Pipelines produce vibrations during fluid or gas transportation.These vibrations are less likely to cause structural failure as they exist with a small magnitude and can be harvested into useful energy.This paper pres...Pipelines produce vibrations during fluid or gas transportation.These vibrations are less likely to cause structural failure as they exist with a small magnitude and can be harvested into useful energy.This paper presents a study on the piezoelectric energy-harvesting method converting mechanical energy from pipeline vibration into electrical energy.The performance of the serpentine-shaped piezoelectric cantilever beam was observed to check whether the design can produce the highest output voltage within the allowable vibration region of the pipeline from 10 to 300 Hz through finite element analysis using COMSOL Multiphysics software(Supplementary Material).In addition,this study investigates the energy-harvesting potential of the proposed design under real pipeline vibration conditions through a lab vibration test.The harvested energy output is evaluated based on various vibration frequencies and amplitudes,which gives an idea of the device and its performance under different operating conditions.The experiment result shows that the energy harvester produced an open-circuit voltage of 10.28-15.45 V with 1 g of vibration acceleration.The results of this research will contribute to the development of efficient piezoelectric energy harvesters adapted for pipeline environments.展开更多
A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigate...A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.展开更多
By applying the second order Melnikov function, the chaos behaviors of a bistable piezoelectric cantilever power generation system are analyzed. Firstly, the conditions for emerging chaos of the system are derived by ...By applying the second order Melnikov function, the chaos behaviors of a bistable piezoelectric cantilever power generation system are analyzed. Firstly, the conditions for emerging chaos of the system are derived by the second order Melnikov function. Secondly, the effects of each item in chaos threshold expression are analyzed. The excitation frequency and resistance values, which have the most influence on chaos threshold value, are found. The result from the second order Melnikov function is more accurate compared with that from the first order Melnikov function. Finally, the attraction basins of large amplitude motions under different exciting frequency, exciting amplitude, and resistance parameters are given.展开更多
According to specific bridge environment, optimal design piezoelectric cantilever beam structure by using results of theoretical calculations and simulation, verify natural frequencies of piezoelectric cantilever beam...According to specific bridge environment, optimal design piezoelectric cantilever beam structure by using results of theoretical calculations and simulation, verify natural frequencies of piezoelectric cantilever beam and production ability of data by experiment, thus formed a complete set of design method of piezoelectric cantilever beam. Considering natural frequency of vibration and intensity of the beam body, design a new type of piezoelectric cantilever beam structure. Paper analyzes the principle of sensor data acquisition and transmission, design a hardware integration system include signal conversion module, microcontroller module and wireless transmission module, test local read and wireless transmission for the combination structure of cantilever beam and data collection card, experimental verification of the radio piezoelectric vibrating cantilever vibration response is intact, the beam produced signal by vibration, acquisition card converts and wireless transmit data, this proved a good and intuitive linear response in simulation of bridge vibration test. Finally, the paper designed a kind of new wireless sensor of vibration cantilever beam, suitable for small bridge health monitoring based on Internet of things.展开更多
文摘Pipelines produce vibrations during fluid or gas transportation.These vibrations are less likely to cause structural failure as they exist with a small magnitude and can be harvested into useful energy.This paper presents a study on the piezoelectric energy-harvesting method converting mechanical energy from pipeline vibration into electrical energy.The performance of the serpentine-shaped piezoelectric cantilever beam was observed to check whether the design can produce the highest output voltage within the allowable vibration region of the pipeline from 10 to 300 Hz through finite element analysis using COMSOL Multiphysics software(Supplementary Material).In addition,this study investigates the energy-harvesting potential of the proposed design under real pipeline vibration conditions through a lab vibration test.The harvested energy output is evaluated based on various vibration frequencies and amplitudes,which gives an idea of the device and its performance under different operating conditions.The experiment result shows that the energy harvester produced an open-circuit voltage of 10.28-15.45 V with 1 g of vibration acceleration.The results of this research will contribute to the development of efficient piezoelectric energy harvesters adapted for pipeline environments.
文摘A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.
基金supported by the National Natural Science Foundation of China (Grant 11172199)
文摘By applying the second order Melnikov function, the chaos behaviors of a bistable piezoelectric cantilever power generation system are analyzed. Firstly, the conditions for emerging chaos of the system are derived by the second order Melnikov function. Secondly, the effects of each item in chaos threshold expression are analyzed. The excitation frequency and resistance values, which have the most influence on chaos threshold value, are found. The result from the second order Melnikov function is more accurate compared with that from the first order Melnikov function. Finally, the attraction basins of large amplitude motions under different exciting frequency, exciting amplitude, and resistance parameters are given.
文摘According to specific bridge environment, optimal design piezoelectric cantilever beam structure by using results of theoretical calculations and simulation, verify natural frequencies of piezoelectric cantilever beam and production ability of data by experiment, thus formed a complete set of design method of piezoelectric cantilever beam. Considering natural frequency of vibration and intensity of the beam body, design a new type of piezoelectric cantilever beam structure. Paper analyzes the principle of sensor data acquisition and transmission, design a hardware integration system include signal conversion module, microcontroller module and wireless transmission module, test local read and wireless transmission for the combination structure of cantilever beam and data collection card, experimental verification of the radio piezoelectric vibrating cantilever vibration response is intact, the beam produced signal by vibration, acquisition card converts and wireless transmit data, this proved a good and intuitive linear response in simulation of bridge vibration test. Finally, the paper designed a kind of new wireless sensor of vibration cantilever beam, suitable for small bridge health monitoring based on Internet of things.
