When designing a solar power plant, it is much more important to avoid the shadow on the PV Panels. As the shadow falls on the PV Panels;it significantly reduces the generation of required power as planned and designe...When designing a solar power plant, it is much more important to avoid the shadow on the PV Panels. As the shadow falls on the PV Panels;it significantly reduces the generation of required power as planned and designed. This research paper and case study will help a lot to avoid shadow, especially when selecting inter-row spacing between the strings of solar power plants.展开更多
In monoculture, crop failure due to biotic or abiotic causes can result in partial or total output failure. The yield, socio-economic, and environmental effects of intercropping on the farmer and the environment as a ...In monoculture, crop failure due to biotic or abiotic causes can result in partial or total output failure. The yield, socio-economic, and environmental effects of intercropping on the farmer and the environment as a whole have not received much attention. There is a dearth of knowledge on the productivity of maize-groundnut intercrops in Ghana regarding the relative timing of planting and spatial arrangement of component crops. Therefore, the objective of the study was to determine the effects of spatial row arrangement and the time of planting intercrops on the productivity of groundnut under maize-groundnut intercropping. The 5 × 3 factorial field experiment was undertaken at the Miminaso community in the Ejura-Sekyedumase municipality of the Ashanti Region of Ghana during the 2020 cropping seasons. Treatments were evaluated in a Randomized Complete Block Design (RCBD) with three replicates. The levels of row arrangement of intercrops were: one row of maize and one row of groundnut (1M1G), one row of maize and two rows of groundnut (1M2G), two rows of maize and one row of groundnut (2M1G), two rows of maize and two rows of groundnut (2M2G), sole maize and sole groundnut (M/G). The levels of time of introducing groundnut included simultaneous planting of intercrops (0 WAP), planting groundnut one week after planting maize (1 WAP) and planting groundnut two weeks after planting maize (2 WAP). There were significant (P 0.05) treatment interactions for pod and seed yields of groundnut throughout the study. The highest groundnut pod yields of 1815.00 kg/ha and 2359.00 kg/ha were recorded by the 0WAP × 1M2G treatment in the major and minor seasons of 2020, respectively, while the highest groundnut seed yields of 741.00 kg/ha and 726.00 kg/ha were recorded in the major and minor rainy seasons of 2020 by 1WAP × G and 0WAP × G treatments, respectively. The highest seed yields of groundnut (404 kg/ha and 637 kg/ha for major and minor rainy seasons, respectively) were produced by 1WAP × 2M2G.展开更多
The ligand o-phenylenediamine (opda) and its oxidized form, o-benzoquinonediimine (bqdi), act as a fascinating candidate coordinating toward transition metal ions leading to the photochemical hydrogen production in ab...The ligand o-phenylenediamine (opda) and its oxidized form, o-benzoquinonediimine (bqdi), act as a fascinating candidate coordinating toward transition metal ions leading to the photochemical hydrogen production in absence of photosensitizers. Herein, we report the systematic study of the interaction between the oxidized form bqdi ligand, tris-(o-benzoquinonediimine) with divalent first-row transition metal series using DFT calculations. The lowest energy structures, bond length, binding energies, frontier molecular orbital analysis, natural bond orbitals, and global reactivity descriptor were calculated using B3LYP/6-311G(d,P) level of theory. The time dependent-DFT at the CAM-B3LYP/6-311+G(d,p) level of theory was applied to determine the electronic structures and the optical spectra. The theoretical binding trend of the divalent first-row transition metal series is decreasing as follows: Cu >Ti > V > Co > Ni > Fe > Cr > Zn >Mn. Among them, the binding potency of iron (II) by the bqdi ligand was not predominantly sturdy as compared to other first-row divalent transition metal ions. The origin of strong coordination with Fe(II) is attributed to its extra capability to induce covalent coordination of bqdi ligands. The complex exhibited two strong peaks at 370 nm and 452 nm, due to the HOMO-3 to LUMO+1 and HOMO-1 to LUMO transitions, respectively. Natural bond orbital analysis showed that the major interaction happens between the N lone pair electrons of the ligand with an anti-bonding orbital of metal ions, in which Ti showed the highest interaction energy than other metal ions. The present systemic DFT study of bqdi ligands with the first-row transition metals strongly encourages the future establishment of photochemical hydrogen production in absence of photosensitizers.展开更多
The declining Ogallala Aquifer beneath the Southern High Plains may necessitate dryland crop production and cotton (Gossypium hirsutum L.) is a well-adapted and potentially profitable alternative crop. The limited gro...The declining Ogallala Aquifer beneath the Southern High Plains may necessitate dryland crop production and cotton (Gossypium hirsutum L.) is a well-adapted and potentially profitable alternative crop. The limited growing season duration of the Texas Panhandle and southwestern Kansas, however, imposes significant production risk due to incomplete boll maturation. Emphasizing earlier boll production that is usually confined to sites on lower fruiting branches may reduce risk, but offsetting high planting densities are needed to maintain desirable lint yield. Our objectives were to quantify planting: 1) row width and 2) in-row spacing effects on growth, yield, and fiber quality of dryland cotton. Field tests of row widths from 0.25 to 0.76 m and plant densities with in-row spacing ranging from 0.075 to 0.15 m were conducted from 1999 to 2005 on a nearly level Pullman clay loam (fine, mixed, superactive, thermic Torrertic Paleustoll) managed in a wheat (Triticum aestivum L.), cotton, fallow (W-Ctn-F) rotation. To expand the basis of comparison, cotton growth and yields were simulated using GOSSYM and long-term (1958-2000) weather records from Bushland, TX, as input for all combinations of 0.38 or 0.76 m row widths and plant spacing of 0.075, 0.10 and 0.15 m. Experimental and computer simulated plant height and harvested boll number increased significantly with increased row spacing and, occasionally, in-row plant spacing. Modeled lint yield for 0.38 m rows decreased by approximately 50% compared with the 582 kg·ha-1 yield for conventional row spacing, which was practically duplicated by field observations in 2001 and 2004. Measured fiber quality occasionally improved with conventional row spacing over ultra-narrow rows, but was unaffected by plant spacing. Because narrow rows and frequent plant spacing did not improve lint yield or fiber quality of dryland cotton, we do not recommend this strategy to overcome a thermally limited growing season.展开更多
Mechanical pot-seedling transplanting is an innovatively developed transplanting method that has the potential to replace mechanical carpet-seedling transplanting. However, the initial pot-seedling transplanting machi...Mechanical pot-seedling transplanting is an innovatively developed transplanting method that has the potential to replace mechanical carpet-seedling transplanting. However, the initial pot-seedling transplanting machine lacked optimized density spacing and limited yield potential for japonica rice. Therefore, ascertaining the optimized density by wide-narrow rows and the appropriate transplanting method for yield formation and grain quality of japonica rice is of great importance for high-quality rice production. Field experiments were conducted using two japonica rice cultivars Nanjing 9108 and Nanjing 5055 under three transplanting methods in 2016 and 2017: mechanical pot-seedling transplanting with wide-narrow row(K, average row spacing of 30 cm);equidistant row(D, 33 cm×12 cm);and mechanical carpet-seedling transplanting(T, 30 cm×12.4 cm). In addition, five different density treatments were set in K(K1–K5, from 18.62×10~4 to 28.49×10~4 hills ha^(–1)). The results showed that the highest yield was produced by a planting density of 26.88×104 hills ha^(–1) in mechanical pot-seedling transplanting with wide-narrow row with a greater number of total spikelets that resulted from significantly more panicles per area and slightly more grain number per panicle, as compared with equidistant row, and yield among density in wide-narrow row showed a parabolic trend. Compared with mechanical carpet-seedling transplanting, the treatment of the highest yield increased yield significantly, which was mainly attributed to the larger sink size with improved filled-grain percentage and grain weight, higher harvest index, and increased total dry matter accumulation, especially the larger amount accumulated from heading stage to maturity stage. With the density in wide-narrow row decreasing, processing quality, appearance quality, and nutrition quality were all improved, whereas amylose content and the taste value were decreased. Compared with mechanical carpet-seedling transplanting, mechanical pot-seedling transplanting improved processing quality and nutrition quality, but decreased amylose content and deteriorated appearance quality. These results suggested that mechanical pot-seedling transplanting with wide-narrow row coupling produced a suitable planting density of 26.88×10~4 hills ha^(–1) and may be an alternative approach to improving grain yield and quality for japonica rice.展开更多
One of the main reasons behind reduced cane yield is pathetic method of planting. Planting method and row spacing are the most important yield contributing factors in sugarcane. A field experiment was carried out in o...One of the main reasons behind reduced cane yield is pathetic method of planting. Planting method and row spacing are the most important yield contributing factors in sugarcane. A field experiment was carried out in order to determine quality and yield of sugarcane in various spatial arrangements. Treatments are 180 cm spaced trenches with triple row strips;180 cm spaced trenches with alternate row strips;120 cm spaced trenches with double row strips and 60 cm spaced furrow with single row. Perusal of data revealed that 3.6%, 13.4%, 15%, 15.3% more cane diameter (cm), cane length (cm), stripped cane yield (t·haˉ1</sup>), sugar yield (t·haˉ1</sup>) were obtained from 180 cm spaced trenches with triple row strips as compared to conventional planting method i.e. 60 cm spaced furrows. While the number of millable canes mˉ2</sup>, polarity %, cane juice purity %, cane juice %, commercial cane sugar % and cane sugar recovery % remained non-significant by different planting techniques.展开更多
Experiments were located at Lower Niger River Basin Development Authority, Ejiba and Horticultural Section College of Agriculture, Kabba in 2014 cropping season to investigate the effect of different spacing and urea ...Experiments were located at Lower Niger River Basin Development Authority, Ejiba and Horticultural Section College of Agriculture, Kabba in 2014 cropping season to investigate the effect of different spacing and urea application rates on fruit nutrient composition, growth and fruit yield of tomato in derived savanna vegetation of Nigeria. Field experiments were arranged in a randomized complete block design in factorial fashion with three replications. The row spacing were 75 × 40 cm (33,333 plant·ha-1, 75 × 50 cm (26,666 plant·ha-1) and 75 × 60 cm (22,222 plant·ha-1) while the urea rates comprised control (0 kg urea·ha-1), 54.3 and 108.6 kg urea·ha-1. Growth and yield parameters taken were as follows: average plant height, stem girth, leaf area (m2) and yield per land area. Data were collected from ten randomly selected plants in each plot. The data were statistically analyzed using GENSTAT. The analysis of variance (ANOVA) was performed to find out the significance of variation among the treatments while the significant difference between mean treatments was separated using least significance Difference at 5% level of probability. The result obtained from this study indicated that urea application and spacing affected significantly growth parameters of tomato and yield per land area. It could be concluded that there was a significant increase in plant height, number of leaves, number of fruits per plant and final fruit weight of tomato as a result of urea fertilizer application at the rate of 108.6 kg urea/ha. However, this was not significantly better than plots with urea application at 54.8 kg/ha in both Ejiba and Kabba. Row spacing of 75 × 50 cm showed better performance in number of fruit and fruit yield per plots. Farmers in Ejiba and Kabba should apply urea at the rate of 54.8 kg per hectare and plant the crop at a row spacing of 75 × 50 cm for optimum yield and for a more profitable production of tomato.展开更多
Emergence of grasses late in the season has become a problem in glyphosate-resistant (GR) soybean production in the southern US. A 3-yr field study was conducted from 2011 to 2013 at Stoneville, MS to determine effica...Emergence of grasses late in the season has become a problem in glyphosate-resistant (GR) soybean production in the southern US. A 3-yr field study was conducted from 2011 to 2013 at Stoneville, MS to determine efficacy of post-harvest and pyroxasulfone-based in-crop herbicides on late-season grasses and yield in twin-row glyphosate-resistant soybean. Experiments were conducted in a split-plot arrangement of treatments in a randomized complete block design with fall herbicides (with and without pendimethalin at 1.12 kg ai ha-1 and paraquatat 0.84 kg ai ha-1) as main plots and in-crop herbicides as subplots with four replications. The six in-crop herbicide programs were: glyphosate applied early postemergence (EPOST) at 0.84 kg·aeha-1 followed by (fb) glyphosate late postemergence (LPOST) at 0.84 kg·ha-1 with and without pyroxasulfone preemergence (PRE) applied at 0.18 kg ai ha-1, pyroxasulfone PRE fb glyphosate at 0.84 kg·ha-1 LPOST or glyphosate at 0.84 kg·ha-1 + S-metolachlor at 1.68 kg ai ha-1 EPOST, pyroxasulfone PRE fb S-meto- lachlor at 1.12 kg·ha-1 + fomesafen at 0.27 kg ai ha-1 EPOST fb clethodim at 0.14 kg ai ha-1, and a no-herbicide control. Browntop millet, Digitaria spp., and junglerice densities at 2 weeks after LPOST, grass weed dry biomass at harvest, and soybean yield were similar regardless of post- harvest herbicides in all three years. At 2 weeks after LPOST, browntop millet, Digitaria spp. and junglerice densities were greatly reduced in all five in-crop herbicide treatments compared with no herbicide plot in all three years. Grass weed dry biomass in no-herbicide plots was 3346, 6136, and 6916 kg·ha-1 in 2011, 2012, and 2013, respectively and the five herbicide treatments reduced grass weed dry biomass by at least 87%, 84%, and 99% in 2011, 2012, and 2013, respectively. Soybean yield was higher with all five in-crop herbicide treatments compared to no herbicide control in all three years. These results indicate that browntop millet, Digitaria spp., and junglerice infestations can be reduced with pyroxasulfone-based in-crop herbicide programs in twin-row GR soybean.展开更多
A field experiment was conducted to study the growth and productivity of wheat as affected by row spacing and direction of sowing at Rampur, Chitwan, Nepal during the 2007-2008 wheat growing season. The experiment was...A field experiment was conducted to study the growth and productivity of wheat as affected by row spacing and direction of sowing at Rampur, Chitwan, Nepal during the 2007-2008 wheat growing season. The experiment was carried out in 3-factors factorial randomized complete block design comprising two varieties (Gautam and BL-2800), three row spacings (15, 20 and25 cm) and two row directions of sowing (east-west and north-south). The effects of variety and row direction of sowing on grain yield were significant (p < 0.05), but the grain yield was not affected by the row spacing treatment. BL-2800 variety produced higher grain yield (3.53 t·ha-1) as compared to Gautam (3.11 t·ha-1). Both wheat varieties yielded about 11% higher (p < 0.05) grain in the north-south sowing as compared to the eastwest sowing.展开更多
Despite the continuous advancements of engineering construction in high-intensity areas,many engineering landslides are still manufactured with huge thrust force,and double-row piles are effective to control such larg...Despite the continuous advancements of engineering construction in high-intensity areas,many engineering landslides are still manufactured with huge thrust force,and double-row piles are effective to control such large landslides.In this study,large shaking table test were performed to test and obtain multi-attribute seismic data such as feature image,acceleration,and dynamic soil pressure.Through the feature image processing analysis,the deformation characteristics for the slope reinforced by double-row piles were revealed.By analyzing the acceleration and the dynamic soil pressure time domain,the spatial dynamic response characteristics were revealed.Using Fast Fourier Transform and half-power bandwidth,the damping ratio of acceleration and dynamic soil pressure was obtained.Following that,the Seism Signal was used to calculate the spectral displacement of the accelerations to obtain the regional differences of spectral displacement.The results showed that the overall deformation mechanism of the slope originates from tension failure in the soil mass.The platform at the back of the slope was caused by seismic subsidence,and the peak acceleration ratio was positively correlated with the relative pile heights.The dynamic soil pressure of the front row piles showed an inverted"K"-shaped distribution,but that of the back row piles showed an"S"-shaped distribution.The predominant frequency of acceleration was 2.16 Hz,and the main frequency band was 0.7-6.87 Hz;for dynamic soil pressure,the two parameters became 1.15 Hz and 0.5-6.59 Hz,respectively.In conclusion,dynamic soil pressure was more sensitive to dampening effects than acceleration.Besides,compared to acceleration,dynamic soil pressure exhibited larger loss factors and lower resonance peaks.Finally,back row pile heads were highly sensitive to spectral displacement compared to front row pile heads.These findings may be of reference value for future seismic designs of double-row piles.展开更多
Biological yield indicates the potential for increasing yield.Leaf carbon metabolism plays an important role in the biomass accumulation of rapeseed(Brassica napus L.).Field experiments with the hybrid HZ62(with a con...Biological yield indicates the potential for increasing yield.Leaf carbon metabolism plays an important role in the biomass accumulation of rapeseed(Brassica napus L.).Field experiments with the hybrid HZ62(with a conventional plant architecture)grown in 2016–2017,and HZ62 and accession 1301(with a compact plant architecture)grown in 2017–2018 were conducted to characterize the physiological and proteomic responses of leaf photosynthetic carbon metabolism to density and row spacing configurations.The densities were set at 15×10;ha^(-1)(D1),30×10^(4)ha^(-1)(D2),and 45×10^(4)ha^(-1)(D3)(main plot),with row spacings of 15 cm(R15),25 cm(R25),and 35 cm(R35)(subplot).Individual and plant population biomass accumulation was greatest at R25,R15,and R15 for D1,D2,and D3,respectively,for both genotypes.In comparison with D1 R25,the individual aboveground biomass of HZ62 decreased by60.2%,whereas the population biomass increased by 31.9%,and the individual biomass of genotype1301 decreased by 54.0%and the population biomass increased by 53.9%at D3 R15.Leaf carbon metabolic enzymes varied between genotypes at flowering stage.In contrast to D1 R25,at D3 R15 the activities of ribulose-1,5-bisphosphate carboxylase/oxygenase(Rubisco)and sucrose phosphate synthase(SPS)and the contents of starch,sucrose and soluble sugars in leaves were significantly decreased in HZ62 and increased in genotype 1301.The activities of fructose-1,6-bisphosphatase(FBPase)decreased,in consistency with the abundance of fructose-bisphosphate aldolase in HZ62.In contrast,sucrose synthase(Su Sy)activity appeared to decrease in both genotypes,but a significant increase in abundance of a protein with sucrose synthase was found in the 1301 genotype by proteomic analysis.With increased density and reduced row spacing,the expression of most key proteins involved in carbon metabolism was elevated,and enzyme activity and carbon assimilate content were increased in 1301,whereas HZ62 showed the opposite trend,indicating that the compact plant type can accumulate more population biomass with denser planting.展开更多
AIM:To distinguish acinar cell carcinoma(ACC)from pancreatic adenocarcinoma(AC)by comparing their computed tomography findings.METHODS:Patients with ACC and AC were identified on the basis of results obtained using su...AIM:To distinguish acinar cell carcinoma(ACC)from pancreatic adenocarcinoma(AC)by comparing their computed tomography findings.METHODS:Patients with ACC and AC were identified on the basis of results obtained using surgically resected pancreatectomy specimens.The preoperative computer tomographic images of 6 acinar cell carcinoma patients and 67 pancreatic adenocarcinoma patients in 4 phases(non-contrast,arterial,portal venous,and delayed phase)were compared.The scan delay times were 40,70,and 120 s for each contrast-enhanced phase.The visual pattern,tomographic attenuation value,and time attenuation curve were assessed and compared between AC and ACC cases using the 2test,Wilcoxon signed-rank test,and Mann Whitney U test.RESULTS:The adenocarcinomas tended to be hypodense in all 4 phases.The acinar cell carcinomas also tended to be hypodense in the 3 contrast-enhancedphases,although their computed tomographic attenuation values were higher.Further,5 of the 6 acinar cell carcinomas(83%)were isodense in the non-contrast phase.The time attenuation curve of the adenocarcinomas showed a gradual increase through the 4 phases,and all adenocarcinomas showed peak enhancement during the delayed phase.The time attenuation curve of the acinar cell carcinomas showed peak enhancement during the portal venous phase in 4 cases and during the arterial phase in 2 cases.None of the 6 acinar cell carcinomas showed peak enhancement during the delayed phase.CONCLUSION:The tumor density in the non-contrast phase and time attenuation curve pattern clearly differ between acinar cell carcinomas and adenocarcinomas,and multidetector-row computed tomography can thus distinguish these tumors.展开更多
BACKGROUND In rotator cuff repair surgery,the double-row technique is widely performed.Studies have shown that with increased contact area and pressure between tendon and bone interface,better healing is promoted.AIM ...BACKGROUND In rotator cuff repair surgery,the double-row technique is widely performed.Studies have shown that with increased contact area and pressure between tendon and bone interface,better healing is promoted.AIM To assess the different suture configurations with the double-row technique and how this influences the contact area of the rotator cuff tendon to bone.METHODS This was a controlled laboratory study where identical tears were created in 24 fresh porcine shoulders over a 1.5 cm×2.5 cm infraspinatus insertion footprint.Double-row repair techniques,with 3 to 4-suture anchors in different configurations(2 medial,2 lateral vs 2 medial,1 lateral vs 1 medial,2 lateral),were employed for three control groups.Each group consisted of eight shoulders with identical repair configurations.Footprint contact areas of the repaired tendon against the tuberosity were determined using pressure sensitive Fujifilm placed between the tendon and tuberosity.RESULTS The mean contact area between tendon and insertion footprint from the imprinted Fujifilm was obtained using computer software.The contact area measured from a standard 4-suture anchor double row repair was 75.1±9.3 mm2,whereas areas obtained for the 2 lateral-1 medial and 2 medial-1 lateral anchor configurations were 72.9±5.2 mm2 and 75.0±4.9 mm2 respectively.No statistical significance was noted between the three groups.CONCLUSION In the technique of double-row repair,using a 3-suture anchor configuration may offer a non-inferior alternative to the standard 4-anchor construct in terms of efficacy.This may also result in overall cost reduction and shorter surgical time.展开更多
In order to screen suitable high hybrid wheat seed production technology,the split-plot experiment design was adopted and study was carried out about the effects of the different row ratios of male and female parents ...In order to screen suitable high hybrid wheat seed production technology,the split-plot experiment design was adopted and study was carried out about the effects of the different row ratios of male and female parents and application amount of nitrogen fertilizer on hybrid wheat seed production and its component factors. The results showed that the seed production increased with the increase in the number of female parent row. When the row ratio of male and female parents was 2 ∶ 6,the seed production was 3 683. 8 kg/ha; when the application amount of nitrogen fertilization was 50 kg/ha,the seed production was 3 649. 4 kg/ha; the interaction between the row ratio of male and female parents and the application amount of nitrogen fertilizer indicated that when the row ratio of male and female parents was 2∶ 6 and the application amount of nitrogen fertilizer was 300 kg/ha,the seed production reached the highest( 4160. 6 kg/ha). The row ratio of male and female parents and application amount of nitrogen fertilizer had significant effect on the component factors of seed production,including the number of grains per spike,spike weight and setting percentage. When the row ratio of male and female parents was 2∶ 5,the number of grains per spike,spike weight and setting percentage were the highest at 26. 7 grains,1. 12 g,and 62. 6% respectively; when application amount of nitrogen fertilizer was 450 kg/ha,the number of grains per spike,spike weight and setting percentage were the highest at 26. 0 grains,1. 08 g,and59. 2% respectively; the interaction of row ratio of male and female parents and application amount of nitrogen fertilizer had significant effect on the number of grains per spike,spike weight and setting percentage; when the row ratio of male and female parents was 2∶ 5 and the application amount of nitrogen fertilizer was 300 kg/ha,the number of grains per spike,spike weight and setting percentage were the highest at 29. 6grains,1. 24 g,and 71. 6% respectively. The number of grains per spike is the largest component factor for seed production. Increasing the number of grains per spike can increase the seed production. According to the effects of row ratio of male and female parents and application amount of nitrogen fertilizer on the component factors of seed production,the optimal condition was 2∶ 5-2∶ 6 for row ratio of male and female parents and 300-450 kg/ha for application amount of nitrogen fertilizer.展开更多
Based on the study on cultivation models of soybean narrow-row-flat-dense planting under the conditions of different between-row spacing and inter-plant spacing by using the comparison field experiment,and technical s...Based on the study on cultivation models of soybean narrow-row-flat-dense planting under the conditions of different between-row spacing and inter-plant spacing by using the comparison field experiment,and technical studies of the contour following the seeder unit,the anti-block,the lateral and stratified the deep fertilizing,according to the design ideas of planting units integration and variable between-row spacing from 30 to 45 cm,the 2BZJ-3/4 precision planter matched with 18-32 hp tractors has been developed for the popularization of the narrow-row-flat-dense planting soybean technique by means of Virtual Prototyping(VP) technology.展开更多
文摘When designing a solar power plant, it is much more important to avoid the shadow on the PV Panels. As the shadow falls on the PV Panels;it significantly reduces the generation of required power as planned and designed. This research paper and case study will help a lot to avoid shadow, especially when selecting inter-row spacing between the strings of solar power plants.
文摘In monoculture, crop failure due to biotic or abiotic causes can result in partial or total output failure. The yield, socio-economic, and environmental effects of intercropping on the farmer and the environment as a whole have not received much attention. There is a dearth of knowledge on the productivity of maize-groundnut intercrops in Ghana regarding the relative timing of planting and spatial arrangement of component crops. Therefore, the objective of the study was to determine the effects of spatial row arrangement and the time of planting intercrops on the productivity of groundnut under maize-groundnut intercropping. The 5 × 3 factorial field experiment was undertaken at the Miminaso community in the Ejura-Sekyedumase municipality of the Ashanti Region of Ghana during the 2020 cropping seasons. Treatments were evaluated in a Randomized Complete Block Design (RCBD) with three replicates. The levels of row arrangement of intercrops were: one row of maize and one row of groundnut (1M1G), one row of maize and two rows of groundnut (1M2G), two rows of maize and one row of groundnut (2M1G), two rows of maize and two rows of groundnut (2M2G), sole maize and sole groundnut (M/G). The levels of time of introducing groundnut included simultaneous planting of intercrops (0 WAP), planting groundnut one week after planting maize (1 WAP) and planting groundnut two weeks after planting maize (2 WAP). There were significant (P 0.05) treatment interactions for pod and seed yields of groundnut throughout the study. The highest groundnut pod yields of 1815.00 kg/ha and 2359.00 kg/ha were recorded by the 0WAP × 1M2G treatment in the major and minor seasons of 2020, respectively, while the highest groundnut seed yields of 741.00 kg/ha and 726.00 kg/ha were recorded in the major and minor rainy seasons of 2020 by 1WAP × G and 0WAP × G treatments, respectively. The highest seed yields of groundnut (404 kg/ha and 637 kg/ha for major and minor rainy seasons, respectively) were produced by 1WAP × 2M2G.
文摘The ligand o-phenylenediamine (opda) and its oxidized form, o-benzoquinonediimine (bqdi), act as a fascinating candidate coordinating toward transition metal ions leading to the photochemical hydrogen production in absence of photosensitizers. Herein, we report the systematic study of the interaction between the oxidized form bqdi ligand, tris-(o-benzoquinonediimine) with divalent first-row transition metal series using DFT calculations. The lowest energy structures, bond length, binding energies, frontier molecular orbital analysis, natural bond orbitals, and global reactivity descriptor were calculated using B3LYP/6-311G(d,P) level of theory. The time dependent-DFT at the CAM-B3LYP/6-311+G(d,p) level of theory was applied to determine the electronic structures and the optical spectra. The theoretical binding trend of the divalent first-row transition metal series is decreasing as follows: Cu >Ti > V > Co > Ni > Fe > Cr > Zn >Mn. Among them, the binding potency of iron (II) by the bqdi ligand was not predominantly sturdy as compared to other first-row divalent transition metal ions. The origin of strong coordination with Fe(II) is attributed to its extra capability to induce covalent coordination of bqdi ligands. The complex exhibited two strong peaks at 370 nm and 452 nm, due to the HOMO-3 to LUMO+1 and HOMO-1 to LUMO transitions, respectively. Natural bond orbital analysis showed that the major interaction happens between the N lone pair electrons of the ligand with an anti-bonding orbital of metal ions, in which Ti showed the highest interaction energy than other metal ions. The present systemic DFT study of bqdi ligands with the first-row transition metals strongly encourages the future establishment of photochemical hydrogen production in absence of photosensitizers.
文摘The declining Ogallala Aquifer beneath the Southern High Plains may necessitate dryland crop production and cotton (Gossypium hirsutum L.) is a well-adapted and potentially profitable alternative crop. The limited growing season duration of the Texas Panhandle and southwestern Kansas, however, imposes significant production risk due to incomplete boll maturation. Emphasizing earlier boll production that is usually confined to sites on lower fruiting branches may reduce risk, but offsetting high planting densities are needed to maintain desirable lint yield. Our objectives were to quantify planting: 1) row width and 2) in-row spacing effects on growth, yield, and fiber quality of dryland cotton. Field tests of row widths from 0.25 to 0.76 m and plant densities with in-row spacing ranging from 0.075 to 0.15 m were conducted from 1999 to 2005 on a nearly level Pullman clay loam (fine, mixed, superactive, thermic Torrertic Paleustoll) managed in a wheat (Triticum aestivum L.), cotton, fallow (W-Ctn-F) rotation. To expand the basis of comparison, cotton growth and yields were simulated using GOSSYM and long-term (1958-2000) weather records from Bushland, TX, as input for all combinations of 0.38 or 0.76 m row widths and plant spacing of 0.075, 0.10 and 0.15 m. Experimental and computer simulated plant height and harvested boll number increased significantly with increased row spacing and, occasionally, in-row plant spacing. Modeled lint yield for 0.38 m rows decreased by approximately 50% compared with the 582 kg·ha-1 yield for conventional row spacing, which was practically duplicated by field observations in 2001 and 2004. Measured fiber quality occasionally improved with conventional row spacing over ultra-narrow rows, but was unaffected by plant spacing. Because narrow rows and frequent plant spacing did not improve lint yield or fiber quality of dryland cotton, we do not recommend this strategy to overcome a thermally limited growing season.
基金funded by the National Key Research Program of China(2016YFD0300503)the Key Research Program of Jiangsu Province,China(BE2016344 and BE2018355)the Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions,China。
文摘Mechanical pot-seedling transplanting is an innovatively developed transplanting method that has the potential to replace mechanical carpet-seedling transplanting. However, the initial pot-seedling transplanting machine lacked optimized density spacing and limited yield potential for japonica rice. Therefore, ascertaining the optimized density by wide-narrow rows and the appropriate transplanting method for yield formation and grain quality of japonica rice is of great importance for high-quality rice production. Field experiments were conducted using two japonica rice cultivars Nanjing 9108 and Nanjing 5055 under three transplanting methods in 2016 and 2017: mechanical pot-seedling transplanting with wide-narrow row(K, average row spacing of 30 cm);equidistant row(D, 33 cm×12 cm);and mechanical carpet-seedling transplanting(T, 30 cm×12.4 cm). In addition, five different density treatments were set in K(K1–K5, from 18.62×10~4 to 28.49×10~4 hills ha^(–1)). The results showed that the highest yield was produced by a planting density of 26.88×104 hills ha^(–1) in mechanical pot-seedling transplanting with wide-narrow row with a greater number of total spikelets that resulted from significantly more panicles per area and slightly more grain number per panicle, as compared with equidistant row, and yield among density in wide-narrow row showed a parabolic trend. Compared with mechanical carpet-seedling transplanting, the treatment of the highest yield increased yield significantly, which was mainly attributed to the larger sink size with improved filled-grain percentage and grain weight, higher harvest index, and increased total dry matter accumulation, especially the larger amount accumulated from heading stage to maturity stage. With the density in wide-narrow row decreasing, processing quality, appearance quality, and nutrition quality were all improved, whereas amylose content and the taste value were decreased. Compared with mechanical carpet-seedling transplanting, mechanical pot-seedling transplanting improved processing quality and nutrition quality, but decreased amylose content and deteriorated appearance quality. These results suggested that mechanical pot-seedling transplanting with wide-narrow row coupling produced a suitable planting density of 26.88×10~4 hills ha^(–1) and may be an alternative approach to improving grain yield and quality for japonica rice.
文摘One of the main reasons behind reduced cane yield is pathetic method of planting. Planting method and row spacing are the most important yield contributing factors in sugarcane. A field experiment was carried out in order to determine quality and yield of sugarcane in various spatial arrangements. Treatments are 180 cm spaced trenches with triple row strips;180 cm spaced trenches with alternate row strips;120 cm spaced trenches with double row strips and 60 cm spaced furrow with single row. Perusal of data revealed that 3.6%, 13.4%, 15%, 15.3% more cane diameter (cm), cane length (cm), stripped cane yield (t·haˉ1</sup>), sugar yield (t·haˉ1</sup>) were obtained from 180 cm spaced trenches with triple row strips as compared to conventional planting method i.e. 60 cm spaced furrows. While the number of millable canes mˉ2</sup>, polarity %, cane juice purity %, cane juice %, commercial cane sugar % and cane sugar recovery % remained non-significant by different planting techniques.
文摘Experiments were located at Lower Niger River Basin Development Authority, Ejiba and Horticultural Section College of Agriculture, Kabba in 2014 cropping season to investigate the effect of different spacing and urea application rates on fruit nutrient composition, growth and fruit yield of tomato in derived savanna vegetation of Nigeria. Field experiments were arranged in a randomized complete block design in factorial fashion with three replications. The row spacing were 75 × 40 cm (33,333 plant·ha-1, 75 × 50 cm (26,666 plant·ha-1) and 75 × 60 cm (22,222 plant·ha-1) while the urea rates comprised control (0 kg urea·ha-1), 54.3 and 108.6 kg urea·ha-1. Growth and yield parameters taken were as follows: average plant height, stem girth, leaf area (m2) and yield per land area. Data were collected from ten randomly selected plants in each plot. The data were statistically analyzed using GENSTAT. The analysis of variance (ANOVA) was performed to find out the significance of variation among the treatments while the significant difference between mean treatments was separated using least significance Difference at 5% level of probability. The result obtained from this study indicated that urea application and spacing affected significantly growth parameters of tomato and yield per land area. It could be concluded that there was a significant increase in plant height, number of leaves, number of fruits per plant and final fruit weight of tomato as a result of urea fertilizer application at the rate of 108.6 kg urea/ha. However, this was not significantly better than plots with urea application at 54.8 kg/ha in both Ejiba and Kabba. Row spacing of 75 × 50 cm showed better performance in number of fruit and fruit yield per plots. Farmers in Ejiba and Kabba should apply urea at the rate of 54.8 kg per hectare and plant the crop at a row spacing of 75 × 50 cm for optimum yield and for a more profitable production of tomato.
文摘Emergence of grasses late in the season has become a problem in glyphosate-resistant (GR) soybean production in the southern US. A 3-yr field study was conducted from 2011 to 2013 at Stoneville, MS to determine efficacy of post-harvest and pyroxasulfone-based in-crop herbicides on late-season grasses and yield in twin-row glyphosate-resistant soybean. Experiments were conducted in a split-plot arrangement of treatments in a randomized complete block design with fall herbicides (with and without pendimethalin at 1.12 kg ai ha-1 and paraquatat 0.84 kg ai ha-1) as main plots and in-crop herbicides as subplots with four replications. The six in-crop herbicide programs were: glyphosate applied early postemergence (EPOST) at 0.84 kg·aeha-1 followed by (fb) glyphosate late postemergence (LPOST) at 0.84 kg·ha-1 with and without pyroxasulfone preemergence (PRE) applied at 0.18 kg ai ha-1, pyroxasulfone PRE fb glyphosate at 0.84 kg·ha-1 LPOST or glyphosate at 0.84 kg·ha-1 + S-metolachlor at 1.68 kg ai ha-1 EPOST, pyroxasulfone PRE fb S-meto- lachlor at 1.12 kg·ha-1 + fomesafen at 0.27 kg ai ha-1 EPOST fb clethodim at 0.14 kg ai ha-1, and a no-herbicide control. Browntop millet, Digitaria spp., and junglerice densities at 2 weeks after LPOST, grass weed dry biomass at harvest, and soybean yield were similar regardless of post- harvest herbicides in all three years. At 2 weeks after LPOST, browntop millet, Digitaria spp. and junglerice densities were greatly reduced in all five in-crop herbicide treatments compared with no herbicide plot in all three years. Grass weed dry biomass in no-herbicide plots was 3346, 6136, and 6916 kg·ha-1 in 2011, 2012, and 2013, respectively and the five herbicide treatments reduced grass weed dry biomass by at least 87%, 84%, and 99% in 2011, 2012, and 2013, respectively. Soybean yield was higher with all five in-crop herbicide treatments compared to no herbicide control in all three years. These results indicate that browntop millet, Digitaria spp., and junglerice infestations can be reduced with pyroxasulfone-based in-crop herbicide programs in twin-row GR soybean.
文摘A field experiment was conducted to study the growth and productivity of wheat as affected by row spacing and direction of sowing at Rampur, Chitwan, Nepal during the 2007-2008 wheat growing season. The experiment was carried out in 3-factors factorial randomized complete block design comprising two varieties (Gautam and BL-2800), three row spacings (15, 20 and25 cm) and two row directions of sowing (east-west and north-south). The effects of variety and row direction of sowing on grain yield were significant (p < 0.05), but the grain yield was not affected by the row spacing treatment. BL-2800 variety produced higher grain yield (3.53 t·ha-1) as compared to Gautam (3.11 t·ha-1). Both wheat varieties yielded about 11% higher (p < 0.05) grain in the north-south sowing as compared to the eastwest sowing.
基金the financial support by the National Key R&D Program of China(No.2018YFC1504901)Gansu Province Youth Science and Technology Fund program,China(Grant No.21JR7RA739)+1 种基金Natural Science Foundation of Gansu Province,China(Grant No.21JR7RA738)Natural Science Foundation of Gansu Province,China(No.145RJZA068)。
文摘Despite the continuous advancements of engineering construction in high-intensity areas,many engineering landslides are still manufactured with huge thrust force,and double-row piles are effective to control such large landslides.In this study,large shaking table test were performed to test and obtain multi-attribute seismic data such as feature image,acceleration,and dynamic soil pressure.Through the feature image processing analysis,the deformation characteristics for the slope reinforced by double-row piles were revealed.By analyzing the acceleration and the dynamic soil pressure time domain,the spatial dynamic response characteristics were revealed.Using Fast Fourier Transform and half-power bandwidth,the damping ratio of acceleration and dynamic soil pressure was obtained.Following that,the Seism Signal was used to calculate the spectral displacement of the accelerations to obtain the regional differences of spectral displacement.The results showed that the overall deformation mechanism of the slope originates from tension failure in the soil mass.The platform at the back of the slope was caused by seismic subsidence,and the peak acceleration ratio was positively correlated with the relative pile heights.The dynamic soil pressure of the front row piles showed an inverted"K"-shaped distribution,but that of the back row piles showed an"S"-shaped distribution.The predominant frequency of acceleration was 2.16 Hz,and the main frequency band was 0.7-6.87 Hz;for dynamic soil pressure,the two parameters became 1.15 Hz and 0.5-6.59 Hz,respectively.In conclusion,dynamic soil pressure was more sensitive to dampening effects than acceleration.Besides,compared to acceleration,dynamic soil pressure exhibited larger loss factors and lower resonance peaks.Finally,back row pile heads were highly sensitive to spectral displacement compared to front row pile heads.These findings may be of reference value for future seismic designs of double-row piles.
基金the National Natural Science Foundation of China(31671616)the China Agriculture Research System(CARS-12)the Fundamental Research Funds for the Central Universities(2662019PY076)。
文摘Biological yield indicates the potential for increasing yield.Leaf carbon metabolism plays an important role in the biomass accumulation of rapeseed(Brassica napus L.).Field experiments with the hybrid HZ62(with a conventional plant architecture)grown in 2016–2017,and HZ62 and accession 1301(with a compact plant architecture)grown in 2017–2018 were conducted to characterize the physiological and proteomic responses of leaf photosynthetic carbon metabolism to density and row spacing configurations.The densities were set at 15×10;ha^(-1)(D1),30×10^(4)ha^(-1)(D2),and 45×10^(4)ha^(-1)(D3)(main plot),with row spacings of 15 cm(R15),25 cm(R25),and 35 cm(R35)(subplot).Individual and plant population biomass accumulation was greatest at R25,R15,and R15 for D1,D2,and D3,respectively,for both genotypes.In comparison with D1 R25,the individual aboveground biomass of HZ62 decreased by60.2%,whereas the population biomass increased by 31.9%,and the individual biomass of genotype1301 decreased by 54.0%and the population biomass increased by 53.9%at D3 R15.Leaf carbon metabolic enzymes varied between genotypes at flowering stage.In contrast to D1 R25,at D3 R15 the activities of ribulose-1,5-bisphosphate carboxylase/oxygenase(Rubisco)and sucrose phosphate synthase(SPS)and the contents of starch,sucrose and soluble sugars in leaves were significantly decreased in HZ62 and increased in genotype 1301.The activities of fructose-1,6-bisphosphatase(FBPase)decreased,in consistency with the abundance of fructose-bisphosphate aldolase in HZ62.In contrast,sucrose synthase(Su Sy)activity appeared to decrease in both genotypes,but a significant increase in abundance of a protein with sucrose synthase was found in the 1301 genotype by proteomic analysis.With increased density and reduced row spacing,the expression of most key proteins involved in carbon metabolism was elevated,and enzyme activity and carbon assimilate content were increased in 1301,whereas HZ62 showed the opposite trend,indicating that the compact plant type can accumulate more population biomass with denser planting.
文摘AIM:To distinguish acinar cell carcinoma(ACC)from pancreatic adenocarcinoma(AC)by comparing their computed tomography findings.METHODS:Patients with ACC and AC were identified on the basis of results obtained using surgically resected pancreatectomy specimens.The preoperative computer tomographic images of 6 acinar cell carcinoma patients and 67 pancreatic adenocarcinoma patients in 4 phases(non-contrast,arterial,portal venous,and delayed phase)were compared.The scan delay times were 40,70,and 120 s for each contrast-enhanced phase.The visual pattern,tomographic attenuation value,and time attenuation curve were assessed and compared between AC and ACC cases using the 2test,Wilcoxon signed-rank test,and Mann Whitney U test.RESULTS:The adenocarcinomas tended to be hypodense in all 4 phases.The acinar cell carcinomas also tended to be hypodense in the 3 contrast-enhancedphases,although their computed tomographic attenuation values were higher.Further,5 of the 6 acinar cell carcinomas(83%)were isodense in the non-contrast phase.The time attenuation curve of the adenocarcinomas showed a gradual increase through the 4 phases,and all adenocarcinomas showed peak enhancement during the delayed phase.The time attenuation curve of the acinar cell carcinomas showed peak enhancement during the portal venous phase in 4 cases and during the arterial phase in 2 cases.None of the 6 acinar cell carcinomas showed peak enhancement during the delayed phase.CONCLUSION:The tumor density in the non-contrast phase and time attenuation curve pattern clearly differ between acinar cell carcinomas and adenocarcinomas,and multidetector-row computed tomography can thus distinguish these tumors.
文摘BACKGROUND In rotator cuff repair surgery,the double-row technique is widely performed.Studies have shown that with increased contact area and pressure between tendon and bone interface,better healing is promoted.AIM To assess the different suture configurations with the double-row technique and how this influences the contact area of the rotator cuff tendon to bone.METHODS This was a controlled laboratory study where identical tears were created in 24 fresh porcine shoulders over a 1.5 cm×2.5 cm infraspinatus insertion footprint.Double-row repair techniques,with 3 to 4-suture anchors in different configurations(2 medial,2 lateral vs 2 medial,1 lateral vs 1 medial,2 lateral),were employed for three control groups.Each group consisted of eight shoulders with identical repair configurations.Footprint contact areas of the repaired tendon against the tuberosity were determined using pressure sensitive Fujifilm placed between the tendon and tuberosity.RESULTS The mean contact area between tendon and insertion footprint from the imprinted Fujifilm was obtained using computer software.The contact area measured from a standard 4-suture anchor double row repair was 75.1±9.3 mm2,whereas areas obtained for the 2 lateral-1 medial and 2 medial-1 lateral anchor configurations were 72.9±5.2 mm2 and 75.0±4.9 mm2 respectively.No statistical significance was noted between the three groups.CONCLUSION In the technique of double-row repair,using a 3-suture anchor configuration may offer a non-inferior alternative to the standard 4-anchor construct in terms of efficacy.This may also result in overall cost reduction and shorter surgical time.
基金Supported by State Key Research and Development Program of Ministry of Science and Technology(2016YFD0101603)Fundamental Research Funds for the Central Universities in 2016(XDJK2016A020)
文摘In order to screen suitable high hybrid wheat seed production technology,the split-plot experiment design was adopted and study was carried out about the effects of the different row ratios of male and female parents and application amount of nitrogen fertilizer on hybrid wheat seed production and its component factors. The results showed that the seed production increased with the increase in the number of female parent row. When the row ratio of male and female parents was 2 ∶ 6,the seed production was 3 683. 8 kg/ha; when the application amount of nitrogen fertilization was 50 kg/ha,the seed production was 3 649. 4 kg/ha; the interaction between the row ratio of male and female parents and the application amount of nitrogen fertilizer indicated that when the row ratio of male and female parents was 2∶ 6 and the application amount of nitrogen fertilizer was 300 kg/ha,the seed production reached the highest( 4160. 6 kg/ha). The row ratio of male and female parents and application amount of nitrogen fertilizer had significant effect on the component factors of seed production,including the number of grains per spike,spike weight and setting percentage. When the row ratio of male and female parents was 2∶ 5,the number of grains per spike,spike weight and setting percentage were the highest at 26. 7 grains,1. 12 g,and 62. 6% respectively; when application amount of nitrogen fertilizer was 450 kg/ha,the number of grains per spike,spike weight and setting percentage were the highest at 26. 0 grains,1. 08 g,and59. 2% respectively; the interaction of row ratio of male and female parents and application amount of nitrogen fertilizer had significant effect on the number of grains per spike,spike weight and setting percentage; when the row ratio of male and female parents was 2∶ 5 and the application amount of nitrogen fertilizer was 300 kg/ha,the number of grains per spike,spike weight and setting percentage were the highest at 29. 6grains,1. 24 g,and 71. 6% respectively. The number of grains per spike is the largest component factor for seed production. Increasing the number of grains per spike can increase the seed production. According to the effects of row ratio of male and female parents and application amount of nitrogen fertilizer on the component factors of seed production,the optimal condition was 2∶ 5-2∶ 6 for row ratio of male and female parents and 300-450 kg/ha for application amount of nitrogen fertilizer.
基金Supported by National Key Technology R&D Program(2006BAD11A05)National Soybean Industry Technology System
文摘Based on the study on cultivation models of soybean narrow-row-flat-dense planting under the conditions of different between-row spacing and inter-plant spacing by using the comparison field experiment,and technical studies of the contour following the seeder unit,the anti-block,the lateral and stratified the deep fertilizing,according to the design ideas of planting units integration and variable between-row spacing from 30 to 45 cm,the 2BZJ-3/4 precision planter matched with 18-32 hp tractors has been developed for the popularization of the narrow-row-flat-dense planting soybean technique by means of Virtual Prototyping(VP) technology.
