Based on the effective structure of the self-mixing interference effects,a general model for the self-mixing interference effects in the LD pumped solid-state laser has been established for the first time.The numerica...Based on the effective structure of the self-mixing interference effects,a general model for the self-mixing interference effects in the LD pumped solid-state laser has been established for the first time.The numerical simulation of the self-mixing interference signal has been done,the results show that when the external cavity length is integral times of 1/2,1/3,2/3,1/4,3/4 of the effective cavity length,the intensity of the self-mixing interference signals reach maximum in value.While that of single mode laser is integral times of half of the effective cavity length,the measuring precision of displacement of single mode laser is λ/2.A conclusion can be drawn from the above results that the measuring precision of displacement of multi-mode laser is higher than that of single mode laser.展开更多
ASeblsf-tmraicxti：n gA innteewrf esreelnf-cme ioxcincgu rms iicnr oa -liansteerrf derioodmee t（eLrD b）a sbeyd r eofnl eecxtitnergn tahl ep lhiagshet fmroomdu ala tmioinrr oisr-plirkees etanrtgedet. in front of the ...ASeblsf-tmraicxti：n gA innteewrf esreelnf-cme ioxcincgu rms iicnr oa -liansteerrf derioodmee t（eLrD b）a sbeyd r eofnl eecxtitnergn tahl ep lhiagshet fmroomdu ala tmioinrr oisr-plirkees etanrtgedet. in front of the laser. Sinusoidal phase modulation of the beam is obtained by an electro-optic crystal （EOC） in the external cavity. The phase of the interference signal is demodulated by Fourier analysis method. The combination of the modulation and demodulation decreases the sensitivity of the instru-ment to fluctuations of the laser power and the noise induced by environment. Experimentally, the new micro-interferometer is applied to measure the micro-displacement of a high precision commer-cial PZT with an accuracy of 〈10 nm.展开更多
Laser self-mixing interference（SMI） wave plate measurement method is a burgeoning technique for its simplicity and efficiency. But for the non-coated sample, the reflected light from the surface can seriously affect...Laser self-mixing interference（SMI） wave plate measurement method is a burgeoning technique for its simplicity and efficiency. But for the non-coated sample, the reflected light from the surface can seriously affect the measurement results.To analyze the reason theoretically, a self-consistent model for laser operation with a sub-external and an external cavity is established, and the sub-external cavity formed by the sample and a cavity mirror is proved to be the main error source.A synchronous tuning method is proposed to eliminate the sub-external cavity effect. Experiments are carried out on the synchronously tuning double external cavities self-mixing interference system, and the error of the system is in the range of -0.435°~0.387° compared with the ellipsometer. The research plays an important role in improving the performance and enlarging the application range of the laser self-mixing interference system.展开更多
Fibre sensors exhibit a number of advantages over other sensors such as high sensitivity, electric insulation, corrosion resistance, interference rejection and so on. And laser self-mixing interference can accurately ...Fibre sensors exhibit a number of advantages over other sensors such as high sensitivity, electric insulation, corrosion resistance, interference rejection and so on. And laser self-mixing interference can accurately detect the phase difference of feedback light. In this paper, a novel laser self-mixing interference fibre sensor that combines the advantages of fibre sensors with those of laser self-mixing interference is presented. Experimental configurations are set up to study the relationship between laser power output and phase of laser feedback light when the fibre trembles or when the fibre is stretched or pressed. The theoretical analysis of pressure sensors based on laser self-mixing interference is indicated to accord with the experimental results.展开更多
Transparent liquid flattening or stretching realizes optical path length modulation. A flat thin seal transparent cavity, one flank is an electromagnetic driving membrane and is filled over with transparent liquid. Vi...Transparent liquid flattening or stretching realizes optical path length modulation. A flat thin seal transparent cavity, one flank is an electromagnetic driving membrane and is filled over with transparent liquid. Vibration of the membrane makes the liquid compressing or stretching, changes the liquid layer thickness, i.e. the optical path length of light through the liquid layer. The liquid layer compressed is equivalent to increase membrane tension. The membrane has higher resonant frequency. The cavity diameter 10 mm modulation frequency is about 18 kHz.展开更多
Recently, with the rapid development of precision machining, microvibration measurement is required for the manufacturing and installation of parts and components. In this paper, a self-mixing microvibration measureme...Recently, with the rapid development of precision machining, microvibration measurement is required for the manufacturing and installation of parts and components. In this paper, a self-mixing microvibration measurement system of a π-phase shifted Distributed feedback (DFB) fiber laser is introduced. An all-fiberized configuration Er<sup>3+</sup>-Yb<sup>3+</sup> co-doped DFB fiber laser was used as light source, in which an active π-phase shifted fiber Bragg grating (FBG) was wrote on Er<sup>3+</sup>-Yb<sup>3+</sup> co-doped fiber. Using this, it can easily get a single-mode lasing with narrow linewidth. Experimental results demonstrate that the amplitude of vibration can be achieved down to λ/5 without any modulation parts while utilizing the reflecting mirror. It is in good agreement with the theoretical analysis and very helpful in proving sensitivity and stability of the measurement system. In addition, remote vibration measurement with a distance of 20 km is also realized with this system.展开更多
In this paper, a simplified optical millimeter-wave generated by two optical sidebands beating together in a 60 GHz radio over fiber (RoF) system with 10 Gbit/s 4-pulse amplitude modulation (4 PAM) transmission signal...In this paper, a simplified optical millimeter-wave generated by two optical sidebands beating together in a 60 GHz radio over fiber (RoF) system with 10 Gbit/s 4-pulse amplitude modulation (4 PAM) transmission signal is proposed and simulated. 10 Gbit/s electrical 4 PAM signals modulated are conveyed over the length of 40 km standard single mode fiber (SMF) and recovered via the self-mixing technique after detecting directly at the receiver. Graphs of time-domain wave, frequency-domain and optical spectrum are measured out in different period, and the comparison of error vector magnitude curves of NRZ and 4 PAM signals under the different length of fiber is accomplished. The capacity of 4 PAM modulation is higher, though NRZ performs better than 4 PAM selected in RoF system within 80 km of fiber length as shown in the simulation results.展开更多
In this work,we propose a method using frequency-modulated continuous-wave(FMCW)self-mixing interferometry(SMI)and all-phase fast Fourier transform(APFFT)for simultaneous measurement of speed and distance.APFFT offers...In this work,we propose a method using frequency-modulated continuous-wave(FMCW)self-mixing interferometry(SMI)and all-phase fast Fourier transform(APFFT)for simultaneous measurement of speed and distance.APFFT offers superior accuracy in frequency determination by mitigating issues like the fence effect and spectrum leakage,contributing to the high-accuracy measurement for speed and distance.Both simulations and experiments have demonstrated relative errors at the levels of 10^(−4) and 10^(−3) for distance and speed measurements,respectively.Furthermore,factors impacting measurement performance have been discussed.The proposed method provides a high-performance and cost-effective solution for distance and speed measurements,applicable across scientific research and various industrial domains.展开更多
The self-mixing interferometry(SMI)technique is an emerging sensing technology in microscale particle classification.However,due to the nature of the SMI effect raised by a microscattering particle,the signal analysis...The self-mixing interferometry(SMI)technique is an emerging sensing technology in microscale particle classification.However,due to the nature of the SMI effect raised by a microscattering particle,the signal analysis suffers from many problems compared with a macro target,such as lower signal-to-noise ratio(SNR),short transit time,and time-varying modulation strength.Therefore,the particle sizing measurement resolution is much lower than the one in typical displacement measurements.To solve these problems,in this paper,first,a theoretical model of the phase variation of a singleparticle SMI signal burst is demonstrated in detail.The relationship between the phase variation and the particle size is investigated,which predicts that phase observation could be another alternative for particle detection.Second,combined with continuous wavelet transform and Hilbert transform,a novel phase-unwrapping algorithm is proposed.This algorithm can implement not only efficient individual burst extraction from the noisy raw signal,but also precise phase calculation for particle sizing.The measurement shows good accuracy over a range from 100 nm to 6μm with our algorithm,proving that our algorithm enables a simple and reliable quantitative particle characteristics retrieval and analysis methodology for microscale particle detection in biomedical or laser manufacturing fields.展开更多
In order to achieve the accurate measurement of displacement, this Letter presents a self-mixing interference displacement measurement method suitable for the speckle effect. Because of the speckle effect, the amplitu...In order to achieve the accurate measurement of displacement, this Letter presents a self-mixing interference displacement measurement method suitable for the speckle effect. Because of the speckle effect, the amplitude of the self-mixing interference signal fluctuates greatly, which will affect the measurement accuracy of displacement. The ensemble empirical mode decomposition is used to process the interference signal, which can filter out high-frequency noise and low-frequency noise at the same time. The envelope of the self-mixing interference signal is extracted by Hilbert transform, and it is used to realize the normalization of the signal. Through a series of signal processing, the influence of speckle can be effectively reduced, and the self-mixing interference signal can be transformed into standard form. The displacement can be reconstructed by fringe counting and the interpolation method. The experimental results show that the method is successfully applied to the displacement measurement in the presence of speckle, which verifies the effectiveness and feasibility of the method.展开更多
An improved self-mixing grating interferometer based on the Littrow structure has been proposed in this Letter to measure displacement.The grating is integrated inside the interferometer to reduce the impact on the vi...An improved self-mixing grating interferometer based on the Littrow structure has been proposed in this Letter to measure displacement.The grating is integrated inside the interferometer to reduce the impact on the vibration parameters of the object caused by the grating attached to the vibrating object.The+1 st diffracted light returns to the laser cavity after being reflected by the target object,and self-mixing interference occurs.The displacement can be reconstructed by processing the self-mixing signals.The feasibility of the proposed interferometer is demonstrated by experimental measurements,and results show that it can achieve micro displacement measurement with the maximum absolute errors of less than 50 nm.展开更多
Micro-displacement measurement based on self-mixing interference using a fiber laser system was demonstrated. The sinusoidal phase modulation technique was introduced into the fiber laser self-mixing interference meas...Micro-displacement measurement based on self-mixing interference using a fiber laser system was demonstrated. The sinusoidal phase modulation technique was introduced into the fiber laser self-mixing interference measurement system to improve the measurement resolution. The phase could be demodulated by the Fourier analysis method. Error sources were evaluated in detail, and the system was experimentally applied to reconstruct the motion of a high-precision commercial piezoelectric ceramic transducer （PZT）. The displacement measurement resolution was well beyond a half-wavelength. It provides a practical solution for displacement measurement based on all optical-fiber sensing applications with high precision.展开更多
A self-mixing interferometer(SMI)with resolution twenty times higher than that of a conventional interferometer is developed by multiple reflections.Only by employing a simple external reflecting mirror,the multiple-p...A self-mixing interferometer(SMI)with resolution twenty times higher than that of a conventional interferometer is developed by multiple reflections.Only by employing a simple external reflecting mirror,the multiple-pass optical configuration can be constructed.The advantage of the configuration is simple and easy to make the light re-injected back into the laser cavity.Theoretical analysis shows that the resolution of measurement is scalable by adjusting the number of reflections.The experiment shows that the proposed method has the optical resolution of approximateλ/40.The influence of displacement sensitivity gain(G)is further analyzed and discussed in practical experiments.展开更多
Self-mixing interferometry(SMI)is an attractive sensing scheme that typically relies on mono-modal operation of an employed laser diode.However,change in laser modality can occur due to change in operating conditions....Self-mixing interferometry(SMI)is an attractive sensing scheme that typically relies on mono-modal operation of an employed laser diode.However,change in laser modality can occur due to change in operating conditions.So,detection of occurrence of multi-modality in SMI signals is necessary to avoid erroneous metric measurements.Typically,processing of multi-modal SMI signals is a difficult task due to the diverse and complex nature of such signals.However,the proposed techniques can significantly ease this task by identifying the modal state of SMI signals with 100%success rate so that interferometric fringes can be correctly interpreted for metric sensing applications.展开更多
In this paper, we present a method based on self-mixing interferometry combing extreme learning machine for real-time human blood pressure measurement. A signal processing method based on wavelet transform is applied ...In this paper, we present a method based on self-mixing interferometry combing extreme learning machine for real-time human blood pressure measurement. A signal processing method based on wavelet transform is applied to extract reversion point in the self-mixing interference signal, thus the pulse wave profile is successfully reconstructed. Considering the blood pressure values are intrinsically related to characteristic parameters of the pulse wave, 80 samples from the MIMIC-II database are used to train the extreme learning machine blood pressure model. In the experiment, 15 measured samples of pulse wave signal are used as the prediction sets. The results show that the errors of systolic and diastolic blood pressure are both within 5 mm Hg compared with that by the Coriolis method.展开更多
Based on a single-channel laser self-mixing interferometcr, we present a new silnultaneous measurement of the vibration amplitude and tile rotation angle of objects that both affect the power spectrum containing two p...Based on a single-channel laser self-mixing interferometcr, we present a new silnultaneous measurement of the vibration amplitude and tile rotation angle of objects that both affect the power spectrum containing two peaks of the interferometer signals. The fitted results indicate that the curve of the peak frequency versus the vibration amplitude follows a linear distribution, and the curve of the difference of the two-peak power values versus the angle follows a Gaussian distribution. A vibration amplitude with an error less than 3.0% and a rotation angle with an error less than 11.7% are calculated from the fitted results.展开更多
At the mirrors of a laser diode self-mixing interferometer,the output beams carry anti-correlated(i.e.f in phase opposition)interferometric signals,whereas the superposed noise fluctuations are(partially)correlated.Th...At the mirrors of a laser diode self-mixing interferometer,the output beams carry anti-correlated(i.e.f in phase opposition)interferometric signals,whereas the superposed noise fluctuations are(partially)correlated.Therefore,by using an instrumental output of the interferometer as the difference of the two,we double the amplitude of the self-mixing useful signal,while the superposed noise is reduced.To validate the idea,we first calculate the noise reduction by means of a second-quantization model,finding that in a laser diode the signal-to-noise ratio(SNR)can be improved by 8.2 dB,typically.Then,we also carry out an experimental measurement of SNR and find very good agreement with the theoretical result.展开更多
Laser self-mixing interferometer has the advantages of simple architecture, compact size, naturally self-aligned optical characteristics, and low cost. It is promising to replace conventional interferometers for physi...Laser self-mixing interferometer has the advantages of simple architecture, compact size, naturally self-aligned optical characteristics, and low cost. It is promising to replace conventional interferometers for physical measurements, such as displacement, distance, velocity, vibration, and so on. In this paper, this interferometer was tried to be used for micro-electro- mechanical system （MEMS） dynamic measurement. Firstly, its measurement principle based on a three-mirror cavity model was presented, and then the laser self-mixing interferometer for MEMS dynamic measurement was designed, experiments were finally performed as target moves with different forms. Experimental results suggest that self-mixing interferometer is available for MEMS dynamic measurement, and may have wider applications in the future.展开更多
In this paper,we present a phase multiplication algorithm(PMA)to obtain scalable fringe precision in laser self-mixing interferometer under a weak feedback regime.Merely by applying the double angle formula on the sel...In this paper,we present a phase multiplication algorithm(PMA)to obtain scalable fringe precision in laser self-mixing interferometer under a weak feedback regime.Merely by applying the double angle formula on the self-mixing signal multiple times,the continuously improved fringe precision will be obtained.Theoretical analysis shows that the precision of the fringe could be improved toλ/2^(n+1).The validity of the proposed method is demonstrated by means of simulated SMI signals and confirmed by experiments under different amplitudes.A fringe precision ofλ/128 at a sampling rate of 500 k S/s has been achieved after doing 6 th the PMA.Finally,an amplitude of 50 nm has been proved to be measurable and the absolute error is 3.07 nm,which is within the theoretical error range.The proposed method for vibration measurement has the advantage of high accuracy and reliable without adding any additional optical elements in the optical path,thus it will play an important role in nanoscale measurement field.展开更多
We report the fabrication and characterization of a single-layer graphene field-effect terahertz detector, which is cou- pled with dipole-like antennas based on the self-mixing detector model. The graphene is grown by...We report the fabrication and characterization of a single-layer graphene field-effect terahertz detector, which is cou- pled with dipole-like antennas based on the self-mixing detector model. The graphene is grown by chemical vapor deposi- tion and then transferred onto an SiO2/Si substrate. We demonstrate room-temperature detection at 237 GHz. The detector could offer a voltage responsivity of 0.1 V/W and a noise equivalent power of 207 nW/Hz 1/2. Our modeling indicates that the observed photovoltage in the p-type gated channel can be well fit by the self-mixing theory. A different photoresponse other than self-mixing may apply for the n-type gated channel.展开更多
文摘Based on the effective structure of the self-mixing interference effects,a general model for the self-mixing interference effects in the LD pumped solid-state laser has been established for the first time.The numerical simulation of the self-mixing interference signal has been done,the results show that when the external cavity length is integral times of 1/2,1/3,2/3,1/4,3/4 of the effective cavity length,the intensity of the self-mixing interference signals reach maximum in value.While that of single mode laser is integral times of half of the effective cavity length,the measuring precision of displacement of single mode laser is λ/2.A conclusion can be drawn from the above results that the measuring precision of displacement of multi-mode laser is higher than that of single mode laser.
基金Selected from Proceedings of the 7th International Conference on Frontiers of Design and Manufacturing (ICFDM’2006)This project is supported by Na-tional Natural Science Foundation of China (No. 50375074)Specialized Research Fund for the Doctoral Program of Higher Education (No. 20050319007).
文摘ASeblsf-tmraicxti：n gA innteewrf esreelnf-cme ioxcincgu rms iicnr oa -liansteerrf derioodmee t（eLrD b）a sbeyd r eofnl eecxtitnergn tahl ep lhiagshet fmroomdu ala tmioinrr oisr-plirkees etanrtgedet. in front of the laser. Sinusoidal phase modulation of the beam is obtained by an electro-optic crystal （EOC） in the external cavity. The phase of the interference signal is demodulated by Fourier analysis method. The combination of the modulation and demodulation decreases the sensitivity of the instru-ment to fluctuations of the laser power and the noise induced by environment. Experimentally, the new micro-interferometer is applied to measure the micro-displacement of a high precision commer-cial PZT with an accuracy of 〈10 nm.
文摘Laser self-mixing interference（SMI） wave plate measurement method is a burgeoning technique for its simplicity and efficiency. But for the non-coated sample, the reflected light from the surface can seriously affect the measurement results.To analyze the reason theoretically, a self-consistent model for laser operation with a sub-external and an external cavity is established, and the sub-external cavity formed by the sample and a cavity mirror is proved to be the main error source.A synchronous tuning method is proposed to eliminate the sub-external cavity effect. Experiments are carried out on the synchronously tuning double external cavities self-mixing interference system, and the error of the system is in the range of -0.435°~0.387° compared with the ellipsometer. The research plays an important role in improving the performance and enlarging the application range of the laser self-mixing interference system.
基金Project supported by the foundations of State Key Lab of Precision Measurement Technology & Instruments, Tsinghua University,China
文摘Fibre sensors exhibit a number of advantages over other sensors such as high sensitivity, electric insulation, corrosion resistance, interference rejection and so on. And laser self-mixing interference can accurately detect the phase difference of feedback light. In this paper, a novel laser self-mixing interference fibre sensor that combines the advantages of fibre sensors with those of laser self-mixing interference is presented. Experimental configurations are set up to study the relationship between laser power output and phase of laser feedback light when the fibre trembles or when the fibre is stretched or pressed. The theoretical analysis of pressure sensors based on laser self-mixing interference is indicated to accord with the experimental results.
文摘Transparent liquid flattening or stretching realizes optical path length modulation. A flat thin seal transparent cavity, one flank is an electromagnetic driving membrane and is filled over with transparent liquid. Vibration of the membrane makes the liquid compressing or stretching, changes the liquid layer thickness, i.e. the optical path length of light through the liquid layer. The liquid layer compressed is equivalent to increase membrane tension. The membrane has higher resonant frequency. The cavity diameter 10 mm modulation frequency is about 18 kHz.
文摘Recently, with the rapid development of precision machining, microvibration measurement is required for the manufacturing and installation of parts and components. In this paper, a self-mixing microvibration measurement system of a π-phase shifted Distributed feedback (DFB) fiber laser is introduced. An all-fiberized configuration Er<sup>3+</sup>-Yb<sup>3+</sup> co-doped DFB fiber laser was used as light source, in which an active π-phase shifted fiber Bragg grating (FBG) was wrote on Er<sup>3+</sup>-Yb<sup>3+</sup> co-doped fiber. Using this, it can easily get a single-mode lasing with narrow linewidth. Experimental results demonstrate that the amplitude of vibration can be achieved down to λ/5 without any modulation parts while utilizing the reflecting mirror. It is in good agreement with the theoretical analysis and very helpful in proving sensitivity and stability of the measurement system. In addition, remote vibration measurement with a distance of 20 km is also realized with this system.
文摘In this paper, a simplified optical millimeter-wave generated by two optical sidebands beating together in a 60 GHz radio over fiber (RoF) system with 10 Gbit/s 4-pulse amplitude modulation (4 PAM) transmission signal is proposed and simulated. 10 Gbit/s electrical 4 PAM signals modulated are conveyed over the length of 40 km standard single mode fiber (SMF) and recovered via the self-mixing technique after detecting directly at the receiver. Graphs of time-domain wave, frequency-domain and optical spectrum are measured out in different period, and the comparison of error vector magnitude curves of NRZ and 4 PAM signals under the different length of fiber is accomplished. The capacity of 4 PAM modulation is higher, though NRZ performs better than 4 PAM selected in RoF system within 80 km of fiber length as shown in the simulation results.
基金supported by the National Natural Science Foundation of China(No.62005234)the China Scholarship Council Post-Doctoral Program(No.202107230002)the Natural Science Foundation of Hunan Province(No.2024JJ6434).
文摘In this work,we propose a method using frequency-modulated continuous-wave(FMCW)self-mixing interferometry(SMI)and all-phase fast Fourier transform(APFFT)for simultaneous measurement of speed and distance.APFFT offers superior accuracy in frequency determination by mitigating issues like the fence effect and spectrum leakage,contributing to the high-accuracy measurement for speed and distance.Both simulations and experiments have demonstrated relative errors at the levels of 10^(−4) and 10^(−3) for distance and speed measurements,respectively.Furthermore,factors impacting measurement performance have been discussed.The proposed method provides a high-performance and cost-effective solution for distance and speed measurements,applicable across scientific research and various industrial domains.
基金supported by the National Natural Science Foundation of China(Nos.61905005 and 52175375)the General Program of Science and Technology Development Project of Beijing Municipal Education Commission(No.KM202110005004)。
文摘The self-mixing interferometry(SMI)technique is an emerging sensing technology in microscale particle classification.However,due to the nature of the SMI effect raised by a microscattering particle,the signal analysis suffers from many problems compared with a macro target,such as lower signal-to-noise ratio(SNR),short transit time,and time-varying modulation strength.Therefore,the particle sizing measurement resolution is much lower than the one in typical displacement measurements.To solve these problems,in this paper,first,a theoretical model of the phase variation of a singleparticle SMI signal burst is demonstrated in detail.The relationship between the phase variation and the particle size is investigated,which predicts that phase observation could be another alternative for particle detection.Second,combined with continuous wavelet transform and Hilbert transform,a novel phase-unwrapping algorithm is proposed.This algorithm can implement not only efficient individual burst extraction from the noisy raw signal,but also precise phase calculation for particle sizing.The measurement shows good accuracy over a range from 100 nm to 6μm with our algorithm,proving that our algorithm enables a simple and reliable quantitative particle characteristics retrieval and analysis methodology for microscale particle detection in biomedical or laser manufacturing fields.
基金the National Natural Science Foundation of China(No.61803281)the Natural Science Foundation of Tianjin(Nos.18JCQNJC75500 and 18JCQNJC71200)the Scientific Research Project of Tianjin Education Commission(Nos.2017KJ253 and 2018KJ136).
文摘In order to achieve the accurate measurement of displacement, this Letter presents a self-mixing interference displacement measurement method suitable for the speckle effect. Because of the speckle effect, the amplitude of the self-mixing interference signal fluctuates greatly, which will affect the measurement accuracy of displacement. The ensemble empirical mode decomposition is used to process the interference signal, which can filter out high-frequency noise and low-frequency noise at the same time. The envelope of the self-mixing interference signal is extracted by Hilbert transform, and it is used to realize the normalization of the signal. Through a series of signal processing, the influence of speckle can be effectively reduced, and the self-mixing interference signal can be transformed into standard form. The displacement can be reconstructed by fringe counting and the interpolation method. The experimental results show that the method is successfully applied to the displacement measurement in the presence of speckle, which verifies the effectiveness and feasibility of the method.
基金supported by the Northeast Petroleum University Youth Science Foundation(No.2020QNL-13)。
文摘An improved self-mixing grating interferometer based on the Littrow structure has been proposed in this Letter to measure displacement.The grating is integrated inside the interferometer to reduce the impact on the vibration parameters of the object caused by the grating attached to the vibrating object.The+1 st diffracted light returns to the laser cavity after being reflected by the target object,and self-mixing interference occurs.The displacement can be reconstructed by processing the self-mixing signals.The feasibility of the proposed interferometer is demonstrated by experimental measurements,and results show that it can achieve micro displacement measurement with the maximum absolute errors of less than 50 nm.
基金This work was supported by the National Natural Science Foundation of China （Grant No. 91123015, 51405240）, the Specialized Research Fund for the Doctoral Program of Higher Education （20113207110004）, and the Natural Science Foundation of Jiangsu Province（BK20140925）. Open Access This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author（s） and source are credited.
文摘Micro-displacement measurement based on self-mixing interference using a fiber laser system was demonstrated. The sinusoidal phase modulation technique was introduced into the fiber laser self-mixing interference measurement system to improve the measurement resolution. The phase could be demodulated by the Fourier analysis method. Error sources were evaluated in detail, and the system was experimentally applied to reconstruct the motion of a high-precision commercial piezoelectric ceramic transducer （PZT）. The displacement measurement resolution was well beyond a half-wavelength. It provides a practical solution for displacement measurement based on all optical-fiber sensing applications with high precision.
基金supported by the National Natural Science Foundation of China(Nos.61675174 and 61308048)
文摘A self-mixing interferometer(SMI)with resolution twenty times higher than that of a conventional interferometer is developed by multiple reflections.Only by employing a simple external reflecting mirror,the multiple-pass optical configuration can be constructed.The advantage of the configuration is simple and easy to make the light re-injected back into the laser cavity.Theoretical analysis shows that the resolution of measurement is scalable by adjusting the number of reflections.The experiment shows that the proposed method has the optical resolution of approximateλ/40.The influence of displacement sensitivity gain(G)is further analyzed and discussed in practical experiments.
文摘Self-mixing interferometry(SMI)is an attractive sensing scheme that typically relies on mono-modal operation of an employed laser diode.However,change in laser modality can occur due to change in operating conditions.So,detection of occurrence of multi-modality in SMI signals is necessary to avoid erroneous metric measurements.Typically,processing of multi-modal SMI signals is a difficult task due to the diverse and complex nature of such signals.However,the proposed techniques can significantly ease this task by identifying the modal state of SMI signals with 100%success rate so that interferometric fringes can be correctly interpreted for metric sensing applications.
基金supported by the National Natural Science Foundation of China (No.61675174)the Natural Science Foundation of Fujian Province (No.2020J01705)。
文摘In this paper, we present a method based on self-mixing interferometry combing extreme learning machine for real-time human blood pressure measurement. A signal processing method based on wavelet transform is applied to extract reversion point in the self-mixing interference signal, thus the pulse wave profile is successfully reconstructed. Considering the blood pressure values are intrinsically related to characteristic parameters of the pulse wave, 80 samples from the MIMIC-II database are used to train the extreme learning machine blood pressure model. In the experiment, 15 measured samples of pulse wave signal are used as the prediction sets. The results show that the errors of systolic and diastolic blood pressure are both within 5 mm Hg compared with that by the Coriolis method.
基金supported by the National Natural Science Foundation of China under Grant Nos.61275165,61201401,and 61307098
文摘Based on a single-channel laser self-mixing interferometcr, we present a new silnultaneous measurement of the vibration amplitude and tile rotation angle of objects that both affect the power spectrum containing two peaks of the interferometer signals. The fitted results indicate that the curve of the peak frequency versus the vibration amplitude follows a linear distribution, and the curve of the difference of the two-peak power values versus the angle follows a Gaussian distribution. A vibration amplitude with an error less than 3.0% and a rotation angle with an error less than 11.7% are calculated from the fitted results.
文摘At the mirrors of a laser diode self-mixing interferometer,the output beams carry anti-correlated(i.e.f in phase opposition)interferometric signals,whereas the superposed noise fluctuations are(partially)correlated.Therefore,by using an instrumental output of the interferometer as the difference of the two,we double the amplitude of the self-mixing useful signal,while the superposed noise is reduced.To validate the idea,we first calculate the noise reduction by means of a second-quantization model,finding that in a laser diode the signal-to-noise ratio(SNR)can be improved by 8.2 dB,typically.Then,we also carry out an experimental measurement of SNR and find very good agreement with the theoretical result.
文摘Laser self-mixing interferometer has the advantages of simple architecture, compact size, naturally self-aligned optical characteristics, and low cost. It is promising to replace conventional interferometers for physical measurements, such as displacement, distance, velocity, vibration, and so on. In this paper, this interferometer was tried to be used for micro-electro- mechanical system （MEMS） dynamic measurement. Firstly, its measurement principle based on a three-mirror cavity model was presented, and then the laser self-mixing interferometer for MEMS dynamic measurement was designed, experiments were finally performed as target moves with different forms. Experimental results suggest that self-mixing interferometer is available for MEMS dynamic measurement, and may have wider applications in the future.
基金supported by the Natural Science Foundation of Fujian Province(No.2020J01705)the School Foundation of Jimei University(No.C150345)。
文摘In this paper,we present a phase multiplication algorithm(PMA)to obtain scalable fringe precision in laser self-mixing interferometer under a weak feedback regime.Merely by applying the double angle formula on the self-mixing signal multiple times,the continuously improved fringe precision will be obtained.Theoretical analysis shows that the precision of the fringe could be improved toλ/2^(n+1).The validity of the proposed method is demonstrated by means of simulated SMI signals and confirmed by experiments under different amplitudes.A fringe precision ofλ/128 at a sampling rate of 500 k S/s has been achieved after doing 6 th the PMA.Finally,an amplitude of 50 nm has been proved to be measurable and the absolute error is 3.07 nm,which is within the theoretical error range.The proposed method for vibration measurement has the advantage of high accuracy and reliable without adding any additional optical elements in the optical path,thus it will play an important role in nanoscale measurement field.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61271157,61401456,and 11403084)Jiangsu Provincial Planned Projects for Postdoctoral Research Funds(Grant No.1301054B)+4 种基金the Fund from Suzhou Industry Technology Bureau(Grant No.ZXG2012024)China Postdoctoral Science Foundation(Grant No.2014M551678)the Graduate Student Innovation Program for Universities of Jiangsu Province(Grant No.CXLX12-0724)the Fundamental Research Funds for the Central Universities(Grant No.JUDCF 12032)the Fund from National University of Defense Technology(Grant No.JC13-02-14)
文摘We report the fabrication and characterization of a single-layer graphene field-effect terahertz detector, which is cou- pled with dipole-like antennas based on the self-mixing detector model. The graphene is grown by chemical vapor deposi- tion and then transferred onto an SiO2/Si substrate. We demonstrate room-temperature detection at 237 GHz. The detector could offer a voltage responsivity of 0.1 V/W and a noise equivalent power of 207 nW/Hz 1/2. Our modeling indicates that the observed photovoltage in the p-type gated channel can be well fit by the self-mixing theory. A different photoresponse other than self-mixing may apply for the n-type gated channel.
