The Stinger PDC cutter has high rock-breaking efficiency and excellent impact and wear resistance, which can significantly increase the rate of penetration (ROP) and extend PDC bit life for drilling hard and abrasive ...The Stinger PDC cutter has high rock-breaking efficiency and excellent impact and wear resistance, which can significantly increase the rate of penetration (ROP) and extend PDC bit life for drilling hard and abrasive formation. The knowledge of force response and mechanical specific energy (MSE) for the Stinger PDC cutter is of great importance for improving the cutter's performance and optimizing the hybrid PDC bit design. In this paper, 87 single cutter tests were conducted on the granite. A new method for precisely obtaining the rock broken volume was proposed. The influences of cutting depth, cutting angle, and cutting speed on cutting force and MSE were analyzed. Besides, a phenomenological cutting force model of the Stinger PDC cutter was established by regression of experimental data. Moreover, the surface topography and fracture morphology of the cutting groove and large size cuttings were measured by a 3D profilometer and a scanning electron microscope (SEM). Finally, the rock-breaking mechanism of the Stinger PDC cutter was illustrated. The results indicated that the cutting depth has the greatest influence on the cutting force and MSE, while the cutting speed has no obvious effects, especially at low cutting speeds. As the increase of cutting depth, the cutting force increases linearly, and MSE reduces with a quadratic polynomial relationship. When the cutting angle raises from 10° to 30°, the cutting force increases linearly, and the MSE firstly decreases and then increases. The optimal cutting angle for breaking rock is approximately 20°. The Stinger PDC cutter breaks granite mainly by high concentrated point loading and tensile failure, which can observably improve the rock breaking efficiency. The key findings of this work will help to reveal the rock-breaking mechanisms and optimize the cutter arrangement for the Stinger PDC cutter.展开更多
A heavy-ion irradiation experiment is studied in digital storage cells with different design approaches in 130？nm CMOS bulk Si and silicon-on-insulator （SOI） technologies. The effectiveness of linear energy transf...A heavy-ion irradiation experiment is studied in digital storage cells with different design approaches in 130？nm CMOS bulk Si and silicon-on-insulator （SOI） technologies. The effectiveness of linear energy transfer （LET） with a tilted ion beam at the 130？nm technology node is obtained. Tests of tilted angles θ=0 ° , 30 ° and 60 ° with respect to the normal direction are performed under heavy-ion Kr with certain power whose LET is about 40？MeVcm 2 /mg at normal incidence. Error numbers in D flip-flop chains are used to determine their upset sensitivity at different incidence angles. It is indicated that the effective LETs for SOI and bulk Si are not exactly in inverse proportion to cosθ , furthermore the effective LET for SOI is more closely in inverse proportion to cosθ compared to bulk Si, which are also the well known behavior. It is interesting that, if we design the sample in the dual interlocked storage cell approach, the effective LET in bulk Si will look like inversely proportional to cosθ very well, which is also specifically explained.展开更多
The HT-7U tokamak is a magnetically-confined full superconducting fusion device, consisting of superconducting toroidal field (TF) coils and superconducting poloidal field (PF) coils. These coils are wound with cable-...The HT-7U tokamak is a magnetically-confined full superconducting fusion device, consisting of superconducting toroidal field (TF) coils and superconducting poloidal field (PF) coils. These coils are wound with cable-in-conductor (CICC) which is based on UNK NbTi wires made in Russian '. A single D-shaped toroidal field magnet coil will be tested for large and expensive magnets systems before assembling them in the toroidal configuration. This paper describes the layout of the instrumentation for a superconducting test facility based on the results of a finite element modeling of the single coil of toroidal magnetic field (TF) coils in HT-7U tokamak device. At the same time, the design of coil support structure in the test facility is particularly discussed in some detail.展开更多
Ion photon emission microscopy （IPEM） is a new ion-induced emission microscopy. It employs a broad ion beam with high energy and low fluence rate impinging on a sample. The position of a single ion is detected by an...Ion photon emission microscopy （IPEM） is a new ion-induced emission microscopy. It employs a broad ion beam with high energy and low fluence rate impinging on a sample. The position of a single ion is detected by an optical system with objective lens, prism, microscope tube and charge coupled device （CCD）. A thin ZnS film doped with Ag ions is used as a luminescent material. Generation efficiency and transmission efficiency of photons in the ZnS（Ag） film created by irradiated Cl ions are calculated. A single Cl ion optical microscopic image is observed by high quantum efficiency CCD. The resolution of a single Cl ion given in this IPEM system is 6μm. Several factors influencing the resolution are discussed. A silicon diode is used to collect the electrical signals caused by the incident ions. Effective and accidental coincidence of optical images and electronic signals are illustrated. A two-dimensional map of single event effect is drawn out according to the data of effective coincidence.展开更多
This research investigates the mechanical and thermal properties of Morus alba combined with polylactic acid in comparison with other natural fibers. The study uses three different fiber and PLA compositions - 20%, 30...This research investigates the mechanical and thermal properties of Morus alba combined with polylactic acid in comparison with other natural fibers. The study uses three different fiber and PLA compositions - 20%, 30%, and 40% respectively - to produce composite materials. In addition, another composite with the same fiber volume is treated with a 4% NaOH solution to improve mechanical properties. The composites are processed by twin-screw extrusion, granulation, and injection molding. Tensile strength measurements of raw fibers and NaOH-treated fibers were carried out using a single-fiber tensile test with a gauge length of 40 mm. It was observed that the NaOH surface treatment increases the resistance against tensile loading and exhibited improved properties for raw fiber strands. The diameter of the fibers was measured using optical microscopy. During this research, flexural tests, impact tests, differential scanning calorimetry (DSC), and heat deflection temperature measurements (HDT) were conducted to evaluate the mechanical and thermal properties of the developed composite samples. The results indicate that the mechanical properties of NaOH-treated Morus alba-reinforced polylactic acid outperform both virgin PLA samples and untreated Morus alba samples.展开更多
The high concentrations of Fe^(2+) and Mn^(2+) in acid mine drainage make it difficult and expensive to treat.It is urgent that we find a cheap and efficient adsorption material to treat Fe^(2+) and Mn^(2+).As a solid...The high concentrations of Fe^(2+) and Mn^(2+) in acid mine drainage make it difficult and expensive to treat.It is urgent that we find a cheap and efficient adsorption material to treat Fe^(2+) and Mn^(2+).As a solid waste in mining areas,coal gangue occupies a large area and pollutes the surrounding environment during the stacking process.Developing a method of resource utilization is thus a research hotspot.In this study,we modified spontaneous combustion gangue using NaOH,NaCl,and HCl by chemically modifying the minerals.We determined the optimal conditions for treating Fe^(2+) and Mn^(2+) in acid mine drainage with spontaneous combustion gangue and modified coal gangue using the single factor test method.Based on results of the static test,two dynamic test columns,column No.1(spontaneous combustion gangue)and column No.2(NaOH modified spontaneous combustion gangue),were constructed,and the repair effects of acid mine drainage were compared and analyzed using dynamic experiments.The results show that overall,NaOH modified spontaneous combustion gangue is the most efficient at removing the Fe^(2+) and Mn^(2+) in acid mine drainage.The optimal conditions for NaOH modification are an NaOH concentration of 3 mol/L,a liquid to solid ratio of 2 L/kg,and a modification time of 8 h.The overall efficiency of column No.2 at removing Fe^(2+) and Mn^(2+) from acid mine drainage is better than that of column No.1.Among them,the average removal efficiency of Fe^(2+)and Mn^(2+) from acid mine drainage in column No.2 were 97.73%and 44.82%,respectively.The above results show that NaOH modified spontaneous combustion gangue is a good adsorbent,which has application potential in wastewater remediation,as it can achieve the purpose of“treating dust with waste”.展开更多
Fuel cells are considered to be one of the ideal alternatives to traditional fossil energy conversion devices.Membrane electrodes are the core components in the hydrogen fuel cells.Our work reported the synthesis of t...Fuel cells are considered to be one of the ideal alternatives to traditional fossil energy conversion devices.Membrane electrodes are the core components in the hydrogen fuel cells.Our work reported the synthesis of the Pt/C catalysts with different Pt loading,and by changing the Nafion content,hot pressing temperature and hot pressing pressure,the catalyst coated membrane(CCM)spraying process was optimized.Moreover,the three-dimensional structure model of the single battery membrane electrode was studied quantitatively,and the porous membrane electrode with gradient distribution was fabricated under optimized processing conditions,with excellent electrical performance.展开更多
The validity of Local Cubic Law （LCL） is an important issue to study groundwater flow and transport in fractured media. According to laboratory simulaion tests, the average velocity with a lower gradient in a single...The validity of Local Cubic Law （LCL） is an important issue to study groundwater flow and transport in fractured media. According to laboratory simulaion tests, the average velocity with a lower gradient in a single fracture is calculated by the LCL, which is compared with the measured average velocity. Then dye tracer test is designed and completed. The evidence for non-LCL, is drawn from the results of the simulation tests and the dye tracer tests. Then the Reynolds number of groundwater is calculated, the critical value of Re for laminar flow is discussed in a single fracture under different conditions. The motion types for groundwater flow have been discussed.展开更多
[ Objective ] This study aimed to establish and optimize the ISSR-PCR reaction system and amplification process for Elymus sibiricus L. , to provide sci- entific basis for exploring the genetic diversity of E. sibiric...[ Objective ] This study aimed to establish and optimize the ISSR-PCR reaction system and amplification process for Elymus sibiricus L. , to provide sci- entific basis for exploring the genetic diversity of E. sibiricus germplasm resources. [ Method] Orthogonal design and single factor test were applied to establish the ISSR-PCR reaction system of E. sibiricus, optimize the influencing factors including Taq DNA polymerase, DNA template concentration, Mg2 ＋ , dNTP, primer concentration, and screen the annealing temperature, number of cycles and extension time. [ Result ] The optimal reaction system for ISSR analysis contains 0.2 mmol/L dNTPs, 0.2 μmol/L ISSR primers, 1.5 U of Taq DNA polymerase, 2.5 μl of 10 × PCR Buffer, 1.5 mmol/L MgC12 and 40 ng of template DNA in 25 μl total volume; the amplification was conducted with 35 cycles and extension time of 90 s. [ Conclusion] ISSR-PCR reaction system for E. sibiricus was established and optimized, and then verified using two E. sibiricus germplasrns, demonstrating that the ISSR-PCR reaction system is stable and can be used for the genetic analysis of E. sibiricus.展开更多
The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the...The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the pre-salt carbonate rock. This work presents the results of numerical modeling through finite element method and discrete element method for single cutter drilling in carbonate samples. The work is relevant to understand the mechanics of drill bit-rock interaction while drilling deep wells and the results were validated with experimental data raised under simulated downhole conditions. The numerical models were carried out under different geometrical configurations, varying the cutter chamfer size and back-rake angles. The forces generated on the cutter are translated into mechanical specific energy as this parameter is often used to measure drilling efficiency. Results indicate that the chamfer size does not change significantly the mechanical specific energy values, characteristic. Results also show there is a significant increase although the cutter aggressiveness is influenced by this geometrical in drilling resistance for larger values of back-rake angle.展开更多
The element-release behavior of municipal solid waste incineration fly ash was explored through leaching test with continuous set-point pH(pH_(stat) test)and serial single reaction cell(SSRC)tests.First,the relationsh...The element-release behavior of municipal solid waste incineration fly ash was explored through leaching test with continuous set-point pH(pH_(stat) test)and serial single reaction cell(SSRC)tests.First,the relationship between element release and acid neutralizing capacity(ANC)consumption was examined with a pHstat test.Four types of release behaviors were identified which are characteristic for different elements:(1)release curves that were almost linear with ANC consumption(Ca,Zn,and Cd);(2)release that was significantly faster than ANC(Na,K,and Cl);(3)curves that featured a strong increase with ANC consumption,after a transient release,followed by an almost equal decrease(Si and S);and(4)release that is strongly retarded compared with ANC consumption(Cr,Cu,and Pb).In the SSRC system,it the existence of a pH front and a wash-out phenomenon is demonstrated.Combining the results from the SSRC test with the kinetic analysis of the ANC system in the pH_(stat) test,it was inferred that less than one-third of the ANC measured from a batch pH titration plays a neutralization role in a field situation.The methodologies described may provide a powerful set of tools for systematic evaluation of element release from solid wastes.展开更多
A new triaxial testing system that could control suction in wetting-induced collapsible tests was success-fully developed to study the suction effects on wetting-induced collapsible deformation.The pedestal of the tri...A new triaxial testing system that could control suction in wetting-induced collapsible tests was success-fully developed to study the suction effects on wetting-induced collapsible deformation.The pedestal of the triaxial cell was made up of two parts,and the equipment not only could control suction but also could make water accessible to soil.A pressure/volume-controlled equip-ment was combined with the triaxial system to measure the water volume absorbed by samples accurately and to add pressure on water to filtrate into the sample.The apparatus could measure volume change precisely and keep the deviator stress unvaried,as well as measure the volume of water filtrating into the samples exactly.A triaxial collapsible testing procedure was described using the new apparatus for undisturbed collapsible loess with controlled suction.Furthermore,a series of double triaxial collapsible tests were conducted under different suctions and the same net cell pressure,and tests under different net cell pressures and the same suction were also done.It was indicated that the collapsible deformation increased with the increasing suction,and the effect of the net cell pressure on collapsible deformation was remarkable.The new triaxial apparatus was a useful facility to study the collapsible behavior of loess.展开更多
基金supported by the Joint Funds of The National Natural Science Foundation of China(Grant No.U19B6003-05)the National Key Research and Development Program of China(No.2019YFA0708302)+2 种基金the National Science Fund for Distinguished Young Scholars(Grant No.51725404)the Beijing Outstanding Young Scientist Program(Grant No.BJJWZYJH01201911414038)the Strategic Cooperation Technology Projects of CNPC and CUPB(Grant No.ZLZX2020-01).
文摘The Stinger PDC cutter has high rock-breaking efficiency and excellent impact and wear resistance, which can significantly increase the rate of penetration (ROP) and extend PDC bit life for drilling hard and abrasive formation. The knowledge of force response and mechanical specific energy (MSE) for the Stinger PDC cutter is of great importance for improving the cutter's performance and optimizing the hybrid PDC bit design. In this paper, 87 single cutter tests were conducted on the granite. A new method for precisely obtaining the rock broken volume was proposed. The influences of cutting depth, cutting angle, and cutting speed on cutting force and MSE were analyzed. Besides, a phenomenological cutting force model of the Stinger PDC cutter was established by regression of experimental data. Moreover, the surface topography and fracture morphology of the cutting groove and large size cuttings were measured by a 3D profilometer and a scanning electron microscope (SEM). Finally, the rock-breaking mechanism of the Stinger PDC cutter was illustrated. The results indicated that the cutting depth has the greatest influence on the cutting force and MSE, while the cutting speed has no obvious effects, especially at low cutting speeds. As the increase of cutting depth, the cutting force increases linearly, and MSE reduces with a quadratic polynomial relationship. When the cutting angle raises from 10° to 30°, the cutting force increases linearly, and the MSE firstly decreases and then increases. The optimal cutting angle for breaking rock is approximately 20°. The Stinger PDC cutter breaks granite mainly by high concentrated point loading and tensile failure, which can observably improve the rock breaking efficiency. The key findings of this work will help to reveal the rock-breaking mechanisms and optimize the cutter arrangement for the Stinger PDC cutter.
基金Supported by the Key Laboratory of Microsatellites,Chinese Academy of Sciences
文摘A heavy-ion irradiation experiment is studied in digital storage cells with different design approaches in 130？nm CMOS bulk Si and silicon-on-insulator （SOI） technologies. The effectiveness of linear energy transfer （LET） with a tilted ion beam at the 130？nm technology node is obtained. Tests of tilted angles θ=0 ° , 30 ° and 60 ° with respect to the normal direction are performed under heavy-ion Kr with certain power whose LET is about 40？MeVcm 2 /mg at normal incidence. Error numbers in D flip-flop chains are used to determine their upset sensitivity at different incidence angles. It is indicated that the effective LETs for SOI and bulk Si are not exactly in inverse proportion to cosθ , furthermore the effective LET for SOI is more closely in inverse proportion to cosθ compared to bulk Si, which are also the well known behavior. It is interesting that, if we design the sample in the dual interlocked storage cell approach, the effective LET in bulk Si will look like inversely proportional to cosθ very well, which is also specifically explained.
基金The project supported by the National Meg-Science Enineering Project of Chinese Government
文摘The HT-7U tokamak is a magnetically-confined full superconducting fusion device, consisting of superconducting toroidal field (TF) coils and superconducting poloidal field (PF) coils. These coils are wound with cable-in-conductor (CICC) which is based on UNK NbTi wires made in Russian '. A single D-shaped toroidal field magnet coil will be tested for large and expensive magnets systems before assembling them in the toroidal configuration. This paper describes the layout of the instrumentation for a superconducting test facility based on the results of a finite element modeling of the single coil of toroidal magnetic field (TF) coils in HT-7U tokamak device. At the same time, the design of coil support structure in the test facility is particularly discussed in some detail.
基金Supported by the National Natural Science Foundation of China under Grant No 11690044
文摘Ion photon emission microscopy （IPEM） is a new ion-induced emission microscopy. It employs a broad ion beam with high energy and low fluence rate impinging on a sample. The position of a single ion is detected by an optical system with objective lens, prism, microscope tube and charge coupled device （CCD）. A thin ZnS film doped with Ag ions is used as a luminescent material. Generation efficiency and transmission efficiency of photons in the ZnS（Ag） film created by irradiated Cl ions are calculated. A single Cl ion optical microscopic image is observed by high quantum efficiency CCD. The resolution of a single Cl ion given in this IPEM system is 6μm. Several factors influencing the resolution are discussed. A silicon diode is used to collect the electrical signals caused by the incident ions. Effective and accidental coincidence of optical images and electronic signals are illustrated. A two-dimensional map of single event effect is drawn out according to the data of effective coincidence.
文摘This research investigates the mechanical and thermal properties of Morus alba combined with polylactic acid in comparison with other natural fibers. The study uses three different fiber and PLA compositions - 20%, 30%, and 40% respectively - to produce composite materials. In addition, another composite with the same fiber volume is treated with a 4% NaOH solution to improve mechanical properties. The composites are processed by twin-screw extrusion, granulation, and injection molding. Tensile strength measurements of raw fibers and NaOH-treated fibers were carried out using a single-fiber tensile test with a gauge length of 40 mm. It was observed that the NaOH surface treatment increases the resistance against tensile loading and exhibited improved properties for raw fiber strands. The diameter of the fibers was measured using optical microscopy. During this research, flexural tests, impact tests, differential scanning calorimetry (DSC), and heat deflection temperature measurements (HDT) were conducted to evaluate the mechanical and thermal properties of the developed composite samples. The results indicate that the mechanical properties of NaOH-treated Morus alba-reinforced polylactic acid outperform both virgin PLA samples and untreated Morus alba samples.
基金This work was supported by the National Natural Science Foundation of China(Nos.51304114,41672247)the Scientific Research Fund of the Liaoning Provincial Education Department(No.LJ2017FAL016).
文摘The high concentrations of Fe^(2+) and Mn^(2+) in acid mine drainage make it difficult and expensive to treat.It is urgent that we find a cheap and efficient adsorption material to treat Fe^(2+) and Mn^(2+).As a solid waste in mining areas,coal gangue occupies a large area and pollutes the surrounding environment during the stacking process.Developing a method of resource utilization is thus a research hotspot.In this study,we modified spontaneous combustion gangue using NaOH,NaCl,and HCl by chemically modifying the minerals.We determined the optimal conditions for treating Fe^(2+) and Mn^(2+) in acid mine drainage with spontaneous combustion gangue and modified coal gangue using the single factor test method.Based on results of the static test,two dynamic test columns,column No.1(spontaneous combustion gangue)and column No.2(NaOH modified spontaneous combustion gangue),were constructed,and the repair effects of acid mine drainage were compared and analyzed using dynamic experiments.The results show that overall,NaOH modified spontaneous combustion gangue is the most efficient at removing the Fe^(2+) and Mn^(2+) in acid mine drainage.The optimal conditions for NaOH modification are an NaOH concentration of 3 mol/L,a liquid to solid ratio of 2 L/kg,and a modification time of 8 h.The overall efficiency of column No.2 at removing Fe^(2+) and Mn^(2+) from acid mine drainage is better than that of column No.1.Among them,the average removal efficiency of Fe^(2+)and Mn^(2+) from acid mine drainage in column No.2 were 97.73%and 44.82%,respectively.The above results show that NaOH modified spontaneous combustion gangue is a good adsorbent,which has application potential in wastewater remediation,as it can achieve the purpose of“treating dust with waste”.
基金This work was financially supported by China Petrochemical Corporation(ST 20006-1,ST 20006-2).
文摘Fuel cells are considered to be one of the ideal alternatives to traditional fossil energy conversion devices.Membrane electrodes are the core components in the hydrogen fuel cells.Our work reported the synthesis of the Pt/C catalysts with different Pt loading,and by changing the Nafion content,hot pressing temperature and hot pressing pressure,the catalyst coated membrane(CCM)spraying process was optimized.Moreover,the three-dimensional structure model of the single battery membrane electrode was studied quantitatively,and the porous membrane electrode with gradient distribution was fabricated under optimized processing conditions,with excellent electrical performance.
基金Project supported by the National Natural Science Foundation of China (Grant No :40202027) and Fok Ying Tung Ed-ucation Foundation (Grant No :91079)
文摘The validity of Local Cubic Law （LCL） is an important issue to study groundwater flow and transport in fractured media. According to laboratory simulaion tests, the average velocity with a lower gradient in a single fracture is calculated by the LCL, which is compared with the measured average velocity. Then dye tracer test is designed and completed. The evidence for non-LCL, is drawn from the results of the simulation tests and the dye tracer tests. Then the Reynolds number of groundwater is calculated, the critical value of Re for laminar flow is discussed in a single fracture under different conditions. The motion types for groundwater flow have been discussed.
基金Supported by Project of Collection,Cataloguing and Utilization of Perennial Forage Grass Germplasm Resources(NB2012-2130135-33)Conservation Project for Forage Grass Germplasm Resources
文摘[ Objective ] This study aimed to establish and optimize the ISSR-PCR reaction system and amplification process for Elymus sibiricus L. , to provide sci- entific basis for exploring the genetic diversity of E. sibiricus germplasm resources. [ Method] Orthogonal design and single factor test were applied to establish the ISSR-PCR reaction system of E. sibiricus, optimize the influencing factors including Taq DNA polymerase, DNA template concentration, Mg2 ＋ , dNTP, primer concentration, and screen the annealing temperature, number of cycles and extension time. [ Result ] The optimal reaction system for ISSR analysis contains 0.2 mmol/L dNTPs, 0.2 μmol/L ISSR primers, 1.5 U of Taq DNA polymerase, 2.5 μl of 10 × PCR Buffer, 1.5 mmol/L MgC12 and 40 ng of template DNA in 25 μl total volume; the amplification was conducted with 35 cycles and extension time of 90 s. [ Conclusion] ISSR-PCR reaction system for E. sibiricus was established and optimized, and then verified using two E. sibiricus germplasrns, demonstrating that the ISSR-PCR reaction system is stable and can be used for the genetic analysis of E. sibiricus.
文摘The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the pre-salt carbonate rock. This work presents the results of numerical modeling through finite element method and discrete element method for single cutter drilling in carbonate samples. The work is relevant to understand the mechanics of drill bit-rock interaction while drilling deep wells and the results were validated with experimental data raised under simulated downhole conditions. The numerical models were carried out under different geometrical configurations, varying the cutter chamfer size and back-rake angles. The forces generated on the cutter are translated into mechanical specific energy as this parameter is often used to measure drilling efficiency. Results indicate that the chamfer size does not change significantly the mechanical specific energy values, characteristic. Results also show there is a significant increase although the cutter aggressiveness is influenced by this geometrical in drilling resistance for larger values of back-rake angle.
基金This research was partially funded by the National Natural Science Foundation of China(Grant No.20777044).
文摘The element-release behavior of municipal solid waste incineration fly ash was explored through leaching test with continuous set-point pH(pH_(stat) test)and serial single reaction cell(SSRC)tests.First,the relationship between element release and acid neutralizing capacity(ANC)consumption was examined with a pHstat test.Four types of release behaviors were identified which are characteristic for different elements:(1)release curves that were almost linear with ANC consumption(Ca,Zn,and Cd);(2)release that was significantly faster than ANC(Na,K,and Cl);(3)curves that featured a strong increase with ANC consumption,after a transient release,followed by an almost equal decrease(Si and S);and(4)release that is strongly retarded compared with ANC consumption(Cr,Cu,and Pb).In the SSRC system,it the existence of a pH front and a wash-out phenomenon is demonstrated.Combining the results from the SSRC test with the kinetic analysis of the ANC system in the pH_(stat) test,it was inferred that less than one-third of the ANC measured from a batch pH titration plays a neutralization role in a field situation.The methodologies described may provide a powerful set of tools for systematic evaluation of element release from solid wastes.
文摘A new triaxial testing system that could control suction in wetting-induced collapsible tests was success-fully developed to study the suction effects on wetting-induced collapsible deformation.The pedestal of the triaxial cell was made up of two parts,and the equipment not only could control suction but also could make water accessible to soil.A pressure/volume-controlled equip-ment was combined with the triaxial system to measure the water volume absorbed by samples accurately and to add pressure on water to filtrate into the sample.The apparatus could measure volume change precisely and keep the deviator stress unvaried,as well as measure the volume of water filtrating into the samples exactly.A triaxial collapsible testing procedure was described using the new apparatus for undisturbed collapsible loess with controlled suction.Furthermore,a series of double triaxial collapsible tests were conducted under different suctions and the same net cell pressure,and tests under different net cell pressures and the same suction were also done.It was indicated that the collapsible deformation increased with the increasing suction,and the effect of the net cell pressure on collapsible deformation was remarkable.The new triaxial apparatus was a useful facility to study the collapsible behavior of loess.
