Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present ...Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present work a new spiral flow field with a bypass is proposed.The reaction gas enters the flow field in the central path and diffuses in two directions through the flow channel and the bypass.The bypasses are arranged incrementally.The number of bypasses and the cross-section size of the bypasses are varied parametrically while a single-cell model of the PEMFC is used.The influence of the concentration of liquid water and oxygen in the cell on the performance of different flow fields is determined by means of Computational fluid dynamics(COMSOL Multiphysics software).Results show that when the bypass number is 48 and its cross-sectional area is 0.5 mm^(2),the cell exhibits the best performances.展开更多
A subsurface flow wetland(SSFW)was simulated using a commercial computational fluid dynamic(CFD)code.The constructed media was simulated using porous media and the liquid resident time distribution(RTD)in the SSFW was...A subsurface flow wetland(SSFW)was simulated using a commercial computational fluid dynamic(CFD)code.The constructed media was simulated using porous media and the liquid resident time distribution(RTD)in the SSFW was obtained using the particle trajectory model.The effect of wetland configuration and operating conditions on the hydraulic performance of the SSFW were investigated.The results indicated that the hydraulic performance of the SSFW was predominantly affected by the wetland configuration.The hydraulic effciency of the SSFW with an inlet at the middle edge of the upper media was 0.584 and the best among the SSFWs with an inlet at the top,the middle,and the bottom edge of the upper media.The constructed media affected the hydraulic performance by the ratio(K)of the upper and lower media resistance.The selection of appropriate media resistance in the protection layer can improve the hydraulic effciency.When the viscous resistance coeffcient of the media in the protection layer changed from 2.315×105 to 1.200×108,the hydraulic effciency of the SSFW increased from 0.301 to 0.751.However,the effect of operating conditions on the hydraulic effciency of the SSFW was slight.展开更多
Subsurface water flow velocity influences the hydrodynamic characteristics of soil seepage and the interaction between subsurface water flow and surface runoff during soil erosion and sediment transport.A visualized m...Subsurface water flow velocity influences the hydrodynamic characteristics of soil seepage and the interaction between subsurface water flow and surface runoff during soil erosion and sediment transport.A visualized method and equipment was adopted in this study to observe the subsurface water flow.Quartz sand was used as the test material of subsurface water flow and fluorescent dye was used as the indicator for tracing subsurface water flow.Water was supplied at the same flow discharge to the three parts at the bottom of the test flume,and the subsurface water flow were determined with four slope gradients(4°,8°,10°,and 12°).The results showed that the seepage velocity gradually increased with increasing slope gradient.The pore water velocity at different depths of sand layer profile increased with increasing slope gradient,whereas the thickness of the flow front gradually decreased.For the same slope gradient,the pore water velocity in the lower layer was the largest,whereas the thickness of the flow front was the smallest.Comparative analysis of the relationship between seepage velocity and pore water velocity at different depths of sand layer profile showed that the maximum relative difference between the measured pore water velocity and the computational pore water velocity at different depths of sand profile in the experiment was 4.38%.Thus,the test method for measuring the subsurface water flow velocity of sand layer profile adopted in this study was effective and feasible.The development of this experiment and the exploration of research methods would lay a good test foundation for future studies on the variation law of subsurface water flow velocity and the determination of flow velocity in purple soils,thus contributing to the improvement of the hydrodynamic mechanism of purple soils.展开更多
As an important design factor for constructed wetlands,hydraulic retention time and its distribution will affect the treatment performance.Instantaneously injected sodium chloride tracers were used to obtain residence...As an important design factor for constructed wetlands,hydraulic retention time and its distribution will affect the treatment performance.Instantaneously injected sodium chloride tracers were used to obtain residence time distributions of the lab scale subsurface flow constructed wetland.Considering the presence of trailing and multiple peaks of the tracer breakthrough curve,the multi flow dispersion model(MFDM)was used to fit the experimental tracer breakthrough curves.According to the residual sum of squares and comparison between the experimental values and simulated values of the tracer concentration,MFDM could fit the residence time distribution(RTD)curve satisfactorily,the results of which also reflected the layered structure of wetland cells,thus to give reference for application of MFDM to the same kind of subsurface flow constructed wetlands.展开更多
The paper reports the findings of a research work carried out to examine the performance and efficiency of a subsurface constructed wetland (SSFCW) for the treatment of domestic sewage in the University of Lagos (Unil...The paper reports the findings of a research work carried out to examine the performance and efficiency of a subsurface constructed wetland (SSFCW) for the treatment of domestic sewage in the University of Lagos (Unilag), Nigeria. The removal patterns and efficiencies of the physical, chemical and biological sewage pollutants parameters of domestic waste water generated within Unilag community by the SSFCW were studied. The wastewater was sampled and analysed along the SSFCW from influent (point1) to effluent (point 11). Total Dissolved Solids (TDS) reduced from 471 mg/l to 11.85 mg/l (97.48%), Turbidity reduced from 108.75 HTU to 0.05HTU (99.95%), Manganese reduced from 6.05 mg/l to 0.61 mg/ (89.92%), Nitrate reduced from 27.5 mg/l to 2.0 mg/l (92.73%), Sulphate reduced from 48.5 mg/l to 28 mg/l (42.27%), Iron reduced from 1.13 mg/l to 0.03 mg/l (97.35%), BOD reduced from 73.14 mg/l to 12.8 mg/l (82.5%), and E-coli reduced from 874 MPN/100 ml to 0.15 MPN/100 ml (99.98%). On the other hand, Dissolved Oxygen content increased along the SSFCW from 3.14 mg/l to 7.49 mg/l (138.54%) while the pH improved from slightly acid level of 6.49 to slightly above neutral level of 7.05 (9.3%). All the parameters at effluent point are within the Nigerian Federal Environmental Protection Agency (FEPA) acceptable standard. The study concludes that the SSFCW is a cheap, efficient and appropriate technology for the treatment of domestic sewage under tropical conditions.展开更多
Subsurface water flow above the weakly permeable soil layer commonly occurs on purple soil slopes.However,it remains difficult to quantify the effect of subsurface water flow on the surface flow velocity.Laboratory ex...Subsurface water flow above the weakly permeable soil layer commonly occurs on purple soil slopes.However,it remains difficult to quantify the effect of subsurface water flow on the surface flow velocity.Laboratory experiments were performed to measure the rill flow velocity on purple soil slopes containing a subsurface water flow layer with the electrolyte tracer method considering 3 subsurface water flow depths(SWFDs:5,10,and 15 cm),3 flow rates(FRs:2,4,and 8 L min^(-1)),and 4 slope gradients(SGs:5°,10°,15°,and 20°).As a result,the pulse boundary model fit the electrolyte transport processes very well under the different SWFDs.The measured rill flow velocities were 0.202 to 0.610 m s^(-1) under the various SWFDs.Stepwise regression results indicated a positive dependence of the flow velocity on the FR and SG but a negative dependence on the SWFD.The SWFD had notable effects on the rill flow velocity.Decreasing the SWFD from 15 to 5 cm increased the flow velocity.Moreover,the flow velocities under the 10-and 15-cm SWFDs were 89%and 86%,respectively,of that under the 5-cm SWFD.The flow velocity under the 5-,10-and 15-cm SWFDs was decreased to 89%,80%,and 77%,respectively,of that on saturated soil slopes.The results will enhance the understanding of rill flow hydrological processes under SWFD impact.展开更多
The operational performance of a full scale subsurface flow constructed wetland, which treated the mixed industrial and domestic wastewater with BOD 5/COD mean ratio of 0 33 at Shatian, Shenzhen City was studied. The ...The operational performance of a full scale subsurface flow constructed wetland, which treated the mixed industrial and domestic wastewater with BOD 5/COD mean ratio of 0 33 at Shatian, Shenzhen City was studied. The constructed wetland system consists of screens, sump, pumping station, and primary settling basin, facultative pond, first stage wetland and secondary stage wetland. The designed treatment capacity is 5000 m 3/d, and the actual influent flow is in the range of <2000 to >10000 m 3/d. Under normal operational conditions, the final effluent quality well met the National Integrated Wastewater Discharge Standard（GB 8978\1996）, with the following parameters（mean values）: COD 33 90 mg/L, BOD 5 7.65 mg/L, TSS 7.92 mg/L, TN 9.11 mg/L and TP 0 56 mg/L. Seven species of plants were selected to grow in the wetland: Reed, Sweetcane flower Silvergrass, Great Bulrush, Powdery Thalia and Canna of three colours. The growing season is a whole year round. The seasonal discrepancy could be observed and the plants growing in the wetland are vulnerable to lower temperature in winter. The recycling of the effluent in the first stage of the wetland system is an effective measure to improve the performance of the wetland system. The insufficient DO value in the wetland system not only had significant effect on pollutants removal in the wetland, but also was unfavourable to plant growth. The recycling of effluent to the inlet of wetland system and artificial pond to increase DO value of influent to the wetland is key to operate the subsurface constructed wetland steadily and effectively.展开更多
Subsurface flow is a prominent runoff process in sloping lands of purple soil in the upper Yangtze River basin.However,it remains difficult to identify and quantify.In this study,in situ runoff experimental plots were...Subsurface flow is a prominent runoff process in sloping lands of purple soil in the upper Yangtze River basin.However,it remains difficult to identify and quantify.In this study,in situ runoff experimental plots were used to measure soil moisture dynamics using an array of time domain reflectometry(TDR) together with overland flow and subsurface flow using isolated collecting troughs.Frequency of preferential flow during rainfall events and the controls of subsurface flow processes were investigated through combined analysis of soil properties,topography,rainfall intensity,initial wetness,and tillage.Results showed that subsurface flow was ubiquitous in purple soil profiles due to welldeveloped macropores,especially in surface soils while frequency of preferential flow occurrence was very low(only 2 cases in plot C) during all 22 rainfall events.Dry antecedent moisture conditions promoted the occurrence of preferential flow.However,consecutive real-time monitoring of soil moisture at different depths and various slope positions implied the possible occurrence of multiple subsurface lateral flows during intensive storms.Rainfall intensity,tillage operation,and soil properties were recognized as main controls of subsurface flow in the study area,which allows the optimization of management practices for alleviating adverse environmental effects of subsurface flow in the region.展开更多
The flow maldistribution and the effect of different inlet configuration on the flow distribution in platefin heat exchangers were studied experimentally. It is found that the flow maldistribution is serious because o...The flow maldistribution and the effect of different inlet configuration on the flow distribution in platefin heat exchangers were studied experimentally. It is found that the flow maldistribution is serious because of the defects of inlet configurations, while the inlet configuration and Reynolds number are the main factors affecting the flow distribution. The improved inlet configurations, which are the header with a two-stage distributing configuration and the guide vane with a fluid complementary cavity were proposed and tested in this paper. The experimental results show that the improved inlet configurations can effectively improve the performance of flow distribution in heat exchangers.展开更多
In this paper the performance of a counter flow microchannel heat exchanger (CFMCHE) is numerically investigated with a nanofluid as a cooling medium. Two types of nanofluids are used Cu-water and Al2O3-water. From th...In this paper the performance of a counter flow microchannel heat exchanger (CFMCHE) is numerically investigated with a nanofluid as a cooling medium. Two types of nanofluids are used Cu-water and Al2O3-water. From the results obtained it’s found that thermal performance of CFMCHE increased with using the nanofluids as cooling medium with no extra increase in pressure drop due to the ultra fine solid particles and low volume fraction concentrations. The na-nofluids (Cu-water and Al2O3-water) volume fractions were in the range 1% to 5%. It’s also found that nanoflu-id-cooled CFMCHE could absorb more heat than water-cooled CFMCHE when the flow rate was low. For high flow rates the heat transfer was dominated by the volume flow rate and nanoparticles did not contribute to the extra heat absorption. Also the performance of CFMCHE can be increased considerably by using nanofluids with higher thermal conductivities.展开更多
Experiments in monitoring the removal of organic material and nitrogen and determining the amounts of mi- croorganism at different sites in the subsurface flow constructed wetland in Sihong county were performed. The ...Experiments in monitoring the removal of organic material and nitrogen and determining the amounts of mi- croorganism at different sites in the subsurface flow constructed wetland in Sihong county were performed. The results show that the removal of CODCr agrees with the kinetic equation of a first order reaction. The removal of pollutants varies with different seasons. The removal rates of CODCr, NH3-N, TN in the spring are 15%–23% higher than those in the autumn. The amount of ammonifier is larger than that of denitrifying bacteria and the amount of denitrifying bacte- ria is larger than that of nitrosomonas. The amount of bacteria around the plant roots is larger than that on the surface of the packing medium. No apparent change is observed for the amount of denitrifying bacteria and nitrosomonas between spring and autumn.展开更多
Objective To investigate the flow distribution in plate fin heat exchangers and optimize the design of header configuration for plate fin heat exchangers. Methods A mathematical model of header was proposed. The effec...Objective To investigate the flow distribution in plate fin heat exchangers and optimize the design of header configuration for plate fin heat exchangers. Methods A mathematical model of header was proposed. The effects of the header configuration on the flow distribution in plate fin heat exchangers were investigated by CFD. The second header configuration with a two stage distributing structure was brought forward to improve the performance of flow distribution. Results It is found that the flow maldistribution is very serious in the direction of header length for the conventional header used in industry. The numerical predictions indicate that the improved header configurations can effectively improve the performance of flow distribution in plate fin heat exchangers. Conclusion The numerical simulation confirms that CFD should be a suitable tool for predicting the flow distribution. The method has a wide variety of applications in the design of plate fin heat exchangers.展开更多
The aim of this study is to use a new configuration of porous media in a heat exchanger in continuous hydrothermal flow synthesis(CHFS)system to enhance the heat transfer and minimize the required length of the heat e...The aim of this study is to use a new configuration of porous media in a heat exchanger in continuous hydrothermal flow synthesis(CHFS)system to enhance the heat transfer and minimize the required length of the heat exchanger.For this purpose,numerous numerical simulations are performed to investigate performance of the system with porous media.First,the numerical simulation for the heat exchanger in CHFS system is validated by experimental data.Then,porous media is added to the system and six different thicknesses for the porous media are examined to obtain the optimum thickness,based on the minimum required length of the heat exchanger.Finally,by changing the flow rate and inlet temperature of the product as well as the cooling water flow rate,the minimum required length of the heat exchanger with porous media for various inlet conditions is assessed.The investigations indicate that using porous media with the proper thickness in the heat exchanger increases the cooling rate of the product by almost 40% and reduces the required length of the heat exchanger by approximately 35%.The results also illustrate that the most proper thickness of the porous media is approximately equal to 90% of the product tube's thickness.Results of this study lead to design a porous heat exchanger in CHFS system for various inlet conditions.展开更多
SPES/PVDF blends were employed to prepare the ion exchange membranes for vanadium redox flow battery(VRB) application for the first time. The addition of the highly crystalline and hydrophobic PVDF effectively limited...SPES/PVDF blends were employed to prepare the ion exchange membranes for vanadium redox flow battery(VRB) application for the first time. The addition of the highly crystalline and hydrophobic PVDF effectively limited the swelling behavior of SPES. The vanadium ion permeability of SPES/PVDF membranes was one order of magnitude lower than that of Nafion 117 membrane and pristine SPES membrane. Single cells with SPES/PVDF composite membranes showed significantly lower capacity loss, higher coulombic efficiency and higher energy efficiency than that with Nafion117 and pristine SPES membranes. The blend membrane with 40 wt% of PVDF(denoted as S_(0.6) P_(0.4)) showed energy efficiency of 83.2% at 30 mA?cm^(-2), which was superior to that of the Nafion117 and SPES membranes. In the self-discharge test, S_(0.6) P_(0.4) membrane showed twice longer duration in open circuit decay than that with Nafion 117 membrane. With all the good properties and low cost, the SPES/PVDF membranes are expected to have excellent commercial prospects as ion exchange membranes for VRB system.展开更多
This paper reports that an experimental study is conducted to examine the dynamics of the outflow in two-layer exchange flows in a channel connecting between two water bodies with a small density difference. The exper...This paper reports that an experimental study is conducted to examine the dynamics of the outflow in two-layer exchange flows in a channel connecting between two water bodies with a small density difference. The experiments reveal the generation of Kelvin-Helmholtz (KH) instabilities within the hydraulically sub-critical flow region of the channel. During maximal exchange, those KH instabilities develops into large-amplitude KH waves as they escape the channel exit into the reservoir. The propagation speed of those waves, their generation frequency and their amplitudes are studied. The dynamics of the outflow and these waves are directly linked to the hydraulic conditions of the exchange flow within the channel.展开更多
As the key equipment of floating liquefied natural gas(FLNG)process,the performance of spiral wound heat exchanger(SWHE)influences operation costs and reliability of the whole system.The sea conditions destroy the fal...As the key equipment of floating liquefied natural gas(FLNG)process,the performance of spiral wound heat exchanger(SWHE)influences operation costs and reliability of the whole system.The sea conditions destroy the falling film flow state of the refrigeration and then affect the heat transfer performance of FLNG SWHE.In order to design and optimize the SWHE,a cryogenic experimental device of FLNG process and a numerical model of falling film flow have been constructed to study the effects of sea conditions on the falling film flow and heat transfer characteristics of SWHE.The cryogenic experimental results show that the pitching conditions have larger effects on the heat transfer performance than yawing.Under the pitching angle of 7°,the natural gas temperature and gaseous refrigerant temperature increase by 3.22°C and 7.42°C,respectively.The flow rates of refrigerant and feed natural gas have a great impact on the heat transfer performance of SWHE under pitching and compound sloshing conditions.When the tilt angle increases to 9°,the tube structure with outer diameter D=8 mm and pipe spacing S=4 mm is recommended to reduce the drying area of the pipe wall surface.展开更多
Polybenzimidazole(PBI)is a kind of proton transport membrane material,and its ion conductivity is a key factor affecting its application in vanadium redox flow batteries(VRFBs).The casting solvent of PBI has a signifi...Polybenzimidazole(PBI)is a kind of proton transport membrane material,and its ion conductivity is a key factor affecting its application in vanadium redox flow batteries(VRFBs).The casting solvent of PBI has a significant influence on the acid doping level of PBI membranes which is closely related to ionic conductivity.In this paper,3,3′-diaminobenzidine(DABz)and 4,4′-Dicarboxydiphenylether(DCDPE)were used as raw materials by solution condensation to prepare the PBI with ether bond groups.The chemical structure of PBI was determined by1H NMR and FT-IR,and the prepared PBI had good solubility which can be dissolved in a variety of solvents.The PBI proton exchange membranes were prepared by solution coating with 5 different solvents of N,N-dimethylformamide(DMF),N,N-dimethylacetamide(DMAc),dimethyl sulfoxide(DMSO),1-methyl-2-pyrrolidone(NMP),methane sulfonic acid(MSA).The effects of different solvents on the ion conductivity and physicochemical properties were discussed in detail.The results showed that the PBI membrane prepared by using MSA as solvent(the PBI+MSA membrane)exhibits high water uptake,acid doping level and low vanadium ion permeability.The VRFB assembled with the PBI+MSA membrane exhibited higher coulombic efficiency(CE)99.87%and voltage efficiency(VE)84.50%than that of the commercial Nafion115 membrane at100 m A·cm-2,and after 480 cycles,the EE value can still be maintained at 83.73%.The self-discharge time of a single battery was recorded to be as long as 1000 h.All experimental data indicated that MSA is the best solvent for casting PBI membrane.展开更多
The present study focuses on the native readers’sense of flow,a construct frequently ignored in L2 writing studies.Based on the author’s analysis of the communicative data in the web-based transnational peer editing...The present study focuses on the native readers’sense of flow,a construct frequently ignored in L2 writing studies.Based on the author’s analysis of the communicative data in the web-based transnational peer editing activities named Cross-Pacific Exchange,an amendment is proposed for the currently well-accepted“input-output”models;that is,fluent output by classroom L2 learners may not always be accepted by native audience.Accordingly,L2 writing teachers should encourage their students to pay attention to their L1 readers’sense of flow,so as to enhance their own reader awareness,and improve the quality of their L2 composition through interaction with their L1 audience.展开更多
Due to the high heterogeneity and complexity of water flow movement for multiple karst water-bearing mediums,the evaluation,effective development,and utilization of karst water resources are significantly limited.Matr...Due to the high heterogeneity and complexity of water flow movement for multiple karst water-bearing mediums,the evaluation,effective development,and utilization of karst water resources are significantly limited.Matrix flow is usually laminar,whereas conduit flow is usually turbulent.The driving mechanisms of water exchange that occur between the karst conduit and its adjacent matrix are not well understood.This paper investigates the hydrodynamic characteristics and the mechanism of flow exchange in dual water-bearing mediums(conduit and matrix)of karst aquifers through laboratory experimentation and numerical simulation.A karst aquifer consisting of a matrix network and a conduit was proposed,and the relationship between the water exchange flux and hydraulic head differences generated from the laboratory experiments was analyzed.Two modes of experimental tests were performed with different fixed water level boundaries in the laboratory karst aquifer.The results indicate that the water exchange capacity was proportional to the square root of hydraulic head differences.The linear exchange term in the conduit flow process(CFP)source program was modified according to experimental results.The modified CFP and the original CFP model experimental data results were compared,and it was found that the modified CFP model had better fitting effects.These results showed that the water exchange mechanism between conduit and matrix is very important for solid-liquid interface reaction,water resource evaluation,and understanding of karst hydrodynamic behavior.展开更多
基金Thanks to Major Scientific and Technological Innovation Projects in Shandong Province(2018-CXGC0803)for the financial support of this article.
文摘Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present work a new spiral flow field with a bypass is proposed.The reaction gas enters the flow field in the central path and diffuses in two directions through the flow channel and the bypass.The bypasses are arranged incrementally.The number of bypasses and the cross-section size of the bypasses are varied parametrically while a single-cell model of the PEMFC is used.The influence of the concentration of liquid water and oxygen in the cell on the performance of different flow fields is determined by means of Computational fluid dynamics(COMSOL Multiphysics software).Results show that when the bypass number is 48 and its cross-sectional area is 0.5 mm^(2),the cell exhibits the best performances.
基金The authors are grateful to"Chemical Grid Project"of Beijing University of Chemical Technology for providingthe computer facilities.
文摘A subsurface flow wetland(SSFW)was simulated using a commercial computational fluid dynamic(CFD)code.The constructed media was simulated using porous media and the liquid resident time distribution(RTD)in the SSFW was obtained using the particle trajectory model.The effect of wetland configuration and operating conditions on the hydraulic performance of the SSFW were investigated.The results indicated that the hydraulic performance of the SSFW was predominantly affected by the wetland configuration.The hydraulic effciency of the SSFW with an inlet at the middle edge of the upper media was 0.584 and the best among the SSFWs with an inlet at the top,the middle,and the bottom edge of the upper media.The constructed media affected the hydraulic performance by the ratio(K)of the upper and lower media resistance.The selection of appropriate media resistance in the protection layer can improve the hydraulic effciency.When the viscous resistance coeffcient of the media in the protection layer changed from 2.315×105 to 1.200×108,the hydraulic effciency of the SSFW increased from 0.301 to 0.751.However,the effect of operating conditions on the hydraulic effciency of the SSFW was slight.
基金This work was supported by the Fundamental Research Funds for the National Natural Science Foundation of China(No.41571265,41971244)the Key Research and Development Project of Social Livelihood in Chongqing(cstc2018jscxmszdX0061)the Foundation of Graduate Research and Innovation in Chongqing under project CYB18089.
文摘Subsurface water flow velocity influences the hydrodynamic characteristics of soil seepage and the interaction between subsurface water flow and surface runoff during soil erosion and sediment transport.A visualized method and equipment was adopted in this study to observe the subsurface water flow.Quartz sand was used as the test material of subsurface water flow and fluorescent dye was used as the indicator for tracing subsurface water flow.Water was supplied at the same flow discharge to the three parts at the bottom of the test flume,and the subsurface water flow were determined with four slope gradients(4°,8°,10°,and 12°).The results showed that the seepage velocity gradually increased with increasing slope gradient.The pore water velocity at different depths of sand layer profile increased with increasing slope gradient,whereas the thickness of the flow front gradually decreased.For the same slope gradient,the pore water velocity in the lower layer was the largest,whereas the thickness of the flow front was the smallest.Comparative analysis of the relationship between seepage velocity and pore water velocity at different depths of sand layer profile showed that the maximum relative difference between the measured pore water velocity and the computational pore water velocity at different depths of sand profile in the experiment was 4.38%.Thus,the test method for measuring the subsurface water flow velocity of sand layer profile adopted in this study was effective and feasible.The development of this experiment and the exploration of research methods would lay a good test foundation for future studies on the variation law of subsurface water flow velocity and the determination of flow velocity in purple soils,thus contributing to the improvement of the hydrodynamic mechanism of purple soils.
基金Under the auspices of the Creative Group Foundation of the National Natural Science Foundation of China(50721006)the National Basic Research Program of China(2006CB403402-3)+1 种基金the National Water Resource and Environment Special Item(2008ZX07207-006-04)the Natural Science Foundation of Shanghai(10ZR1400300)
文摘As an important design factor for constructed wetlands,hydraulic retention time and its distribution will affect the treatment performance.Instantaneously injected sodium chloride tracers were used to obtain residence time distributions of the lab scale subsurface flow constructed wetland.Considering the presence of trailing and multiple peaks of the tracer breakthrough curve,the multi flow dispersion model(MFDM)was used to fit the experimental tracer breakthrough curves.According to the residual sum of squares and comparison between the experimental values and simulated values of the tracer concentration,MFDM could fit the residence time distribution(RTD)curve satisfactorily,the results of which also reflected the layered structure of wetland cells,thus to give reference for application of MFDM to the same kind of subsurface flow constructed wetlands.
文摘The paper reports the findings of a research work carried out to examine the performance and efficiency of a subsurface constructed wetland (SSFCW) for the treatment of domestic sewage in the University of Lagos (Unilag), Nigeria. The removal patterns and efficiencies of the physical, chemical and biological sewage pollutants parameters of domestic waste water generated within Unilag community by the SSFCW were studied. The wastewater was sampled and analysed along the SSFCW from influent (point1) to effluent (point 11). Total Dissolved Solids (TDS) reduced from 471 mg/l to 11.85 mg/l (97.48%), Turbidity reduced from 108.75 HTU to 0.05HTU (99.95%), Manganese reduced from 6.05 mg/l to 0.61 mg/ (89.92%), Nitrate reduced from 27.5 mg/l to 2.0 mg/l (92.73%), Sulphate reduced from 48.5 mg/l to 28 mg/l (42.27%), Iron reduced from 1.13 mg/l to 0.03 mg/l (97.35%), BOD reduced from 73.14 mg/l to 12.8 mg/l (82.5%), and E-coli reduced from 874 MPN/100 ml to 0.15 MPN/100 ml (99.98%). On the other hand, Dissolved Oxygen content increased along the SSFCW from 3.14 mg/l to 7.49 mg/l (138.54%) while the pH improved from slightly acid level of 6.49 to slightly above neutral level of 7.05 (9.3%). All the parameters at effluent point are within the Nigerian Federal Environmental Protection Agency (FEPA) acceptable standard. The study concludes that the SSFCW is a cheap, efficient and appropriate technology for the treatment of domestic sewage under tropical conditions.
基金financially supported by the National Natural Science Foundation of China(Nos.41571265 and 42177314)the Key Research and Development Project of Social Livelihood in Chongqing(cstc2018jscx-mszd X0061)the Foundation of Graduate Research and Innovation in Chongqing(CYS21114)。
文摘Subsurface water flow above the weakly permeable soil layer commonly occurs on purple soil slopes.However,it remains difficult to quantify the effect of subsurface water flow on the surface flow velocity.Laboratory experiments were performed to measure the rill flow velocity on purple soil slopes containing a subsurface water flow layer with the electrolyte tracer method considering 3 subsurface water flow depths(SWFDs:5,10,and 15 cm),3 flow rates(FRs:2,4,and 8 L min^(-1)),and 4 slope gradients(SGs:5°,10°,15°,and 20°).As a result,the pulse boundary model fit the electrolyte transport processes very well under the different SWFDs.The measured rill flow velocities were 0.202 to 0.610 m s^(-1) under the various SWFDs.Stepwise regression results indicated a positive dependence of the flow velocity on the FR and SG but a negative dependence on the SWFD.The SWFD had notable effects on the rill flow velocity.Decreasing the SWFD from 15 to 5 cm increased the flow velocity.Moreover,the flow velocities under the 10-and 15-cm SWFDs were 89%and 86%,respectively,of that under the 5-cm SWFD.The flow velocity under the 5-,10-and 15-cm SWFDs was decreased to 89%,80%,and 77%,respectively,of that on saturated soil slopes.The results will enhance the understanding of rill flow hydrological processes under SWFD impact.
文摘The operational performance of a full scale subsurface flow constructed wetland, which treated the mixed industrial and domestic wastewater with BOD 5/COD mean ratio of 0 33 at Shatian, Shenzhen City was studied. The constructed wetland system consists of screens, sump, pumping station, and primary settling basin, facultative pond, first stage wetland and secondary stage wetland. The designed treatment capacity is 5000 m 3/d, and the actual influent flow is in the range of <2000 to >10000 m 3/d. Under normal operational conditions, the final effluent quality well met the National Integrated Wastewater Discharge Standard（GB 8978\1996）, with the following parameters（mean values）: COD 33 90 mg/L, BOD 5 7.65 mg/L, TSS 7.92 mg/L, TN 9.11 mg/L and TP 0 56 mg/L. Seven species of plants were selected to grow in the wetland: Reed, Sweetcane flower Silvergrass, Great Bulrush, Powdery Thalia and Canna of three colours. The growing season is a whole year round. The seasonal discrepancy could be observed and the plants growing in the wetland are vulnerable to lower temperature in winter. The recycling of the effluent in the first stage of the wetland system is an effective measure to improve the performance of the wetland system. The insufficient DO value in the wetland system not only had significant effect on pollutants removal in the wetland, but also was unfavourable to plant growth. The recycling of effluent to the inlet of wetland system and artificial pond to increase DO value of influent to the wetland is key to operate the subsurface constructed wetland steadily and effectively.
基金by the Natural Science Foundation of China (Grant No. 40801101)
文摘Subsurface flow is a prominent runoff process in sloping lands of purple soil in the upper Yangtze River basin.However,it remains difficult to identify and quantify.In this study,in situ runoff experimental plots were used to measure soil moisture dynamics using an array of time domain reflectometry(TDR) together with overland flow and subsurface flow using isolated collecting troughs.Frequency of preferential flow during rainfall events and the controls of subsurface flow processes were investigated through combined analysis of soil properties,topography,rainfall intensity,initial wetness,and tillage.Results showed that subsurface flow was ubiquitous in purple soil profiles due to welldeveloped macropores,especially in surface soils while frequency of preferential flow occurrence was very low(only 2 cases in plot C) during all 22 rainfall events.Dry antecedent moisture conditions promoted the occurrence of preferential flow.However,consecutive real-time monitoring of soil moisture at different depths and various slope positions implied the possible occurrence of multiple subsurface lateral flows during intensive storms.Rainfall intensity,tillage operation,and soil properties were recognized as main controls of subsurface flow in the study area,which allows the optimization of management practices for alleviating adverse environmental effects of subsurface flow in the region.
基金Supported by the Doctoral Foundation of Xi'an Jiaotong University (No. DFXJTU2002-12) the Foundation for Excellent Doctoral Dissertation Author by Minister of Education, China (No. 199933).
文摘The flow maldistribution and the effect of different inlet configuration on the flow distribution in platefin heat exchangers were studied experimentally. It is found that the flow maldistribution is serious because of the defects of inlet configurations, while the inlet configuration and Reynolds number are the main factors affecting the flow distribution. The improved inlet configurations, which are the header with a two-stage distributing configuration and the guide vane with a fluid complementary cavity were proposed and tested in this paper. The experimental results show that the improved inlet configurations can effectively improve the performance of flow distribution in heat exchangers.
文摘In this paper the performance of a counter flow microchannel heat exchanger (CFMCHE) is numerically investigated with a nanofluid as a cooling medium. Two types of nanofluids are used Cu-water and Al2O3-water. From the results obtained it’s found that thermal performance of CFMCHE increased with using the nanofluids as cooling medium with no extra increase in pressure drop due to the ultra fine solid particles and low volume fraction concentrations. The na-nofluids (Cu-water and Al2O3-water) volume fractions were in the range 1% to 5%. It’s also found that nanoflu-id-cooled CFMCHE could absorb more heat than water-cooled CFMCHE when the flow rate was low. For high flow rates the heat transfer was dominated by the volume flow rate and nanoparticles did not contribute to the extra heat absorption. Also the performance of CFMCHE can be increased considerably by using nanofluids with higher thermal conductivities.
文摘Experiments in monitoring the removal of organic material and nitrogen and determining the amounts of mi- croorganism at different sites in the subsurface flow constructed wetland in Sihong county were performed. The results show that the removal of CODCr agrees with the kinetic equation of a first order reaction. The removal of pollutants varies with different seasons. The removal rates of CODCr, NH3-N, TN in the spring are 15%–23% higher than those in the autumn. The amount of ammonifier is larger than that of denitrifying bacteria and the amount of denitrifying bacte- ria is larger than that of nitrosomonas. The amount of bacteria around the plant roots is larger than that on the surface of the packing medium. No apparent change is observed for the amount of denitrifying bacteria and nitrosomonas between spring and autumn.
文摘Objective To investigate the flow distribution in plate fin heat exchangers and optimize the design of header configuration for plate fin heat exchangers. Methods A mathematical model of header was proposed. The effects of the header configuration on the flow distribution in plate fin heat exchangers were investigated by CFD. The second header configuration with a two stage distributing structure was brought forward to improve the performance of flow distribution. Results It is found that the flow maldistribution is very serious in the direction of header length for the conventional header used in industry. The numerical predictions indicate that the improved header configurations can effectively improve the performance of flow distribution in plate fin heat exchangers. Conclusion The numerical simulation confirms that CFD should be a suitable tool for predicting the flow distribution. The method has a wide variety of applications in the design of plate fin heat exchangers.
文摘The aim of this study is to use a new configuration of porous media in a heat exchanger in continuous hydrothermal flow synthesis(CHFS)system to enhance the heat transfer and minimize the required length of the heat exchanger.For this purpose,numerous numerical simulations are performed to investigate performance of the system with porous media.First,the numerical simulation for the heat exchanger in CHFS system is validated by experimental data.Then,porous media is added to the system and six different thicknesses for the porous media are examined to obtain the optimum thickness,based on the minimum required length of the heat exchanger.Finally,by changing the flow rate and inlet temperature of the product as well as the cooling water flow rate,the minimum required length of the heat exchanger with porous media for various inlet conditions is assessed.The investigations indicate that using porous media with the proper thickness in the heat exchanger increases the cooling rate of the product by almost 40% and reduces the required length of the heat exchanger by approximately 35%.The results also illustrate that the most proper thickness of the porous media is approximately equal to 90% of the product tube's thickness.Results of this study lead to design a porous heat exchanger in CHFS system for various inlet conditions.
基金Funded by the Foundation of Sichuan Agricultural University(Nos.03572898 and 90214176)
文摘SPES/PVDF blends were employed to prepare the ion exchange membranes for vanadium redox flow battery(VRB) application for the first time. The addition of the highly crystalline and hydrophobic PVDF effectively limited the swelling behavior of SPES. The vanadium ion permeability of SPES/PVDF membranes was one order of magnitude lower than that of Nafion 117 membrane and pristine SPES membrane. Single cells with SPES/PVDF composite membranes showed significantly lower capacity loss, higher coulombic efficiency and higher energy efficiency than that with Nafion117 and pristine SPES membranes. The blend membrane with 40 wt% of PVDF(denoted as S_(0.6) P_(0.4)) showed energy efficiency of 83.2% at 30 mA?cm^(-2), which was superior to that of the Nafion117 and SPES membranes. In the self-discharge test, S_(0.6) P_(0.4) membrane showed twice longer duration in open circuit decay than that with Nafion 117 membrane. With all the good properties and low cost, the SPES/PVDF membranes are expected to have excellent commercial prospects as ion exchange membranes for VRB system.
文摘This paper reports that an experimental study is conducted to examine the dynamics of the outflow in two-layer exchange flows in a channel connecting between two water bodies with a small density difference. The experiments reveal the generation of Kelvin-Helmholtz (KH) instabilities within the hydraulically sub-critical flow region of the channel. During maximal exchange, those KH instabilities develops into large-amplitude KH waves as they escape the channel exit into the reservoir. The propagation speed of those waves, their generation frequency and their amplitudes are studied. The dynamics of the outflow and these waves are directly linked to the hydraulic conditions of the exchange flow within the channel.
基金supported by the National Natural Science Foundation of China(U21B2085)the Natural Science Foundation of Shandong Province of China(ZR2021QE073)+2 种基金the China Postdoctoral Science Foundation(2021M703587)the Qingdao Postdoctoral Applied Research Project(qdyy20200096)Fundamental Research Funds for the Central Universities(20CX06076A)
文摘As the key equipment of floating liquefied natural gas(FLNG)process,the performance of spiral wound heat exchanger(SWHE)influences operation costs and reliability of the whole system.The sea conditions destroy the falling film flow state of the refrigeration and then affect the heat transfer performance of FLNG SWHE.In order to design and optimize the SWHE,a cryogenic experimental device of FLNG process and a numerical model of falling film flow have been constructed to study the effects of sea conditions on the falling film flow and heat transfer characteristics of SWHE.The cryogenic experimental results show that the pitching conditions have larger effects on the heat transfer performance than yawing.Under the pitching angle of 7°,the natural gas temperature and gaseous refrigerant temperature increase by 3.22°C and 7.42°C,respectively.The flow rates of refrigerant and feed natural gas have a great impact on the heat transfer performance of SWHE under pitching and compound sloshing conditions.When the tilt angle increases to 9°,the tube structure with outer diameter D=8 mm and pipe spacing S=4 mm is recommended to reduce the drying area of the pipe wall surface.
基金the National Natural Science Foundation of China(No.21878317)the Beijing National Science Foundation(L172047)for financial support。
文摘Polybenzimidazole(PBI)is a kind of proton transport membrane material,and its ion conductivity is a key factor affecting its application in vanadium redox flow batteries(VRFBs).The casting solvent of PBI has a significant influence on the acid doping level of PBI membranes which is closely related to ionic conductivity.In this paper,3,3′-diaminobenzidine(DABz)and 4,4′-Dicarboxydiphenylether(DCDPE)were used as raw materials by solution condensation to prepare the PBI with ether bond groups.The chemical structure of PBI was determined by1H NMR and FT-IR,and the prepared PBI had good solubility which can be dissolved in a variety of solvents.The PBI proton exchange membranes were prepared by solution coating with 5 different solvents of N,N-dimethylformamide(DMF),N,N-dimethylacetamide(DMAc),dimethyl sulfoxide(DMSO),1-methyl-2-pyrrolidone(NMP),methane sulfonic acid(MSA).The effects of different solvents on the ion conductivity and physicochemical properties were discussed in detail.The results showed that the PBI membrane prepared by using MSA as solvent(the PBI+MSA membrane)exhibits high water uptake,acid doping level and low vanadium ion permeability.The VRFB assembled with the PBI+MSA membrane exhibited higher coulombic efficiency(CE)99.87%and voltage efficiency(VE)84.50%than that of the commercial Nafion115 membrane at100 m A·cm-2,and after 480 cycles,the EE value can still be maintained at 83.73%.The self-discharge time of a single battery was recorded to be as long as 1000 h.All experimental data indicated that MSA is the best solvent for casting PBI membrane.
文摘The present study focuses on the native readers’sense of flow,a construct frequently ignored in L2 writing studies.Based on the author’s analysis of the communicative data in the web-based transnational peer editing activities named Cross-Pacific Exchange,an amendment is proposed for the currently well-accepted“input-output”models;that is,fluent output by classroom L2 learners may not always be accepted by native audience.Accordingly,L2 writing teachers should encourage their students to pay attention to their L1 readers’sense of flow,so as to enhance their own reader awareness,and improve the quality of their L2 composition through interaction with their L1 audience.
基金funded by the Guangxi Natural Science Foundation(2018JJA150153)China Geological Survey Research Fund(JYYWF20180402)the project of China Geological Survey(DD20190342)。
文摘Due to the high heterogeneity and complexity of water flow movement for multiple karst water-bearing mediums,the evaluation,effective development,and utilization of karst water resources are significantly limited.Matrix flow is usually laminar,whereas conduit flow is usually turbulent.The driving mechanisms of water exchange that occur between the karst conduit and its adjacent matrix are not well understood.This paper investigates the hydrodynamic characteristics and the mechanism of flow exchange in dual water-bearing mediums(conduit and matrix)of karst aquifers through laboratory experimentation and numerical simulation.A karst aquifer consisting of a matrix network and a conduit was proposed,and the relationship between the water exchange flux and hydraulic head differences generated from the laboratory experiments was analyzed.Two modes of experimental tests were performed with different fixed water level boundaries in the laboratory karst aquifer.The results indicate that the water exchange capacity was proportional to the square root of hydraulic head differences.The linear exchange term in the conduit flow process(CFP)source program was modified according to experimental results.The modified CFP and the original CFP model experimental data results were compared,and it was found that the modified CFP model had better fitting effects.These results showed that the water exchange mechanism between conduit and matrix is very important for solid-liquid interface reaction,water resource evaluation,and understanding of karst hydrodynamic behavior.
