Conventionally available Polyvinyl acetate (PVAc) wood glues are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor strength at high humidity, poor strength at high temperature and workability at low-tempera...Conventionally available Polyvinyl acetate (PVAc) wood glues are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor strength at high humidity, poor strength at high temperature and workability at low-temperature. PVAc is non-resistant to high humidity, and if such adhesive bonds are exploited in a highly humid environment, its strength substantially decreases. Sufficiently water-resistant adhesive bonds are achieved by modifying PVAc dispersion with special chemicals like acrylic acid (AA) and N-methylol acrylamide (NMA) as a co-monomer, Silanes, and ethylene modified PVA. The Lewis acids like aluminium chloride and aluminium nitrate are used as cross-linkers. So PVAc adhesives are classified as reactive and non-reactive glue. Application of non-reactive D1 (as per EN 204-205) and reactive D2 and D3 (as per EN 204-205) adhesives for bonding laminate on plywood is a regular practice in the Indian market. In summer time, Crack formation was seen in laminate bonded with reactive D2 and D3 adhesives in regions where the room temperature was above 45°C. However, if the same laminate substrates were bonded with non-reactive D1, no cracks were seen. To analyse the above phenomenon, we have done Dynamic mechanical analysis of non-reactive D1, reactive D2 and D3 adhesive.展开更多
To improve the bearing pressure capacity of ultrahigh pressure apparatus,the internal autofrettaged cylinder with interlayer pressure(ACCIP)is introduced,and the analytical model for the ACCIP structure and its deriva...To improve the bearing pressure capacity of ultrahigh pressure apparatus,the internal autofrettaged cylinder with interlayer pressure(ACCIP)is introduced,and the analytical model for the ACCIP structure and its derivation are presented as well.Calculation showed that the ACCIP method enhance bearing pressure of the apparatus obviously;optimization results revealed that under the working pressure pw=1.07σs and different radius ratios,the ACCIP method can keep the apparatus in deformed-elastically state;And when the pw=1.07σs,the minimum radius ratio was approximate 3.29,in this case,no yielding happened.The above results demonstrate that the ACCIP method is a promising technique to improve the bearing pressure of ultrahigh pressure apparatus,and the analytical model for the ACCIP method is also reasonable.In addition,the minimum radius ratio ro/ri under randomly specified workload can be Fig.d out by the analytical model proposed in this work.展开更多
The mechanical state of cantilever gearbox housing is different from ordinary ones due to the long arm of force caused by cantilever structure.Conventional mechanical analysis methods either took cantilever gearbox ho...The mechanical state of cantilever gearbox housing is different from ordinary ones due to the long arm of force caused by cantilever structure.Conventional mechanical analysis methods either took cantilever gearbox housing as ordinary ones or cantilever beam.Few published papers have specially focused on mechanical analysis method for cantilever gearbox housing.This paper takes a longwall shearer cutting unit gearbox(SCUG)as an example and the mechanical analysis method is investigated according to the causes of fatigue for SCUG.Force analysis model is established for finding out regions of static fatigue caused by low-frequency loads,and local resonance analysis is used for finding out regions of vibration fatigue caused by high-frequency loads.Not only bending moment but also torque caused by gear meshing forces is taken into account in the force analysis model.Vibration response is obtained from cutting experiment,and dominant frequencies of local resonance are obtained by frequency domain analysis.Finite element model of SCUG is established,and natural frequencies and strain modes are analyzed for obtaining the main vibration modes corresponding to dominant frequencies.Hence,large stress regions caused by low and high frequency loads are obtained.Results show that the worst working condition is oblique cutting,and the stress of B-B in 600 mm cutting depth can reach 166 MPa.Obviously,950 Hz,1250 Hz,and 1400 Hz are dominant frequencies of SCUG(23rd,25th and 27th natural frequencies).Generally,this paper proposes some principles for mechanical analysis method of cantilever gearbox housing.展开更多
Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) a...Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) and sized short-glass fibres with two amino-silane coupling agents.The calcite particle content is 0, 11.7 and 23.5 vol. pct for the matrices. The glass fiber contentis 0, 10 and 15 vol. pct. The matrix materials and corresponding composites were compoundedusing a twin screw extruder and dumbbell-shaped tensile bars were prepared with an injectionmolding process. The tensile and flexural properties as well as the unnotched and notchedCharpy impact energies of short glass fibre/calcite/ABS composites were studied in this paper.The effects of fibres, fibre surface treatments and particles on these mechanical properties ofthe composites were discussed in detail. An importarit information was obtained, which is thatthe tensile and flexural strengths of hybrid SGF/calcite/ABS composites are the same as thoseof corresponding fibre composites when the ratio of the interfacial adhesion strength betweenparticles and matrix to that between fibres and matrix is higher than certain value. otherwise theformer are lower than the latter.展开更多
The transport of fluid, nutrients, and signaling molecules in the bone lacunar–canalicular system(LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching(F...The transport of fluid, nutrients, and signaling molecules in the bone lacunar–canalicular system(LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching(FRAP) approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30–50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis(FEA)approach. An intact murine tibia was first re-constructed from micro CT images into a three-dimensional(3D)linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform(FEBio) to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex.Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces(shear and drag forces) for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.展开更多
In this paper, a Web-based Mechanical Design and A na lysis Framework (WMDAF) is proposed. This WMADF allows designers to develop web -based computer aided programs in a systematic way during the collaborative mec han...In this paper, a Web-based Mechanical Design and A na lysis Framework (WMDAF) is proposed. This WMADF allows designers to develop web -based computer aided programs in a systematic way during the collaborative mec hanical system design and analysis process. This system is based on an emerg ing web-based Content Management System (CMS) called eXtended Object Oriented P ortal System (XOOPS). Due to the Open Source Status of the XOOPS CMS, programs d eveloped with this framework can be further customized to satisfy the demands of the user. To introduce the use of this framework, this paper exams three differ ent types of mechanical design and analysis problems. First, a repetitive design consideration and calculation process is transferred into WMADF programs to gai n efficiency for wired collaborative team. Second, the considered product solid model is created directly through the use of XOOPS program and Microsoft Compone nt Object Model (COM) instances. To the end of the paper, an example linked with ANSYS is used to indicate the possible application of this framework.展开更多
In order to examine the biaxial compression-compression properties of rubber fibre reinforced concrete(RFRC),an experimental study on RFRC under different lateral compressive stresses was carried out by considering di...In order to examine the biaxial compression-compression properties of rubber fibre reinforced concrete(RFRC),an experimental study on RFRC under different lateral compressive stresses was carried out by considering different rubber replacement rates and polypropylene fibre contents.The failure modes and mechanical property parameters of different RFRC working conditions were obtained from the experiment to explore the effects of rubber replacement rate and polypropylene fibre content on the biaxial compression-compression properties of RFRC.The following conclusions were drawn.Under the influence of lateral compressive stress,the biaxial compression-compression failure mode gradually developed from a columnar pattern to a flaky pattern,suggesting that the incorporation of rubber and polypropylene fibres into the concrete resulted in a significant change in the development of cracks.For different rubber replacement rates and polypropylene fibre contents,the vertical compressive stress exhibited the same developing trend under the influence of lateral compressive stress.Specifically,the lateral compressive stress imposed the minimum effect on the vertical compressive stress when the rubber replacement rate and polypropylene fibre content were 20%and 0.4%,respectively,and imposed the maximum effect when the rubber replacement rate and polypropylene fibre content were 20%and 0%,respectively.With the increase of rubber replacement rate,the vertical peak stress was significantly reduced,which implies that an appropriate amount of polypropylene fibres can increase the vertical peak stress to a certain extent.Then,the biaxial compression-compression mechanism of RFRC was analysed from the microscopic level by using scanning electron microscope(SEM).Meanwhile,based on Kupfer’s biaxial compression-compression failure criterion and the octahedral stress space,a biaxial compression-compression failure criterion for RFRC was proposed,which was proven to have good applicability.The research results of this study provide important theoretical basis for the engineering application and development of RFRC.展开更多
The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investiga...The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.展开更多
We used the finite element method (FEM) to investigate the stress profiles of vertebrae in patients who underwent balloon kyphoplasty (BKP) for vertebral fracture. BKP is often performed for persistent pain after vert...We used the finite element method (FEM) to investigate the stress profiles of vertebrae in patients who underwent balloon kyphoplasty (BKP) for vertebral fracture. BKP is often performed for persistent pain after vertebral fractures. However, fractures are frequently reported in the adjacent vertebrae after BKP. The purpose was to clarify the mechanism of fractures that occur in the adjacent vertebrae after BKP. The subjects were two patients (first case: 74-year-old woman;second case: 88-year-old woman) who had BKP for osteoporotic vertebral fractures (L1). A bone analysis software program, Mechanical Finder, was used to construct three-dimensional finite element models (T11-L3) from computed tomographic (CT) digital imaging and communications in medicine (DICOM) data. Moment loadings were examined to evaluate stress concentrations on the vertebrae. Young’s moduli were lower in the second case than in the first case at all vertebral levels. Maximum Drucker-Prager stresses after BKP were larger in the second case than in the first case for compression, flexion, extension, and axial rotation. Strain energy density decreased in L1 and increased in the adjacent ver-tebrae. Our results suggest that post-BKP fractures of the adjacent vertebrae not only are due to bone fragility, but also can be caused by increased rigidity in the vertebrae filled with bone cement, which increases stress concentration on the adjacent verte-brae and raises the likelihood of fracture.展开更多
This paper presents an alternate graphical procedure (Method 2), to that presented in earlier publications entitled, “A Procedure for Trisecting an Acute Angle” and “A Key to Solving the Angle Trisection Problem”....This paper presents an alternate graphical procedure (Method 2), to that presented in earlier publications entitled, “A Procedure for Trisecting an Acute Angle” and “A Key to Solving the Angle Trisection Problem”. The procedure, when applied to the 30˚ and 60˚ angles that have been “proven” to be nottrisectable and the 45˚ benchmark angle that is known to be trisectable, in each case produced a construction having an identical angular relationship with Archimedes’ Construction, as in Section 2 on THEORY of this paper, where the required trisection angle was found to be one-third of its respective angle (i.e. DE’MA = 1/3 DE’CG). For example, the trisection angle for the 30˚, 45˚ and 60˚ angles were 10.00000˚, 15.00000˚, and 20.00000˚, respectively, and Section 5 on PROOF in this paper. Therefore, based on this identical angular relationship and the numerical results (i.e. to five decimal places), which represent the highest degree of accuracy and precision attainable by The Geometer’s Sketch Pad software, one can only conclude that not only the geometric requirements for arriving at an exact trisection of the 30˚ and 60˚ angle (which have been “proven” to be not-trisectable) have been met, but also, the construction is valid for any arbitrary acute angle, despite theoretical proofs to the contrary by Wantzel, Dudley, and others.展开更多
In addition to being used for pattern transfer,the negative photoresist SU-8 iswidely used as a structural material in microelectromechanical systems(MEMS).Due to its good photopatternability,SU-8 has lower manufactur...In addition to being used for pattern transfer,the negative photoresist SU-8 iswidely used as a structural material in microelectromechanical systems(MEMS).Due to its good photopatternability,SU-8 has lower manufacturing costs than many other materials,but its mechanical properties are relatively weak to some extent,which limits its performance.The mechanical properties of epoxy-like SU-8 can be enhanced by addingmicro-or nano-fillers such as carbon nanotube,clay,and SiC nanowire,which have superior elastic modulus.In this study,SiC nanowires were used to improve the mechanical properties of SU-8 while the SU-8 retains its photopatternability.The SiC nanowires were uniformly dispersed in SU-8 by stirring and ultrasonication.SU-8 materials with different SiC nanowire contents were fabricated into dog bone samples by lithography.The elastic modulus,storage modulus,and damping factor of the samples were measured by the Dynamic mechanical analysis(DMA)Q800.The experiment result shows that the rigidity and toughness increased,and the damping reduced.The 2 wt%SiC nanowires-reinforced SU-8 had a 73.88%increase in elastic modulus and a 103.4%increase in elongation at break.Furthermore,a spring component made by SiC-doped SU-8 could withstand greater acceleration.The SiC nanowires-reinforced SU-8 has the potential tomeet higher requirements in the design andmanufacture of MEMS and greatly reduce the manufacturing costs of MEMS devices.展开更多
The crystallization behavior,crystal morphology and form,and viscoelastic behavior of poly(butylene succinate)(PBS)and coir fiber/PBS composites(CPB)were investigated by differential scanning calorimetry(DSC),polarize...The crystallization behavior,crystal morphology and form,and viscoelastic behavior of poly(butylene succinate)(PBS)and coir fiber/PBS composites(CPB)were investigated by differential scanning calorimetry(DSC),polarized optical microscopy(POM),X-ray diffraction(XRD)and dynamic mechanical analysis(DMA).The results of DSC measurement show that the crystallization temperature increases with the filling of coir fibers.POM images reveal that the spherulitic size and crystallization behavior of PBS are influenced by the coir fibers in the composites.XRD curves show that the crystal form of pure PBS and CPB are remaining almost identical.In addition,the storage modulus of CPB significantly increases comparing with the pure PBS.This predicted the dimensional stability and improved load-deformation temperature.In conclusion,the addition of coir fibers has a significant effect on the thermal properties of the matrix.展开更多
In order to effectively cope with exponent increase of the complexity faced to the rock mechanics analysis problems and the large incompatibility existing between the information level required to model the rock mass ...In order to effectively cope with exponent increase of the complexity faced to the rock mechanics analysis problems and the large incompatibility existing between the information level required to model the rock mass and engineering and our obtainable information level at hand,the integrated approaches with intelligent characters are proposed. Many previous standard methods,such as precedent type analysis,rock classification,analytic method stress-based,basic numerical methods (BEM,FEM,DEM,hybrid),and their extended numerical methods (fully coupled) to be developed,can be selected respectively or integrated accordingly. It is alternative to develop basic/fully integrated system,and internet-based approaches. These novel methods can also be selected or integrated each other or with the standard methods to perform rock mechanics analysis. Some key techniques to develop these alternative methods are discussed. It may focus in future on developing fully integrated systems and internet-based approaches. Developing an environmental,virtual facility/space shall be firstly done for this collaborative research on internet.展开更多
Low-basis-weight paper lacks normal strength and stiffness. Waterborne epoxy resin could be employed with oxidized starch to improve paper stiffness through surface sizing. In this study,the mechanism of enhancing sti...Low-basis-weight paper lacks normal strength and stiffness. Waterborne epoxy resin could be employed with oxidized starch to improve paper stiffness through surface sizing. In this study,the mechanism of enhancing stiffness by adding waterborne epoxy resin was fully investigated. The results indicated that through surface sizing with epoxy resin,the paper thickness was preserved,whereas the elastic modulus increased significantly and the epoxy resin had positive impact on single fiber strength. A rigid resin layer and interpenetrating polymer network formed on the surface and in the inner layer of the paper,respectively. The formed resin layer and interpenetrating polymer network strongly supported the paper,leading to the improvement of the elastic modulus and stiffness. The stiffness improvement through surface sizing was mainly due to the formation of a fibrous composite layer and penetration of the sizing agent into the inner layers of the paper. The better the combination between fiber and sizing agent,the higher were the elastic modulus and the stiffness of the whole paper.展开更多
We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis(DMTA) method. The experimental results show that the dynamic mechanica...We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis(DMTA) method. The experimental results show that the dynamic mechanical properties of cement asphalt pastes are sensitive to temperature due to the inclusion of asphalt, and may go through different states within a temperature range of-40 ℃ to 60 ℃, which is different from that of pure cement and asphalt. As the temperature of the cement asphalt paste increases, a considerable change of dynamic mechanical properties, including storage modulus(E'), loss modulus(E'') and loss factor(tand) is observed. Moreover, the influence of asphalt to cement(A/C) ratio on the temperature sensitivity of the dynamic mechanical properties of cement asphalt composites was investigated. The temperature dependency of cement asphalt composites is ascribed to the temperature dependency of the asphalt and its interaction with cement paste. A simple fractional model is proposed to describe the viscoelastic behavior of cement asphalt composites.展开更多
Revealing the relations among robotic comprehensive performance,configuration,scales and working tasks is the basis to optimize robotic mechanism. Due to the correlation and diversity of the single performance indexes...Revealing the relations among robotic comprehensive performance,configuration,scales and working tasks is the basis to optimize robotic mechanism. Due to the correlation and diversity of the single performance indexes,statistical principles of linear dimension reduction and nonlinear dimension reduction are introduced into comprehensive performance analysis and evaluation for typical serial robot. The robotic mechanism's configuration,scales and task with the best comprehensive performance can be obtained by principal component analysis( PCA) and kernel principal component analysis( KPCA) respectively. The results show that KPCA can reveal the nonlinear relations among different single performance indexes more effectively and provide more comprehensive performance information than PCA. Thus,task-oriented method of serial robot for mechanism analysis and evaluation is proposed,which also provides scientific research basis for the mechanism synthesis and optimum task order.展开更多
RegCM4.3, a high-resolution regional climate model, which includes five kinds of aerosols(dust, sea salt,sulfate, black carbon and organic carbon), is employed to simulate the East Asian summer monsoon(EASM) from 1995...RegCM4.3, a high-resolution regional climate model, which includes five kinds of aerosols(dust, sea salt,sulfate, black carbon and organic carbon), is employed to simulate the East Asian summer monsoon(EASM) from 1995 to 2010 and the simulation data are used to study the possible impact of natural and anthropogenic aerosols on EASM.The results show that the regional climate model can well simulate the EASM and the spatial and temporal distribution of aerosols. The EASM index is reduced by about 5% by the natural and anthropogenic aerosols and the monsoon onset time is also delayed by about a pentad except for Southeast China. The aerosols heat the middle atmosphere through absorbing solar radiation and the air column expands in Southeast China and its offshore areas. As a result, the geopotential height decreases and a cyclonic circulation anomaly is generated in the lower atmosphere. Northerly wind located in the west of cyclonic circulation weakens the low-level southerly wind in the EASM region. Negative surface radiative forcing due to aerosols causes downward motion and an indirect meridional circulation is formed with the low-level northerly wind and high-level southerly wind anomaly in the north of 25° N in the monsoon area, which weakens the vertical circulation of EASM. The summer precipitation of the monsoon region is significantly reduced,especially in North and Southwest China where the value of moisture flux divergence increases.展开更多
This research focused on the dynamic mechanical and thermal properties of woven mat jute/kenaf/jute(J/K/J)and kenaf/jute/kenaf(K/J/K)hybrid composites.Dynamic mechanical analysis(DMA)and Thermo-gravimetric Analysis(TG...This research focused on the dynamic mechanical and thermal properties of woven mat jute/kenaf/jute(J/K/J)and kenaf/jute/kenaf(K/J/K)hybrid composites.Dynamic mechanical analysis(DMA)and Thermo-gravimetric Analysis(TGA)were used to study the effect of layering sequence on the thermal properties of kenaf/jute hybrid composites.The DMA results;it was found that the differences in the stacking sequence between the kenaf/jute composites do not affect their storage modulus,loss modulus and damping factor.From the TGA and DMA results,it has been shown that stacking sequence has given positive effect to the kenaf/jute hybrid composite compared to pure epoxy composite.This is because kenaf and jute fibre has increased the Tg values of the composites,thus affect the thermal degradation.Results showed that the storage modulus for kenaf/jute hybrid composites increased compared with pure epoxy composites with increasing temperature and the values of remained almost the same at glass transition temperature(Tg),the hybrid composite perhaps due to the improved fibre/matrix interface bonding.The preliminary analysis could provide a new direction for the creation of a novel hybrid composite which offers unique properties which cannot be accomplished in a single material system.展开更多
With the development of space science and technology,the on-orbit servicing technologies of spacecraft get more and more attention.According to the design criterion of existing spacecraft in orbit module replacement t...With the development of space science and technology,the on-orbit servicing technologies of spacecraft get more and more attention.According to the design criterion of existing spacecraft in orbit module replacement technology,the flexible swap device is designed and the dynamics simulation of institutions by the automatic dynamic analysis of mechanical systems(ADAMS)simulation software is analyzed.Throughout the analysis process,this paper studies the effect of collision force of flexible mechanism and provides a basis for the optimization of flexible plug agencies.展开更多
文摘Conventionally available Polyvinyl acetate (PVAc) wood glues are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor strength at high humidity, poor strength at high temperature and workability at low-temperature. PVAc is non-resistant to high humidity, and if such adhesive bonds are exploited in a highly humid environment, its strength substantially decreases. Sufficiently water-resistant adhesive bonds are achieved by modifying PVAc dispersion with special chemicals like acrylic acid (AA) and N-methylol acrylamide (NMA) as a co-monomer, Silanes, and ethylene modified PVA. The Lewis acids like aluminium chloride and aluminium nitrate are used as cross-linkers. So PVAc adhesives are classified as reactive and non-reactive glue. Application of non-reactive D1 (as per EN 204-205) and reactive D2 and D3 (as per EN 204-205) adhesives for bonding laminate on plywood is a regular practice in the Indian market. In summer time, Crack formation was seen in laminate bonded with reactive D2 and D3 adhesives in regions where the room temperature was above 45°C. However, if the same laminate substrates were bonded with non-reactive D1, no cracks were seen. To analyse the above phenomenon, we have done Dynamic mechanical analysis of non-reactive D1, reactive D2 and D3 adhesive.
基金the Natural Science Foundation of Jiangsu Province of China(Grant No.BK20200999),meanwhile I am also grateful to Prof.Renshu Yuan for his help.
文摘To improve the bearing pressure capacity of ultrahigh pressure apparatus,the internal autofrettaged cylinder with interlayer pressure(ACCIP)is introduced,and the analytical model for the ACCIP structure and its derivation are presented as well.Calculation showed that the ACCIP method enhance bearing pressure of the apparatus obviously;optimization results revealed that under the working pressure pw=1.07σs and different radius ratios,the ACCIP method can keep the apparatus in deformed-elastically state;And when the pw=1.07σs,the minimum radius ratio was approximate 3.29,in this case,no yielding happened.The above results demonstrate that the ACCIP method is a promising technique to improve the bearing pressure of ultrahigh pressure apparatus,and the analytical model for the ACCIP method is also reasonable.In addition,the minimum radius ratio ro/ri under randomly specified workload can be Fig.d out by the analytical model proposed in this work.
基金National Key Basic Research Program of China(No.2014CB046303)。
文摘The mechanical state of cantilever gearbox housing is different from ordinary ones due to the long arm of force caused by cantilever structure.Conventional mechanical analysis methods either took cantilever gearbox housing as ordinary ones or cantilever beam.Few published papers have specially focused on mechanical analysis method for cantilever gearbox housing.This paper takes a longwall shearer cutting unit gearbox(SCUG)as an example and the mechanical analysis method is investigated according to the causes of fatigue for SCUG.Force analysis model is established for finding out regions of static fatigue caused by low-frequency loads,and local resonance analysis is used for finding out regions of vibration fatigue caused by high-frequency loads.Not only bending moment but also torque caused by gear meshing forces is taken into account in the force analysis model.Vibration response is obtained from cutting experiment,and dominant frequencies of local resonance are obtained by frequency domain analysis.Finite element model of SCUG is established,and natural frequencies and strain modes are analyzed for obtaining the main vibration modes corresponding to dominant frequencies.Hence,large stress regions caused by low and high frequency loads are obtained.Results show that the worst working condition is oblique cutting,and the stress of B-B in 600 mm cutting depth can reach 166 MPa.Obviously,950 Hz,1250 Hz,and 1400 Hz are dominant frequencies of SCUG(23rd,25th and 27th natural frequencies).Generally,this paper proposes some principles for mechanical analysis method of cantilever gearbox housing.
文摘Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) and sized short-glass fibres with two amino-silane coupling agents.The calcite particle content is 0, 11.7 and 23.5 vol. pct for the matrices. The glass fiber contentis 0, 10 and 15 vol. pct. The matrix materials and corresponding composites were compoundedusing a twin screw extruder and dumbbell-shaped tensile bars were prepared with an injectionmolding process. The tensile and flexural properties as well as the unnotched and notchedCharpy impact energies of short glass fibre/calcite/ABS composites were studied in this paper.The effects of fibres, fibre surface treatments and particles on these mechanical properties ofthe composites were discussed in detail. An importarit information was obtained, which is thatthe tensile and flexural strengths of hybrid SGF/calcite/ABS composites are the same as thoseof corresponding fibre composites when the ratio of the interfacial adhesion strength betweenparticles and matrix to that between fibres and matrix is higher than certain value. otherwise theformer are lower than the latter.
基金supported by grants from NIH (P30GM103333 and RO1AR054385 to LW)China CSC fellowship (to LF)DOD W81XWH-13-1-0148 (to XLL)
文摘The transport of fluid, nutrients, and signaling molecules in the bone lacunar–canalicular system(LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching(FRAP) approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30–50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis(FEA)approach. An intact murine tibia was first re-constructed from micro CT images into a three-dimensional(3D)linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform(FEBio) to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex.Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces(shear and drag forces) for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.
文摘In this paper, a Web-based Mechanical Design and A na lysis Framework (WMDAF) is proposed. This WMADF allows designers to develop web -based computer aided programs in a systematic way during the collaborative mec hanical system design and analysis process. This system is based on an emerg ing web-based Content Management System (CMS) called eXtended Object Oriented P ortal System (XOOPS). Due to the Open Source Status of the XOOPS CMS, programs d eveloped with this framework can be further customized to satisfy the demands of the user. To introduce the use of this framework, this paper exams three differ ent types of mechanical design and analysis problems. First, a repetitive design consideration and calculation process is transferred into WMADF programs to gai n efficiency for wired collaborative team. Second, the considered product solid model is created directly through the use of XOOPS program and Microsoft Compone nt Object Model (COM) instances. To the end of the paper, an example linked with ANSYS is used to indicate the possible application of this framework.
基金supported by the National 12th Five Year Plan of Science and Technology Support Project(2015 BAL02b02)National Spark Plan Project(2015 GA690045),Jiangsu Province“Six Talent Peaks”Team Project(XCL-CXTD−007).
文摘In order to examine the biaxial compression-compression properties of rubber fibre reinforced concrete(RFRC),an experimental study on RFRC under different lateral compressive stresses was carried out by considering different rubber replacement rates and polypropylene fibre contents.The failure modes and mechanical property parameters of different RFRC working conditions were obtained from the experiment to explore the effects of rubber replacement rate and polypropylene fibre content on the biaxial compression-compression properties of RFRC.The following conclusions were drawn.Under the influence of lateral compressive stress,the biaxial compression-compression failure mode gradually developed from a columnar pattern to a flaky pattern,suggesting that the incorporation of rubber and polypropylene fibres into the concrete resulted in a significant change in the development of cracks.For different rubber replacement rates and polypropylene fibre contents,the vertical compressive stress exhibited the same developing trend under the influence of lateral compressive stress.Specifically,the lateral compressive stress imposed the minimum effect on the vertical compressive stress when the rubber replacement rate and polypropylene fibre content were 20%and 0.4%,respectively,and imposed the maximum effect when the rubber replacement rate and polypropylene fibre content were 20%and 0%,respectively.With the increase of rubber replacement rate,the vertical peak stress was significantly reduced,which implies that an appropriate amount of polypropylene fibres can increase the vertical peak stress to a certain extent.Then,the biaxial compression-compression mechanism of RFRC was analysed from the microscopic level by using scanning electron microscope(SEM).Meanwhile,based on Kupfer’s biaxial compression-compression failure criterion and the octahedral stress space,a biaxial compression-compression failure criterion for RFRC was proposed,which was proven to have good applicability.The research results of this study provide important theoretical basis for the engineering application and development of RFRC.
基金supported by CNPC Key Core Technology Research Projects (2022ZG06)project funded by China Postdoctoral Science Foundation (2021M693508)Basic research and strategic reserve technology research fund project of institutes directly under CNPC.
文摘The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.
文摘We used the finite element method (FEM) to investigate the stress profiles of vertebrae in patients who underwent balloon kyphoplasty (BKP) for vertebral fracture. BKP is often performed for persistent pain after vertebral fractures. However, fractures are frequently reported in the adjacent vertebrae after BKP. The purpose was to clarify the mechanism of fractures that occur in the adjacent vertebrae after BKP. The subjects were two patients (first case: 74-year-old woman;second case: 88-year-old woman) who had BKP for osteoporotic vertebral fractures (L1). A bone analysis software program, Mechanical Finder, was used to construct three-dimensional finite element models (T11-L3) from computed tomographic (CT) digital imaging and communications in medicine (DICOM) data. Moment loadings were examined to evaluate stress concentrations on the vertebrae. Young’s moduli were lower in the second case than in the first case at all vertebral levels. Maximum Drucker-Prager stresses after BKP were larger in the second case than in the first case for compression, flexion, extension, and axial rotation. Strain energy density decreased in L1 and increased in the adjacent ver-tebrae. Our results suggest that post-BKP fractures of the adjacent vertebrae not only are due to bone fragility, but also can be caused by increased rigidity in the vertebrae filled with bone cement, which increases stress concentration on the adjacent verte-brae and raises the likelihood of fracture.
文摘This paper presents an alternate graphical procedure (Method 2), to that presented in earlier publications entitled, “A Procedure for Trisecting an Acute Angle” and “A Key to Solving the Angle Trisection Problem”. The procedure, when applied to the 30˚ and 60˚ angles that have been “proven” to be nottrisectable and the 45˚ benchmark angle that is known to be trisectable, in each case produced a construction having an identical angular relationship with Archimedes’ Construction, as in Section 2 on THEORY of this paper, where the required trisection angle was found to be one-third of its respective angle (i.e. DE’MA = 1/3 DE’CG). For example, the trisection angle for the 30˚, 45˚ and 60˚ angles were 10.00000˚, 15.00000˚, and 20.00000˚, respectively, and Section 5 on PROOF in this paper. Therefore, based on this identical angular relationship and the numerical results (i.e. to five decimal places), which represent the highest degree of accuracy and precision attainable by The Geometer’s Sketch Pad software, one can only conclude that not only the geometric requirements for arriving at an exact trisection of the 30˚ and 60˚ angle (which have been “proven” to be not-trisectable) have been met, but also, the construction is valid for any arbitrary acute angle, despite theoretical proofs to the contrary by Wantzel, Dudley, and others.
基金supports from the Shanghai Professional Technical Service Platform for Non-Silicon Micro-Nano Integrated ManufacturingProject funded by China Postdoctoral Science Foundation (No. 2018M630440)
文摘In addition to being used for pattern transfer,the negative photoresist SU-8 iswidely used as a structural material in microelectromechanical systems(MEMS).Due to its good photopatternability,SU-8 has lower manufacturing costs than many other materials,but its mechanical properties are relatively weak to some extent,which limits its performance.The mechanical properties of epoxy-like SU-8 can be enhanced by addingmicro-or nano-fillers such as carbon nanotube,clay,and SiC nanowire,which have superior elastic modulus.In this study,SiC nanowires were used to improve the mechanical properties of SU-8 while the SU-8 retains its photopatternability.The SiC nanowires were uniformly dispersed in SU-8 by stirring and ultrasonication.SU-8 materials with different SiC nanowire contents were fabricated into dog bone samples by lithography.The elastic modulus,storage modulus,and damping factor of the samples were measured by the Dynamic mechanical analysis(DMA)Q800.The experiment result shows that the rigidity and toughness increased,and the damping reduced.The 2 wt%SiC nanowires-reinforced SU-8 had a 73.88%increase in elastic modulus and a 103.4%increase in elongation at break.Furthermore,a spring component made by SiC-doped SU-8 could withstand greater acceleration.The SiC nanowires-reinforced SU-8 has the potential tomeet higher requirements in the design andmanufacture of MEMS and greatly reduce the manufacturing costs of MEMS devices.
基金The Natural Science Foundation of Shandong Province,China(Grant No.ZR2020QE075).
文摘The crystallization behavior,crystal morphology and form,and viscoelastic behavior of poly(butylene succinate)(PBS)and coir fiber/PBS composites(CPB)were investigated by differential scanning calorimetry(DSC),polarized optical microscopy(POM),X-ray diffraction(XRD)and dynamic mechanical analysis(DMA).The results of DSC measurement show that the crystallization temperature increases with the filling of coir fibers.POM images reveal that the spherulitic size and crystallization behavior of PBS are influenced by the coir fibers in the composites.XRD curves show that the crystal form of pure PBS and CPB are remaining almost identical.In addition,the storage modulus of CPB significantly increases comparing with the pure PBS.This predicted the dimensional stability and improved load-deformation temperature.In conclusion,the addition of coir fibers has a significant effect on the thermal properties of the matrix.
基金Nature Science Foundation of China under Grant no.50179034.
文摘In order to effectively cope with exponent increase of the complexity faced to the rock mechanics analysis problems and the large incompatibility existing between the information level required to model the rock mass and engineering and our obtainable information level at hand,the integrated approaches with intelligent characters are proposed. Many previous standard methods,such as precedent type analysis,rock classification,analytic method stress-based,basic numerical methods (BEM,FEM,DEM,hybrid),and their extended numerical methods (fully coupled) to be developed,can be selected respectively or integrated accordingly. It is alternative to develop basic/fully integrated system,and internet-based approaches. These novel methods can also be selected or integrated each other or with the standard methods to perform rock mechanics analysis. Some key techniques to develop these alternative methods are discussed. It may focus in future on developing fully integrated systems and internet-based approaches. Developing an environmental,virtual facility/space shall be firstly done for this collaborative research on internet.
基金financially supported by the National Natural Science Funds of China(grant number31470599)the Priority Academic Program Development of Jiangsu Higher Education Institutions,China
文摘Low-basis-weight paper lacks normal strength and stiffness. Waterborne epoxy resin could be employed with oxidized starch to improve paper stiffness through surface sizing. In this study,the mechanism of enhancing stiffness by adding waterborne epoxy resin was fully investigated. The results indicated that through surface sizing with epoxy resin,the paper thickness was preserved,whereas the elastic modulus increased significantly and the epoxy resin had positive impact on single fiber strength. A rigid resin layer and interpenetrating polymer network formed on the surface and in the inner layer of the paper,respectively. The formed resin layer and interpenetrating polymer network strongly supported the paper,leading to the improvement of the elastic modulus and stiffness. The stiffness improvement through surface sizing was mainly due to the formation of a fibrous composite layer and penetration of the sizing agent into the inner layers of the paper. The better the combination between fiber and sizing agent,the higher were the elastic modulus and the stiffness of the whole paper.
基金Funded by the National Natural Science Foundation of China(50878209 and 51208515)the National Basic Research Program of China(“973”Program)(2013CB036201)
文摘We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis(DMTA) method. The experimental results show that the dynamic mechanical properties of cement asphalt pastes are sensitive to temperature due to the inclusion of asphalt, and may go through different states within a temperature range of-40 ℃ to 60 ℃, which is different from that of pure cement and asphalt. As the temperature of the cement asphalt paste increases, a considerable change of dynamic mechanical properties, including storage modulus(E'), loss modulus(E'') and loss factor(tand) is observed. Moreover, the influence of asphalt to cement(A/C) ratio on the temperature sensitivity of the dynamic mechanical properties of cement asphalt composites was investigated. The temperature dependency of cement asphalt composites is ascribed to the temperature dependency of the asphalt and its interaction with cement paste. A simple fractional model is proposed to describe the viscoelastic behavior of cement asphalt composites.
基金Sponsored by the National Natural Science Foundation of China(Grant No.51075005)the Beijing City Science and Technology Project(Grant No.Z131100005313009)
文摘Revealing the relations among robotic comprehensive performance,configuration,scales and working tasks is the basis to optimize robotic mechanism. Due to the correlation and diversity of the single performance indexes,statistical principles of linear dimension reduction and nonlinear dimension reduction are introduced into comprehensive performance analysis and evaluation for typical serial robot. The robotic mechanism's configuration,scales and task with the best comprehensive performance can be obtained by principal component analysis( PCA) and kernel principal component analysis( KPCA) respectively. The results show that KPCA can reveal the nonlinear relations among different single performance indexes more effectively and provide more comprehensive performance information than PCA. Thus,task-oriented method of serial robot for mechanism analysis and evaluation is proposed,which also provides scientific research basis for the mechanism synthesis and optimum task order.
基金National Key Project of Ministry of Science and Technology of China(2016YFC0203301)National Key Basic Research and Development Project of China(2015CB453201,2013CB430103)+1 种基金National Natural Science Foundation of China(41375058,41530427)Jiangsu Natural Science Key Project of China(BK20150062)
文摘RegCM4.3, a high-resolution regional climate model, which includes five kinds of aerosols(dust, sea salt,sulfate, black carbon and organic carbon), is employed to simulate the East Asian summer monsoon(EASM) from 1995 to 2010 and the simulation data are used to study the possible impact of natural and anthropogenic aerosols on EASM.The results show that the regional climate model can well simulate the EASM and the spatial and temporal distribution of aerosols. The EASM index is reduced by about 5% by the natural and anthropogenic aerosols and the monsoon onset time is also delayed by about a pentad except for Southeast China. The aerosols heat the middle atmosphere through absorbing solar radiation and the air column expands in Southeast China and its offshore areas. As a result, the geopotential height decreases and a cyclonic circulation anomaly is generated in the lower atmosphere. Northerly wind located in the west of cyclonic circulation weakens the low-level southerly wind in the EASM region. Negative surface radiative forcing due to aerosols causes downward motion and an indirect meridional circulation is formed with the low-level northerly wind and high-level southerly wind anomaly in the north of 25° N in the monsoon area, which weakens the vertical circulation of EASM. The summer precipitation of the monsoon region is significantly reduced,especially in North and Southwest China where the value of moisture flux divergence increases.
基金This work is supported by UPM under GP-IPS Grant 9486400.
文摘This research focused on the dynamic mechanical and thermal properties of woven mat jute/kenaf/jute(J/K/J)and kenaf/jute/kenaf(K/J/K)hybrid composites.Dynamic mechanical analysis(DMA)and Thermo-gravimetric Analysis(TGA)were used to study the effect of layering sequence on the thermal properties of kenaf/jute hybrid composites.The DMA results;it was found that the differences in the stacking sequence between the kenaf/jute composites do not affect their storage modulus,loss modulus and damping factor.From the TGA and DMA results,it has been shown that stacking sequence has given positive effect to the kenaf/jute hybrid composite compared to pure epoxy composite.This is because kenaf and jute fibre has increased the Tg values of the composites,thus affect the thermal degradation.Results showed that the storage modulus for kenaf/jute hybrid composites increased compared with pure epoxy composites with increasing temperature and the values of remained almost the same at glass transition temperature(Tg),the hybrid composite perhaps due to the improved fibre/matrix interface bonding.The preliminary analysis could provide a new direction for the creation of a novel hybrid composite which offers unique properties which cannot be accomplished in a single material system.
文摘With the development of space science and technology,the on-orbit servicing technologies of spacecraft get more and more attention.According to the design criterion of existing spacecraft in orbit module replacement technology,the flexible swap device is designed and the dynamics simulation of institutions by the automatic dynamic analysis of mechanical systems(ADAMS)simulation software is analyzed.Throughout the analysis process,this paper studies the effect of collision force of flexible mechanism and provides a basis for the optimization of flexible plug agencies.
