An innovative approach based on water environmental capacity for non-point source NPS pollution removal rate estimation was discussed by using both univariate and multivariate data analysis.Taking Shenzhen city as the...An innovative approach based on water environmental capacity for non-point source NPS pollution removal rate estimation was discussed by using both univariate and multivariate data analysis.Taking Shenzhen city as the study case a 67% to 74% NPS pollutant load removal rate can lead to meeting the chemical oxygen demand COD pollution control target for most watersheds.In contrast it is hardly to achieve the ammonia nitrogen NH4-N total phosphorus TP and biological oxygen demand BOD5 pollution control target by simply removing NPS pollutants. This highlights that the pollution control strategies should be taken according to different pollutant species and sources in different watersheds rather than one-size-fits-all .展开更多
The stress intensity factors and stress conditions of machining cracks are analyzed by fracture mechanics on the basis of honing characteristics and of brittle ceramic mechanical behavior.Because the honing incidental...The stress intensity factors and stress conditions of machining cracks are analyzed by fracture mechanics on the basis of honing characteristics and of brittle ceramic mechanical behavior.Because the honing incidental tensile stresses effectively decrease the critical grinding stresses and increase the stress intensity factors of machining cracks,the honing process can be carried out easily.The results show that honing can be an efficient machining method for brittle materials.展开更多
In the present study,a novel method of surface finish improvement is proposed using shot blasting of soda lime(SBSL)beads on the Mg-AZ31 alloy.The effect of the soda blasting process parameters,such as blast pressure,...In the present study,a novel method of surface finish improvement is proposed using shot blasting of soda lime(SBSL)beads on the Mg-AZ31 alloy.The effect of the soda blasting process parameters,such as blast pressure,stand-off distance,and blast duration,have been studied in-response of material removal rate(MRR)and surface roughness(SR)and corresponding statistical models have been obtained.The multi-objective optimization has also been performed to obtain parameters for maximum MRR and minimum SR.The corrosion behavior of the treated specimens has been performed to study their in-vitro biodegradability in simulated body fluid(SBF)for 1,3,7,10,15,and 21 days.The wettability study of the SBSL treated samples has been investigated using sessile drop methodology.Further,cell adhesion test has also been performed to study the biocompatibility characteristics of the SBSL treated samples using Huh7 liver cell lines.Based on obtained quantitative data as well as scanning electron microscopy analysis of treated samples,the SBSL treatment of the AZ31 alloy has been found highly useful in producing biocompatibility surfaces along with desirable morphological features.展开更多
The mechanical characters of CdZnTe crystal were investigated by nanoscratch tests, and the effects of mechanical anisotropy on the material removal rate and surface quality were studied by polishing tests. There is a...The mechanical characters of CdZnTe crystal were investigated by nanoscratch tests, and the effects of mechanical anisotropy on the material removal rate and surface quality were studied by polishing tests. There is a peak of frictional coefficient at the early stage of scratch, and increasing the vertical force will result in the increase of peak value correspondingly. The fluctuation phenomenon of frictional coefficient is generated at high vertical force. The lateral forces show the apparent twofold and threefold symmetries on （110） and （111） planes, respectively. To obtain high surface quality, low polishing pressure and hard direction （〈 T10 〉 directions on （110） plane and 〈 112 〉 directions on （111） plane） should be selected, and to achieve high material removal rate, high polishing pressure and soft direction （〈001〉 directions on （110） plane and 〈 121 〉 directions on （111） plane） should be selected.展开更多
[ Objective] The study aimed to discuss the removal rate of phosphorus by different constructed wetland substrates. [ Methed] Based on static experiments, we analyzed the removal rate and characteristics of phosphorus...[ Objective] The study aimed to discuss the removal rate of phosphorus by different constructed wetland substrates. [ Methed] Based on static experiments, we analyzed the removal rate and characteristics of phosphorus by different constructed wetland substrates like steel slag, cin- der slag, shale, boiler slag, soil and gravel. [ Result~ The maximum adsorption of phosphorus by various substrates showed as follows, steel slag 〉 cinder slag 〉 shale 〉 boiler slag 〉 soil 〉 gravel. When the initial concentration of phosphorus was 5 mg/L, the removal rate of phosphorus by the steel slag, cinder slag, shale, boiler slag, soil and gravel was 99.76%, 85.8%, 71.2%, 63.0%, 46.8% and 11.7% respectively. It is suggested that shale and boiler slag can be used as the substrate of subsurface-flow constructed wetlands; cinder slag can be chosen as a renewable sub- strate for intensifying phosphorus removal; steel slag could be used at the end of subsurface-flow constructed wetlands for treating TP in outflows. [Concluslon] The research could provide theoretical references for choosing a suitable substrate for constructed wetlands to remove phosphorus in future.展开更多
This article presents an Artificial Neural Network （ANN） architecture to model the Electrical Discharge Machining （EDM） process. It is aimed to develop the ANN model using an input-output pattern of raw data colle...This article presents an Artificial Neural Network （ANN） architecture to model the Electrical Discharge Machining （EDM） process. It is aimed to develop the ANN model using an input-output pattern of raw data collected from an experimental of EDM process, whereas several research objectives have been outlined such as experimenting machining material for selected gap current, identifying machining parameters for ANN variables and selecting appropriate size of data selection. The experimental data （input variables） of copper-electrode and steel-workpiece is based on a selected gap current where pulse on time, pulse off time and sparking frequency have been chosen at optimum value of Material Removal Rate （MRR）. In this paper, the result has significantly demonstrated that the ANN model is capable of predicting the MRR with low percentage prediction error when compared with the experimental result.展开更多
Ultrasonic-assisted chemical mechanical polishing(UA-CMP)can greatly improve the sapphire material removal and surface quality,but its polishing mechanism is still unclear.This paper proposed a novel model of material...Ultrasonic-assisted chemical mechanical polishing(UA-CMP)can greatly improve the sapphire material removal and surface quality,but its polishing mechanism is still unclear.This paper proposed a novel model of material removal rate(MRR)to explore the mechanism of sapphire UA-CMP.It contains two modes,namely two-body wear and abrasive-impact.Furthermore,the atomic force microscopy(AFM)in-situ study,computational fluid dynamics(CFD)simulation,and polishing experiments were conducted to verify the model and reveal the polishing mechanism.In the AFM in-situ studies,the tip scratched the reaction layer on the sapphire surface.The pit with a 0.22 nm depth is the evidence of two-body wear.The CFD simulation showed that abrasives could be driven by the ultrasonic vibration to impact the sapphire surface at high frequencies.The maximum total velocity and the air volume fraction(AVF)in the central area increased from 0.26 to 0.55 m/s and 20%to 49%,respectively,with the rising amplitudes of 1–3μm.However,the maximum total velocity rose slightly from 0.33 to 0.42 m/s,and the AVF was nearly unchanged under 40–80 r/min.It indicated that the ultrasonic energy has great effects on the abrasive-impact mode.The UA-CMP experimental results exhibited that there was 63.7%improvement in MRR when the polishing velocities rose from 40 to 80 r/min.The roughness of the polished sapphire surface was R_(a)=0.07 nm.It identified that the higher speed achieved greater MRR mainly through the two-body wear mode.This study is beneficial to further understanding the UA-CMP mechanism and promoting the development of UA-CMP technology.展开更多
The influences of the polishing slurry composition,such as the pH value,the abrasive size and its concentration,the dispersant and the oxidants,the rotational velocity of the polishing platen and the carrier and the p...The influences of the polishing slurry composition,such as the pH value,the abrasive size and its concentration,the dispersant and the oxidants,the rotational velocity of the polishing platen and the carrier and the polishing pressure,on the material removal rate of SiC crystal substrate（0001） Si and a（0001） C surface have been studied based on the alumina abrasive in chemical mechanical polishing（CMP）.The results proposed by our research here will provide a reference for developing the slurry,optimizing the process parameters,and investigating the material removal mechanism in the CMP of SiC crystal substrate.展开更多
Traditional five-axis tool path planning methods mostly focus on differential geometric characteristics between the cutter and the workpiece surface to increase the material removal rate(i.e.,by minimizing path length...Traditional five-axis tool path planning methods mostly focus on differential geometric characteristics between the cutter and the workpiece surface to increase the material removal rate(i.e.,by minimizing path length,improving curvature matching,maximizing local cutting width,etc.) . However,material removal rate is not only related to geometric conditions such as the local cutting width,but also constrained by feeding speed as well as the motion capacity of the five-axis machine. This research integrates machine tool kinematics and cutter-workpiece contact kinematics to present a general kinematical model for five-axis machining process. Major steps of the proposed method include:(1) to establish the forward kinematical relationship between the motion of the machine tool axes and the cutter contact point;(2) to establish a tool path optimization model for high material removal rate based on both differential geometrical property and the contact kinematics between the cutter and workpiece;(3) to convert cutter orientation and cutting direction optimization problem into a concave quadratic planning(QP) model. Tool path will finally be generated from the underlying optimal cutting direction field. Through solving the time-optimal trajectory generation problem and machining experiment,we demonstrate the validity and effectiveness of the proposed method.展开更多
Distribution forms of abrasives in the chemical mechanical polishing（CMP） process are analyzed based on experimental results.Then the relationships between the wafer,the abrasive and the polishing pad are analyzed b...Distribution forms of abrasives in the chemical mechanical polishing（CMP） process are analyzed based on experimental results.Then the relationships between the wafer,the abrasive and the polishing pad are analyzed based on kinematics and contact mechanics.According to the track length of abrasives on the wafer surface,the relationships between the material removal rate and the polishing velocity are obtained.The analysis results are in accord with the experimental results.The conclusion provides a theoretical guide for further understanding the material removal mechanism of wafers in CMP.展开更多
Based on the Preston equation, the mathematical model of the material removal rate （MRR）, aiming at a line-orbit chemical mechanical polisher, is established. The MRR and the material removal non-uniformity （MRNU）...Based on the Preston equation, the mathematical model of the material removal rate （MRR）, aiming at a line-orbit chemical mechanical polisher, is established. The MRR and the material removal non-uniformity （MRNU） are numerically calculated by MATLAB, and the effects of the reciprocating parameters on the MRR and the MRNU are discussed. It is shown that the smaller the inclination angle and the larger the amplitude, the higher the MRR and the lower the MRNU. The reciprocating speed of the carrier plays a minor role to improve the MRR and decrease the MRNU. The results provide a guide for the design of a polisher and the determination of a process in line-orbit chemical mechanical polishing.展开更多
Because the polishing of different materials is required in barrier chemical mechanical planariza- tion （CMP） processes, the development of a kind of barrier slurry with improved removal rate selectivity for Cu/barr...Because the polishing of different materials is required in barrier chemical mechanical planariza- tion （CMP） processes, the development of a kind of barrier slurry with improved removal rate selectivity for Cu/barrier/TEOS would reduce erosion and dishing defects on patterned Cu wafers. In this study, we developed a new benzotriazole-free barrier slurry named FA/O barrier slurry, containing 20 mL/L of the chelating agent FA/O, 5 mL/L surfactant, and a 1：5 concentration of abrasive particles. By controlling the polishing slurry ingredients, the removal rate of different materials could be controlled. For process integration considerations, the effect of the FA/O barrier slurry on the dielectric layer of the patterned Cu wafer was investigated. After CMP processing by the FA/O barrier slurry, the characteristics of the dielectric material were tested. The results showed that the dielectric characteristics met demands for industrial production. The current leakage was of pA scale. The resistance and capacitance were 2.4 k and 2.3 pF, respectively. The dishing and erosion defects were both below 30 nm in size. CMP-processed wafers using this barrier slurry could meet industrial production demands.展开更多
[Objective] The research aimed at optimizing protein removal method and condition of polysaccharide extracts from Phellinus Linteus and comparing the effects of two methods on protein removal.[Method] Free proteins in...[Objective] The research aimed at optimizing protein removal method and condition of polysaccharide extracts from Phellinus Linteus and comparing the effects of two methods on protein removal.[Method] Free proteins in polysaccharide from Phellinus Linteus were removed using Sevag method and TCA method.[Result] The TCA method was better than Sevag method,and the optimum protein removal condition was treated with 5% TCA for 30 min and for three times,under that condition,the protein removal rate attained 82% while the polysaccharide loss rate was only 10.8%.[Conclusion] The TCA method was a better way to remove proteins of polysaccharide from Phellinus Linteus.展开更多
Microwave was applied to roasting the zinc oxide fume obtained from fuming furnace for the removal of F and Cl. The effects of important parameters, such as roasting temperature, holding time and stirring speed, were ...Microwave was applied to roasting the zinc oxide fume obtained from fuming furnace for the removal of F and Cl. The effects of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The results show that the effects of roasting temperature and holding time on the removal rate of F and Cl are the most significant, and the effect of stirring speed is the second. The defluorination rate reaches 92.6% while the dechlorination rate reaches 90.2%, under the process conditions of roasting temperature of 700 °C, holding time of 80 min and stirring speed of 120 r/min. The results indicate that the removal of F and Cl from fuming furnace production of zinc oxide fumes using microwave roasting process is feasible and reliable.展开更多
In this paper, glasshouse experiments were conducted to determine the accumulation, distribution and transformation of DDTs and HCHs by maize under pot culture conditions. The culture soil was spiked with the organic ...In this paper, glasshouse experiments were conducted to determine the accumulation, distribution and transformation of DDTs and HCHs by maize under pot culture conditions. The culture soil was spiked with the organic pollutants and samples were collected in different durations. Analysis of the plants at harvest showed that the selected plant varied widely in their ability to remove and translo- cate DDTs and HCHs from the soil, the bioconcentration factor ranged from 0.004 to 0.027 for the shoot and from 0.036 to 0.097 for the roots, and the translocation factors were lower than 0.1 with variation between DDTs and HCHs, but no signifi- cant differences were observed. DDTs appeared to have accumulated by both pas- sive adsorption and active absorption, p,p＇-DDT and p,p＇-DDE were the major metabolite and the transformation was mediated by reductive dehalogenation, the affinity of the OCPs for lipids is one of the major factors affecting their uptake and translocation within the plants.展开更多
Through a series of experiments using denitrifying phosphorus-accumulating sludge in sequencing batch reactors （SBRs）, the variations of the intracellular polymers during the anaerobic phosphorus release process at ...Through a series of experiments using denitrifying phosphorus-accumulating sludge in sequencing batch reactors （SBRs）, the variations of the intracellular polymers during the anaerobic phosphorus release process at different pH values were compared, the probable reasons for different performances of phosphorus removal were examined, and system operations in a typical cycle were investigated. The results show that the phosphorus removal rate was positively correlated with pH values in a range of 6.5-8.5. When the pH value was 8.0, the anaerobic phosphorus release rate and anoxic phosphorus uptake rate of the activated sludge were 20.95 mg/（g, h） and 23.29 mg/（g, h）, respectively; the mass fraction of poly-13-hydroxybutyrate （PHB） increased to 62.87 mg/g under anaerobic conditions; the mass fraction of polyphosphate was 92.67 mg/g under anoxic conditions; and the effluent concentration of total phosphorus （TP） was 1.47 mg/L. With the increase of pH, the mass fraction of acetic acid and PHB also increased, and the absorption rate of acetic acid was equal to the disintegration rate of polyphosphate. When the pH value was above 8.0, biological phosphorus removal was achieved by chemical phosphorus precipitation, and the phosphorus removal rate decreased.展开更多
Applied Immobilized algae bacteria (ABI) to remove ammonia of freshwater aquaculture wastewater. Temperature (T),PH,light intensity (I),dissolved oxygen (DO) and filling rate five factors plays important role in the p...Applied Immobilized algae bacteria (ABI) to remove ammonia of freshwater aquaculture wastewater. Temperature (T),PH,light intensity (I),dissolved oxygen (DO) and filling rate five factors plays important role in the process of ammonia nitrogen removal ,related data between ammonia removal and five factors was received through multi-factor orthogonal test,and established relations model between the five factor and nitrogen removal. The results show that five-factors had significant effect on AR,and the best combinations for removing AR was temperature 30 ℃,pH=7.0,light intensity 6 000 lux,dissolved oxygen 5.0 mg/L and the fill rate 10%. According to the experimental data,equation model was proposed and coefficient of determination R2 =0.864 8,P<0.05. Samples T-test was done between the model predictions and the actual measured values.Test results showed that the significant difference of overall mean value sig. (2-tailed) was 0.978 (P>0.05),it Shows that had no significant difference between model predictions and the actual measured value,and model had a high degree of fitting.展开更多
In order to enhance the hydraulic loading rate （HLR） of a subsurface wastewater infiltration system （SWIS） used in treating domestic sewage, the intermittent operation mode was employed in the SWIS. The results sh...In order to enhance the hydraulic loading rate （HLR） of a subsurface wastewater infiltration system （SWIS） used in treating domestic sewage, the intermittent operation mode was employed in the SWIS. The results show that the intermittent operation mode contributes to the improvement of the HLR and the pollutant removal rate. When the wetting-drying ratio （RwD） was 1.0, the pollutant removal rate increased by （13.6 ± 0.3）% for NH3-N, （20.7 ± 1.1）% for TN, （18.6± 0.4）% for TP, （12.2 ± 0.5）% for BOD, （10.1 ± 0.3）% for COD, and （36.2 ± 1.2）% for SS, compared with pollutant removal rates under the continuous operation mode. The pollutant removal rate declined with the increase of the HLR. The effluent quality met The Reuse of Urban Recycling Water - Water Quality Standard for Scenic Environment Use （GB/T 18921-2002） even when the HLR was as high as 10 cm/d. Hydraulic conductivity, oxidation reduction potential （ORP）, the quantity of nitrifying bacteria, and the pollutant removal rate of NH3-N increased with the decrease of the RWD. For the pollutant removal rates of TP, BOD, and COD, there were no significant difference （p 〈 0.05） under different RwDS. The suggested RWD was 1.0. Relative contribution of the pretreatment and SWlS to the pollutant removal was examined, and more than 80% removal of NH3-N, TN, TP, COD, and BOD occurred in the SWIS.展开更多
A computational fluid dynamic （ CFD ） analysis of air movement and aerosol particle transport in a two-zone ventilated room with an inter-zonal opening is presented to study the impact of ventilation strategies and ...A computational fluid dynamic （ CFD ） analysis of air movement and aerosol particle transport in a two-zone ventilated room with an inter-zonal opening is presented to study the impact of ventilation strategies and size of the opening on indoor particle dispersion and concentration distribution. The comparisons of average particle concentrations in both zones between the computations and the experiments from the literature are generally satisfactory and acceptable. The combined effects of sizes of the opening and the inlet and outlet locations （three different strategies） are simulated and discussed. The results show that ventilation strategy and size of the opening influence the particle removal rate in zone 1. The removal rate is decreased when the air supply system is changed from the tap-inlet to the bottom-inlet configuration. The top-inlet system obtains a better particle deposition in zone I than the bottom-inlet configuration. However, the particle concentration at breathing level is lower for bottomsupply system than for top-supply. Decreasing the size of interzonal opening increases the particle deposition rate in zone 1 only for the top.supply system, especially for coarse particles.展开更多
[ Objective] The study aimed to discuss the feasibility and optimal conditions of removing ammonia nitrogen by using microwave coupled with active carbon. [ Method ] In the study, a novel process, microwave radiation ...[ Objective] The study aimed to discuss the feasibility and optimal conditions of removing ammonia nitrogen by using microwave coupled with active carbon. [ Method ] In the study, a novel process, microwave radiation coupled with active carbon, was applied to remove ammonia nitro- gen from wastewater, and the influences of solution pH, air conditions, active carbon usage, microwave power and time on the removal effect of ammonia nitrogen were studied. [ Result] Microwave coupled with active carbon can remove ammonia nitrogen efficiently, and pumping air into the wastewater can also increase the removal rate of ammonia nitrogen to a certain extent. Higher pH, intensive microwave power and longer treating time could also increase the removal rate of ammonia nitrogen using microwave radiation coupled with active carbon, whereas the usage of active carbon contributed a small impact. It was proved that microwave coupled with active carbon was an effective method for the removal of ammonia ni- trogen from wastewater. Meanwhile, the orthogonal experiment results showed that the removal rate of ammonia nitrogen reached 92.5% under the optimal conditions, that is, the usage of active carbon was 0.5 g, pH = 11, microwave radiation power was 850 W, and microwave action time was 4 minutes. [ Conclusion] The research provided a new method to remove ammonia nitrogen from wastewater, namely microwave coupled with ac- tive carbon.展开更多
基金The National Science and Technology Major Project of China(No.2012ZX07301-001)the Shenzhen Environmental Research Project,China Postdoctoral Science Foundation(No.2013M530642)
文摘An innovative approach based on water environmental capacity for non-point source NPS pollution removal rate estimation was discussed by using both univariate and multivariate data analysis.Taking Shenzhen city as the study case a 67% to 74% NPS pollutant load removal rate can lead to meeting the chemical oxygen demand COD pollution control target for most watersheds.In contrast it is hardly to achieve the ammonia nitrogen NH4-N total phosphorus TP and biological oxygen demand BOD5 pollution control target by simply removing NPS pollutants. This highlights that the pollution control strategies should be taken according to different pollutant species and sources in different watersheds rather than one-size-fits-all .
文摘The stress intensity factors and stress conditions of machining cracks are analyzed by fracture mechanics on the basis of honing characteristics and of brittle ceramic mechanical behavior.Because the honing incidental tensile stresses effectively decrease the critical grinding stresses and increase the stress intensity factors of machining cracks,the honing process can be carried out easily.The results show that honing can be an efficient machining method for brittle materials.
文摘In the present study,a novel method of surface finish improvement is proposed using shot blasting of soda lime(SBSL)beads on the Mg-AZ31 alloy.The effect of the soda blasting process parameters,such as blast pressure,stand-off distance,and blast duration,have been studied in-response of material removal rate(MRR)and surface roughness(SR)and corresponding statistical models have been obtained.The multi-objective optimization has also been performed to obtain parameters for maximum MRR and minimum SR.The corrosion behavior of the treated specimens has been performed to study their in-vitro biodegradability in simulated body fluid(SBF)for 1,3,7,10,15,and 21 days.The wettability study of the SBSL treated samples has been investigated using sessile drop methodology.Further,cell adhesion test has also been performed to study the biocompatibility characteristics of the SBSL treated samples using Huh7 liver cell lines.Based on obtained quantitative data as well as scanning electron microscopy analysis of treated samples,the SBSL treatment of the AZ31 alloy has been found highly useful in producing biocompatibility surfaces along with desirable morphological features.
基金supported by the Key Project of the National Natural Science Foundation of China (No. 50535020)the Fund of the State Key Laboratory of Solidification Processing in Northwestern Polytechnical University (No. SKLSP200902)
文摘The mechanical characters of CdZnTe crystal were investigated by nanoscratch tests, and the effects of mechanical anisotropy on the material removal rate and surface quality were studied by polishing tests. There is a peak of frictional coefficient at the early stage of scratch, and increasing the vertical force will result in the increase of peak value correspondingly. The fluctuation phenomenon of frictional coefficient is generated at high vertical force. The lateral forces show the apparent twofold and threefold symmetries on （110） and （111） planes, respectively. To obtain high surface quality, low polishing pressure and hard direction （〈 T10 〉 directions on （110） plane and 〈 112 〉 directions on （111） plane） should be selected, and to achieve high material removal rate, high polishing pressure and soft direction （〈001〉 directions on （110） plane and 〈 121 〉 directions on （111） plane） should be selected.
基金Supported by National Natural Science Foundation of China(50278016)
文摘[ Objective] The study aimed to discuss the removal rate of phosphorus by different constructed wetland substrates. [ Methed] Based on static experiments, we analyzed the removal rate and characteristics of phosphorus by different constructed wetland substrates like steel slag, cin- der slag, shale, boiler slag, soil and gravel. [ Result~ The maximum adsorption of phosphorus by various substrates showed as follows, steel slag 〉 cinder slag 〉 shale 〉 boiler slag 〉 soil 〉 gravel. When the initial concentration of phosphorus was 5 mg/L, the removal rate of phosphorus by the steel slag, cinder slag, shale, boiler slag, soil and gravel was 99.76%, 85.8%, 71.2%, 63.0%, 46.8% and 11.7% respectively. It is suggested that shale and boiler slag can be used as the substrate of subsurface-flow constructed wetlands; cinder slag can be chosen as a renewable sub- strate for intensifying phosphorus removal; steel slag could be used at the end of subsurface-flow constructed wetlands for treating TP in outflows. [Concluslon] The research could provide theoretical references for choosing a suitable substrate for constructed wetlands to remove phosphorus in future.
文摘This article presents an Artificial Neural Network （ANN） architecture to model the Electrical Discharge Machining （EDM） process. It is aimed to develop the ANN model using an input-output pattern of raw data collected from an experimental of EDM process, whereas several research objectives have been outlined such as experimenting machining material for selected gap current, identifying machining parameters for ANN variables and selecting appropriate size of data selection. The experimental data （input variables） of copper-electrode and steel-workpiece is based on a selected gap current where pulse on time, pulse off time and sparking frequency have been chosen at optimum value of Material Removal Rate （MRR）. In this paper, the result has significantly demonstrated that the ANN model is capable of predicting the MRR with low percentage prediction error when compared with the experimental result.
基金This work was supported by the National Natural Science Foundation of China(Nos.51865030 and 52165025).
文摘Ultrasonic-assisted chemical mechanical polishing(UA-CMP)can greatly improve the sapphire material removal and surface quality,but its polishing mechanism is still unclear.This paper proposed a novel model of material removal rate(MRR)to explore the mechanism of sapphire UA-CMP.It contains two modes,namely two-body wear and abrasive-impact.Furthermore,the atomic force microscopy(AFM)in-situ study,computational fluid dynamics(CFD)simulation,and polishing experiments were conducted to verify the model and reveal the polishing mechanism.In the AFM in-situ studies,the tip scratched the reaction layer on the sapphire surface.The pit with a 0.22 nm depth is the evidence of two-body wear.The CFD simulation showed that abrasives could be driven by the ultrasonic vibration to impact the sapphire surface at high frequencies.The maximum total velocity and the air volume fraction(AVF)in the central area increased from 0.26 to 0.55 m/s and 20%to 49%,respectively,with the rising amplitudes of 1–3μm.However,the maximum total velocity rose slightly from 0.33 to 0.42 m/s,and the AVF was nearly unchanged under 40–80 r/min.It indicated that the ultrasonic energy has great effects on the abrasive-impact mode.The UA-CMP experimental results exhibited that there was 63.7%improvement in MRR when the polishing velocities rose from 40 to 80 r/min.The roughness of the polished sapphire surface was R_(a)=0.07 nm.It identified that the higher speed achieved greater MRR mainly through the two-body wear mode.This study is beneficial to further understanding the UA-CMP mechanism and promoting the development of UA-CMP technology.
基金supported by the National Natural Science Foundation of China(No.51075125)the Key Scientific Research Program of Economic and Social Development of Xinxiang City(No.S10004)the Science and Technology Innovation Program of Henan Institute of Science and Technology
文摘The influences of the polishing slurry composition,such as the pH value,the abrasive size and its concentration,the dispersant and the oxidants,the rotational velocity of the polishing platen and the carrier and the polishing pressure,on the material removal rate of SiC crystal substrate（0001） Si and a（0001） C surface have been studied based on the alumina abrasive in chemical mechanical polishing（CMP）.The results proposed by our research here will provide a reference for developing the slurry,optimizing the process parameters,and investigating the material removal mechanism in the CMP of SiC crystal substrate.
基金supported by the National Basic Research Program of China ("973" Program) (Grant No. 2011CB706800)the National Natural Science Foundation of China (Grant No. 50835004)the National Funds for Distinguished Young Scientists of China (Grant No. 51025518)
文摘Traditional five-axis tool path planning methods mostly focus on differential geometric characteristics between the cutter and the workpiece surface to increase the material removal rate(i.e.,by minimizing path length,improving curvature matching,maximizing local cutting width,etc.) . However,material removal rate is not only related to geometric conditions such as the local cutting width,but also constrained by feeding speed as well as the motion capacity of the five-axis machine. This research integrates machine tool kinematics and cutter-workpiece contact kinematics to present a general kinematical model for five-axis machining process. Major steps of the proposed method include:(1) to establish the forward kinematical relationship between the motion of the machine tool axes and the cutter contact point;(2) to establish a tool path optimization model for high material removal rate based on both differential geometrical property and the contact kinematics between the cutter and workpiece;(3) to convert cutter orientation and cutting direction optimization problem into a concave quadratic planning(QP) model. Tool path will finally be generated from the underlying optimal cutting direction field. Through solving the time-optimal trajectory generation problem and machining experiment,we demonstrate the validity and effectiveness of the proposed method.
基金supported by the Major Project of National Natural Science Foundation of China(No.50390061)the Key Project of Science and Technology R & D Program of Henan Province,China(No.102102210405)+2 种基金the Research Project Program of Natural Science of the Education Department of Henan Province,China(No.2009A460004)the Scientific Research Foundation of Henan Institute of Science and Technology for High Level Scholarthe Science and Technology Innovation Program of Henan Institute of Science and Technology.
文摘Distribution forms of abrasives in the chemical mechanical polishing（CMP） process are analyzed based on experimental results.Then the relationships between the wafer,the abrasive and the polishing pad are analyzed based on kinematics and contact mechanics.According to the track length of abrasives on the wafer surface,the relationships between the material removal rate and the polishing velocity are obtained.The analysis results are in accord with the experimental results.The conclusion provides a theoretical guide for further understanding the material removal mechanism of wafers in CMP.
基金Project supported by the National Science & Technology Major Project of China(No.2009ZX02011)the Excellent Talent Support Plan for College of Dalian Province,China(No.2008RC58)
文摘Based on the Preston equation, the mathematical model of the material removal rate （MRR）, aiming at a line-orbit chemical mechanical polisher, is established. The MRR and the material removal non-uniformity （MRNU） are numerically calculated by MATLAB, and the effects of the reciprocating parameters on the MRR and the MRNU are discussed. It is shown that the smaller the inclination angle and the larger the amplitude, the higher the MRR and the lower the MRNU. The reciprocating speed of the carrier plays a minor role to improve the MRR and decrease the MRNU. The results provide a guide for the design of a polisher and the determination of a process in line-orbit chemical mechanical polishing.
基金supported by the Special Project Items No.2 in National Long-Term Technology Development Plan(No.2009ZX02308)the Natural Science Foundation of Hebei Province(No.F2012202094)the Doctoral Program Foundation of Xinjiang Normal University Plan(No.XJNUBS1226)
文摘Because the polishing of different materials is required in barrier chemical mechanical planariza- tion （CMP） processes, the development of a kind of barrier slurry with improved removal rate selectivity for Cu/barrier/TEOS would reduce erosion and dishing defects on patterned Cu wafers. In this study, we developed a new benzotriazole-free barrier slurry named FA/O barrier slurry, containing 20 mL/L of the chelating agent FA/O, 5 mL/L surfactant, and a 1：5 concentration of abrasive particles. By controlling the polishing slurry ingredients, the removal rate of different materials could be controlled. For process integration considerations, the effect of the FA/O barrier slurry on the dielectric layer of the patterned Cu wafer was investigated. After CMP processing by the FA/O barrier slurry, the characteristics of the dielectric material were tested. The results showed that the dielectric characteristics met demands for industrial production. The current leakage was of pA scale. The resistance and capacitance were 2.4 k and 2.3 pF, respectively. The dishing and erosion defects were both below 30 nm in size. CMP-processed wafers using this barrier slurry could meet industrial production demands.
基金Supported by Youth Fund Project in Sichuan Province(2008ZQ026-072)Support Science and Technology Project of Sichuan Province(2008FZ0157)~~
文摘[Objective] The research aimed at optimizing protein removal method and condition of polysaccharide extracts from Phellinus Linteus and comparing the effects of two methods on protein removal.[Method] Free proteins in polysaccharide from Phellinus Linteus were removed using Sevag method and TCA method.[Result] The TCA method was better than Sevag method,and the optimum protein removal condition was treated with 5% TCA for 30 min and for three times,under that condition,the protein removal rate attained 82% while the polysaccharide loss rate was only 10.8%.[Conclusion] The TCA method was a better way to remove proteins of polysaccharide from Phellinus Linteus.
基金Project(51104073)supported by the National Natural Science Foundation of ChinaProject(2013AA064003)supported by the High-tech Research and Development Program of China+1 种基金Project(2014CB643404)supported by the National Basic Research Program of ChinaProject(2012HB008)supported by Yunnan Province Young Academic Technology Leader Reserve Talents,China
文摘Microwave was applied to roasting the zinc oxide fume obtained from fuming furnace for the removal of F and Cl. The effects of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The results show that the effects of roasting temperature and holding time on the removal rate of F and Cl are the most significant, and the effect of stirring speed is the second. The defluorination rate reaches 92.6% while the dechlorination rate reaches 90.2%, under the process conditions of roasting temperature of 700 °C, holding time of 80 min and stirring speed of 120 r/min. The results indicate that the removal of F and Cl from fuming furnace production of zinc oxide fumes using microwave roasting process is feasible and reliable.
基金Supported by the Youth Innovation Fund of Inner Mongolia Academy of Agricultural and Animal Husbandry Sciences(2009QNJJN01)the Science and Technology Innovation Fund of Inner Mongolia(2011CXJJN01)the Application Technology Research and Development Program from Department of Science and Technology of Inner Mongolia(20110516)~~
文摘In this paper, glasshouse experiments were conducted to determine the accumulation, distribution and transformation of DDTs and HCHs by maize under pot culture conditions. The culture soil was spiked with the organic pollutants and samples were collected in different durations. Analysis of the plants at harvest showed that the selected plant varied widely in their ability to remove and translo- cate DDTs and HCHs from the soil, the bioconcentration factor ranged from 0.004 to 0.027 for the shoot and from 0.036 to 0.097 for the roots, and the translocation factors were lower than 0.1 with variation between DDTs and HCHs, but no signifi- cant differences were observed. DDTs appeared to have accumulated by both pas- sive adsorption and active absorption, p,p＇-DDT and p,p＇-DDE were the major metabolite and the transformation was mediated by reductive dehalogenation, the affinity of the OCPs for lipids is one of the major factors affecting their uptake and translocation within the plants.
基金supported by the Research Program of the Liaoning Educational Committee(Grant No.LJZ2016014)the Natural Science Foundation of Liaoning Province(Grant No.201501069)+1 种基金the Research Program of the Ministry of Housing and Urban-Rural Development(Grant No.2015-K7-007)the National Natural Science Foundation of China(Grants No.51776131 and 51678375)
文摘Through a series of experiments using denitrifying phosphorus-accumulating sludge in sequencing batch reactors （SBRs）, the variations of the intracellular polymers during the anaerobic phosphorus release process at different pH values were compared, the probable reasons for different performances of phosphorus removal were examined, and system operations in a typical cycle were investigated. The results show that the phosphorus removal rate was positively correlated with pH values in a range of 6.5-8.5. When the pH value was 8.0, the anaerobic phosphorus release rate and anoxic phosphorus uptake rate of the activated sludge were 20.95 mg/（g, h） and 23.29 mg/（g, h）, respectively; the mass fraction of poly-13-hydroxybutyrate （PHB） increased to 62.87 mg/g under anaerobic conditions; the mass fraction of polyphosphate was 92.67 mg/g under anoxic conditions; and the effluent concentration of total phosphorus （TP） was 1.47 mg/L. With the increase of pH, the mass fraction of acetic acid and PHB also increased, and the absorption rate of acetic acid was equal to the disintegration rate of polyphosphate. When the pH value was above 8.0, biological phosphorus removal was achieved by chemical phosphorus precipitation, and the phosphorus removal rate decreased.
基金Supported by the National Natural Science Foundation of China(No.30972260)~~
文摘Applied Immobilized algae bacteria (ABI) to remove ammonia of freshwater aquaculture wastewater. Temperature (T),PH,light intensity (I),dissolved oxygen (DO) and filling rate five factors plays important role in the process of ammonia nitrogen removal ,related data between ammonia removal and five factors was received through multi-factor orthogonal test,and established relations model between the five factor and nitrogen removal. The results show that five-factors had significant effect on AR,and the best combinations for removing AR was temperature 30 ℃,pH=7.0,light intensity 6 000 lux,dissolved oxygen 5.0 mg/L and the fill rate 10%. According to the experimental data,equation model was proposed and coefficient of determination R2 =0.864 8,P<0.05. Samples T-test was done between the model predictions and the actual measured values.Test results showed that the significant difference of overall mean value sig. (2-tailed) was 0.978 (P>0.05),it Shows that had no significant difference between model predictions and the actual measured value,and model had a high degree of fitting.
基金supported by the National Natural Science Foundation of China(Grant No.51108275)the Program for Liaoning Excellent Talents in Universities(LNET)(Grant No.LJQ2012101)+2 种基金the Program for New Century Excellent Talents in Universities(Grant No.NCET-11-1012)the Science and Technology Program of Liaoning Province(Grants No.2011229002 and2013229012)the Basic Science Research Fund in Northeastern University(Grants No.N130501001 and N140105003)
文摘In order to enhance the hydraulic loading rate （HLR） of a subsurface wastewater infiltration system （SWIS） used in treating domestic sewage, the intermittent operation mode was employed in the SWIS. The results show that the intermittent operation mode contributes to the improvement of the HLR and the pollutant removal rate. When the wetting-drying ratio （RwD） was 1.0, the pollutant removal rate increased by （13.6 ± 0.3）% for NH3-N, （20.7 ± 1.1）% for TN, （18.6± 0.4）% for TP, （12.2 ± 0.5）% for BOD, （10.1 ± 0.3）% for COD, and （36.2 ± 1.2）% for SS, compared with pollutant removal rates under the continuous operation mode. The pollutant removal rate declined with the increase of the HLR. The effluent quality met The Reuse of Urban Recycling Water - Water Quality Standard for Scenic Environment Use （GB/T 18921-2002） even when the HLR was as high as 10 cm/d. Hydraulic conductivity, oxidation reduction potential （ORP）, the quantity of nitrifying bacteria, and the pollutant removal rate of NH3-N increased with the decrease of the RWD. For the pollutant removal rates of TP, BOD, and COD, there were no significant difference （p 〈 0.05） under different RwDS. The suggested RWD was 1.0. Relative contribution of the pretreatment and SWlS to the pollutant removal was examined, and more than 80% removal of NH3-N, TN, TP, COD, and BOD occurred in the SWIS.
基金National Natural Science Foundation of China (No.40975012)
文摘A computational fluid dynamic （ CFD ） analysis of air movement and aerosol particle transport in a two-zone ventilated room with an inter-zonal opening is presented to study the impact of ventilation strategies and size of the opening on indoor particle dispersion and concentration distribution. The comparisons of average particle concentrations in both zones between the computations and the experiments from the literature are generally satisfactory and acceptable. The combined effects of sizes of the opening and the inlet and outlet locations （three different strategies） are simulated and discussed. The results show that ventilation strategy and size of the opening influence the particle removal rate in zone 1. The removal rate is decreased when the air supply system is changed from the tap-inlet to the bottom-inlet configuration. The top-inlet system obtains a better particle deposition in zone I than the bottom-inlet configuration. However, the particle concentration at breathing level is lower for bottomsupply system than for top-supply. Decreasing the size of interzonal opening increases the particle deposition rate in zone 1 only for the top.supply system, especially for coarse particles.
基金Supported by National Key Project of Science and Technology of Water Pollution Control and Management(2009ZX07212-001-04)
文摘[ Objective] The study aimed to discuss the feasibility and optimal conditions of removing ammonia nitrogen by using microwave coupled with active carbon. [ Method ] In the study, a novel process, microwave radiation coupled with active carbon, was applied to remove ammonia nitro- gen from wastewater, and the influences of solution pH, air conditions, active carbon usage, microwave power and time on the removal effect of ammonia nitrogen were studied. [ Result] Microwave coupled with active carbon can remove ammonia nitrogen efficiently, and pumping air into the wastewater can also increase the removal rate of ammonia nitrogen to a certain extent. Higher pH, intensive microwave power and longer treating time could also increase the removal rate of ammonia nitrogen using microwave radiation coupled with active carbon, whereas the usage of active carbon contributed a small impact. It was proved that microwave coupled with active carbon was an effective method for the removal of ammonia ni- trogen from wastewater. Meanwhile, the orthogonal experiment results showed that the removal rate of ammonia nitrogen reached 92.5% under the optimal conditions, that is, the usage of active carbon was 0.5 g, pH = 11, microwave radiation power was 850 W, and microwave action time was 4 minutes. [ Conclusion] The research provided a new method to remove ammonia nitrogen from wastewater, namely microwave coupled with ac- tive carbon.
