To explore the role of biofilm formation on the corrosion of marine concrete structures, we investigated the attachment of biofilm on mortar surfaces in simulated seawater and the influence of biofilm on the microstru...To explore the role of biofilm formation on the corrosion of marine concrete structures, we investigated the attachment of biofilm on mortar surfaces in simulated seawater and the influence of biofilm on the microstructure of mortar surfaces. The results show that the evolution of biofilm on mortar surfaces in simulated seawater is closely related to the corrosion suffered by the mortar, and the process of biofilm attachment and shedding is continuous and cyclical. It is found that the specimens in the absence of biofilm attachment are more severely eroded internally by the corrosive medium in simulated seawater than those in the presence of biofilm attachment. For the specimens without biofilm attachment, after 60 days, gypsum forms,and after 120 days, the number of pores in the mortar is reduced. In contrast, for the specimens in the presence of biofilm attachment, gypsum could only be detected after 90 days, and fewer pores are filled. Therefore, the formation of biofilm could delay the invasion of the corrosive medium into the interior of mortar during the evolution of biofilm on mortar surfaces, mitigating the corrosion of mortars in seawater.展开更多
In this paper,the durability of cement mortar prepared with a recycled-concrete fine powder(RFP)was examined;including the analysis of a variety of aspects,such as the carbonization,sulfate attack and chloride ion ero...In this paper,the durability of cement mortar prepared with a recycled-concrete fine powder(RFP)was examined;including the analysis of a variety of aspects,such as the carbonization,sulfate attack and chloride ion erosion resistance.The results indicate that the influence of RFP on these three aspects is different.The carbonization depth after 30 days and the chloride diffusion coefficient of mortar containing 10%RFP decreased by 13.3%and 28.19%.With a further increase in the RFP content,interconnected pores formed between the RFP particles,leading to an acceleration of the penetration rate of CO_(2)and Cl^(−).When the RFP content was less than 50%,the corrosion resistance coefficient of the compressive strength of the mortar was 0.84-1.05 after 90 days of sulfate attack.But the expansion and cracking of the mortar was effectively alleviated due to decrease of the gypsum production.Scanning electron microscope(SEM)analysis has confirmed that 10%RFP contributes to the formation of a dense microstructure in the cement mortar.展开更多
Purpose–During the construction process of the China Railway Track System(CRTS)I type filling layer,the nonwoven fabric bags have been used as grouting templates for cement asphalt(CA)emulsified mortar.The porous str...Purpose–During the construction process of the China Railway Track System(CRTS)I type filling layer,the nonwoven fabric bags have been used as grouting templates for cement asphalt(CA)emulsified mortar.The porous structure of nonwoven fabrics endowed the templates with breathability and water permeability.The standard requires that the volume expansion rate of CA mortar must be controlled within 1%–3%,which can generate expansion pressure to ensure that the cavities under track slabs are filled fully.However,the expansion pressure caused some of the water to seep out from the periphery of the filling bag,and it would affect the actual mix proportion of CA mortar.The differences in physical and mechanical properties between the CA mortar under track slabs and the CA mortar formed in the laboratory were studied in this paper.The relevant results could provide important methods for the research of filling layer materials for CRTS I type and other types of ballastless tracks in China.Design/methodology/approach–During the inspection of filling layer,the samples of CA mortar from different working conditions and raw materials were taken by uncovering the track slabs and drilling cores.The physical and mechanical properties of CA mortar under the filling layer of the slab were systematically analyzed by testing the electrical flux,compressive strength and density of mortar in different parts of the filling layer.Findings–In this paper,the electric flux,the physical properties and mechanical properties of different parts of CA mortar under the track slab were investigated.The results showed that the density,electric flux and compressive strength of CA mortar were affected by the composition of raw materials for dry powders and different parts of the filling layer.In addition,the electrical flux of CA mortar gradually decreased within 90 days’age.The electrical flux of samples with the thickness of 54 mm was lower than 500 C.Therefore,the impermeability and durability of CA mortar could be improved by increasing the thickness of filling layer.Besides,the results showed that the compressive strength of CA mortar increased,while the density and electric flux decreased gradually,with the prolongation of hardening time.Originality/value–During 90 days’age,the electrical flux of the CA mortar gradually decreased with the increase of specimen thickness and the electrical flux of the specimens with the thickness of 54 mm was lower than 500 C.The impermeability and durability of the CA mortar could be improved by increasing the thickness of filling layer.The proposed method can provide reference for the further development and improvement of CRTS I and CRTS II type ballastless track in China.展开更多
The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechani...The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.展开更多
In this paper, a compression-to-tension conversion technique is developed by applying predominant mode I loading test, using a servo-controlled compression system. The technique is applied to thin mortar plate specime...In this paper, a compression-to-tension conversion technique is developed by applying predominant mode I loading test, using a servo-controlled compression system. The technique is applied to thin mortar plate specimens of different widths that include a prefabricated crack on either a single side to facilitate unilateral crack propagation, or prefabricated cracks positioned on both sides asymmetrically with respect to the specimen midpoint to facilitate bilateral crack propagation under direct tensile stress with a loading rate of 0.001 mm/s. The results show that the main pathways of unilateral crack propagation governing specimen failure are fluctuated locally, but present an approximately straight line overall in the absence of pre-existing internal defects. However, the pathways of bilateral crack propagation are relatively complex, although they present similar characteristics. Analysis results suggest that bilateral crack propagation can be basically divided into three stages, i.e. a stage of linear propagation, a stage representing deviation from the other crack, and a stage where one crack approaches either the other crack or approaches the opposite edge of the specimen, and thereby forming a continuous crack through the specimen. In addition, the stressestrain curves of bilateral crack specimens do not vary significantly around the point of peak stress prior to specimen failure, which means that the specimens do not fail instantaneously.展开更多
We completed the uniaxial tensile test of mortar in the range of strain rate from 10^(-6)to 10^(-4)s^(-1)in the section containing softening,and carried out acoustic emission monitoring(AE)simultaneously.A series of A...We completed the uniaxial tensile test of mortar in the range of strain rate from 10^(-6)to 10^(-4)s^(-1)in the section containing softening,and carried out acoustic emission monitoring(AE)simultaneously.A series of AE parameters and spectrum analysis methods were used to identify the damage evolution process and cracking mechanism of mortar at different strain rates.The results show that,with the increase of strain rate,the peak stress and tensile elastic modulus of mortar increase obviously,and the stress level corresponding to the starting point of AE activity increases significantly as well,which indicates that the mechanical properties and AE characteristics of mortar have obvious strain rate effect.With the increase of strain rate,the cumulative AE hit decreases gradually,while the average AE hit rate increases significantly,indicating that the increase of strain rate reduces the damage degree of internal microstructure of the specimen,but the crack propagation speed increases.In the pre-peak stress stage,the average of AE ringing count and signal energy decreases with the increase of strain rate,while the average of duration increases;in the post-peak stress stage(f_(t)-30%f_(t)),the average of the three AE parameters all increase with the increase of strain rate,indicating that the strain rate effect on the damage process of mortar is different before and after peak stress,and the damage mechanism represented by different parameters is also different.In the whole process of uniaxial tensile of mortar,with the increase of strain rate,the scatter distribution of AE frequency-amplitude becomes more discrete,and the b-value shows a decreasing trend.In addition,the average level of AE peak frequency decreases with the increase of strain rate,while that of ca8 band wavelet energy spectrum coefficient increases.It is indicated that the increase of strain rate enables the crack propagation state of mortar specimen to become unstable,and the width of macrocrack increases but the proportion decreases.展开更多
Two different freeze-thaw cycles(FTC)are considered in this study to assess the related impact on gas permeability and micro-pore structure of a mortar.These are the water-freezing/water-thawing(WF-WT)and the air-free...Two different freeze-thaw cycles(FTC)are considered in this study to assess the related impact on gas permeability and micro-pore structure of a mortar.These are the water-freezing/water-thawing(WF-WT)and the air-freezing/air-thawing(AF-AT)cycles.The problem is addressed experimentally through an advanced nuclear magnetic resonance(NMR)technique able to provide meaningful information on the relationships among gas permeability,pore structure,mechanical properties,and the number of cycles.It is shown that the mortar gas permeability increases with the number of FTCs,the increase factor being 20 and 12.83 after 40 cycles for the WF-WT and AF-AT,respectively.The results also confirm that gas permeability hysteresis phenomena occur during the confining pressure loading and unloading process.展开更多
The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal con...The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal conductivity and hydration.The results showed that with the addition of 0.7%by weight of NFC per emulsion in the presence of a cationic surfactant(CTAB).The new material produced presented a dry porosity between 4.7%and 4.4%,compressive strength between 9.8 and 22.9 MPa,and thermal conductivity between 0.95 and 2.25 W·m^(−1)·K^(−1).Thus we show better mechanical and thermal performance than that traditional Portland cement mortar with a density similar.In addition,the mortar made by emulsion of ordinary portland cement,cellulose nanofiber and organophilic clay(OC)treated with cetyltrimethylammonium bromide(CTAB)obtained has good resistance under high temperature and water,as well as excellent thermal insulation performance under high temperature and humidity conditions.This study verified that the presence of NFC promotes hydration,leading to the production of more calcium silicate and portlandite gel.展开更多
This study deals with the analysis of the detrimental effects of a“sulfate attack”on cement mortar for different dry-wet cycles.The mass loss,tensile strength,and gas permeability coefficient were determined and ana...This study deals with the analysis of the detrimental effects of a“sulfate attack”on cement mortar for different dry-wet cycles.The mass loss,tensile strength,and gas permeability coefficient were determined and analyzed under different exposure conditions.At the same time,nitrogen adsorption(NAD),scanning electron microscopy(SEM),and X-ray diffraction(XRD)techniques were used to analyze the corresponding variations in the microstructure and the corrosion products.The results show that certain properties of the cement mortar evolve differently according to the durations of the dry-wet cycles and that some damage is caused to the mortars in aqueous solution.The pores fill with corrosion products,increasing the mortar specimen mass and tensile strength while reducing the permeability coefficient and pore size distribution.As corrosion proceeds,the crystallization pressure of the corrosion products increases,resulting in a 16%reduction in tensile strength from the initial value and a 2.6-factor increase in the permeability coefficient,indicating sensitivity to sulfate attack damage.Furthermore,the main corrosion products generated in the experiment are gypsum and ettringite.Application of osmotic pressure and extension of the immersion time can accelerate the erosion process.展开更多
This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Resul...This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Results indicate that there is a non-linear relationship between the corrosion degree of steel reinforcement in CAC mortar and the concentration of NaCl solution.The electrochemical parameters of specimens immersed in 3%NaCl solution suddenly drop at 40 days,earlier than 60 days of the reference.And the charge transfer resistivity of the specimen has decreased by 11 orders of magnitude at 40 days,showing an evident corrosion on steel reinforcement.However,it is interesting to notice that the corrosion is delayed by high external chloride concentration.The specimens immersed in 9%and 15%NaCl solutions remain in a relatively stable state within 120 days with slight pitting.The great corrosion protection of CAC concrete to embedded steel bars enables its wide application in marine.展开更多
Since masonry structures are prone to collapse in earthquakes,a novel joint reinforcement method with a polypropylene band(PP-band)and cement mortar(CM)has been put forward.Compared with the common reinforcement metho...Since masonry structures are prone to collapse in earthquakes,a novel joint reinforcement method with a polypropylene band(PP-band)and cement mortar(CM)has been put forward.Compared with the common reinforcement methods,this method not only facilitates construction but also ensures lower reinforcement cost.To systematically explore the influence of joint reinforcement on the seismic performance of masonry walls,quasi-static tests were carried out on six specimens with different reinforcement forms.The test results show that the joint action of PP-band and CM can significantly improve the specimen′s brittle failure characteristics and enhance the integrity of the specimen after cracking.Compared with the specimen without reinforcement,each of the seismic performance indexes of the joint reinforced specimen had obvious improvement.The maximum increased rate about peak load and ductility of the joint reinforced specimen is 100.6%and 233.4%,respectively.展开更多
Glass powder of various particle sizes(2,5,10 and 15μm)has been assessed as a possible cement substitute for mortars.Different replacement rates of cement(5%,10%,15%,and 20%)have been considered for all particle size...Glass powder of various particle sizes(2,5,10 and 15μm)has been assessed as a possible cement substitute for mortars.Different replacement rates of cement(5%,10%,15%,and 20%)have been considered for all particle sizes.The accessible porosity,compressive strength,gas permeability and microstructure have been investigated accordingly.The results have shown that adding glass powder up to 20%has a significantly negative effect on the porosity and compressive strength of mortar.The compressive strength initially rises with a 5%replacement and then decreases.Similarly,the gas permeability of the mortar displays a non-monotonic behavior;first,it decreases and then it grows with an increase in the glass powder content and particle size.The porosity and gas permeability attain a minimum for a 5%content and 10μm particle size.Application of a Nuclear magnetic resonance(NMR)technique has revealed that incorporating waste glass powder with a certainfineness can reduce the pore size and the number of pores of the mortar.Compared with the control mortar,the pore volume of the waste glass mortar with 5%and 10μm particle size is significantly reduced.When cement is partially replaced by glass powder with a particle size of 10μm and a 5%percentage,the penetration resistance and compressive strength of the mortar are significantly improved.展开更多
The combined use of silica fume(SF)and ceramic waste(CW)for the production of mortar is studied.Sand is replaced by 5%,10%,15%and 20%of CW while a fixed 5%percentage(%wt of cement)of SF is used.The results show that t...The combined use of silica fume(SF)and ceramic waste(CW)for the production of mortar is studied.Sand is replaced by 5%,10%,15%and 20%of CW while a fixed 5%percentage(%wt of cement)of SF is used.The results show that the best results are obtained by using silica fume and ceramic waste sand with 15%weight of sand and 5%wt of cement.With the addition of sand ceramic waste(SCW),the mortar compressive strength and density increase,while the porosity displays an opposite trend.The experimental analysis is complemented with theoretical considerations on the matrix strength and related improvements in mechanical behavior.It is shown that the agreement between the experimental values and the estimated values is good.展开更多
In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag ...In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.展开更多
This study aims to investigate the efiect of the mesoscopic characteristics of mineral powder fillers on the rutting resistance of asphalt mortar.Extraction and sieving tests were used to obtain the buton rock asphalt...This study aims to investigate the efiect of the mesoscopic characteristics of mineral powder fillers on the rutting resistance of asphalt mortar.Extraction and sieving tests were used to obtain the buton rock asphalt(BRA)ash with particle size smaller than 0.075 mm,which is consistent with that of the conventional mineral powder.The mesoscopic characteristics of BRA ash and conventional mineral powder were measured by SEM image analysis and the osmotic free pressure water method.Mesoscopic structure models of structural and free asphalts in mortar were obtained.The 70#matrix asphalt was used to prepare two kinds of asphalt mortar with BRA ash and conventional mineral powders fillers.The rutting factor of the two asphalt mortars was tested by dynamic shear test(DSR).Test results show that the ash extracted from BRA has a similar mesoscopic classification with the conventional mineral powder.Still,its fractal dimensions are larger,indicating the particles in BRA ash have more complex shapes and rougher surfaces,which is beneficial for forming structural asphalt and subsequently increasing the rutting factor(G*/sinδ),i e,improving the rutting resistance of the asphalt mortar.展开更多
The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars.The effects of two different types of Bayer red mud with varying physical a...The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars.The effects of two different types of Bayer red mud with varying physical and chemical characteristics on the fluidity,mechanical strength,mineral composition,and microstructure of the composite cement mortar were systematically evaluated.The results showed that the optimal addition of red mud A was 10 wt%,while it was 20 wt% for red mud B.The mechanical properties of the composite cement mortar met the standards for P·O42.5 cement.Furthermore,the composite mortar with the addition of red mud B showed higher flexural and compressive strengths compared to the composite mortar with red mud A.This improvement is attributed to the smaller particle size of red mud B,which filled the micro-pores and increased the compactness of the cement stone,as well as its higher content of Na_(2)O,K_(2)O,and other free alkalis,which resulted in more obvious alkali activation,accelerating the hydration of the active minerals in the slurry.展开更多
The disappearance of resources with high genetic potential and great utility for people and the challenge of the conservation and sustainable management of these resources are two opposing facts of which the world is ...The disappearance of resources with high genetic potential and great utility for people and the challenge of the conservation and sustainable management of these resources are two opposing facts of which the world is now concerned. In Benin, forests and agroforestry systems complement each other in wood supply for mortar and pestle manufacture. Thus, this study aimed to investigate the diversity of woody species used for mortar and pestle manufacture and to analyze the preferences of manufacturers through an ethnobotanical approach. Based on the snowball sampling method, and interviews with 112 manufacturers from different ethnic groups, we identified 31 tree species. These species belong to 30 genera and 13 plant families. The Fabaceae are more represented with 14 species (i.e. 45% of the total). Ten are frequently used. But there are four species, such as Vitellaria paradoxa C. F. Gaertn., Prosopis africana (Guill. & Perr.) Taub., Terminalia glaucescens Planch. ex Benth. and Pericopsis laxiflora (Benth.) Meeuwen, which are highly preferred by manufacturers respectively. The calculation of the Indexes of Possession of Global Knowledge (IPSG) revealed that the ethnic group Nagot (0.204) possessed more knowledge and is followed by Mahi (0.201) and Fon (0.18) respectively. Forests and agroforestry systems are both supply sites for manufacturers. The non-parametric Wilcoxon test proved that there are no significant differences between the species’ preference for mortars or pestles manufacture (v = 181, p-value = 0.38). Since the trees cutting in agroforestry systems can be destructive to them, provisions such as the promotion of agroforestry in rural areas and the integration of the used species in the reforestations programs must be taken to curb the pressure and contribute to the conservation of the biodiversity.展开更多
To explore ways to improve the accuracy of quantitative analysis of samples in the micrometer to nanometer range of magnitudes,we adopted analytical transmission electron microscopy(AEM/EDS)for qualitative and quantit...To explore ways to improve the accuracy of quantitative analysis of samples in the micrometer to nanometer range of magnitudes,we adopted analytical transmission electron microscopy(AEM/EDS)for qualitative and quantitative analysis of pyrite materials.Additionally,the k factor of pyrite is calculated experimentally.To develop an appropriate non-standard quantitative analysis model for pyrite materials,the experimentally calculated k factor is compared with that estimated from the non-standard quantitative analytical model of the instrument software.The experimental findings demonstrate that the EDS attached to a TEM can be employed for precise quantitative analysis of micro-and nanoscale regions of pyrite materials.Furthermore,it serves as a reference for improving the results of the EDS quantitative analysis of other sulfides.展开更多
To understand the effects offiller-asphalt ratio on different properties of lignin and polyesterfiber reinforced shape memory polyurethane(SMPU)/styrene butadiene styrene(SBS)composite modified asphalt mortar(PSAM),as we...To understand the effects offiller-asphalt ratio on different properties of lignin and polyesterfiber reinforced shape memory polyurethane(SMPU)/styrene butadiene styrene(SBS)composite modified asphalt mortar(PSAM),as well as to reveal the reinforcing and toughening mechanisms of lignin and polyesterfibers on PSAM,SMPU,SBS and mineral powder werefirst utilized to prepare PSAM.Then the conventional,rheological and anti-cracking properties of ligninfiber reinforced PSAM(LFAM)and polyesterfiber reinforced PSAM(PFAM)at dif-ferentfiller-asphalt ratios were characterized.Test results indicate that the shear strength,deformation resistance and viscosity are increased after adding 0.8wt%ligninfiber or polyesterfiber and increasing thefiller-asphalt ratio from 0.8 to 1.2.The optimalfiller-asphalt ratio of 1.0 is proposed after comprehensive performance assessments of PSAM.Polyesterfiber shows a better reinforcing effect than ligninfiber,but its improvement in the thermal stability of PSAM is not significant at high temperatures.Additionally,the complex modulus,storage modulus,loss modulus and rutting resistance factor of PSAM are improved after adding ligninfiber and polyesterfiber,as well as show an increasing trend as thefiller-asphalt ratio is raised,but the phase angle is gradually decreased.Further,the increase of elastic components in PSAM effectively enhances the anti-deformation ability of PSAM at high temperatures,and polyesterfiber more obviously improves the high-temperature deformation resistance of PSAM than ligninfiber.Finally,the anti-cracking performance of PFAM and LFAM at low temperatures is reduced by 74.2%and 46.7%,respectively,as thefiller-asphalt ratio is raised from 0.8 to 1.2.The low-temperature anti-cracking performance of LFAM is lower than that of PFAM at the samefiller-asphalt ratio,even lower than that of PSA.Compared with ligninfiber,the anti-cracking performance and deformation resistance of PSAM at low temperature is more greatly enhanced by polyester fiber.展开更多
Purpose–The construction of cement asphalt(CA)emulsified mortar can obviously disturb the slab status after the fine adjustment.To decrease or eliminate the influence of CA mortar grouting on track slab geometry stat...Purpose–The construction of cement asphalt(CA)emulsified mortar can obviously disturb the slab status after the fine adjustment.To decrease or eliminate the influence of CA mortar grouting on track slab geometry status,the effects of grouting funnel,slab pressing method,mortar expansion ratio,seepage ratio and grouting area on China Railway Track System Type(CRTS I)track slab geometry status were discussed in this paper.Design/methodology/approach–Combined with engineering practice,this paper studied the expansion law of filling layer mortar,the liquid level height of the filling funnel,the pressure plate device and the amount of exudation water and systematically analyzed the influence of filling layer mortar construction on the state of track slab.Relevant precautions and countermeasures were put forward.Findings–The results showed that the track slab floating values of four corners were different with the CA mortar grouting and the track slab corner near CA mortar grouting hole had the maximum floating values.The anti-floating effect of“7”shaped slab pressing device was more efficient than fixed-joint angle iron,and the slab floating value could be further decreased by increasing the amount of“7”shaped slab pressing devices.After CA mortar grouting,the track slab floating pattern had a close correlation with the expansion rate and water seepage rate of CA mortar over time and the expansion and water seepage rate of the mortar were faster when the temperature was high.Furthermore,the use of strip CA mortar filling under the rail bearing platform on bothsides could effectively reduce the float under the track slab,and it could also save mortar consumption and reduce costs.Originality/value–This study plays an important role in controlling the floating values,CA mortar dosage and the building cost of projects by grouting CA mortar at two flanks of filling space.The research results have guiding significance for the design and construction of China’s CRTS I,CRTS II and CRTS III track slab.展开更多
基金Funded by the National Natural Science Foundation of China (Nos. 52278269, 52278268, 52178264, 52108238)Tianjin Outstanding Young Scholars Science Fund Project (No. 22JCJQJC00020)State Key Laboratory of Green Building Materials Open Foundation (No. 2021GBM08)。
文摘To explore the role of biofilm formation on the corrosion of marine concrete structures, we investigated the attachment of biofilm on mortar surfaces in simulated seawater and the influence of biofilm on the microstructure of mortar surfaces. The results show that the evolution of biofilm on mortar surfaces in simulated seawater is closely related to the corrosion suffered by the mortar, and the process of biofilm attachment and shedding is continuous and cyclical. It is found that the specimens in the absence of biofilm attachment are more severely eroded internally by the corrosive medium in simulated seawater than those in the presence of biofilm attachment. For the specimens without biofilm attachment, after 60 days, gypsum forms,and after 120 days, the number of pores in the mortar is reduced. In contrast, for the specimens in the presence of biofilm attachment, gypsum could only be detected after 90 days, and fewer pores are filled. Therefore, the formation of biofilm could delay the invasion of the corrosive medium into the interior of mortar during the evolution of biofilm on mortar surfaces, mitigating the corrosion of mortars in seawater.
基金This work is supported by the Zhuhai Science and Technology Project(ZH22036203200015PWC)the Open Foundation of State Key Laboratory of Subtropical Building Science(2022ZB20).
文摘In this paper,the durability of cement mortar prepared with a recycled-concrete fine powder(RFP)was examined;including the analysis of a variety of aspects,such as the carbonization,sulfate attack and chloride ion erosion resistance.The results indicate that the influence of RFP on these three aspects is different.The carbonization depth after 30 days and the chloride diffusion coefficient of mortar containing 10%RFP decreased by 13.3%and 28.19%.With a further increase in the RFP content,interconnected pores formed between the RFP particles,leading to an acceleration of the penetration rate of CO_(2)and Cl^(−).When the RFP content was less than 50%,the corrosion resistance coefficient of the compressive strength of the mortar was 0.84-1.05 after 90 days of sulfate attack.But the expansion and cracking of the mortar was effectively alleviated due to decrease of the gypsum production.Scanning electron microscope(SEM)analysis has confirmed that 10%RFP contributes to the formation of a dense microstructure in the cement mortar.
基金This article was funded by the National Natural Science Foundation of China(No.51408610).
文摘Purpose–During the construction process of the China Railway Track System(CRTS)I type filling layer,the nonwoven fabric bags have been used as grouting templates for cement asphalt(CA)emulsified mortar.The porous structure of nonwoven fabrics endowed the templates with breathability and water permeability.The standard requires that the volume expansion rate of CA mortar must be controlled within 1%–3%,which can generate expansion pressure to ensure that the cavities under track slabs are filled fully.However,the expansion pressure caused some of the water to seep out from the periphery of the filling bag,and it would affect the actual mix proportion of CA mortar.The differences in physical and mechanical properties between the CA mortar under track slabs and the CA mortar formed in the laboratory were studied in this paper.The relevant results could provide important methods for the research of filling layer materials for CRTS I type and other types of ballastless tracks in China.Design/methodology/approach–During the inspection of filling layer,the samples of CA mortar from different working conditions and raw materials were taken by uncovering the track slabs and drilling cores.The physical and mechanical properties of CA mortar under the filling layer of the slab were systematically analyzed by testing the electrical flux,compressive strength and density of mortar in different parts of the filling layer.Findings–In this paper,the electric flux,the physical properties and mechanical properties of different parts of CA mortar under the track slab were investigated.The results showed that the density,electric flux and compressive strength of CA mortar were affected by the composition of raw materials for dry powders and different parts of the filling layer.In addition,the electrical flux of CA mortar gradually decreased within 90 days’age.The electrical flux of samples with the thickness of 54 mm was lower than 500 C.Therefore,the impermeability and durability of CA mortar could be improved by increasing the thickness of filling layer.Besides,the results showed that the compressive strength of CA mortar increased,while the density and electric flux decreased gradually,with the prolongation of hardening time.Originality/value–During 90 days’age,the electrical flux of the CA mortar gradually decreased with the increase of specimen thickness and the electrical flux of the specimens with the thickness of 54 mm was lower than 500 C.The impermeability and durability of the CA mortar could be improved by increasing the thickness of filling layer.The proposed method can provide reference for the further development and improvement of CRTS I and CRTS II type ballastless track in China.
文摘The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.
基金support provided by the Strategic Program of Chinese Academy of Sciences (Grant No. XDB10030400)the Hundred Talent Program of Chinese Academy of Sciences (Grant No. Y323081C01)
文摘In this paper, a compression-to-tension conversion technique is developed by applying predominant mode I loading test, using a servo-controlled compression system. The technique is applied to thin mortar plate specimens of different widths that include a prefabricated crack on either a single side to facilitate unilateral crack propagation, or prefabricated cracks positioned on both sides asymmetrically with respect to the specimen midpoint to facilitate bilateral crack propagation under direct tensile stress with a loading rate of 0.001 mm/s. The results show that the main pathways of unilateral crack propagation governing specimen failure are fluctuated locally, but present an approximately straight line overall in the absence of pre-existing internal defects. However, the pathways of bilateral crack propagation are relatively complex, although they present similar characteristics. Analysis results suggest that bilateral crack propagation can be basically divided into three stages, i.e. a stage of linear propagation, a stage representing deviation from the other crack, and a stage where one crack approaches either the other crack or approaches the opposite edge of the specimen, and thereby forming a continuous crack through the specimen. In addition, the stressestrain curves of bilateral crack specimens do not vary significantly around the point of peak stress prior to specimen failure, which means that the specimens do not fail instantaneously.
基金Funded by the National Natural Science Foundation of China(No.51878245)Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX22_0622)。
文摘We completed the uniaxial tensile test of mortar in the range of strain rate from 10^(-6)to 10^(-4)s^(-1)in the section containing softening,and carried out acoustic emission monitoring(AE)simultaneously.A series of AE parameters and spectrum analysis methods were used to identify the damage evolution process and cracking mechanism of mortar at different strain rates.The results show that,with the increase of strain rate,the peak stress and tensile elastic modulus of mortar increase obviously,and the stress level corresponding to the starting point of AE activity increases significantly as well,which indicates that the mechanical properties and AE characteristics of mortar have obvious strain rate effect.With the increase of strain rate,the cumulative AE hit decreases gradually,while the average AE hit rate increases significantly,indicating that the increase of strain rate reduces the damage degree of internal microstructure of the specimen,but the crack propagation speed increases.In the pre-peak stress stage,the average of AE ringing count and signal energy decreases with the increase of strain rate,while the average of duration increases;in the post-peak stress stage(f_(t)-30%f_(t)),the average of the three AE parameters all increase with the increase of strain rate,indicating that the strain rate effect on the damage process of mortar is different before and after peak stress,and the damage mechanism represented by different parameters is also different.In the whole process of uniaxial tensile of mortar,with the increase of strain rate,the scatter distribution of AE frequency-amplitude becomes more discrete,and the b-value shows a decreasing trend.In addition,the average level of AE peak frequency decreases with the increase of strain rate,while that of ca8 band wavelet energy spectrum coefficient increases.It is indicated that the increase of strain rate enables the crack propagation state of mortar specimen to become unstable,and the width of macrocrack increases but the proportion decreases.
基金supported by the National Natural Science Foundation of China(Grant No.51709097).
文摘Two different freeze-thaw cycles(FTC)are considered in this study to assess the related impact on gas permeability and micro-pore structure of a mortar.These are the water-freezing/water-thawing(WF-WT)and the air-freezing/air-thawing(AF-AT)cycles.The problem is addressed experimentally through an advanced nuclear magnetic resonance(NMR)technique able to provide meaningful information on the relationships among gas permeability,pore structure,mechanical properties,and the number of cycles.It is shown that the mortar gas permeability increases with the number of FTCs,the increase factor being 20 and 12.83 after 40 cycles for the WF-WT and AF-AT,respectively.The results also confirm that gas permeability hysteresis phenomena occur during the confining pressure loading and unloading process.
文摘The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal conductivity and hydration.The results showed that with the addition of 0.7%by weight of NFC per emulsion in the presence of a cationic surfactant(CTAB).The new material produced presented a dry porosity between 4.7%and 4.4%,compressive strength between 9.8 and 22.9 MPa,and thermal conductivity between 0.95 and 2.25 W·m^(−1)·K^(−1).Thus we show better mechanical and thermal performance than that traditional Portland cement mortar with a density similar.In addition,the mortar made by emulsion of ordinary portland cement,cellulose nanofiber and organophilic clay(OC)treated with cetyltrimethylammonium bromide(CTAB)obtained has good resistance under high temperature and water,as well as excellent thermal insulation performance under high temperature and humidity conditions.This study verified that the presence of NFC promotes hydration,leading to the production of more calcium silicate and portlandite gel.
基金This work is supported by the National Natural Science Foundation of China(No.51709097).
文摘This study deals with the analysis of the detrimental effects of a“sulfate attack”on cement mortar for different dry-wet cycles.The mass loss,tensile strength,and gas permeability coefficient were determined and analyzed under different exposure conditions.At the same time,nitrogen adsorption(NAD),scanning electron microscopy(SEM),and X-ray diffraction(XRD)techniques were used to analyze the corresponding variations in the microstructure and the corrosion products.The results show that certain properties of the cement mortar evolve differently according to the durations of the dry-wet cycles and that some damage is caused to the mortars in aqueous solution.The pores fill with corrosion products,increasing the mortar specimen mass and tensile strength while reducing the permeability coefficient and pore size distribution.As corrosion proceeds,the crystallization pressure of the corrosion products increases,resulting in a 16%reduction in tensile strength from the initial value and a 2.6-factor increase in the permeability coefficient,indicating sensitivity to sulfate attack damage.Furthermore,the main corrosion products generated in the experiment are gypsum and ettringite.Application of osmotic pressure and extension of the immersion time can accelerate the erosion process.
基金Funded by National Natural Science Foundation of China(Nos.51772212,51402216,51978505)。
文摘This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Results indicate that there is a non-linear relationship between the corrosion degree of steel reinforcement in CAC mortar and the concentration of NaCl solution.The electrochemical parameters of specimens immersed in 3%NaCl solution suddenly drop at 40 days,earlier than 60 days of the reference.And the charge transfer resistivity of the specimen has decreased by 11 orders of magnitude at 40 days,showing an evident corrosion on steel reinforcement.However,it is interesting to notice that the corrosion is delayed by high external chloride concentration.The specimens immersed in 9%and 15%NaCl solutions remain in a relatively stable state within 120 days with slight pitting.The great corrosion protection of CAC concrete to embedded steel bars enables its wide application in marine.
基金National Natural Science Foundation of China under Grant Nos.51968047 and 51608249the Key Research and Development Program of Jiangxi Province under Grant No.20161BBG70058。
文摘Since masonry structures are prone to collapse in earthquakes,a novel joint reinforcement method with a polypropylene band(PP-band)and cement mortar(CM)has been put forward.Compared with the common reinforcement methods,this method not only facilitates construction but also ensures lower reinforcement cost.To systematically explore the influence of joint reinforcement on the seismic performance of masonry walls,quasi-static tests were carried out on six specimens with different reinforcement forms.The test results show that the joint action of PP-band and CM can significantly improve the specimen′s brittle failure characteristics and enhance the integrity of the specimen after cracking.Compared with the specimen without reinforcement,each of the seismic performance indexes of the joint reinforced specimen had obvious improvement.The maximum increased rate about peak load and ductility of the joint reinforced specimen is 100.6%and 233.4%,respectively.
基金This work is supported by the National Natural Science Foundation of China(No.51709097).
文摘Glass powder of various particle sizes(2,5,10 and 15μm)has been assessed as a possible cement substitute for mortars.Different replacement rates of cement(5%,10%,15%,and 20%)have been considered for all particle sizes.The accessible porosity,compressive strength,gas permeability and microstructure have been investigated accordingly.The results have shown that adding glass powder up to 20%has a significantly negative effect on the porosity and compressive strength of mortar.The compressive strength initially rises with a 5%replacement and then decreases.Similarly,the gas permeability of the mortar displays a non-monotonic behavior;first,it decreases and then it grows with an increase in the glass powder content and particle size.The porosity and gas permeability attain a minimum for a 5%content and 10μm particle size.Application of a Nuclear magnetic resonance(NMR)technique has revealed that incorporating waste glass powder with a certainfineness can reduce the pore size and the number of pores of the mortar.Compared with the control mortar,the pore volume of the waste glass mortar with 5%and 10μm particle size is significantly reduced.When cement is partially replaced by glass powder with a particle size of 10μm and a 5%percentage,the penetration resistance and compressive strength of the mortar are significantly improved.
文摘The combined use of silica fume(SF)and ceramic waste(CW)for the production of mortar is studied.Sand is replaced by 5%,10%,15%and 20%of CW while a fixed 5%percentage(%wt of cement)of SF is used.The results show that the best results are obtained by using silica fume and ceramic waste sand with 15%weight of sand and 5%wt of cement.With the addition of sand ceramic waste(SCW),the mortar compressive strength and density increase,while the porosity displays an opposite trend.The experimental analysis is complemented with theoretical considerations on the matrix strength and related improvements in mechanical behavior.It is shown that the agreement between the experimental values and the estimated values is good.
基金Funded by National Natural Science Foundation of China(No.52278446)。
文摘In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.
基金Funded by the National Natural Science Foundation of China(No.51978088)。
文摘This study aims to investigate the efiect of the mesoscopic characteristics of mineral powder fillers on the rutting resistance of asphalt mortar.Extraction and sieving tests were used to obtain the buton rock asphalt(BRA)ash with particle size smaller than 0.075 mm,which is consistent with that of the conventional mineral powder.The mesoscopic characteristics of BRA ash and conventional mineral powder were measured by SEM image analysis and the osmotic free pressure water method.Mesoscopic structure models of structural and free asphalts in mortar were obtained.The 70#matrix asphalt was used to prepare two kinds of asphalt mortar with BRA ash and conventional mineral powders fillers.The rutting factor of the two asphalt mortars was tested by dynamic shear test(DSR).Test results show that the ash extracted from BRA has a similar mesoscopic classification with the conventional mineral powder.Still,its fractal dimensions are larger,indicating the particles in BRA ash have more complex shapes and rougher surfaces,which is beneficial for forming structural asphalt and subsequently increasing the rutting factor(G*/sinδ),i e,improving the rutting resistance of the asphalt mortar.
基金the Guangxi Science and Technology Program(Guike AD21220052,AD22035126 and AB22035064)National Natural Science Foundation of China(52062009)Guangxi Key Laboratory of New Energy and Building Energy Saving(Guikeneng 22-J-21-19).
文摘The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars.The effects of two different types of Bayer red mud with varying physical and chemical characteristics on the fluidity,mechanical strength,mineral composition,and microstructure of the composite cement mortar were systematically evaluated.The results showed that the optimal addition of red mud A was 10 wt%,while it was 20 wt% for red mud B.The mechanical properties of the composite cement mortar met the standards for P·O42.5 cement.Furthermore,the composite mortar with the addition of red mud B showed higher flexural and compressive strengths compared to the composite mortar with red mud A.This improvement is attributed to the smaller particle size of red mud B,which filled the micro-pores and increased the compactness of the cement stone,as well as its higher content of Na_(2)O,K_(2)O,and other free alkalis,which resulted in more obvious alkali activation,accelerating the hydration of the active minerals in the slurry.
文摘The disappearance of resources with high genetic potential and great utility for people and the challenge of the conservation and sustainable management of these resources are two opposing facts of which the world is now concerned. In Benin, forests and agroforestry systems complement each other in wood supply for mortar and pestle manufacture. Thus, this study aimed to investigate the diversity of woody species used for mortar and pestle manufacture and to analyze the preferences of manufacturers through an ethnobotanical approach. Based on the snowball sampling method, and interviews with 112 manufacturers from different ethnic groups, we identified 31 tree species. These species belong to 30 genera and 13 plant families. The Fabaceae are more represented with 14 species (i.e. 45% of the total). Ten are frequently used. But there are four species, such as Vitellaria paradoxa C. F. Gaertn., Prosopis africana (Guill. & Perr.) Taub., Terminalia glaucescens Planch. ex Benth. and Pericopsis laxiflora (Benth.) Meeuwen, which are highly preferred by manufacturers respectively. The calculation of the Indexes of Possession of Global Knowledge (IPSG) revealed that the ethnic group Nagot (0.204) possessed more knowledge and is followed by Mahi (0.201) and Fon (0.18) respectively. Forests and agroforestry systems are both supply sites for manufacturers. The non-parametric Wilcoxon test proved that there are no significant differences between the species’ preference for mortars or pestles manufacture (v = 181, p-value = 0.38). Since the trees cutting in agroforestry systems can be destructive to them, provisions such as the promotion of agroforestry in rural areas and the integration of the used species in the reforestations programs must be taken to curb the pressure and contribute to the conservation of the biodiversity.
基金Funded by the International Science&Technology Cooperation Program of Hubei Province of China(No.2022EHB024)。
文摘To explore ways to improve the accuracy of quantitative analysis of samples in the micrometer to nanometer range of magnitudes,we adopted analytical transmission electron microscopy(AEM/EDS)for qualitative and quantitative analysis of pyrite materials.Additionally,the k factor of pyrite is calculated experimentally.To develop an appropriate non-standard quantitative analysis model for pyrite materials,the experimentally calculated k factor is compared with that estimated from the non-standard quantitative analytical model of the instrument software.The experimental findings demonstrate that the EDS attached to a TEM can be employed for precise quantitative analysis of micro-and nanoscale regions of pyrite materials.Furthermore,it serves as a reference for improving the results of the EDS quantitative analysis of other sulfides.
基金This work was supported by National Natural Science Foundation of China(No.52208440)Natural Science Foundation of Jiangsu Province(BK20210618)+1 种基金the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(21KJB580003)National Undergraduate Training Program for Innovation and Entrepreneurship(2021NFUSPITP0638).
文摘To understand the effects offiller-asphalt ratio on different properties of lignin and polyesterfiber reinforced shape memory polyurethane(SMPU)/styrene butadiene styrene(SBS)composite modified asphalt mortar(PSAM),as well as to reveal the reinforcing and toughening mechanisms of lignin and polyesterfibers on PSAM,SMPU,SBS and mineral powder werefirst utilized to prepare PSAM.Then the conventional,rheological and anti-cracking properties of ligninfiber reinforced PSAM(LFAM)and polyesterfiber reinforced PSAM(PFAM)at dif-ferentfiller-asphalt ratios were characterized.Test results indicate that the shear strength,deformation resistance and viscosity are increased after adding 0.8wt%ligninfiber or polyesterfiber and increasing thefiller-asphalt ratio from 0.8 to 1.2.The optimalfiller-asphalt ratio of 1.0 is proposed after comprehensive performance assessments of PSAM.Polyesterfiber shows a better reinforcing effect than ligninfiber,but its improvement in the thermal stability of PSAM is not significant at high temperatures.Additionally,the complex modulus,storage modulus,loss modulus and rutting resistance factor of PSAM are improved after adding ligninfiber and polyesterfiber,as well as show an increasing trend as thefiller-asphalt ratio is raised,but the phase angle is gradually decreased.Further,the increase of elastic components in PSAM effectively enhances the anti-deformation ability of PSAM at high temperatures,and polyesterfiber more obviously improves the high-temperature deformation resistance of PSAM than ligninfiber.Finally,the anti-cracking performance of PFAM and LFAM at low temperatures is reduced by 74.2%and 46.7%,respectively,as thefiller-asphalt ratio is raised from 0.8 to 1.2.The low-temperature anti-cracking performance of LFAM is lower than that of PFAM at the samefiller-asphalt ratio,even lower than that of PSA.Compared with ligninfiber,the anti-cracking performance and deformation resistance of PSAM at low temperature is more greatly enhanced by polyester fiber.
基金funded by the National Natural Science Foundation of China(No.51408610).
文摘Purpose–The construction of cement asphalt(CA)emulsified mortar can obviously disturb the slab status after the fine adjustment.To decrease or eliminate the influence of CA mortar grouting on track slab geometry status,the effects of grouting funnel,slab pressing method,mortar expansion ratio,seepage ratio and grouting area on China Railway Track System Type(CRTS I)track slab geometry status were discussed in this paper.Design/methodology/approach–Combined with engineering practice,this paper studied the expansion law of filling layer mortar,the liquid level height of the filling funnel,the pressure plate device and the amount of exudation water and systematically analyzed the influence of filling layer mortar construction on the state of track slab.Relevant precautions and countermeasures were put forward.Findings–The results showed that the track slab floating values of four corners were different with the CA mortar grouting and the track slab corner near CA mortar grouting hole had the maximum floating values.The anti-floating effect of“7”shaped slab pressing device was more efficient than fixed-joint angle iron,and the slab floating value could be further decreased by increasing the amount of“7”shaped slab pressing devices.After CA mortar grouting,the track slab floating pattern had a close correlation with the expansion rate and water seepage rate of CA mortar over time and the expansion and water seepage rate of the mortar were faster when the temperature was high.Furthermore,the use of strip CA mortar filling under the rail bearing platform on bothsides could effectively reduce the float under the track slab,and it could also save mortar consumption and reduce costs.Originality/value–This study plays an important role in controlling the floating values,CA mortar dosage and the building cost of projects by grouting CA mortar at two flanks of filling space.The research results have guiding significance for the design and construction of China’s CRTS I,CRTS II and CRTS III track slab.
