure and electromagnetic properties of the films were investigated.As the sputtering power increases from 15 to 60 W,the Co thin films transition from an amorphous to a polycrystalline state,accompanied by an increase in the intercrystal pore width.Simultaneously,the resistivity decreases from 276 to 99μΩ·cm,coercivity increases from 162 to 293 Oe,and in-plane magnetic aniso-tropy disappears.As the sputtering pressure decreases from 1.6 to 0.2 Pa,grain size significantly increases,resistivity significantly de-creases,and the coercivity significantly increases(from 67 to 280 Oe),which can be attributed to the increase in defect width.Corres-pondingly,a quantitative model for the coercivity of Co thin films was formulated.The polycrystalline films sputtered under pressures of 0.2 and 0.4 Pa exhibit significant in-plane magnetic anisotropy,which is primarily attributable to increased microstress.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 61974144, 62004127, and 12074263)Key-Area Research and Development Program of Guangdong Province (Grant Nos. 2020B010174003 and 2020B010169001)+2 种基金Guangdong Science Foundation for Distinguished Young Scholars (Grant No. 2022B1515020073)the Science and Technology Foundation of Shenzhen (Grant No. JSGG20191129114216474)the Open Project of State Key Laboratory of Functional Materials for Informatics。
文摘Al_(1-x)In_(x)N, a Ⅲ-nitride semiconductor material, is currently of great research interest due to its remarkable physical properties and chemical stability. When the Al and In compositions are tuned, its band-gap energy varies from 0.7 eV to 6.2 eV, which shows great potential for application in photodetectors. Here, we report the fabrication and performance evaluation of integrated Al_(1-x)In_(x)N on a free-standing GaN substrate through direct radio-frequency magnetron sputtering.The optical properties of Al_(1-x)In_(x)N will be enhanced by the polarization effect of a heterostructure composed of Al_(1-x)In_(x)N and other Ⅲ-nitride materials. An Al_(1-x)In_(x)N/Ga N visible-light photodetector was prepared by semiconductor fabrication technologies such as lithography and metal deposition. The highest photoresponsivity achieved was 1.52 A·W^(-1)under 365 nm wavelength illumination and the photodetector was determined to have the composition Al0.75In0.25N/GaN.A rise time of 0.55 s was observed after transient analysis of the device. The prepared Al_(1-x)In_(x)N visible-light photodetector had a low dark current, high photoresponsivity and fast response speed. By promoting a low-cost, simple fabrication method,this study expands the application of ternary alloy Al_(1-x)In_(x)N visible-light photodetectors in optical communication.
基金Project supported by the National Basic Research Program of China(Grant No.2013CB328901)the National Natural Science Foundation of China(Grant No.11305177)
文摘The frequency characteristics of free oscillation magnetron(FOM) and injection-locked magnetron(ILM) are theoretically investigated.By using the equal power voltage obtained from the experiment data,expressions of the frequency and radio frequency(RF) voltage of FOM and ILM,as well as the locking bandwidth,on the anode voltage and magnetic field are derived.With the increase of the anode voltage and the decrease of the magnetic field,the power and its growth rate increase,while the frequency increases and its growth rate decreases.The theoretical frequency and power of FOM agree with the particle-in-cell(PIC) simulation results.Besides,the theoretical trends of the power and frequency with the anode voltage and magnetic field are consistent with the experimental results,which verifies the accuracy of the theory.The theory provides a novel calculation method of frequency characteristics.It can approximately analyze the power and frequency of both FOM and ILM,which promotes the industrial applications of magnetron and microwave energy.
文摘By generating closed-loop electron E × B drift over the front and back surface of a band magnetron cathode, a uniform magnetron plasma can be formed over the front surface. Here, we attempted to generate a uniform supermagnetron plasma under a stationary magnetic field by situating two such band magnetron cathodes face-to-face in parallel. Performing uniform supermagnetron plasma chemical vapor deposition (CVD) with tetraethylorthosilicate (TEOS)/O2 CVD, SiO2 films with good uniformity (±5%) at the central region of the cathode could be achieved under a stationary magnetic field of about 160 G. Using this supermagnetron plasma CVD apparatus, a-CNx:H films were then deposited to investigate their characteristics using isobutane (i-C4H10)/N2 mixed gases. A relatively high deposition rate of about 100 nm/min was obtained. The a-CNx:H films obtained had a hardness of about 25 GPa, higher than that of glass (22 GPa).
基金supported by a 2-Year Research Grant of Pusan National University,Korea
文摘The CrN and Cr-Al-Si-N films were deposited on Si wafer and SUS 304 substrates by a hybrid coating system with high power impulse magnetron sputtering (HIPIMS) and a DC pulse sputtering using Cr and AlSi targets under N2/Ar atmosphere.By varying the sputtering current of the AlSi target in the range of 0-2.5 A,both the Al and Si contents in the films increased gradually from 0 to 19.1% and 11.1% (mole fraction),respectively.The influences of the AlSi cathode DC pulse current on the microstructure,phase constituents,mechanical properties,and oxidation behaviors of the Cr-Al-Si-N films were investigated systematically.The results indicate that the as-deposited Cr-Al-Si-N films possess the typical nanocomposite structure,namely the face centered cubic (Cr,Al)N nano-crystallites are embedded in the amorphous Si3N4 matrix.With increasing the Al and Si contents,the hardness of the film first increases from 20.8 GPa for the CrN film to the peak value of 29.4 GPa for the Cr0.23Al0.14Si0.07 N film,and then decreases gradually.In the meanwhile,the Cr0.23Al0.14Si0.07N film also possesses excellent high-temperature oxidation resistance that is much better than that of the CrN film at 900 or 1000 °C.
基金The authors would like to thank Prof. Y.B. Wang and Mr. S. Liang of the Department of Material Physics for supporting AFM observations. The authors also would like to thank Ms. J.P. He of the State Key Laboratory for Advanced Metals and Materials for sup
文摘Cu films with thickness of 630-1300nm were deposited on glass substrates withoutheating by DC magnetron sputtering in pure Ar gas. Ar pressure was controlled to0.5, 1.0 and 1.5Pa respectively. The target voltage was fixed at 500V but the targetcurrent increased from 200 to 1150mA with Ar pressure increasing. X-ray diffrac-tion, scanning electron microscopy and atomic force microscopy were used to observethe structural characterization of the films. The resistivity of the films was measuredusing four-point probe technique. At all the Ar pressures, the Cu films have mixturecrystalline orientations of [111], [200] and [220] in the direction of the film growth.The film deposited at lower pressure shows more [111] orientation while that depositedat higher pressure has more [220] orientation. The amount of larger grains in the filmprepared at 0.5Pa Ar pressure is slightly less than that prepared at 1. 0Pa and 1.5PaAr pressures. The resistivities of the films prepared at three different Ar pressures rep-resent few differences, about 3-4 times of that of bulk material. Besides the depositionrate increases with Ar pressure because of the increase in target current. The contri-bution of the bombardment of energetic reflected Argon atoms to these phenomena isdiscussed.
基金This project was financially supported by the Natural Science Foundation of Hebei Province, China. (No. F2005000073).
文摘Low resistivity and highly transparent ITO conducting films for solar cell applications were fabricated at low temperature by r.f. magnetron sputtering. ITO films were deposited on glass and silicon substrate. Electrical, optical, structural and morphological properties of the ITO films were investigated in terms of the preparation conditions. The annealing treatment has improved the properties of the ITO films at different degree. The maximum transmittance of the obtained ITO films in the visible range is over 92%, and the low resistivity for the ITO films are about 3.85×10-4 Ω·cm at 80 ℃, 80 W after annealing.
基金supported by the Chinese Academy of Sciences within“The Hundred Talent Project"by the Bureau for Sciences and Technology of Guangzhou City within the"Nanoproject"
文摘Ni-Cr System solar selective thin solid films were prepared by d.c. magnetron reactive sputtering under the atmosphere of O2 and N2. Ni-Cr alloy was chosen as target material and copper sheets as substrate. Using SEAL Spectrophotometer and Talystep to analyze the relations between the selective characteristic and the structure, the formation and the thickness of the thin films. The aim is to obtain good solar selective thin films with high absorptance and low emittance, which is applied to flat plate solar heat collectors.
基金the National Science and Technology Major Project of China(No.2017-VII-0012-0109).
文摘The effects of substrate temperature and deposition time on the morphology and corrosion resistance of FeCoCrNiMo0.3 coating fabricated by magnetron sputtering were investigated by scanning electron microscopy and electrochemical tests.The FeCoCrNiMo0.3 coating was mainly composed of the face-centered cubic phase.High substrate temperature promoted the densification of the coating,and the pitting resistance and protective ability of the coating in 3.5wt%NaCl solution was thus improved.When the deposition time was prolonged at 500℃,the thickness of the coating remarkably increased.Meanwhile,the pitting resistance improved as the deposition time increased from 1 to 3 h;however,further improvement could not be obtained for the coating sputtered for 5 h.Overall,the pitting resistance of the FeCoCrNiMo0.3 coating sputtered at 500℃for 3 h exceeds those of most of the reported high-entropy alloy coatings.
基金supported by "University Innovation and Research Training Program (China)" (No. 2009003)the Natural Science Foundation of Jiangsu Province (No.BK2011252)the Industry Science and Technology Supported Plan of Changzhou (No. CE20110012)
文摘Pseudobinary Ti 1 x Al x N films were synthesized on Si (100) wafer by DC magnetron sputtering method using Ti 1 x Al x alloy targets with different Al contents. The composition of the Ti 1 x Al x N films was determined by electron probe microanalysis (EPMA). Structural characteristic was performed by X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution TEM (HRTEM). First principles virtual crystal calculations for the Ti 1 x Al x N disordered alloys were used for the XRD simulations. The crystalline structure of the Ti 0.61 Al 0.39 N film was found to be a metastable single phase with NaCl (B1) structure. Its lattice constant, determined by XRD, was less than that of pure TiN. With the increase of Al content, the lattice constant of B1 phase was continually decreased, while würtzite (B4) structure was observed in the Ti 0.40 Al 0.60 N film. When x reached 0.75, the B1 phase disappeared, and only B4 phase was remained. The critical Al content for the phase transition from NaCl to würtzite structure in this paper was about 0.60, which could be explained by both the thermodynamic model and the electron theory. As-deposited Ti 1 x Al x N films exhibited excellent mechanical properties. Hardness measurements of Ti 1 x Al x N films showed a high value of 45GPa for x=0.39 and was decreased to value of 27 GPa with increasing Al at x=0.60.
基金financially supported by the Fundamental Research Funds for the Central Universities (No.DUT10JN08)the Natural Science Foundation of Jiangsu Province (No. BK2011252)the Industry Science and Technology Supported Plan of Changzhou (No. CE20110012)
文摘Ternary AlMgB thin films were synthesized on silicon (100) substrate at 573 K by radio frequency (RF) magnetron sputtering method using one Al/Mg co-target and one boron target. The thickness of the as-deposited thin film was controlled to 500 nm by adjusting deposition time. The influences of sputtering powers on the elemental contents and structural and mechanical properties were investigated by electron probe microanalysis (EPMA), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), and nanoindentation system. At the same time, the ball-on-disk tribometer was used to measure the friction behavior of the films. Experimental results indicate that the as-deposited boron-rich films are primarily amorphous structure and possess a dramatic high hardness up to 39 GPa with 99.03 at.% boron. Obviously, it has exceeded the hardness value of 32 GPa of pure AlMgB 14 bulk material prepared by sintering method. Furthermore, the friction coefficients of the thin films exhibit an average value as low as 0.3, which is considered as the effect of self-lubricating.
基金supported by the National Natural Science Foundation of China (Nos. 50972078 and 51002090)the Outstanding Young Scientist Research Award Fund of Shandong Province (No. BS2010CL028)
文摘Diamond-like carbon (DLC) films have excellent mechanical and chemical properties similar to those of crystalline diamond giving them wide applications as protective coatings. So far, a variety of methods are employed to deposit DLC films. In this study, DLC films with different thicknesses were deposited on Si and glass substrates using RF magnetron PECVD method with C 4 H 10 as carbon source. The bonding microstructure, surface morphology and tribological properties at different growing stages of the DLC films were tested. Raman spectra were deconvoluted into D peak at about 1370 cm 1 and G peak around 1590 cm 1 , indicating typical features of the DLC films. A linear relationship between the film thickness and the deposition time was found, revealing that the required film thickness may be obtained by the appropriate tune of the deposition time. The concentration of sp 3 and sp 2 carbon atoms in the DLC films was measured by XPS spectra. As the films grew, the sp 3 carbon atoms decreased while sp 2 atoms increased. Surface morphology of the DLC films clearly showed that the films were composed of spherical carbon clusters, which tended to congregate as the deposition time increased. The friction coefficient of the films was very low and an increase was also found with the increase of film thickness corresponding to the results of XPS spectra. The scratch test proved that there was good bonding between the DLC films and the substrates.
文摘Indium tin oxide （ITO） films were prepared on polyester, Si and glass substrate with relatively high deposition rate of above 0.9 nm/s by DC reactive magnetron sputtering technique at the sputtering pressure of 0.06 Pa system, respectively. The dependence of resistivity on deposition parameters, such as deposition rate, target-to-substrate distance （TSD）, oxygen flow rate and sputtering time （thickness）, has been investigated, together with the structural and the optical properties. It was revealed that all ITO films exhibited lattice expansion. The resistivity of ITO thin films shows significant substrate effect: much lower resistivity and broader process window have been reproducibly achieved for the deposition of ITO films onto polyester rather than those prepared on both Si and glass substrates. The films with resistivity of as low as 4.23 ?10-4 Ω.cm and average transmittance of -78% at wavelength of 400-700 nm have been achieved for the films on polyester at room temperature.
基金supported by the National Natural Science Foundation of China(Grant Nos.51572105,61504046,and 51272224)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministry,China+1 种基金the Development and Reform Commission of Jilin Province,China(Grant No.2015Y050)the Scientific Research Foundation for the Returned Overseas of Jilin Province,China
文摘The excellent physical and chemical properties of cubic boron nitride(c-BN) film make it a promising candidate for various industry applications. However, the c-BN film thickness restricts its practical applications in many cases. Thus, it is indispensable to develop an economic, simple and environment-friend way to synthesize high-quality thick, stable c-BN films. High-cubic-content BN films are prepared on silicon(100) substrates by radio frequency(RF) magnetron sputtering from an h-BN target at low substrate temperature. Adhesions of the c-BN films are greatly improved by adding hydrogen to the argon/nitrogen gas mixture, allowing the deposition of a film up to 5-μm thick. The compositions and the microstructure morphologies of the c-BN films grown at different substrate temperatures are systematically investigated with respect to the ratio of H_2 gas content to total working gas. In addition, a primary mechanism for the deposition of thick c-BN film is proposed.
基金Financial support from the 973 Program (2015CB251100)NSFC (51001063)MOE Innovation Team (IRT13022)
文摘Carbon nitride(CN_x) films supported on fluorine-doped tin oxide(FTO) glass are prepared by radio frequency magnetron sputtering, in which the film thicknesses are 90-100 nm, and the element components in the CNX films are in the range of x = 0.15-0.25. The as-prepared CN_x is for the first time used as counter electrode for dye-sensitized solar cells(DSSCs), and show a preparation-temperature dependent electrochemical performance. X-ray photoelectron spectroscopy(XPS) demonstrates that there is a higher proportion of sp^2 C=C and sp^3 C-N hybridized bonds in CN_x-500(the sample treated at 500 ℃) than in CNX-RT(the sample without a heat treatment). It is proposed that the sp^2 C=C and sp^3 C-N hybridized bonds in the CN_x films are helpful for improving the electrocatalytic activities in DSSCs. Meanwhile, Raman spectra also prove that CN_x-500 has a relatively high graphitization level that means an increasing electrical conductivity. This further explains why the sample after the heat treatment has a higher electrochemical performance in DSSCs. In addition, the as-prepared CN_x counter electrodes have a good light transmittance in the visible light region. The results are meaningful for developing low-cost metal-free transparent counter electrodes for DSSCs.
基金supported by the National Natural Science Foundation of China(51704269 and 51573173)Fundamental Research Funds for the Central Universities(WK2320000037)。
文摘To date,lithium-ion batteries are becoming increasingly significant in the application of portable devices and electrical vehicles,and revolutionary progress in theoretical research and industrial application has been achieved.However,the commercial polyolefin separators with unsatisfying electrolytes affinity and poor thermal stability have extremely restricted the further application of lithium-ion batteries,especially in the high-temperature fields.In this work,magnetron sputtering deposition technique is employed to modify the commercial polyimide separator by coating silicon nitride on both sides.Magnetron sputtering deposition modified polyimide(MSD-PI)composite separator shows high thermal stability and ionic conductivity.More importantly,compared with the cells using Celgard separator,the cells with MSD-PI separator exhibit superior electrochemical performance,especially long-term cycle performance under high temperature environment,owing to the high thermal conductivity of surface Si3 N4 particles.Hence,lithium-ion batteries with MSD-PI separator are capable of improving thermal safety and capacity retention,which demonstrates that magnetron sputtering deposition technique could be regarded as a promising strategy to develop advanced organic/inorganic composite separators for high-temperature lithium-ion batteries.
基金financially supported by the National Natural Science Foundation of China(No.51272024)the China Postdoctoral Science Foundation(No.2014M560042)
文摘Radio frequency(RF) reactive magnetron sputtering was utilized to deposit Li-doped and undoped zinc oxide(Zn O) films on silicon wafers. Various Ar/O2 gas ratios by volume and sputtering powers were selected for each deposition process. The results demonstrate that the enhanced Zn O films are obtained via Li doping. The average deposition rate for doped Zn O films is twice more than that of the undoped films. Both atomic force microscopy and scanning electron microscopy studies indicate that Li doping significantly contributes to the higher degree of crystallinity of wurtzite–Zn O. X-ray diffraction analysis demonstrates that Li doping promotes the(002) preferential orientation in Li-doped Zn O films. However, an increase in the Zn O lattice constant, broadening of the(002) peak and a decrease in the peak integral area are observed in some Li-doped samples, especially as the form of Li2 O. This implies that doping with Li expands the crystal structure and thus induces the additional strain in the crystal lattice. The oriented-growth Li-doped Zn O will make significant applications in future surface acoustic wave devices.
基金supported by the National Natural Science Funds of China(No.11205155)Fundamental Research Funds for the Central Universities(WK2310000041)
文摘An accelerator storage ring needs clean ultrahigh vacuum.A TiZrV non-evaporable getter(NEG) film deposited on interior walls of the chamber can realize distributed pumping,effective vacuum improvement and reduced longitudinal pressure gradient.But accumulation of pollutants such as N_2 and O_2 will decrease the adsorption ability of the NEG,leading to a reduction of NEG lifetime.Therefore,an NEG thin film coated with a layer of Pd,which has high diffusion rate and absorption ability for H_2,can extend the service life of NEG and improve the pumping rate of H_2 as well.In this paper,with argon as discharge gas,a magnetron sputtering method is adopted to prepare TiZrV-Pd films in a long straight pipe.By SEM measurement,deposition rates of TiZrV-Pd films are analyzed under different deposition parameters,such as magnetic field strength,gas flow rate,discharge current,discharge voltage and working pressure.By comparing the experimental results with the simulation results based on Sigmund's theory,the Pd deposition rate C can be estimated by the sputtered depth.
基金partly supported by Grant-in-Aid for Scientific Research on Innovative Areas from the Ministry of Education, Culture, Sports, Science and Technology of Japan (No.15K04723)
文摘We improved the photovoltaic properties of Cu_2O-based heterojunction solar cells using n-type oxide semiconductor thin films prepared by a sputtering apparatus with our newly developed multi-chamber system. We also obtained the highest efficiency(3.21%) in an AZO/p-Cu_2O heterojunction solar cell prepared with optimized pre-sputtering conditions using our newly developed multi-chamber sputtering system. This value achieves the same or higher characteristics than AZO/Cu_2O solar cells with a similar structure prepared by the pulse laser deposition method.
