In recent years,explosion shock wave has been considered as a signature injury of the current military conflicts.Although strong shock wave is lethal to the human body,weak shock wave can cause many more lasting conse...In recent years,explosion shock wave has been considered as a signature injury of the current military conflicts.Although strong shock wave is lethal to the human body,weak shock wave can cause many more lasting consequences.To investigate the protection ability and characteristics of flexible materials and structures under weak shock wave loading,the blast wave produced by TNT explosive is loaded on the polyurethane foam with the density of 200.0 kg/m3(F-200)and 400.0 kg/m3(F-400),polyurea with the density of 1100.0 kg/m^(3)(P-1100)and structures composed of the two materials,which are intended for individual protection.Experimental results indicate that the shock wave is attenuated to weak pressure disturbance after interacting with the flexible materials which are not damaged.The shock wave protective capability of single-layer materials is dependent on their thickness,density and microscopic characteristics.The overpressure,maximum pressure rise rate and impulse of transmitted wave decrease exponentially with increase in sample thickness.For the same thickness,F-400 provides better protective capability than F-200 while P-1100 shows the best protective capability among the three materials.In this study,as the materials are not destroyed,F-200 with a thickness more than10.0 mm,F-400 with a thickness more than 4.0 mm,and P-1100 with a thickness more than 1.0 mm can attenuate the overpressure amplitude more than 90.0%.Further,multi-layer flexible composites are designed.Different layer layouts of designed structures and layer thickness of the single-layer materials can affect the protective performance.Within the research range,the structure in which polyurea is placed on the impact side shows the optimal shock wave protective performance,and the thicknesses of polyurea and polyurethane foam are 1.0 mm and 4.0 mm respectively.The overpressure attenuation rate reached maximum value of 93.3%and impulse attenuation capacity of this structure are better than those of single-layer polyurea and polyurethane foam with higher areal density.展开更多
Porous materials are widely used in the field of protection because of their excellent energy absorption characteristics.In this work,a series of polyurethane microscopic models are established and the effect of poros...Porous materials are widely used in the field of protection because of their excellent energy absorption characteristics.In this work,a series of polyurethane microscopic models are established and the effect of porosity on the shock waves is studied with classical molecular dynamics simulations.Firstly,shock Hugoniot relations for different porosities are obtained,which compare well with the experimental data.The pores collapse and form local stress wave,which results in the complex multi-wave structure of the shock wave.The microstructure analysis shows that the local stress increases and the local velocity decreases gradually during the process of pore collapse to complete compaction.Finally,it leads to stress relaxation and velocity homogenization.The shock stress peaks can be fitted with two exponential functions,and the amplitude of attenuation coefficient decreases with the increase of density.Besides,the pore collapse under shock or non-shock are discussed by the entropy increase rate of the system.The energy is dissipated mainly through the multiple interactions of the waves under shock.The energy is dissipated mainly by the friction between atoms under non-shock.展开更多
Cryogenic insulation material rigid polyurethane(PU)foams were developed using bio-based and recycled feedstock.Polyols obtained from tall oil fatty acids produced as a side stream of wood biomass pulping and recycled...Cryogenic insulation material rigid polyurethane(PU)foams were developed using bio-based and recycled feedstock.Polyols obtained from tall oil fatty acids produced as a side stream of wood biomass pulping and recycled polyethylene terephthalate were used to develop rigid PU foam formulations.The 4th generation physical blowing agents with low global warming potential and low ozone depletion potential were used to develop rigid PU foam cryogenic insulation with excellent mechanical and thermal properties.Obtained rigid PU foams had a thermal conductivity coefficient as low as 0.0171 W/m·K and an apparent density of 37-40 kg/m^(3).The developed rigid PU foams had anisotropic compression strength properties,which were higher parallel to the foaming direction.Moreover,the compression strength was also influenced by the type of applied bio-based polyol.The bio-based polyols with higher OH group functionality delivered higher crosslinking density of polymer matrix;thus,the mechanical properties were also higher.The mechanical strength of the foams increased when materials were tested at liquid nitrogen temperature due to the stiffening of the polymer matrix.The thermal properties of the developed materials were determined using differential scanning calorimetry,dynamic mechanical analysis,and thermogravimetric analysis methods.Lastly,the developed rigid PU foams had good adhesion to the aluminium substrate before and after applying cyroshock and an excellent safety coefficient of 4-5.Rigid PU foams developed using Solstice LBA delivered adhesion strength of~0.5 MPa and may be considered for application as cryogenic insulation in the aerospace industry.展开更多
In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore ...In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore size of 0.3 mm was investigated.The main factors affecting the deposition rate such as the solution composition,temperature,pH value and adding ultrasonic were explored.The results show that the optimum process conditions are CuSO4 16 g/L,HCHO 5 mL/L,NaKC4H4O6 30 g/L,Na2EDTA 20 g/L,K4Fe(CN)6 25 mg/L,pH value of 12.5-13.0 and temperature of 40-50℃.Under these technical conditions, the process has excellent bath stability.Adding ultrasonic on the process can elevate the deposition rate of copper by 20%-30%.The foam metal material with a porosity of 92.2%and a three-dimensional network structure,was fabricated by electro-deposition after the electroless copper plating.展开更多
Based on the mechanical properties and microstructure of polyurethane foam solidified material, a two-dimensional model of polyurethane foam solidified material was constructed. Polyurethane foam was obtained by fully...Based on the mechanical properties and microstructure of polyurethane foam solidified material, a two-dimensional model of polyurethane foam solidified material was constructed. Polyurethane foam was obtained by fully and uniformly mixing the two components. The research was carried out through the combination of experimental test and finite element simulation. The experimental results show that when the pore density is constant, the size of the bubble hole is an important factor affecting the mechanical properties of the model. The smaller the size of the bubble hole, the less likely it is to produce stress concentration inside the model, and the stronger the resistance to material deformation. Under the random distribution, the lower the density of the polyurethane cured material, the higher the probability of damage between the adjacent bubbles, which is not conducive to the stability of the material. The density of the cured material should not be lower than 199 kg/m^3.展开更多
Biomass phytic acid has potential flame retardant value as the main form of phosphorus in plant seeds.In this study,phytate-based flame retardants aluminum phytate(PA-Al)and iron phytate(PA-Fe)were synthesized and cha...Biomass phytic acid has potential flame retardant value as the main form of phosphorus in plant seeds.In this study,phytate-based flame retardants aluminum phytate(PA-Al)and iron phytate(PA-Fe)were synthesized and characterized.Subsequently,they were introduced into rigid polyurethane foam(RPUF)as flame retardants by one-step water-blown method.The results indicated that RPUF/PA-Fe30 exhibited the highest char residue of 22.1 wt%,significantly higher than 12.4 wt%of RPUF.Cone calorimetry analysis showed that the total heat release(THR)of RPUF/PA-Al30 decreased by 17.0%and total smoke release(TSR)decreased by 22.0%compared with pure RPUF,which were the lowest,demonstrating a low fire risk and good smoke suppression.Thermogravimetric analysis-Fourier transform infrared spectrometer(TG-FTIR)implied the release intensity of flammable gases(hydrocarbons,esters)and toxic gases(isocyanate,CO,aromatic compounds,HCN)of composites was significantly reduced after the addition of PA-Fe.The analysis of char residue indicated that the RPUF composites formed a dense char layer with a high degree of graphitization after the addition of PA-Al/PA-Fe,endowing RPUF composites with excellent mass&heat transmission inhibition effect and fire resistance in the combustion process.展开更多
Polyurethane foam dressings for dermal wounds were formulated with natural polyols in order to improve the foam characteristics and the release of 2 active agents,silver and asiaticoside(AS)as an antimicrobial agent a...Polyurethane foam dressings for dermal wounds were formulated with natural polyols in order to improve the foam characteristics and the release of 2 active agents,silver and asiaticoside(AS)as an antimicrobial agent and an herbal wound healing agent,respectively.The foam was instantly formed by interaction of polyols and diisocyanate.Hydroxypropyl methylcellulose,chitosan and sodium alginate were individually mixed with themain polyols,polypropylene glycol,in the formulation while the active componentswere impregnated into the obtained foam dressing sheets.Although the type and amount of the natural polyols slightly affected the pore size,water sorption-desorption profile and compression strength of the obtained foam sheets,a prominent effect was found in the release of both active components.Among natural polyols formulations,foam sheets with alginate showed the highest silver and AS release.Non-cytotoxicity of these foam sheets to human fibroblast cells was confirmed.Antimicrobial testing on four bacteria strains showed that 1mg/cm^2 silver in formulations with 6%of natural polyols and without natural polyols had sufficient content of the silver release with comparable inhibition zone and significantly larger zone than other formulations.In pig study,the foam dressing with 6%alginate,1mg/cm^2 silver and 5%AS could improve wound healing in both the percentage of the wound closure and histological parameters of the dermal wound without any dermatologic reactions.In conclusion,this innovative foam dressing had potential to be a good candidate for wound treatment.展开更多
The effect of a sandwiched cross-shaped metamaterial absorber(CMMA) on microwave absorption properties of the double-layered polyurethane foam absorber(PUFA) is investigated. Combining with the sandwiched CMMA, the ba...The effect of a sandwiched cross-shaped metamaterial absorber(CMMA) on microwave absorption properties of the double-layered polyurethane foam absorber(PUFA) is investigated. Combining with the sandwiched CMMA, the bandwidth of -10-dB reflection loss for PUFA is broadened from 7.4 GHz to 9.1 GHz, which is attributed to the overlap of two absorption peaks originating from CMMA and PUFA, respectively. The values of the two absorption peaks located at 10.15 GHz and 14.7 GHz are -38.44 dB and -40.91 dB, respectively. Additionally, distribution of surface current,electromagnetic field and power loss density are introduced to investigate the absorption mechanism of the CMMA. The electromagnetic field distribution of the double-layered PUFA and the three-layered hybrid absorber are comparatively analyzed to ascertain the influence of CMMA. The results show that the proposed hybrid absorber can be applied to the anti-electromagnetic interference and stealth technology.展开更多
In this study, polyurethane foam type thermoset polymerizing, due to chemical reaction between its liquid ingredients, was tested as binder after solidifying and then a rock-like material mixing with a sandy silt type...In this study, polyurethane foam type thermoset polymerizing, due to chemical reaction between its liquid ingredients, was tested as binder after solidifying and then a rock-like material mixing with a sandy silt type soil was prepared. The uniaxial compressive strengths(UCSs) of polyurethane foam reinforced soil specimens were determined for different polyurethane ratios in the mixture. Additionally,a series of tests on slake durability, impact value, freezingethawing resistance, and abrasion resistance of polyurethane reinforced soil(PRS) mixture was conducted. The UCS values over 3 MPa were measured from the PRS specimens. The testing results showed that treated soil can economically become a desirable rock-like material in terms of slake durability and resistances against freezingethawing, impact effect and abrasion. As another characteristic of the rock-like material made with polyurethane foam,unit volume weight was found to be quite lower than those of natural rock materials.展开更多
CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. Th...CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. They may find wide applications in many fields.展开更多
The production cost of flexible polyurethane foam is significantly dependent on the cost of polyol, which constitute the largest percentage of materials used in foam production with the characteracterics to induce sup...The production cost of flexible polyurethane foam is significantly dependent on the cost of polyol, which constitute the largest percentage of materials used in foam production with the characteracterics to induce superior mechanical properties. Suitable fillers that are relatively cheap can be introduced in the foam matrix as replacement for polyol. However, certain compositions of filler have deleterious effect on some relevant mechanical properties of the foam. This paper investigates the effect of CaCO3 filler in flexible polyurethane foam matrix for the dual purposes of achieving sustained mechanical properties and reduction in production cost. The optimum CaCO3 composition was found to be 20 wt % representing a concomitant 18.54% reduction in cost of production.展开更多
The two kinds of rigid polyurethane(PU) foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in we...The two kinds of rigid polyurethane(PU) foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight.The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams.The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples.The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently.Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples.The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.展开更多
A reconstruction method is proposed for the polyurethane foam and then a complete numerical method is developed to predict the effective thermal conductivity of the polyurethane foam. The finite volume method is appli...A reconstruction method is proposed for the polyurethane foam and then a complete numerical method is developed to predict the effective thermal conductivity of the polyurethane foam. The finite volume method is applied to solve the 2D heterogeneous pure conduction. The lattice Boltzmann method is adopted to solve the 1D homogenous radiative transfer equation rather than Rosseland approximation equation. The lattice Boltzmann method is then adopted to solve 1D homogeneous conduction-radiation energy transport equation considering the combined effect of conduction and radiation. To validate the accuracy of the present method, the hot disk method is adopted to measure the effective thermal conductivity of the polyurethane foams at different temperature. The numerical results agree well with the experimental data. Then, the influences of temperature, porosity and cell size on the effective thermal conductivity of the polyurethane foam are investigated. The results show that the effective thermal conductivity of the polyurethane foams increases with temperature; and the effective thermal conductivity of the polyurethane foams decreases with increasing porosity while increases with the cell size.展开更多
Effect of different chemicals and additives used in producing polyester foam was investigated. Reference samples were produced from polyol, toluene di isocyanate (TDI), amine stannous octoate distil water, and silicon...Effect of different chemicals and additives used in producing polyester foam was investigated. Reference samples were produced from polyol, toluene di isocyanate (TDI), amine stannous octoate distil water, and silicone oil using laboratory mix formulation based on 500 g polyether based polyol. Other samples were produced by consecutively varying the content of all the additives with the exception of polyol. Standard sample dimensions for density test, indentation test, compression set test, tensile strength and elongation tests were produced from the samples. The various tests were carried out on the samples using the ASTM-D3574 standards. It was observed that the degree of indentation affects the value of indentation hardness and increasing the percentage content of TDI results in acceptable compression set value for the polyester samples. It was concluded that Holding all other parameters constant, reducing the water content and increasing the TDI content will yield polyester foam of optimum properties.展开更多
This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foamsfrom biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate)(PET) were...This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foamsfrom biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate)(PET) were used to synthesize PU polyols. Addition of adipic acid (ADA) to polyol resulted in improvedthermal and viscoelastic properties of foam materials. ADA content was varied from 1 to 6 wt%. Results ofthe dynamic mechanical spectra indicate an increase of the storage modulus E′ and the loss modulus E″ inthe whole temperature range for specimens with higher loading of ADA. In addition, damping factor shiftedto higher temperatures, but damping intensity remained almost unaffected by the compositions. Scanningelectron microscopy of the foams’ cross sections testified that the average cells’ size of 110 mm was unaffectedby the ADA content in polyol.展开更多
Advanced wound dressings are replaced traditional dressings in order to provide appropriate environment for healing and also to promote cell migration[1].The key characteristics of wound dressings are non-toxic,highly...Advanced wound dressings are replaced traditional dressings in order to provide appropriate environment for healing and also to promote cell migration[1].The key characteristics of wound dressings are non-toxic,highly absorbed,air permeable,biocompatible and have good mechanical properties[2].Due to providing moist environment and also protecting maceration at the wound edge area,foam dressings are used in various clinical applications[3].They are mostly prepared from polyurethane between polyols and isocyanate polymerization.展开更多
Rigid polyurethane foam is found virtually everywhere in our modern world and is used in sound and thermal insulation applications such as refrigerators, insulated buildings, thermosets. Organometallic compounds are u...Rigid polyurethane foam is found virtually everywhere in our modern world and is used in sound and thermal insulation applications such as refrigerators, insulated buildings, thermosets. Organometallic compounds are used as polyurethane catalysts since they are very highly selective towards the isocyanate-polyol reaction. Also, amine catalysts are used to balance both the gelling reaction and the gas-forming or foaming reaction responsible for foam formation. In this work, the effect of a tin octoate catalyst on the mechanical properties and morphology of polyurethane foam were investigated. Also, the thermal conductivity and sound absorption coefficient for polyurethane foam mortar formulations were measured. The morphological properties of polyurethane foam were investigated using scanning electron microscope to determine the influence of varying the concentration of tin octoate. It was clear from the results that polyurethane foam has good thermal and sound insulation capabilities.展开更多
In this study, a series of flame-retardant polyisocyanurate-polyurethane (PIR-PUR) foams were prepared using various concentrations (0-25% by weight) of expandable graphite (EG) and dimethyl methyl phosphonate (DMMP) ...In this study, a series of flame-retardant polyisocyanurate-polyurethane (PIR-PUR) foams were prepared using various concentrations (0-25% by weight) of expandable graphite (EG) and dimethyl methyl phosphonate (DMMP) (0-7% by weight). The effect of these additives on the properties of the PIR-PUR foams, including physico-mechanical, morphological, flame retardancy, and thermal stability, was studied. Increasing amounts of EG in the PIR-PUR foam caused a significant drop in the compression strength. However, DMMP caused the mechanical properties of PIR-PUR foam to improve compared to foam filled with EG alone. The flame retardancy of PIR-PUR foams containing both EG and DMMP was enhanced significantly compared to EG filled foams. Thermogravimetric analysis (TGA) indicated that EG enhances the thermal stability of PIR-PUR foams but that DMMP decreased it. The morphology of the residual char provided conclusive evidence for the weak thermal stability of foams filled with DMMP.展开更多
The method of synthesis of trifuntional oligoetherols with carbazole ring from 9-(2,3-epoxypropyl)carbazole and die- thanolamine and oxiranes like ethylene and propylene oxide was presented. Structure and some physico...The method of synthesis of trifuntional oligoetherols with carbazole ring from 9-(2,3-epoxypropyl)carbazole and die- thanolamine and oxiranes like ethylene and propylene oxide was presented. Structure and some physicochemical prope- rties of the products were described. The oligoetherols were demonstrated as good substrates for synthesis of polyure- thane foams of enhanced thermal resistance. It has been found that the obtained foams are rigid at room temperature and their apparent density was 34 kg/m3- 44 kg/m3. The water uptake was low, maximum to 10.5 mass%. Dynamic thermal analysis of this foams showed that 5% mass loss starts at 200?C - 220?C, while temperature of 50% mass loss was 340?C - 370?C. Concomitantly the increase of compression strength was observed.展开更多
Rigid polyurethane foams were fabricated with five kinds of liquefied sugarcane bagasse polyols (LBP). The foams derived from sugarcane bagasse were investigated by thermogravimetric analysis (TGA), and the thermal de...Rigid polyurethane foams were fabricated with five kinds of liquefied sugarcane bagasse polyols (LBP). The foams derived from sugarcane bagasse were investigated by thermogravimetric analysis (TGA), and the thermal degradation data were analyzed using the Coast-Redfern method and Ozawa method to obtain the reaction order and activation energy. The results indicate that the sugarcane bagasse-foams exhibit an excellent heat-resistant property, whereas their pyrolysis procedures are quite complicated. The reaction as first order only takes place from 250 to 400 ℃, and the pyrolysis activation energies vary from 20 to 140 kJ/mol during the whole pyrolysis process.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.12221002,12102233)。
文摘In recent years,explosion shock wave has been considered as a signature injury of the current military conflicts.Although strong shock wave is lethal to the human body,weak shock wave can cause many more lasting consequences.To investigate the protection ability and characteristics of flexible materials and structures under weak shock wave loading,the blast wave produced by TNT explosive is loaded on the polyurethane foam with the density of 200.0 kg/m3(F-200)and 400.0 kg/m3(F-400),polyurea with the density of 1100.0 kg/m^(3)(P-1100)and structures composed of the two materials,which are intended for individual protection.Experimental results indicate that the shock wave is attenuated to weak pressure disturbance after interacting with the flexible materials which are not damaged.The shock wave protective capability of single-layer materials is dependent on their thickness,density and microscopic characteristics.The overpressure,maximum pressure rise rate and impulse of transmitted wave decrease exponentially with increase in sample thickness.For the same thickness,F-400 provides better protective capability than F-200 while P-1100 shows the best protective capability among the three materials.In this study,as the materials are not destroyed,F-200 with a thickness more than10.0 mm,F-400 with a thickness more than 4.0 mm,and P-1100 with a thickness more than 1.0 mm can attenuate the overpressure amplitude more than 90.0%.Further,multi-layer flexible composites are designed.Different layer layouts of designed structures and layer thickness of the single-layer materials can affect the protective performance.Within the research range,the structure in which polyurea is placed on the impact side shows the optimal shock wave protective performance,and the thicknesses of polyurea and polyurethane foam are 1.0 mm and 4.0 mm respectively.The overpressure attenuation rate reached maximum value of 93.3%and impulse attenuation capacity of this structure are better than those of single-layer polyurea and polyurethane foam with higher areal density.
基金financial support from National Natural Science Foundation of China(Grant No.12172325)。
文摘Porous materials are widely used in the field of protection because of their excellent energy absorption characteristics.In this work,a series of polyurethane microscopic models are established and the effect of porosity on the shock waves is studied with classical molecular dynamics simulations.Firstly,shock Hugoniot relations for different porosities are obtained,which compare well with the experimental data.The pores collapse and form local stress wave,which results in the complex multi-wave structure of the shock wave.The microstructure analysis shows that the local stress increases and the local velocity decreases gradually during the process of pore collapse to complete compaction.Finally,it leads to stress relaxation and velocity homogenization.The shock stress peaks can be fitted with two exponential functions,and the amplitude of attenuation coefficient decreases with the increase of density.Besides,the pore collapse under shock or non-shock are discussed by the entropy increase rate of the system.The energy is dissipated mainly through the multiple interactions of the waves under shock.The energy is dissipated mainly by the friction between atoms under non-shock.
基金funded by projects“Smart Materials,Photonics,Technologies and Engineering Ecosystem(MOTE)”(Contract No.VPP-EM-FOTONIKA-2022/1-0001)“Bio-Based Cryogenic Insulation for Aerospace Application(BioSpace)”(Contract No.4000135271/21/NL/SC).
文摘Cryogenic insulation material rigid polyurethane(PU)foams were developed using bio-based and recycled feedstock.Polyols obtained from tall oil fatty acids produced as a side stream of wood biomass pulping and recycled polyethylene terephthalate were used to develop rigid PU foam formulations.The 4th generation physical blowing agents with low global warming potential and low ozone depletion potential were used to develop rigid PU foam cryogenic insulation with excellent mechanical and thermal properties.Obtained rigid PU foams had a thermal conductivity coefficient as low as 0.0171 W/m·K and an apparent density of 37-40 kg/m^(3).The developed rigid PU foams had anisotropic compression strength properties,which were higher parallel to the foaming direction.Moreover,the compression strength was also influenced by the type of applied bio-based polyol.The bio-based polyols with higher OH group functionality delivered higher crosslinking density of polymer matrix;thus,the mechanical properties were also higher.The mechanical strength of the foams increased when materials were tested at liquid nitrogen temperature due to the stiffening of the polymer matrix.The thermal properties of the developed materials were determined using differential scanning calorimetry,dynamic mechanical analysis,and thermogravimetric analysis methods.Lastly,the developed rigid PU foams had good adhesion to the aluminium substrate before and after applying cyroshock and an excellent safety coefficient of 4-5.Rigid PU foams developed using Solstice LBA delivered adhesion strength of~0.5 MPa and may be considered for application as cryogenic insulation in the aerospace industry.
文摘In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore size of 0.3 mm was investigated.The main factors affecting the deposition rate such as the solution composition,temperature,pH value and adding ultrasonic were explored.The results show that the optimum process conditions are CuSO4 16 g/L,HCHO 5 mL/L,NaKC4H4O6 30 g/L,Na2EDTA 20 g/L,K4Fe(CN)6 25 mg/L,pH value of 12.5-13.0 and temperature of 40-50℃.Under these technical conditions, the process has excellent bath stability.Adding ultrasonic on the process can elevate the deposition rate of copper by 20%-30%.The foam metal material with a porosity of 92.2%and a three-dimensional network structure,was fabricated by electro-deposition after the electroless copper plating.
基金Funded by the National Innovation Platform Open Fund(No.2017YJ163)
文摘Based on the mechanical properties and microstructure of polyurethane foam solidified material, a two-dimensional model of polyurethane foam solidified material was constructed. Polyurethane foam was obtained by fully and uniformly mixing the two components. The research was carried out through the combination of experimental test and finite element simulation. The experimental results show that when the pore density is constant, the size of the bubble hole is an important factor affecting the mechanical properties of the model. The smaller the size of the bubble hole, the less likely it is to produce stress concentration inside the model, and the stronger the resistance to material deformation. Under the random distribution, the lower the density of the polyurethane cured material, the higher the probability of damage between the adjacent bubbles, which is not conducive to the stability of the material. The density of the cured material should not be lower than 199 kg/m^3.
基金This research was supported by National Key Research and Development Project(No.2017YFE0113200)National Natural Science Fund of China(Nos.51403004,U1833113).
文摘Biomass phytic acid has potential flame retardant value as the main form of phosphorus in plant seeds.In this study,phytate-based flame retardants aluminum phytate(PA-Al)and iron phytate(PA-Fe)were synthesized and characterized.Subsequently,they were introduced into rigid polyurethane foam(RPUF)as flame retardants by one-step water-blown method.The results indicated that RPUF/PA-Fe30 exhibited the highest char residue of 22.1 wt%,significantly higher than 12.4 wt%of RPUF.Cone calorimetry analysis showed that the total heat release(THR)of RPUF/PA-Al30 decreased by 17.0%and total smoke release(TSR)decreased by 22.0%compared with pure RPUF,which were the lowest,demonstrating a low fire risk and good smoke suppression.Thermogravimetric analysis-Fourier transform infrared spectrometer(TG-FTIR)implied the release intensity of flammable gases(hydrocarbons,esters)and toxic gases(isocyanate,CO,aromatic compounds,HCN)of composites was significantly reduced after the addition of PA-Fe.The analysis of char residue indicated that the RPUF composites formed a dense char layer with a high degree of graphitization after the addition of PA-Al/PA-Fe,endowing RPUF composites with excellent mass&heat transmission inhibition effect and fire resistance in the combustion process.
基金supported by the Yeungnam University research grant in 2017。
文摘Polyurethane foam dressings for dermal wounds were formulated with natural polyols in order to improve the foam characteristics and the release of 2 active agents,silver and asiaticoside(AS)as an antimicrobial agent and an herbal wound healing agent,respectively.The foam was instantly formed by interaction of polyols and diisocyanate.Hydroxypropyl methylcellulose,chitosan and sodium alginate were individually mixed with themain polyols,polypropylene glycol,in the formulation while the active componentswere impregnated into the obtained foam dressing sheets.Although the type and amount of the natural polyols slightly affected the pore size,water sorption-desorption profile and compression strength of the obtained foam sheets,a prominent effect was found in the release of both active components.Among natural polyols formulations,foam sheets with alginate showed the highest silver and AS release.Non-cytotoxicity of these foam sheets to human fibroblast cells was confirmed.Antimicrobial testing on four bacteria strains showed that 1mg/cm^2 silver in formulations with 6%of natural polyols and without natural polyols had sufficient content of the silver release with comparable inhibition zone and significantly larger zone than other formulations.In pig study,the foam dressing with 6%alginate,1mg/cm^2 silver and 5%AS could improve wound healing in both the percentage of the wound closure and histological parameters of the dermal wound without any dermatologic reactions.In conclusion,this innovative foam dressing had potential to be a good candidate for wound treatment.
基金Project supported by the National Key Research and Development Program of China(Grant No.2017YFA0204600)the National Natural Science Foundation of China(Grant No.51802352)the Fundamental Research Funds for the Central Universities of Central South University,China(Grant No.2018zzts355)
文摘The effect of a sandwiched cross-shaped metamaterial absorber(CMMA) on microwave absorption properties of the double-layered polyurethane foam absorber(PUFA) is investigated. Combining with the sandwiched CMMA, the bandwidth of -10-dB reflection loss for PUFA is broadened from 7.4 GHz to 9.1 GHz, which is attributed to the overlap of two absorption peaks originating from CMMA and PUFA, respectively. The values of the two absorption peaks located at 10.15 GHz and 14.7 GHz are -38.44 dB and -40.91 dB, respectively. Additionally, distribution of surface current,electromagnetic field and power loss density are introduced to investigate the absorption mechanism of the CMMA. The electromagnetic field distribution of the double-layered PUFA and the three-layered hybrid absorber are comparatively analyzed to ascertain the influence of CMMA. The results show that the proposed hybrid absorber can be applied to the anti-electromagnetic interference and stealth technology.
文摘In this study, polyurethane foam type thermoset polymerizing, due to chemical reaction between its liquid ingredients, was tested as binder after solidifying and then a rock-like material mixing with a sandy silt type soil was prepared. The uniaxial compressive strengths(UCSs) of polyurethane foam reinforced soil specimens were determined for different polyurethane ratios in the mixture. Additionally,a series of tests on slake durability, impact value, freezingethawing resistance, and abrasion resistance of polyurethane reinforced soil(PRS) mixture was conducted. The UCS values over 3 MPa were measured from the PRS specimens. The testing results showed that treated soil can economically become a desirable rock-like material in terms of slake durability and resistances against freezingethawing, impact effect and abrasion. As another characteristic of the rock-like material made with polyurethane foam,unit volume weight was found to be quite lower than those of natural rock materials.
基金This project was supported by the National Natural Science Foundation of China(No.20274053).
文摘CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. They may find wide applications in many fields.
文摘The production cost of flexible polyurethane foam is significantly dependent on the cost of polyol, which constitute the largest percentage of materials used in foam production with the characteracterics to induce superior mechanical properties. Suitable fillers that are relatively cheap can be introduced in the foam matrix as replacement for polyol. However, certain compositions of filler have deleterious effect on some relevant mechanical properties of the foam. This paper investigates the effect of CaCO3 filler in flexible polyurethane foam matrix for the dual purposes of achieving sustained mechanical properties and reduction in production cost. The optimum CaCO3 composition was found to be 20 wt % representing a concomitant 18.54% reduction in cost of production.
基金The key project of "11th Five-Year Plan" in Heilongjiang Province (No. GB06B501-3)
文摘The two kinds of rigid polyurethane(PU) foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight.The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams.The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples.The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently.Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples.The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.
基金Funded by Key Project of International Joint Research of National Natural Science Foundation of China(No.51320105004)
文摘A reconstruction method is proposed for the polyurethane foam and then a complete numerical method is developed to predict the effective thermal conductivity of the polyurethane foam. The finite volume method is applied to solve the 2D heterogeneous pure conduction. The lattice Boltzmann method is adopted to solve the 1D homogenous radiative transfer equation rather than Rosseland approximation equation. The lattice Boltzmann method is then adopted to solve 1D homogeneous conduction-radiation energy transport equation considering the combined effect of conduction and radiation. To validate the accuracy of the present method, the hot disk method is adopted to measure the effective thermal conductivity of the polyurethane foams at different temperature. The numerical results agree well with the experimental data. Then, the influences of temperature, porosity and cell size on the effective thermal conductivity of the polyurethane foam are investigated. The results show that the effective thermal conductivity of the polyurethane foams increases with temperature; and the effective thermal conductivity of the polyurethane foams decreases with increasing porosity while increases with the cell size.
文摘Effect of different chemicals and additives used in producing polyester foam was investigated. Reference samples were produced from polyol, toluene di isocyanate (TDI), amine stannous octoate distil water, and silicone oil using laboratory mix formulation based on 500 g polyether based polyol. Other samples were produced by consecutively varying the content of all the additives with the exception of polyol. Standard sample dimensions for density test, indentation test, compression set test, tensile strength and elongation tests were produced from the samples. The various tests were carried out on the samples using the ASTM-D3574 standards. It was observed that the degree of indentation affects the value of indentation hardness and increasing the percentage content of TDI results in acceptable compression set value for the polyester samples. It was concluded that Holding all other parameters constant, reducing the water content and increasing the TDI content will yield polyester foam of optimum properties.
文摘This article deals with the study of the viscoelastic and thermal properties of polyurethane (PU) rigid foamsfrom biobased and recycled components. Rapeseed oil (RO) and recycled poly(ethylene terephthalate)(PET) were used to synthesize PU polyols. Addition of adipic acid (ADA) to polyol resulted in improvedthermal and viscoelastic properties of foam materials. ADA content was varied from 1 to 6 wt%. Results ofthe dynamic mechanical spectra indicate an increase of the storage modulus E′ and the loss modulus E″ inthe whole temperature range for specimens with higher loading of ADA. In addition, damping factor shiftedto higher temperatures, but damping intensity remained almost unaffected by the compositions. Scanningelectron microscopy of the foams’ cross sections testified that the average cells’ size of 110 mm was unaffectedby the ADA content in polyol.
文摘Advanced wound dressings are replaced traditional dressings in order to provide appropriate environment for healing and also to promote cell migration[1].The key characteristics of wound dressings are non-toxic,highly absorbed,air permeable,biocompatible and have good mechanical properties[2].Due to providing moist environment and also protecting maceration at the wound edge area,foam dressings are used in various clinical applications[3].They are mostly prepared from polyurethane between polyols and isocyanate polymerization.
文摘Rigid polyurethane foam is found virtually everywhere in our modern world and is used in sound and thermal insulation applications such as refrigerators, insulated buildings, thermosets. Organometallic compounds are used as polyurethane catalysts since they are very highly selective towards the isocyanate-polyol reaction. Also, amine catalysts are used to balance both the gelling reaction and the gas-forming or foaming reaction responsible for foam formation. In this work, the effect of a tin octoate catalyst on the mechanical properties and morphology of polyurethane foam were investigated. Also, the thermal conductivity and sound absorption coefficient for polyurethane foam mortar formulations were measured. The morphological properties of polyurethane foam were investigated using scanning electron microscope to determine the influence of varying the concentration of tin octoate. It was clear from the results that polyurethane foam has good thermal and sound insulation capabilities.
基金supported by the State Key Program of Coal Joint Funds of National Natural Science Foundation of China (No.51134020)the Natural Science Foundation of Shandong Province(No. ZR2011EL036)the High School Science & Technology Fund Planning Project of Shandong Province (No. JIILD53)
文摘In this study, a series of flame-retardant polyisocyanurate-polyurethane (PIR-PUR) foams were prepared using various concentrations (0-25% by weight) of expandable graphite (EG) and dimethyl methyl phosphonate (DMMP) (0-7% by weight). The effect of these additives on the properties of the PIR-PUR foams, including physico-mechanical, morphological, flame retardancy, and thermal stability, was studied. Increasing amounts of EG in the PIR-PUR foam caused a significant drop in the compression strength. However, DMMP caused the mechanical properties of PIR-PUR foam to improve compared to foam filled with EG alone. The flame retardancy of PIR-PUR foams containing both EG and DMMP was enhanced significantly compared to EG filled foams. Thermogravimetric analysis (TGA) indicated that EG enhances the thermal stability of PIR-PUR foams but that DMMP decreased it. The morphology of the residual char provided conclusive evidence for the weak thermal stability of foams filled with DMMP.
文摘The method of synthesis of trifuntional oligoetherols with carbazole ring from 9-(2,3-epoxypropyl)carbazole and die- thanolamine and oxiranes like ethylene and propylene oxide was presented. Structure and some physicochemical prope- rties of the products were described. The oligoetherols were demonstrated as good substrates for synthesis of polyure- thane foams of enhanced thermal resistance. It has been found that the obtained foams are rigid at room temperature and their apparent density was 34 kg/m3- 44 kg/m3. The water uptake was low, maximum to 10.5 mass%. Dynamic thermal analysis of this foams showed that 5% mass loss starts at 200?C - 220?C, while temperature of 50% mass loss was 340?C - 370?C. Concomitantly the increase of compression strength was observed.
基金Funded by Guangdong Provincial Natural Science Foundation (No.E06200692)Guangdong Provincial Scientific and Technological Project(No. 2006A20401001)
文摘Rigid polyurethane foams were fabricated with five kinds of liquefied sugarcane bagasse polyols (LBP). The foams derived from sugarcane bagasse were investigated by thermogravimetric analysis (TGA), and the thermal degradation data were analyzed using the Coast-Redfern method and Ozawa method to obtain the reaction order and activation energy. The results indicate that the sugarcane bagasse-foams exhibit an excellent heat-resistant property, whereas their pyrolysis procedures are quite complicated. The reaction as first order only takes place from 250 to 400 ℃, and the pyrolysis activation energies vary from 20 to 140 kJ/mol during the whole pyrolysis process.
