Conventional plasticizers deteriorate mechanical and viscoelastic properties of the propellants due to their migration upon aging and long-term storage,which affects reliability and safety properties during exploitati...Conventional plasticizers deteriorate mechanical and viscoelastic properties of the propellants due to their migration upon aging and long-term storage,which affects reliability and safety properties during exploitation.To address this issue,conventional plasticizer,dioctyl adipate(DOA),is replaced by reactive one,castor oil(CO).In addition,three different types of HTPB were used to obtain propellants with designed viscoelastic and mechanical properties.The CO increased propellants viscosity,without a significant impact on the propellant processability,regardless to the type of prepolymer.Conversely,mechanical properties were different depending on the type of resin,which were further analyzed by gel permeation chromatography(GPC).Addition of CO formed a denser polymer network and shifted T_(g) to higher values,compared to the compositions with DOA.The tensile strength of CO-containing propellants was lower at +20℃ and +50℃ compared to the reference compositions,while the strain at maximum load and strain at break were significantly increased with pronounced plastic deformation,especially for samples at -30℃.The inclusion of CO in the propellants composition gives more room for adjusting a wide range of mechanical properties.展开更多
The effects of 5 lactic acid bacteria(LAB)fermentation on the pasting properties of glutinous rice flour were compared,and suitable fermentation strains were selected based on the changes of viscosity,setback value,an...The effects of 5 lactic acid bacteria(LAB)fermentation on the pasting properties of glutinous rice flour were compared,and suitable fermentation strains were selected based on the changes of viscosity,setback value,and breakdown value to prepare LAB compound starter cultures.The results revealed that Latilactobacillus sakei HSD004 and Lacticaseibacillus rhamnosus HSD005 had apparent advantages in increasing the viscosity and reducing the setback and breakdown values of glutinous rice flour.In particular,the compound starter created using the two abovementioned LAB in the ratio of 3:1 had better performance than that using a single LAB in improving the pasting properties and increasing the water and oil absorption capacity of glutinous rice flour.Moreover,the gelatinization enthalpy of the fermented samples increased significantly.For frozen glutinous rice dough stored for 28 days,the viscoelasticity of frozen dough prepared by compound starter was better than that of control dough,and the freezable water content was lower than that of control dough.These results indicate that compound LAB fermentation is a promising technology in the glutinous rice-based food processing industry,which has significance for its application.展开更多
The composite laminates with embedded acrylonitrile butadiene rubber （NBR） layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through t...The composite laminates with embedded acrylonitrile butadiene rubber （NBR） layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through the damping layer and completely couple the structure to improve bending stiffness and interlaminar shearing strength of these cocured composite laminates. The damping, bending stiffness and shearing strength of these composite laminates with different perforation diameters were investigated. The experimental results show that increasing the perforation diameter leads to significant decreases in damping and significant increase in bending stiffness up to an area ratio of 7.065%. The area ratio here is defined as the ratio of perforation area to the total damping area. Beyond the area ratio of 7.065%, increasing the diameter to an area ratio of 50.24% results in only a slight variation in damping and bending stiffness. Moreover, increasing the perforation diameter does not always increase the shearing strength of the embedded viscoelastic layer. The shearing strength of embedded viscoelastic layer increases only when the area ratio is greater than 19.625%; instead, it will decrease.展开更多
Viscoelastic properties of maleated polypropylene （MAPP）-modified wood flour/polypropylene composites （WPC） were investigated by both a compression stress relaxation method and dynamic mechanical analyses （DMA）....Viscoelastic properties of maleated polypropylene （MAPP）-modified wood flour/polypropylene composites （WPC） were investigated by both a compression stress relaxation method and dynamic mechanical analyses （DMA）. Three wood to polymer ratios （40：60, 60：40, and 80：20） and five MAPP loading levels （0, 1, 2, 4 and 8%） were used to study their effects on the viscoelastic prop- erties of MAPP-WPC. The results show that： 1） higher wood to polymer ratio corresponds to higher stress relaxation levels for unmodified WPC. The modification with MAPP has an obvious effect on the stress relaxation of MAPP-WPC at higher wood to polymer ratios （60：40 and 80：20）, but almost no effect at the 40：60 wood to polymer ratio. The optimal MAPP loading level for the wood to polymer ratio of 60：40 appears at 1%; 2） the storage modulus reaches its maximum at a MAPP loading level of 1% for wood to polymer ratios of 40：60 and 60：40, while for the 80：20 wood to polymer ratio, a higher storage modulus is observed at higher MAPP loading levels, which is quite consistent with the stress relaxation results. The results suggested that a suitable loading level of MAPP has a positive effect on the viscoelastic properties of WPC at higher wood to polymer ratios. Excessive MAPP loading would have resulted in adverse effects.展开更多
The aim of this paper is to apply the asymptotic homogenization method to determining analytically and numerically the transversely isotropic viscoelastic relaxation moduli of the equivalent particle for the intercala...The aim of this paper is to apply the asymptotic homogenization method to determining analytically and numerically the transversely isotropic viscoelastic relaxation moduli of the equivalent particle for the intercalated multi-layer stack of intercalated type nanoplastics. A two-phase multilayered material containing n layers is considered. The matrix is assumed to be an isotropic viscoelastic standard linear body and the reinforcement is assumed to be an isotropic elastic body. Final explicit analytical formulae for the effective elastic moduli of the multilay- ered material are derived first; and then the correspondence principle is employed to obtain the homogenized relaxation moduli of the equivalent intercalated particle. A numerical example is given. Final explicit analytical formulae in the time domain derived here make it convenient to estimate the influence of all the particle parameters of micro-structural details on the effective properties of the equivalent intercalated particle. The results of this paper can also be applied to multi-layer composites.展开更多
This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid...This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid properties, slip velocity, and internal heat generation/absorption. The flow in boundary layer is considered to be generated solely by the stretching of the sheet adjacent to porous medium with boundary wall slip condition. Highly nonlinear momentum and thermal boundary layer equations governing the flow and heat transfer are reduced to set of nonlinear ordinary differential equations by appropriate transformation. The resulting ODEs are successfully solved numerically with the help of shooting method. Graphical results are shown for non-dimensional velocities and temperature. The effects of heat generation/absorption parameter, the porous parameter, the viscoelastic parameter, velocity slip parameter, variable thermal conductivity and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction coefficient and Nusselt number are presented. Comparison of numerical results is made with the earlier published results under limiting cases.展开更多
Significant correlations exist for the total sample between the dough viscoelastic properties and quality, but little information about these links is available. This study investigates the relationship between the gl...Significant correlations exist for the total sample between the dough viscoelastic properties and quality, but little information about these links is available. This study investigates the relationship between the gluten molecular conformation and the dough viscoelastic properties of the Zhengmai 379 wheat variety with different relative humidity(RH) values during storage.The results showed that protein extractability, free sulfhydryl(SH) groups, and wet gluten contents decreased to a certain degree during storage, while the glutenin quantity significantly varied. Significant negative correlation coefficients were found between the dough viscosity at 50% RH and the β-turn contents at 40% RH(-0.918) or 60% RH(-0.949)(P < 0.01), the dough viscosity at50% RH and the β-turn contents at 50% RH(-0.912)(P < 0.05), and the dough viscosity at 50% RH and the α-helix/β-sheet ratio at 40% RH(-0.875), 50% RH(-0.869), or 60% RH(-0.843)(P < 0.05). Significant correlation coefficients were further observed between the dough viscosity at 50% RH and the β-sheet contents at 60% RH(0.927)(P < 0.01) and between the dough viscosity at50% RH and the β-sheet contents at 40% RH(0.910) or 50% RH(0.908)(P < 0.05). A decrease in the free SH groups of gluten and an increase in the low-molecular weight contents suggested that gliadin was incorporated via SS crosslinking to the glutenin-like protein, which did not dissolve in ethanol.展开更多
Corn bran was subjected to high-shear and jet-cooking with or without alkaline treatment. The highest antioxidant activity was found in the soluble solids from jet-cooked corn bran without alkaline treatment. Jet-cook...Corn bran was subjected to high-shear and jet-cooking with or without alkaline treatment. The highest antioxidant activity was found in the soluble solids from jet-cooked corn bran without alkaline treatment. Jet-cooking under alkaline conditions resulted in a soluble fraction having the highest phenolic content but without increasing antioxidant activity. Phenolic contents of soluble solids were significantly higher than the insoluble solids. A colorimetric method using spectrophotometer was suitable to determine total phenolic content, whereas LC-ESI-MS technology was used for identifying important individual phenolic acids, namely caffeic, coumaric and ferulic acid. The insoluble solids from alkaline treatment had the highest water holding capacity and interesting viscoelastic properties. These results suggested that jet-cooking corn bran may be a useful processing procedure for creating phytochemical and functional products.展开更多
Mathematical model describing the processes of mechanical stress development in response to strain of heterogeneous muscle fiber is created. The numerical algorithm to calculate viscoelastic properties of muscle fiber...Mathematical model describing the processes of mechanical stress development in response to strain of heterogeneous muscle fiber is created. The numerical algorithm to calculate viscoelastic properties of muscle fiber of arbitrary length is developed. In numerical experiments by the model it is shown that the local heterogeneity of geometrical and mechanical parameters of structural units of the model significantly influences in resulting mechanical response of whole fiber. Also it is established the close connection between parameters of mechanical and geometrical heterogeneity compensating each other. It is supposed that the mechanism may modulate the myocardial remodeling under changing load.展开更多
Viscoelastic properties of skeletal muscle are associated with a complex network of cytoskeletal proteins where titin and nebulin play a substantial role. The need for evaluation of muscle viscoelastic properties is w...Viscoelastic properties of skeletal muscle are associated with a complex network of cytoskeletal proteins where titin and nebulin play a substantial role. The need for evaluation of muscle viscoelastic properties is widely accepted in clinical use to evaluate the effect of treatment or progression of muscle pathology (atrophy). We tested the hypothesis that the viscoelastic properties (elasticity, tone and stiffness) change in atrophied muscles with concomitant changes in cytoskeletal proteins (titin, nebulin) and contractile protein (myosin heavy chain) proportion. Sixteen 24- week-old male rats of the Wistar strain were randomly allocated to two groups: dexamethasone group treated each day for 10 consecutive days with dexamethasone in order to induce atrophy and control group. Skeletal muscle viscoelastic properties (elasticity, tone and stiffness) were determined using a myotonometer. Titin, nebulin and myosin heavy chain content were quantified using SDS-PAGE electrophoresis. We found that glucocorticoid-induced muscle atrophy is accompanied by reduced elasticity and increased tone and stiffness, with concomitant changes in titin, nebulin and myosin heavy chain con- tent. The elasticity decreased by 10.9% (P P < 0.05), and stiffness was significantly lower in dexamethasone group (627.3 N/m vs 758.6 N/m);(P < 0.05). Compared with the control group, the content of titin, nebulin and myosin heavy chain in atrophied muscle was 76.4%, 70.6% and 82.3%, respectively. Our results may lead to a better understanding of the mechanism of muscle atrophy and provide better guidance for rehabilitation practices and help to find rational therapeutic intervention in the future.展开更多
This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foamsfrom biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate)(PET) were...This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foamsfrom biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate)(PET) were used to synthesize PU polyols. Addition of adipic acid (ADA) to polyol resulted in improvedthermal and viscoelastic properties of foam materials. ADA content was varied from 1 to 6 wt%. Results ofthe dynamic mechanical spectra indicate an increase of the storage modulus E′ and the loss modulus E″ inthe whole temperature range for specimens with higher loading of ADA. In addition, damping factor shiftedto higher temperatures, but damping intensity remained almost unaffected by the compositions. Scanningelectron microscopy of the foams’ cross sections testified that the average cells’ size of 110 mm was unaffectedby the ADA content in polyol.展开更多
Several gelatin-silicate composites, with or without incorporation of Ca2+ ions, were synthesized through sol-gel processing starting from gelatin and 3- (glycidoxypropyl) trimethoxysilane. The structure around the Si...Several gelatin-silicate composites, with or without incorporation of Ca2+ ions, were synthesized through sol-gel processing starting from gelatin and 3- (glycidoxypropyl) trimethoxysilane. The structure around the Si atoms was similar for all the samples. The measurement of viscoelastic properties indicated that the glass transition temperature and activation energy decreased with the incorporation of Ca2+ ions. The Ca2+ ion-containing composites were bioactive as they spontaneously deposited apatite when soaked in a simulated body fluid of the Kokubo recipe.展开更多
This study investigated the viscoelastic and rheometeric properties of PVC stabilized with tannin-Ca complex as totally bio-based thermal stabilizer. Dynamic mechanical thermal analysis (DMTA) used to characterize the...This study investigated the viscoelastic and rheometeric properties of PVC stabilized with tannin-Ca complex as totally bio-based thermal stabilizer. Dynamic mechanical thermal analysis (DMTA) used to characterize the viscoelastic properties of PVC samples obtained by thermal mixing of PVC with three composition percentages (1.0, 2.0, and 3.0) part per hundred ratios (phr) of tannin-Ca complex with this polymer. The torque rheometery test used to monitor the effect of tannins derivative on the thermal stability and mixing properties of PVC formulations during samples processing. For that purpose, PVC sample with 2 phr commercial thermal stabilizer (Reapak B-NT/ 7060) was used for comparison and considered as reference samples. Before the glass transition temperature of PVC at 30°C - 60°C, the DMTA curves show that the values of storage modulus and tan delta of PVC samples stabilized with tannin derivative were very similar with those of PVC sample stabilized with commercial thermal stabilizer. The glass transition temperature (Tg) of PVC stabilized with commercial thermal stabilizer and with tannin-Ca complex occurred at about 76°C. In a sequence, after the glass transition region of PVC samples, the DMTA scans confirmed that the PVC samples with 2 phr tannin-Ca complex have relatively longer flowing stage which occurs at lower temperatures by 18°C per that of PVC sample stabilized with commercial stabilizer. Global results of the torque rheometery which have suitable plateau stages and the DMTA show that the processing thermal stability and thermal flexibility of PVC are clearly increased with the incorporation of tannin-Ca complex. All the PVC formulations with tannins-Ca complex show excellent viscoelastic properties which were found to be slightly best or much closed to those obtained for PVC stabilized with commercial thermal stabilization.展开更多
It is a novel idea to make steamed bread by adding potato flour into wheat flour considering the production and nutritional factors of potato. In this study, the influence of potato flour（0–35%） on dough rheology a...It is a novel idea to make steamed bread by adding potato flour into wheat flour considering the production and nutritional factors of potato. In this study, the influence of potato flour（0–35%） on dough rheology and quality of steamed bread were investigated. Potato flour addition significantly influenced the dough rheological properties and steamed bread quality, such as increased water absorption, the maximum gaseous release height, total volume of CO_2 and hardness, while decreased dough stability and specific volume of steamed bread. Moreover, correlation analysis suggested that dough height at the maximum development time, dough stability, water absorption and the phase tangent can be used for predicting the technological quality of steamed bread. Potato-wheat steamed bread had higher dietary fibre, ash content and antioxidant activity than those of wheat steamed bread. The estimated glycemic index decreased from 73.63（0%） to 60.01（35%）. Considering the sensory evaluation, the steamed bread with 20% potato flour is acceptable. In conclusion, adding appropriate quantity of potato flour to wheat flour for steamed bread production will not only maintain the technological quality, but also can improve the nutritional value of the steamed bread.展开更多
In this work, the rheological changes of several crude oil samples exposed to ultrasonic waves for different time intervals in addition to the effect of temperature on viscosity behavior of heavy crude oils were inves...In this work, the rheological changes of several crude oil samples exposed to ultrasonic waves for different time intervals in addition to the effect of temperature on viscosity behavior of heavy crude oils were investigated using a series of steady shear flow and oscillatory tests. The colloidal structural evolutions of flocs in oil samples were illustrated by analysis of the size distribution of flocculated asphaltene particles （confocal microscopy tests）. The rheological investigations indicate that the ultrasonic irradiation dissolved heavy components in crude oil. After ultrasonic treatment, the Kouh-e-Mond crude oil was found to be pseudoplastic. In addition, confocal microscopy confirms that there was an optimum duration for ultrasonic irradiation, at which the viscosity and flocculation rate of asphaltenic crude oils reduced to the minimum values. The optimum was found to be approximately 40 min for the Kouh-e-Mond crude oil. Experimental results illustrate that the ultrasonic irradiation could disaggregate heavy colloid components in crude oil, and breakdown of asphaltene molecules would only occur in a specific time interval of irradiation. Also according to the temperature sweep test, the oil temperature rise caused by ultrasonic irradiation was not the main reason for theological changes of the crude oil and this alteration may be due to physical and chemical phenomena induced by sonication in crude oil.展开更多
The transplantation of artificial blood vessels with 〈 6 mm inner diameter as substitutes for human arterioles or veins has not achieved satisfactory results. Umbilical vein has been substituted for ar- tery in vascu...The transplantation of artificial blood vessels with 〈 6 mm inner diameter as substitutes for human arterioles or veins has not achieved satisfactory results. Umbilical vein has been substituted for ar- tery in vascular transplantation, but it remains unclear whether the stress relaxation and creep be- tween these vessels are consistent. In this study, we used the fetal umbilical vein and middle cere- bral artery from adult male cadavers to make specimens 15 mm in length, 0.196-0.268 mm in tu- nica media thickness, and 2.82-2.96 mm in outer diameter. The results demonstrated that the stress decrease at 7 200 seconds was similar between the middle cerebral artery and fetal umbilical vein specimens, regardless of initial stress of 18.7 kPa or 22.5 kPa. However, the strain increase at 7 200 seconds of fetal umbilical veins was larger than that of middle cerebral arteries. Moreover, the stress relaxation experiment showed that the stress decrease at 7 200 seconds of the fetal umbilical vein and middle cerebral artery specimens under 22.5 kPa initial stress was less than the decrease in these specimens under 18.7 kPa initial stress. These results indicate that the fetal umbilical vein has appropriate stress relaxation and creep properties for transplantation. These properties are advantageous for vascular reconstruction, indicating that the fetal umbilical vein can be transplanted to repair middle cerebral artery injury.展开更多
The aim of the study was to determine the influence of wheat bran dietary fiber on wheat flour dough rheological properties.In this paper,wheat bran dietary fiber(WBDF)with different levels(0,3%,6%,9%,12%)were added t...The aim of the study was to determine the influence of wheat bran dietary fiber on wheat flour dough rheological properties.In this paper,wheat bran dietary fiber(WBDF)with different levels(0,3%,6%,9%,12%)were added to wheat flour and the characterization of dough rheological properties was conducted by rapid visco-analyzer,farinograph,as well as rotational rheometer.The results from pasting properties showed a gradual reduction in peak viscosity,trough viscosity,final viscosity and setback with increasing WBDF content.At high WBDF concentration,the significant increase of water absorption,formation time as well as weakening degree implied the harder formation of gluten network structure and the competition for water between gluten and WBDF particles.Such conclusion was in line with the findings from dynamic rheology tests,in which the doughs containing WBDF were more sensitive to strain regardless of their rigid and stiff texture.This study revealed vulnerable dough structure induced by WBDF,as well as the strengthened elastic property,elaborating the harmful effects ofWBDF on the rheological properties of doughs.展开更多
We investigated the natural oscillations of dissipative inhomogeneous plate mechanical systems with point connections. Based on the principle of virtual displacements, we equate to zero the sum of all active work forc...We investigated the natural oscillations of dissipative inhomogeneous plate mechanical systems with point connections. Based on the principle of virtual displacements, we equate to zero the sum of all active work force, including the force of inertia which obtain equations vibrations of mechanical systems. Frequency equation is solved numerically by the method of Muller. According to the result of numerical analysis we established nonmonotonic dependence damping coefficients of the system parameters.展开更多
We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis（DMTA） method. The experimental results show that the dynamic mechani...We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis（DMTA） method. The experimental results show that the dynamic mechanical properties of cement asphalt pastes are sensitive to temperature due to the inclusion of asphalt, and may go through different states within a temperature range of-40 ℃ to 60 ℃, which is different from that of pure cement and asphalt. As the temperature of the cement asphalt paste increases, a considerable change of dynamic mechanical properties, including storage modulus（E＇）, loss modulus（E＇＇） and loss factor（tand） is observed. Moreover, the influence of asphalt to cement（A/C） ratio on the temperature sensitivity of the dynamic mechanical properties of cement asphalt composites was investigated. The temperature dependency of cement asphalt composites is ascribed to the temperature dependency of the asphalt and its interaction with cement paste. A simple fractional model is proposed to describe the viscoelastic behavior of cement asphalt composites.展开更多
An analysis of the response of surface acoustic wave sensors coated with polymer film based on new coating deposition （self-assemble and molecularly imprinted technology） is described and the response formulas are h...An analysis of the response of surface acoustic wave sensors coated with polymer film based on new coating deposition （self-assemble and molecularly imprinted technology） is described and the response formulas are hence deduced. Using the real part of shear modulus, the polymer can be classified into three types： glassy film, glassy-rubbery film and rubbery film, Experimental results show that the attenuation response is in better consistence with the simulation than in Martin＇s theory, but the velocity response does not accord with the calculation exactly. Maybe it is influenced by the experimental methods and environment. In addition, simulations of gas sorption for polymer films are performed. As for glassy film, the SAW sensor response increases with increasing fihn thickness, and the relationship between the sensor response and the concentration of gas is pretty linear, while as for glassy-rubbery flint and rubbery film, the relationship between the sensor sensitivity anti concentration of gas is very complicated. The ultimately calculated results indicate that the relationship between the sensor response and frequency is not always linear due to the viscoelastic prooerties of the polymer.展开更多
基金the support of this research from the Serbian Ministry of Education,Science and Technological Development(Grant No.451-03-68/2023-14/200325)Ministry of Defense(Grant No.VA-TT/1/22-24)。
文摘Conventional plasticizers deteriorate mechanical and viscoelastic properties of the propellants due to their migration upon aging and long-term storage,which affects reliability and safety properties during exploitation.To address this issue,conventional plasticizer,dioctyl adipate(DOA),is replaced by reactive one,castor oil(CO).In addition,three different types of HTPB were used to obtain propellants with designed viscoelastic and mechanical properties.The CO increased propellants viscosity,without a significant impact on the propellant processability,regardless to the type of prepolymer.Conversely,mechanical properties were different depending on the type of resin,which were further analyzed by gel permeation chromatography(GPC).Addition of CO formed a denser polymer network and shifted T_(g) to higher values,compared to the compositions with DOA.The tensile strength of CO-containing propellants was lower at +20℃ and +50℃ compared to the reference compositions,while the strain at maximum load and strain at break were significantly increased with pronounced plastic deformation,especially for samples at -30℃.The inclusion of CO in the propellants composition gives more room for adjusting a wide range of mechanical properties.
基金supported by the National Key Research and Development Program of China(2021YFD2100902-3)the National Natural Science Foundation of China(32072258)+5 种基金Major Science and Technology Program of Heilongjiang(2020ZX08B02)Harbin University of Commerce“Young Innovative Talents”Support Program(2019CX062020CX262020CX27)the Central Financial Support for the Development of Local Colleges and Universities,Graduate Innovation Research Project of Harbin University of Commerce(YJSCX2021-698HSD)Training plan of Young Innovative Talents in Universities of Heilongjiang(UNPYSCT-2020218).
文摘The effects of 5 lactic acid bacteria(LAB)fermentation on the pasting properties of glutinous rice flour were compared,and suitable fermentation strains were selected based on the changes of viscosity,setback value,and breakdown value to prepare LAB compound starter cultures.The results revealed that Latilactobacillus sakei HSD004 and Lacticaseibacillus rhamnosus HSD005 had apparent advantages in increasing the viscosity and reducing the setback and breakdown values of glutinous rice flour.In particular,the compound starter created using the two abovementioned LAB in the ratio of 3:1 had better performance than that using a single LAB in improving the pasting properties and increasing the water and oil absorption capacity of glutinous rice flour.Moreover,the gelatinization enthalpy of the fermented samples increased significantly.For frozen glutinous rice dough stored for 28 days,the viscoelasticity of frozen dough prepared by compound starter was better than that of control dough,and the freezable water content was lower than that of control dough.These results indicate that compound LAB fermentation is a promising technology in the glutinous rice-based food processing industry,which has significance for its application.
基金supported from the Center for Composites Material and Structure of Harbin Institute of Technology,China
文摘The composite laminates with embedded acrylonitrile butadiene rubber （NBR） layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through the damping layer and completely couple the structure to improve bending stiffness and interlaminar shearing strength of these cocured composite laminates. The damping, bending stiffness and shearing strength of these composite laminates with different perforation diameters were investigated. The experimental results show that increasing the perforation diameter leads to significant decreases in damping and significant increase in bending stiffness up to an area ratio of 7.065%. The area ratio here is defined as the ratio of perforation area to the total damping area. Beyond the area ratio of 7.065%, increasing the diameter to an area ratio of 50.24% results in only a slight variation in damping and bending stiffness. Moreover, increasing the perforation diameter does not always increase the shearing strength of the embedded viscoelastic layer. The shearing strength of embedded viscoelastic layer increases only when the area ratio is greater than 19.625%; instead, it will decrease.
基金supported by the National Natural Science Foundation of China (Grant No. 30871966)
文摘Viscoelastic properties of maleated polypropylene （MAPP）-modified wood flour/polypropylene composites （WPC） were investigated by both a compression stress relaxation method and dynamic mechanical analyses （DMA）. Three wood to polymer ratios （40：60, 60：40, and 80：20） and five MAPP loading levels （0, 1, 2, 4 and 8%） were used to study their effects on the viscoelastic prop- erties of MAPP-WPC. The results show that： 1） higher wood to polymer ratio corresponds to higher stress relaxation levels for unmodified WPC. The modification with MAPP has an obvious effect on the stress relaxation of MAPP-WPC at higher wood to polymer ratios （60：40 and 80：20）, but almost no effect at the 40：60 wood to polymer ratio. The optimal MAPP loading level for the wood to polymer ratio of 60：40 appears at 1%; 2） the storage modulus reaches its maximum at a MAPP loading level of 1% for wood to polymer ratios of 40：60 and 60：40, while for the 80：20 wood to polymer ratio, a higher storage modulus is observed at higher MAPP loading levels, which is quite consistent with the stress relaxation results. The results suggested that a suitable loading level of MAPP has a positive effect on the viscoelastic properties of WPC at higher wood to polymer ratios. Excessive MAPP loading would have resulted in adverse effects.
基金Project supported by the National Natural Science Foundation of China (Grant Nos.10672138 and 10372087).
文摘The aim of this paper is to apply the asymptotic homogenization method to determining analytically and numerically the transversely isotropic viscoelastic relaxation moduli of the equivalent particle for the intercalated multi-layer stack of intercalated type nanoplastics. A two-phase multilayered material containing n layers is considered. The matrix is assumed to be an isotropic viscoelastic standard linear body and the reinforcement is assumed to be an isotropic elastic body. Final explicit analytical formulae for the effective elastic moduli of the multilay- ered material are derived first; and then the correspondence principle is employed to obtain the homogenized relaxation moduli of the equivalent intercalated particle. A numerical example is given. Final explicit analytical formulae in the time domain derived here make it convenient to estimate the influence of all the particle parameters of micro-structural details on the effective properties of the equivalent intercalated particle. The results of this paper can also be applied to multi-layer composites.
文摘This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid properties, slip velocity, and internal heat generation/absorption. The flow in boundary layer is considered to be generated solely by the stretching of the sheet adjacent to porous medium with boundary wall slip condition. Highly nonlinear momentum and thermal boundary layer equations governing the flow and heat transfer are reduced to set of nonlinear ordinary differential equations by appropriate transformation. The resulting ODEs are successfully solved numerically with the help of shooting method. Graphical results are shown for non-dimensional velocities and temperature. The effects of heat generation/absorption parameter, the porous parameter, the viscoelastic parameter, velocity slip parameter, variable thermal conductivity and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction coefficient and Nusselt number are presented. Comparison of numerical results is made with the earlier published results under limiting cases.
基金Supported by National Key Research and Development Program(2016YFD0400203)National Natural Science Foundation of China(31571780 and 31771897)+2 种基金General Science and Technology Research Projects of Zhengzhou(N2013G0077)Key Scientific Research Project of Universities in Henan Province(16A210018)the focus on Fostering Basic Research Fund of Henan University of Technology(2013JCYJ05)
文摘Significant correlations exist for the total sample between the dough viscoelastic properties and quality, but little information about these links is available. This study investigates the relationship between the gluten molecular conformation and the dough viscoelastic properties of the Zhengmai 379 wheat variety with different relative humidity(RH) values during storage.The results showed that protein extractability, free sulfhydryl(SH) groups, and wet gluten contents decreased to a certain degree during storage, while the glutenin quantity significantly varied. Significant negative correlation coefficients were found between the dough viscosity at 50% RH and the β-turn contents at 40% RH(-0.918) or 60% RH(-0.949)(P < 0.01), the dough viscosity at50% RH and the β-turn contents at 50% RH(-0.912)(P < 0.05), and the dough viscosity at 50% RH and the α-helix/β-sheet ratio at 40% RH(-0.875), 50% RH(-0.869), or 60% RH(-0.843)(P < 0.05). Significant correlation coefficients were further observed between the dough viscosity at 50% RH and the β-sheet contents at 60% RH(0.927)(P < 0.01) and between the dough viscosity at50% RH and the β-sheet contents at 40% RH(0.910) or 50% RH(0.908)(P < 0.05). A decrease in the free SH groups of gluten and an increase in the low-molecular weight contents suggested that gliadin was incorporated via SS crosslinking to the glutenin-like protein, which did not dissolve in ethanol.
文摘Corn bran was subjected to high-shear and jet-cooking with or without alkaline treatment. The highest antioxidant activity was found in the soluble solids from jet-cooked corn bran without alkaline treatment. Jet-cooking under alkaline conditions resulted in a soluble fraction having the highest phenolic content but without increasing antioxidant activity. Phenolic contents of soluble solids were significantly higher than the insoluble solids. A colorimetric method using spectrophotometer was suitable to determine total phenolic content, whereas LC-ESI-MS technology was used for identifying important individual phenolic acids, namely caffeic, coumaric and ferulic acid. The insoluble solids from alkaline treatment had the highest water holding capacity and interesting viscoelastic properties. These results suggested that jet-cooking corn bran may be a useful processing procedure for creating phytochemical and functional products.
文摘Mathematical model describing the processes of mechanical stress development in response to strain of heterogeneous muscle fiber is created. The numerical algorithm to calculate viscoelastic properties of muscle fiber of arbitrary length is developed. In numerical experiments by the model it is shown that the local heterogeneity of geometrical and mechanical parameters of structural units of the model significantly influences in resulting mechanical response of whole fiber. Also it is established the close connection between parameters of mechanical and geometrical heterogeneity compensating each other. It is supposed that the mechanism may modulate the myocardial remodeling under changing load.
文摘Viscoelastic properties of skeletal muscle are associated with a complex network of cytoskeletal proteins where titin and nebulin play a substantial role. The need for evaluation of muscle viscoelastic properties is widely accepted in clinical use to evaluate the effect of treatment or progression of muscle pathology (atrophy). We tested the hypothesis that the viscoelastic properties (elasticity, tone and stiffness) change in atrophied muscles with concomitant changes in cytoskeletal proteins (titin, nebulin) and contractile protein (myosin heavy chain) proportion. Sixteen 24- week-old male rats of the Wistar strain were randomly allocated to two groups: dexamethasone group treated each day for 10 consecutive days with dexamethasone in order to induce atrophy and control group. Skeletal muscle viscoelastic properties (elasticity, tone and stiffness) were determined using a myotonometer. Titin, nebulin and myosin heavy chain content were quantified using SDS-PAGE electrophoresis. We found that glucocorticoid-induced muscle atrophy is accompanied by reduced elasticity and increased tone and stiffness, with concomitant changes in titin, nebulin and myosin heavy chain con- tent. The elasticity decreased by 10.9% (P P < 0.05), and stiffness was significantly lower in dexamethasone group (627.3 N/m vs 758.6 N/m);(P < 0.05). Compared with the control group, the content of titin, nebulin and myosin heavy chain in atrophied muscle was 76.4%, 70.6% and 82.3%, respectively. Our results may lead to a better understanding of the mechanism of muscle atrophy and provide better guidance for rehabilitation practices and help to find rational therapeutic intervention in the future.
文摘This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foamsfrom biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate)(PET) were used to synthesize PU polyols. Addition of adipic acid (ADA) to polyol resulted in improvedthermal and viscoelastic properties of foam materials. ADA content was varied from 1 to 6 wt%. Results ofthe dynamic mechanical spectra indicate an increase of the storage modulus E′ and the loss modulus E″ inthe whole temperature range for specimens with higher loading of ADA. In addition, damping factor shiftedto higher temperatures, but damping intensity remained almost unaffected by the compositions. Scanningelectron microscopy of the foams’ cross sections testified that the average cells’ size of 110 mm was unaffectedby the ADA content in polyol.
文摘Several gelatin-silicate composites, with or without incorporation of Ca2+ ions, were synthesized through sol-gel processing starting from gelatin and 3- (glycidoxypropyl) trimethoxysilane. The structure around the Si atoms was similar for all the samples. The measurement of viscoelastic properties indicated that the glass transition temperature and activation energy decreased with the incorporation of Ca2+ ions. The Ca2+ ion-containing composites were bioactive as they spontaneously deposited apatite when soaked in a simulated body fluid of the Kokubo recipe.
文摘This study investigated the viscoelastic and rheometeric properties of PVC stabilized with tannin-Ca complex as totally bio-based thermal stabilizer. Dynamic mechanical thermal analysis (DMTA) used to characterize the viscoelastic properties of PVC samples obtained by thermal mixing of PVC with three composition percentages (1.0, 2.0, and 3.0) part per hundred ratios (phr) of tannin-Ca complex with this polymer. The torque rheometery test used to monitor the effect of tannins derivative on the thermal stability and mixing properties of PVC formulations during samples processing. For that purpose, PVC sample with 2 phr commercial thermal stabilizer (Reapak B-NT/ 7060) was used for comparison and considered as reference samples. Before the glass transition temperature of PVC at 30°C - 60°C, the DMTA curves show that the values of storage modulus and tan delta of PVC samples stabilized with tannin derivative were very similar with those of PVC sample stabilized with commercial thermal stabilizer. The glass transition temperature (Tg) of PVC stabilized with commercial thermal stabilizer and with tannin-Ca complex occurred at about 76°C. In a sequence, after the glass transition region of PVC samples, the DMTA scans confirmed that the PVC samples with 2 phr tannin-Ca complex have relatively longer flowing stage which occurs at lower temperatures by 18°C per that of PVC sample stabilized with commercial stabilizer. Global results of the torque rheometery which have suitable plateau stages and the DMTA show that the processing thermal stability and thermal flexibility of PVC are clearly increased with the incorporation of tannin-Ca complex. All the PVC formulations with tannins-Ca complex show excellent viscoelastic properties which were found to be slightly best or much closed to those obtained for PVC stabilized with commercial thermal stabilization.
基金financed by the Public Welfare Industry(Agriculture)Research Project of China(201503001-2)the Agricultural Special Financial in 2015 of Chinathe Basic Research Expenses Budget Incremental Project of Chinese Academy of Agricultural Sciences(2014ZL009)
文摘It is a novel idea to make steamed bread by adding potato flour into wheat flour considering the production and nutritional factors of potato. In this study, the influence of potato flour（0–35%） on dough rheology and quality of steamed bread were investigated. Potato flour addition significantly influenced the dough rheological properties and steamed bread quality, such as increased water absorption, the maximum gaseous release height, total volume of CO_2 and hardness, while decreased dough stability and specific volume of steamed bread. Moreover, correlation analysis suggested that dough height at the maximum development time, dough stability, water absorption and the phase tangent can be used for predicting the technological quality of steamed bread. Potato-wheat steamed bread had higher dietary fibre, ash content and antioxidant activity than those of wheat steamed bread. The estimated glycemic index decreased from 73.63（0%） to 60.01（35%）. Considering the sensory evaluation, the steamed bread with 20% potato flour is acceptable. In conclusion, adding appropriate quantity of potato flour to wheat flour for steamed bread production will not only maintain the technological quality, but also can improve the nutritional value of the steamed bread.
文摘In this work, the rheological changes of several crude oil samples exposed to ultrasonic waves for different time intervals in addition to the effect of temperature on viscosity behavior of heavy crude oils were investigated using a series of steady shear flow and oscillatory tests. The colloidal structural evolutions of flocs in oil samples were illustrated by analysis of the size distribution of flocculated asphaltene particles （confocal microscopy tests）. The rheological investigations indicate that the ultrasonic irradiation dissolved heavy components in crude oil. After ultrasonic treatment, the Kouh-e-Mond crude oil was found to be pseudoplastic. In addition, confocal microscopy confirms that there was an optimum duration for ultrasonic irradiation, at which the viscosity and flocculation rate of asphaltenic crude oils reduced to the minimum values. The optimum was found to be approximately 40 min for the Kouh-e-Mond crude oil. Experimental results illustrate that the ultrasonic irradiation could disaggregate heavy colloid components in crude oil, and breakdown of asphaltene molecules would only occur in a specific time interval of irradiation. Also according to the temperature sweep test, the oil temperature rise caused by ultrasonic irradiation was not the main reason for theological changes of the crude oil and this alteration may be due to physical and chemical phenomena induced by sonication in crude oil.
文摘The transplantation of artificial blood vessels with 〈 6 mm inner diameter as substitutes for human arterioles or veins has not achieved satisfactory results. Umbilical vein has been substituted for ar- tery in vascular transplantation, but it remains unclear whether the stress relaxation and creep be- tween these vessels are consistent. In this study, we used the fetal umbilical vein and middle cere- bral artery from adult male cadavers to make specimens 15 mm in length, 0.196-0.268 mm in tu- nica media thickness, and 2.82-2.96 mm in outer diameter. The results demonstrated that the stress decrease at 7 200 seconds was similar between the middle cerebral artery and fetal umbilical vein specimens, regardless of initial stress of 18.7 kPa or 22.5 kPa. However, the strain increase at 7 200 seconds of fetal umbilical veins was larger than that of middle cerebral arteries. Moreover, the stress relaxation experiment showed that the stress decrease at 7 200 seconds of the fetal umbilical vein and middle cerebral artery specimens under 22.5 kPa initial stress was less than the decrease in these specimens under 18.7 kPa initial stress. These results indicate that the fetal umbilical vein has appropriate stress relaxation and creep properties for transplantation. These properties are advantageous for vascular reconstruction, indicating that the fetal umbilical vein can be transplanted to repair middle cerebral artery injury.
基金supported by Henan Province Colleges and Universities Young Backbone Teacher Plan (No. 2016GGJS-070)the Fundamental Research Funds for the Henan Provincial Colleges and Universities in Henan University of Technology (No. 2018RCJH08)National Natural Science Foundation of China (No. 31571873)
文摘The aim of the study was to determine the influence of wheat bran dietary fiber on wheat flour dough rheological properties.In this paper,wheat bran dietary fiber(WBDF)with different levels(0,3%,6%,9%,12%)were added to wheat flour and the characterization of dough rheological properties was conducted by rapid visco-analyzer,farinograph,as well as rotational rheometer.The results from pasting properties showed a gradual reduction in peak viscosity,trough viscosity,final viscosity and setback with increasing WBDF content.At high WBDF concentration,the significant increase of water absorption,formation time as well as weakening degree implied the harder formation of gluten network structure and the competition for water between gluten and WBDF particles.Such conclusion was in line with the findings from dynamic rheology tests,in which the doughs containing WBDF were more sensitive to strain regardless of their rigid and stiff texture.This study revealed vulnerable dough structure induced by WBDF,as well as the strengthened elastic property,elaborating the harmful effects ofWBDF on the rheological properties of doughs.
文摘We investigated the natural oscillations of dissipative inhomogeneous plate mechanical systems with point connections. Based on the principle of virtual displacements, we equate to zero the sum of all active work force, including the force of inertia which obtain equations vibrations of mechanical systems. Frequency equation is solved numerically by the method of Muller. According to the result of numerical analysis we established nonmonotonic dependence damping coefficients of the system parameters.
基金Funded by the National Natural Science Foundation of China(50878209 and 51208515)the National Basic Research Program of China(“973”Program)(2013CB036201)
文摘We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis（DMTA） method. The experimental results show that the dynamic mechanical properties of cement asphalt pastes are sensitive to temperature due to the inclusion of asphalt, and may go through different states within a temperature range of-40 ℃ to 60 ℃, which is different from that of pure cement and asphalt. As the temperature of the cement asphalt paste increases, a considerable change of dynamic mechanical properties, including storage modulus（E＇）, loss modulus（E＇＇） and loss factor（tand） is observed. Moreover, the influence of asphalt to cement（A/C） ratio on the temperature sensitivity of the dynamic mechanical properties of cement asphalt composites was investigated. The temperature dependency of cement asphalt composites is ascribed to the temperature dependency of the asphalt and its interaction with cement paste. A simple fractional model is proposed to describe the viscoelastic behavior of cement asphalt composites.
基金This work was supported by National Natural Science Foundation （No. 10374100）.
文摘An analysis of the response of surface acoustic wave sensors coated with polymer film based on new coating deposition （self-assemble and molecularly imprinted technology） is described and the response formulas are hence deduced. Using the real part of shear modulus, the polymer can be classified into three types： glassy film, glassy-rubbery film and rubbery film, Experimental results show that the attenuation response is in better consistence with the simulation than in Martin＇s theory, but the velocity response does not accord with the calculation exactly. Maybe it is influenced by the experimental methods and environment. In addition, simulations of gas sorption for polymer films are performed. As for glassy film, the SAW sensor response increases with increasing fihn thickness, and the relationship between the sensor response and the concentration of gas is pretty linear, while as for glassy-rubbery flint and rubbery film, the relationship between the sensor sensitivity anti concentration of gas is very complicated. The ultimately calculated results indicate that the relationship between the sensor response and frequency is not always linear due to the viscoelastic prooerties of the polymer.
