The correlation between the initial time value of transient iterative parameters and the blowing pressure in the numerical simulation process of blowing balloon is investigated by POLYFLOW. The results show that: 1) A...The correlation between the initial time value of transient iterative parameters and the blowing pressure in the numerical simulation process of blowing balloon is investigated by POLYFLOW. The results show that: 1) As the blow molding pressure increases, the boundary value of the iterative time step decreases rapidly at first and then slowly. At the end of the first step of iterative calculation for each boundary value, the balloon parison is in the mold core cavity. 2) If the initial time value of transient iterative parameters is smaller than the boundary value of the iterative time step, the balloon parison is still in the mold core cavity at the end of the first iteration. However, if the iterative calculation continues, the calculation process may be interrupted when the time step is smaller than the initial time value of the transient iterative parameters, which makes the blow molding simulation of balloon unable to continue. 3) It is suggested that the initial time value of transient iterative parameters is one order of magnitude smaller than the boundary value of the iterative time step to complete smoothly the simulation of blow molding balloon.展开更多
A surface micro-/nano-structured metal plate can be joined with an injection molded plastic piece in a mold,which has been named injection molded direct joining(IMDJ).The injected plastic melt infiltrates the micro-/n...A surface micro-/nano-structured metal plate can be joined with an injection molded plastic piece in a mold,which has been named injection molded direct joining(IMDJ).The injected plastic melt infiltrates the micro-/nano-structure,e.g.,a porous structure with micro/nano pores,on the metal plate while flowing in the mold cavity where the metal plate is inserted.After solidification of the plastic,the metal and plastic materials are directly joined via the micro-/nano-structured metal surface.Since air is trapped by the plastic melt,it is easily imagined that the air in the mold cavity prevents the melt plastic from contacting the metal surface and infiltrating the micro-/nano-structure,which could result in poorer joining performance.To avoid the prevention of the air for the better joining performance,the present study proposes a system actively venting the mold cavity during injection molding.To apply the active venting to IMDJ,venting and sealing systems were newly developed.In addition,a system measuring air pressure of the mold cavity was developed.The proposed system was evaluated by a measurement of joining strengths of IMDJ specimens that were produced under various conditions.From the results,it is concluded that the active venting does not necessarily have a positive effect in any cases:the effect depends on the type of surface micro-/nano-structure.展开更多
文摘The correlation between the initial time value of transient iterative parameters and the blowing pressure in the numerical simulation process of blowing balloon is investigated by POLYFLOW. The results show that: 1) As the blow molding pressure increases, the boundary value of the iterative time step decreases rapidly at first and then slowly. At the end of the first step of iterative calculation for each boundary value, the balloon parison is in the mold core cavity. 2) If the initial time value of transient iterative parameters is smaller than the boundary value of the iterative time step, the balloon parison is still in the mold core cavity at the end of the first iteration. However, if the iterative calculation continues, the calculation process may be interrupted when the time step is smaller than the initial time value of the transient iterative parameters, which makes the blow molding simulation of balloon unable to continue. 3) It is suggested that the initial time value of transient iterative parameters is one order of magnitude smaller than the boundary value of the iterative time step to complete smoothly the simulation of blow molding balloon.
基金This study was supported by JSPS KAKENHI(#17J00345)and the Foundation for the Promotion of Industrial Science.A part of the experiments was carried out with the supports and advices of Yokoi group,the University of Tokyo,Japan.
文摘A surface micro-/nano-structured metal plate can be joined with an injection molded plastic piece in a mold,which has been named injection molded direct joining(IMDJ).The injected plastic melt infiltrates the micro-/nano-structure,e.g.,a porous structure with micro/nano pores,on the metal plate while flowing in the mold cavity where the metal plate is inserted.After solidification of the plastic,the metal and plastic materials are directly joined via the micro-/nano-structured metal surface.Since air is trapped by the plastic melt,it is easily imagined that the air in the mold cavity prevents the melt plastic from contacting the metal surface and infiltrating the micro-/nano-structure,which could result in poorer joining performance.To avoid the prevention of the air for the better joining performance,the present study proposes a system actively venting the mold cavity during injection molding.To apply the active venting to IMDJ,venting and sealing systems were newly developed.In addition,a system measuring air pressure of the mold cavity was developed.The proposed system was evaluated by a measurement of joining strengths of IMDJ specimens that were produced under various conditions.From the results,it is concluded that the active venting does not necessarily have a positive effect in any cases:the effect depends on the type of surface micro-/nano-structure.
