This paper presents failure mechanisms of the soil at the caisson-tip with fillet during suction-assisted penetration of suction caissons in undrained clay.Theoretical solutions of resistance factor N_c of the caisson...This paper presents failure mechanisms of the soil at the caisson-tip with fillet during suction-assisted penetration of suction caissons in undrained clay.Theoretical solutions of resistance factor N_c of the caisson-tip are obtained in terms of the caisson-tip geometry ratio of the flat section of the caisson-tip to the caisson wall thickness m/t and adhesion factorsα_i along inside of caisson wall andα_b at the base of the caisson-tip.It is indicated that the factor N_c increases with the increase of m/t,α_i and a_b.The resistance factors N_c for the rough base(α_b=1)are larger by 0.57than that for the smooth base(α_b=0).Besides,the factors N_c of caisson-tip with flat base(m=t)are larger by 1.14 than that with full internal fillet(m=0).The required suction to penetrate suction caissons with various fillets is obtained in terms of the force equilibrium in vertical direction.The finite element limit analysis and centrifuge model test results are used to verify the rationality of the presented failure mechanisms and theoretical predictions.展开更多
Suction caissons are widely used for anchoring floating platform and offshore wind turbines.Penetration of the suction caisson into the desired position under the combination of its self-weight and applied suction res...Suction caissons are widely used for anchoring floating platform and offshore wind turbines.Penetration of the suction caisson into the desired position under the combination of its self-weight and applied suction resulted from pumping out the encased water is integral to practical engineering.Model tests were carried out to investigate the suctionassisted installation of suction caissons in clay under various undrained shear strengths.It was found that there exists a critical penetration depth value.When the penetration depth is smaller than the critical value,the soil plug undrained shear strength is higher than intact clay(i.e.,clay prior to installation).However,when the penetration depth is greater than the critical penetration depth,the undrained shear strength of soil plug is lower than intact clay.The critical value decreases with the increasing consolidation time and undrained shear strength of clay.During suction-assisted installation,cracks occur around suction caissons.The installation way has little effect on the crack formation.The influence range(i.e.,the maximum distance between the crack and the suction caisson edge)was found to increase with the increasing friction coefficient of interface between the suction caisson wall and soil and decreases with the increasing soil undrained shear strength.In addition,the drained condition of the clay during installation is dominated by the caisson aspect ratio,the undrained shear strength and the friction coefficient between the caisson wall and clay.Equations to estimate the penetration resistance and the required suction to install the suction caisson are summarized.展开更多
Introduction: Endotracheal suction plays a crucial role in the management of mechanically ventilated patients. This study aims to evaluate the clinical effectiveness and safety of suction tubes with markings in mechan...Introduction: Endotracheal suction plays a crucial role in the management of mechanically ventilated patients. This study aims to evaluate the clinical effectiveness and safety of suction tubes with markings in mechanically ventilated pediatric patients. Materials and Methods: A randomized assignment was carried out on a cohort of 52 pediatric patients who underwent mechanical ventilation in the Pediatric Intensive Care Unit at the Third Affiliated Hospital of Sun Yat-sen University, covering the period from January 2022 to December 2022. These patients were divided into two groups: an improved group (n = 26) utilizing marked suction tubes, and a regular group (n = 26) employing conventional suction tubes. The objective of our study was to evaluate the clinical effectiveness of marked suction tubes. Results: The effects of the improved group on the vital signs of children undergoing mechanical ventilation were small and statistically significant compared with the regular group (p < 0.05). Additionally, the improved group exhibited a reduced frequency of sputum suction, shorter mechanical ventilation duration, and fewer days of hospitalization in the PICU compared to the regular group during the ventilation period. Notably, the difference in the duration of PICU hospitalization was statistically significant (p < 0.05). Moreover, the incidence of adverse reactions in the improved group was notably lower, with statistically significant differences observed in airway mucous membrane damage and irritating cough when compared to the regular group (p < 0.05). Conclusion: The utilization of marked suction tubes provides clinical nurses with clear guidance for performing suctioning with ease, efficiency and safety. Consequently, advocating for the widespread implementation of marked suction tubes in clinical practice is a commendable pursuit.展开更多
Background: In spine surgery postoperative closed suction drainage is used to decrease the potential risks of wound hematoma formation, and reduces the risk of infection, cord compression and neurologic deficit. Howev...Background: In spine surgery postoperative closed suction drainage is used to decrease the potential risks of wound hematoma formation, and reduces the risk of infection, cord compression and neurologic deficit. However, the efficacy of drains used for this purpose in adolescent idiopathic scoliosis is controversial. The purpose of this study is to evaluate outcomes of patients after posterior spinal fusion with instrumentation for adolescent idiopathic scoliosis without wound suction drainage. Methods: A total of 66 Patients who underwent posterior spinal fusion and instrumentation for the correction of Adolescent idiopathic scoliosis without the use of drain from January 2012 to January 2021 were included. Wound dehiscence, wound hematoma, infection, preoperative and postoperative hemoglobin levels and need for transfusion were described as frequency and mean values. Results: The average age was 15.06 years. Hospital stay was 2.2 days. Patients were followed-up over 50.21 months. There was no deep infection, wound hematoma. The difference between just postoperative and three days after operation hemoglobin levels was not significant and no need for transfusion. Only 3 (4.5%) cases with superficial skin infection and 4 (6%) cases with skin and Wound dehiscence were treated with dressing and antibiotics with full recovery. Conclusion: Without using drain for patients with idiopathic scoliosis who underwent posterior spinal fusion and instrumentation, no increase in blood loss, transfusion requirements, wound infection, skin dehiscence, and wound hematoma was observed.展开更多
This study investigates the suction and magnetic field effects on the two-dimensional nanofluid flow through a stretching/shrinking sheet at the stagnation point in the porous medium with thermal radiation.The governi...This study investigates the suction and magnetic field effects on the two-dimensional nanofluid flow through a stretching/shrinking sheet at the stagnation point in the porous medium with thermal radiation.The governing partial differential equations(PDEs)are converted into ordinary differential equations(ODEs)using the similarity transformation.The resulting ODEs are then solved numerically by using the bvp4c solver in MATLAB software.It was found that dual solutions exist for the shrinking parameter values up to a certain range.The numerical results obtained are compared,and the comparison showed a good agreement with the existing results in the literature.The governing parameters’effect on the velocity,temperature and nanoparticle fraction fields as well as the skin friction coefficient,the local Nusselt number and the Sherwood number are represented graphically and analyzed.The variation of the velocity,temperature and concentration increase with the increase in the suction and magnetic field parameters.It seems that the thermal radiation effect has increased the local Sherwood number while the local Nusselt number is reduced with it.展开更多
The application of the wellhead suction anchor in the second production test of natural gas hydrates(NGHs)in the South China Sea(SCS)was met with success.This design incorporates a central conductor guide pipe,which d...The application of the wellhead suction anchor in the second production test of natural gas hydrates(NGHs)in the South China Sea(SCS)was met with success.This design incorporates a central conductor guide pipe,which distinguishes it from traditional suction foundations.However,this addition resulted in a relatively high penetration resistance and a shallower penetration depth at the self-weight penetration stage.To mitigate this issue,the current study proposes an optimized design where the end of the suction foundation is sharpened.The installation characteristics of the traditional suction foundation and new suction foundation during self-weight penetration into sand are studied through laboratory tests and theoretical analysis.The flat and sharpened bottom shapes are considered in the traditional and new suction models.The effects of the initial penetration velocity on the initial penetration depth and soil plug and impact cavity characteristics are systematically studied.The results show that the self-weight penetration depth of the foundation with a sharpened bottom is 44.5%deeper than that of the foundation with a flat bottom.There are cavities around the foundation at the self-weight penetration stage,and the penetration depth is overestimated by 15%-30%.Finally,a model for predicting the penetration depth of the new suction foundation is proposed.展开更多
The thickness of shallow landslides is generally less than 2 m,which is of the same order of magnitude as the growth range of vegetation roots.Vegetation roots can improve the stability of shallow soil through mechani...The thickness of shallow landslides is generally less than 2 m,which is of the same order of magnitude as the growth range of vegetation roots.Vegetation roots can improve the stability of shallow soil through mechanical and hydraulic effects.Therefore,the landslide process is closely related to the plant roots growing on the slope surface.Plant roots play a dominant role in the regulation of soil suction through solar radiation induced transpiration.However,little is known about the correlation between cumulative solar radiation and soil suction.Moreover,the specific effects of fine roots on the suction distribution are not clear in most previous studies.In this study,a vegetated soil of a drought-tolerant and water-tolerant shrub,namely Amorpha fruticose,was adopted.The suction and volumetric water content of bare and vegetated soils were monitored under natural conditions for 4 months.The results demonstrate that there is a nearly linear relationship between cumulative solar radiation and suction ranging from zero to 100 kPa.Regarding the modeling of the soil-plant-atmosphere interactions,this relationship could serve a significant role in calculating the root water uptake under given solar radiation conditions.In addition,higher suctions were observed at the lower layer of the vegetated soil than those at the middle layer,which is different from the results of vegetated soil from previous investigations.This is due to the fact that the root area index(RAI)of fine roots at the lower layer is twice that of the middle layer.Importantly,the higher concentration of fine roots at the lower layer of vegetated soil sample resembles the root distribution of shrub near the soil-bedrock interface on shallow bedrock landslides.The fine roots would increase soil suction through transpiration,and hence reduce the permeability and increase shear strength of landslides.Eventually,these new findings serve as a preliminary step on the evaluation of the stability of this common type of landslides.展开更多
A357-SiCp/A357 layered composites were prepared using a semi-solid vacuum stirring suction casting method.The microstructures,mechanical properties,and thermal conductivities of the composites fabricated under differe...A357-SiCp/A357 layered composites were prepared using a semi-solid vacuum stirring suction casting method.The microstructures,mechanical properties,and thermal conductivities of the composites fabricated under different suction casting processes were compared.Additionally,the microstructural evolution characteristics and performance enhancement mechanism of the A357-SiCp/A357 layered composites were discussed.The results demonstrate that suction casting at 610°C with a low solid phase ratio can significantly enhance the material density and reduce the agglomeration of SiCp.The A357-SiC_(p)/A357 interface is clear and straight with good bonding.With an increase in the suction casting temperature,the bending resistance and thermal conductivity of the A357-SiC_(p)/A357 layered composites exhibit a trend of significantly increase at first and then slowly decrease owing to casting defects,interface bonding,and SiCp distribution.Compared with SiCp/A357 composites,the bending strength,deflection,and thermal conductivity of the A357-SiCp/A357 layered composites increase from 257 MPa,1.07 mm,and 155.72 W·(m·K)^(-1) to 298 MPa,2.1 mm,and 169.86 W·(m·K)^(-1),respectively.This study provides a reference for improving the rheological casting of aluminum matrix layered composites.展开更多
Objective: To compare the clinical effects of uterine cavity observation and suction surgery system with ultrasound guided induced abortion in very early pregnancy induced abortion surgery. Method: Select 80 patients ...Objective: To compare the clinical effects of uterine cavity observation and suction surgery system with ultrasound guided induced abortion in very early pregnancy induced abortion surgery. Method: Select 80 patients who requested termination of pregnancy due to early pregnancy from August 2022 to April 2023, and analyze the data. 40 patients who underwent ultrasound-guided induced abortion to terminate pregnancy were included in the control group, and 40 patients who underwent uterine cavity observation surgery to terminate pregnancy were included in the observation group. Compare the surgical time, number of times the straw enters the uterine cavity, incidence of complications, and menstrual recovery time between the two groups. Results: There was no statistically significant difference in the surgical time between the observation group and the control group, but the number of times negative pressure straws entered the uterine cavity and the incidence of surgical complications in the observation group were significantly lower than those in the control group (P Conclusion: Applying the uterine cavity observation and suction surgical system to terminate pregnancy in very early pregnancy has the advantages of minimal damage to the uterus and low incidence of surgical complications, greatly protecting the patient’s fertility.展开更多
Suction caissons can readily penetrate into the seabed under the combination of the self-weight and suction resulted from the encased water being increasingly pumped out. During suction-assisted penetration, the equiv...Suction caissons can readily penetrate into the seabed under the combination of the self-weight and suction resulted from the encased water being increasingly pumped out. During suction-assisted penetration, the equivalent overburden at the skirt-tip level outside the caisson is generally higher than that inside because the vertical stress within the soil plug is reduced by the exerted suction. This may result in a uniform shear stress developing over the base of the skirt-tip as the soil below the skirt-tip tends to move into the caisson, which leads to an asymmetric failure wedge existing below the base of the skirt-tip. Besides, different adhesion factors along the inside(αi) and outside(αo) of the skirt wall will cause asymmetric plastic zones inside and outside the caisson. Accordingly, an asymmetric failure mechanism is therefore proposed to calculate the penetration resistance of the skirt-tip. The proposed failure mechanism is the first to consider the effect of different adhesion factors(αi) and(αo) on the failure mechanism at the skirt-tip, and involves the contribution from the weighted average of equivalent overburdens inside and outside caisson at the skirt-tip level. The required suction pressure can be obtained in terms of force equilibrium of the caisson in a vertical direction. Finally, the asymmetric failure mechanism at the skirt-tip is validated with the FE calculations. By comparing with the measured data, the predictions of the required suction pressure are found to be in good agreement with the experimental results.展开更多
In this study, an intelligent monitoring platform is established for continuous quantification of soil,vegetation, and atmosphere parameters (e.g. soil suction, rainfall, tree canopy, air temperature, and windspeed) t...In this study, an intelligent monitoring platform is established for continuous quantification of soil,vegetation, and atmosphere parameters (e.g. soil suction, rainfall, tree canopy, air temperature, and windspeed) to provide an efficient dataset for modeling suction response through machine learning. Twocharacteristic parameters representing suction response during wetting processes, i.e. response time andmean reduction rate of suction, are formulated through multi-gene genetic programming (MGGP) usingeight selected influential parameters including depth, initial soil suction, vegetation- and atmosphererelated parameters. An error standardebased performance evaluation indicated that MGGP has appreciable potential for model development when working with even fewer than 100 data. Global sensitivityanalysis revealed the importance of tree canopy and mean wind speed to estimation of response timeand indicated that initial soil suction and rainfall amount have an important effect on the estimatedsuction reduction rate during a wetting process. Uncertainty assessment indicated that the two MGGPmodels describing suction response after rainfall are reliable and robust under uncertain conditions. Indepth analysis of spatial variations in suction response validated the robustness of two obtained MGGPmodels in prediction of suction variation characteristics under natural conditions.展开更多
Root tensile strength is an important factor controlling the performance of bio-slope stabilization works. Due to evapotranspiration and climate factors, the root moisture content and its suction can vary seasonally i...Root tensile strength is an important factor controlling the performance of bio-slope stabilization works. Due to evapotranspiration and climate factors, the root moisture content and its suction can vary seasonally in practice and may not equal soil suction. The influences of suction and root moisture contents were investigated on Chrysopogon zizanioides(vetiver grass) root tensile strength. The root specimens were equilibrated with moist air in different suction conditions(0, 10, 20, and 50 kPa), prior to root tension tests. The root-water characteristic curve or relationship between root moisture and suction, was determined. The increase in suction resulted in decreased tensile strengths of the grass roots, particularly those with diameter of about 0.2 mm, which constituted 50.7% of all roots. For 1 mm roots, the tensile strength appeared to be unaffected by suction increase. The average root tensile strengths were used to estimate the root cohesion in slope stability analysis to find variation of safety factors of a bioengineered slope in different suction conditions. The analysis showed that the critical condition of slope with the lowest factor of safety would happen when the soil suction was zero and the root suction was high. Such condition may occur during a heavy rain period after a prolonged drought.展开更多
The modified suction caisson(MSC) adds a short-skirted structure around the regular suction caissons to increase the lateral bearing capacity and limit the deflection. The MSC is suitable for acting as the offshore wi...The modified suction caisson(MSC) adds a short-skirted structure around the regular suction caissons to increase the lateral bearing capacity and limit the deflection. The MSC is suitable for acting as the offshore wind turbine foundation subjected to larger lateral loads compared with the imposed vertical loads. Determination of the lateral bearing capacity is a key issue for the MSC design. The formula estimating the lateral bearing capacity of the MSC was proposed in terms of the limit equilibrium method and was verified by the test results. Parametric studies on the lateral bearing capacity were also carried out. It was found that the lateral bearing capacity of the MSC increases with the increasing length and radius of the external skirt, and the lateral bearing capacity increases linearly with the increasing coefficient of subgrade reaction. The maximum lateral bearing capacity of the MSC is attained when the ratio of the radii of the internal compartment to the external skirt equals 0.82 and the ratio of the lengths of the external skirt to the internal compartment equals 0.48, provided that the steel usage of the MSC is kept constant.展开更多
A modified suction caisson(MSC), which was reported by the authors of this paper previously, comprises an external short-skirted structure that is added to a regular suction caisson(RSC). It has been proved that MSCs ...A modified suction caisson(MSC), which was reported by the authors of this paper previously, comprises an external short-skirted structure that is added to a regular suction caisson(RSC). It has been proved that MSCs can improve the lateral bearing capacity and limit the deflection of the caisson compared with RSCs. A series of model tests were conducted to investigate responses of MSCs subject to uplift loading in saturated sand. The effects of external skirt dimensions on the uplift bearing capacity of MSCs were considered. In addition, the influences of the sealed top lid of the skirted structure on the uplift bearing capacity and the resulting passive suction of MSCs were also studied. It was found that the uplift bearing capacities of MSCs are 1.4-1.7 times that of RSCs. Moreover, test results in serviceable conditions show that the sealed external skirted structure of perspex-made suction caissons significantly contributed to the uplift bearing capacity as a result of passive suction.展开更多
The modified suction caisson(MSC) is a novel type of foundation for ocean engineering, consisting of a short external closed-top cylinder-shaped structure surrounding the upper part of the regular suction caisson(RSC)...The modified suction caisson(MSC) is a novel type of foundation for ocean engineering, consisting of a short external closed-top cylinder-shaped structure surrounding the upper part of the regular suction caisson(RSC). The MSC can provide larger lateral bearing capacity and limit the deflection compared with the RSC. Therefore, the MSC can be much more appropriate to use as an offshore wind turbine foundation. Model tests on the MSC in saturated sand subjected to monotonic lateral loading were carried out to investigate the effects of external structure sizes on the sand surface deformation and the earth pressure distribution along the embedded depth. Test results show that the deformation range of the sand surface increases with the increasing width and length of the external structure. The magnitude of sand upheaval around the MSC is smaller than that of the RSC and the sand upheaval value around the MSC in the loading direction decreases with the increasing external structure dimensions. The net earth pressure in the loading direction acting on the internal compartment of the MSC is smaller than that of the RSC at the same embedded depth. The maximum net earth pressure acting on the external structure outer wall in the loading direction is larger than that of the internal compartment, indicating that a considerable amount of the lateral load and moment is resisted by the external skirt structure.展开更多
A vorticity-velocity method was used to study the incompressible viscous fluid flow around a circular cylinder with surface suction or blowing. The resulted high order implicit difference equations were effeciently so...A vorticity-velocity method was used to study the incompressible viscous fluid flow around a circular cylinder with surface suction or blowing. The resulted high order implicit difference equations were effeciently solved by the modified incomplete LUdecomposition conjugate gradient scheme (MILU-CG). The effects of surface suction or blowing' s position and strength on the vortex structures in the cylinder wake, as well as on the drag and lift forces at Reynoldes number Re = 100 were investigated numerically. The results show that the suction on the shoulder of the cylinder or the blowing on the rear of the cylinder can effeciently suppress the asymmetry of the vortex wake in the transverse direction and greatly reduce the lift force; the suction on the shoulder of the cylinder, when its strength is properly chosen, can reduce the drag force significantly, too.展开更多
Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investi...Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investigated the influence on details of the flow fields,especially vortexes in compressors. CFD method is validated with experi?mental data firstly. Three single?slot and one double?slot endwall boundary layer suction schemes are designed and investigated. In addition to the investigation of aerodynamic performance of the cascades with and without suction,variations in corner open separation,passage vortex,and concentration shedding vortex,which are rarely seen for the flow controlled blades in published literatures,are analyzed. Then,flow models,which are the ultimate aim,of both baseline and aspirated cascades are established. Results show that single?slot endwall suction scheme adjacent to the suction surface can e ectively remove the corner open separation. With suction mass flow rate of 0.85%,the overall loss coe cient and endwall loss coe cient of the cascade are reduced by 25.2% and 48.6%,respectively. Besides,this scheme increases the static pressure rise coe cient of the cascade by 3.2% and the flow turning angle of up to 3.3° at 90% span. The concentration shedding vortex decreases,whereas the passage vortex increases. For single?slot suction schemes near the middle pitchwise of the passage,the concentration shedding vortex increases and the passage vortex is divided into two smaller passage vortexes,which converge into a single?passage vortex near the trailing edge section of the cascade. For the double?slot suction scheme,triple?passage vortexes are presented in the blade passage. Some new vortex structures are discovered,and the novel flow models of aspirated compressor cascade are proposed,which are important to improve the design of multi?stage aspirated compressors.展开更多
Modified suction caissons(MSCs)acting as offshore wind turbine foundations will generate the accumulated rotation under cyclic loading resulted from waves.The accumulated rotation and the range of soil deformation aro...Modified suction caissons(MSCs)acting as offshore wind turbine foundations will generate the accumulated rotation under cyclic loading resulted from waves.The accumulated rotation and the range of soil deformation around the MSC under long-term cyclic wave loading were studied using 3-D numerical simulations.The Morison equation was adopted to calculate the wave loadings.It was found that the MSC accumulated rotation increases linearly with the increase of the logarithm of cyclic number.The normalized expression was proposed to reflect the relationship between the accumulated rotation and cyclic number.The soil deformation range around the MSC increases when increasing the cyclic number and loading amplitude.It can also be concluded that the accumulated rotation increases rapidly with this change of excess pore pressure in the first 4000 cycles.The responses of the MSC to wave and wind loads were also investigated.Results show that the accumulated rotation of the MSC under both wave and wind loadings is larger than that under the wave loading only.展开更多
Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisso...Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion.In order to study the uplift bearing mechanism and failure mode of suction caisson foundation,a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode.Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity.The smaller the permeability coefficient is,the higher the residual negative pressure will be.And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson.When the load reaches the ultimate bearing capacity,both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay.Combined the uplift bearing characteristics of caisson in sandy soil and soft clay,the bearing capacity composition and the calculation method are proposed.It can provide a reference for the engineering design of suction caisson foundation under vertical load.展开更多
A suction caisson can be extracted by applying reverse pumping water,which cannot be regarded as the reverse process of installation because of the dramatically different soil−structure interaction behavior.Model test...A suction caisson can be extracted by applying reverse pumping water,which cannot be regarded as the reverse process of installation because of the dramatically different soil−structure interaction behavior.Model tests were first carried out in this study to investigate the extraction behavior of the modified suction caisson(MSC)and the regular suction caisson(RSC)in sand by reverse pumping water.The effects of the installation ways(suction-assisted or jacking installation)and the reverse pumping rate on the variations of the over-pressure resulting form reverse pumping water were investigated.It was found that neither the RSC nor the MSC can be fully extracted from sand.When the maximum extraction displacement is obtained,the hydraulic gradient of the sand in the suction caisson reaches the critical value,leading to seepage failure.In addition,the maximum extraction displacement decreases with the increasing reverse pumping rate.Under the same reverse pumping rate,the final extraction displacements for the RSC and MSC installed by suction are lower than those for the RSC and MSC installed by jacking.The final extraction displacement of MSC is almost equal to that of the RSC with the same internal compartment length.Based on the force equilibrium,a method of estimating the maximum extraction displacement is proposed.It has been proved that the proposed method can rationally predict the maximum extraction displacement and the corresponding over-pressure.展开更多
基金financially supported by the National Natural Science Foundation of China (Grant No.51879044)the Youth Foundation of Shandong Natural Science Foundation (Grant No.ZR2020QE258)+1 种基金Qingdao Postdoctoral Applied Research Project (Grant No.ZX20220202)SDUST Research Fund (Grant No.2015KYJH104)。
文摘This paper presents failure mechanisms of the soil at the caisson-tip with fillet during suction-assisted penetration of suction caissons in undrained clay.Theoretical solutions of resistance factor N_c of the caisson-tip are obtained in terms of the caisson-tip geometry ratio of the flat section of the caisson-tip to the caisson wall thickness m/t and adhesion factorsα_i along inside of caisson wall andα_b at the base of the caisson-tip.It is indicated that the factor N_c increases with the increase of m/t,α_i and a_b.The resistance factors N_c for the rough base(α_b=1)are larger by 0.57than that for the smooth base(α_b=0).Besides,the factors N_c of caisson-tip with flat base(m=t)are larger by 1.14 than that with full internal fillet(m=0).The required suction to penetrate suction caissons with various fillets is obtained in terms of the force equilibrium in vertical direction.The finite element limit analysis and centrifuge model test results are used to verify the rationality of the presented failure mechanisms and theoretical predictions.
基金financially supported by the National Natural Science Foundation of China (Grant Nos.52371301,51879044 and 51808325)the Shandong Natural Fund (Grant No.ZR2020QE258)。
文摘Suction caissons are widely used for anchoring floating platform and offshore wind turbines.Penetration of the suction caisson into the desired position under the combination of its self-weight and applied suction resulted from pumping out the encased water is integral to practical engineering.Model tests were carried out to investigate the suctionassisted installation of suction caissons in clay under various undrained shear strengths.It was found that there exists a critical penetration depth value.When the penetration depth is smaller than the critical value,the soil plug undrained shear strength is higher than intact clay(i.e.,clay prior to installation).However,when the penetration depth is greater than the critical penetration depth,the undrained shear strength of soil plug is lower than intact clay.The critical value decreases with the increasing consolidation time and undrained shear strength of clay.During suction-assisted installation,cracks occur around suction caissons.The installation way has little effect on the crack formation.The influence range(i.e.,the maximum distance between the crack and the suction caisson edge)was found to increase with the increasing friction coefficient of interface between the suction caisson wall and soil and decreases with the increasing soil undrained shear strength.In addition,the drained condition of the clay during installation is dominated by the caisson aspect ratio,the undrained shear strength and the friction coefficient between the caisson wall and clay.Equations to estimate the penetration resistance and the required suction to install the suction caisson are summarized.
文摘Introduction: Endotracheal suction plays a crucial role in the management of mechanically ventilated patients. This study aims to evaluate the clinical effectiveness and safety of suction tubes with markings in mechanically ventilated pediatric patients. Materials and Methods: A randomized assignment was carried out on a cohort of 52 pediatric patients who underwent mechanical ventilation in the Pediatric Intensive Care Unit at the Third Affiliated Hospital of Sun Yat-sen University, covering the period from January 2022 to December 2022. These patients were divided into two groups: an improved group (n = 26) utilizing marked suction tubes, and a regular group (n = 26) employing conventional suction tubes. The objective of our study was to evaluate the clinical effectiveness of marked suction tubes. Results: The effects of the improved group on the vital signs of children undergoing mechanical ventilation were small and statistically significant compared with the regular group (p < 0.05). Additionally, the improved group exhibited a reduced frequency of sputum suction, shorter mechanical ventilation duration, and fewer days of hospitalization in the PICU compared to the regular group during the ventilation period. Notably, the difference in the duration of PICU hospitalization was statistically significant (p < 0.05). Moreover, the incidence of adverse reactions in the improved group was notably lower, with statistically significant differences observed in airway mucous membrane damage and irritating cough when compared to the regular group (p < 0.05). Conclusion: The utilization of marked suction tubes provides clinical nurses with clear guidance for performing suctioning with ease, efficiency and safety. Consequently, advocating for the widespread implementation of marked suction tubes in clinical practice is a commendable pursuit.
文摘Background: In spine surgery postoperative closed suction drainage is used to decrease the potential risks of wound hematoma formation, and reduces the risk of infection, cord compression and neurologic deficit. However, the efficacy of drains used for this purpose in adolescent idiopathic scoliosis is controversial. The purpose of this study is to evaluate outcomes of patients after posterior spinal fusion with instrumentation for adolescent idiopathic scoliosis without wound suction drainage. Methods: A total of 66 Patients who underwent posterior spinal fusion and instrumentation for the correction of Adolescent idiopathic scoliosis without the use of drain from January 2012 to January 2021 were included. Wound dehiscence, wound hematoma, infection, preoperative and postoperative hemoglobin levels and need for transfusion were described as frequency and mean values. Results: The average age was 15.06 years. Hospital stay was 2.2 days. Patients were followed-up over 50.21 months. There was no deep infection, wound hematoma. The difference between just postoperative and three days after operation hemoglobin levels was not significant and no need for transfusion. Only 3 (4.5%) cases with superficial skin infection and 4 (6%) cases with skin and Wound dehiscence were treated with dressing and antibiotics with full recovery. Conclusion: Without using drain for patients with idiopathic scoliosis who underwent posterior spinal fusion and instrumentation, no increase in blood loss, transfusion requirements, wound infection, skin dehiscence, and wound hematoma was observed.
基金the Fundamental Research Grant Scheme(FRGS)under a grant number of FRGS/1/2018/STG06/UNIMAP/02/3 from the Ministry of Education Malaysia。
文摘This study investigates the suction and magnetic field effects on the two-dimensional nanofluid flow through a stretching/shrinking sheet at the stagnation point in the porous medium with thermal radiation.The governing partial differential equations(PDEs)are converted into ordinary differential equations(ODEs)using the similarity transformation.The resulting ODEs are then solved numerically by using the bvp4c solver in MATLAB software.It was found that dual solutions exist for the shrinking parameter values up to a certain range.The numerical results obtained are compared,and the comparison showed a good agreement with the existing results in the literature.The governing parameters’effect on the velocity,temperature and nanoparticle fraction fields as well as the skin friction coefficient,the local Nusselt number and the Sherwood number are represented graphically and analyzed.The variation of the velocity,temperature and concentration increase with the increase in the suction and magnetic field parameters.It seems that the thermal radiation effect has increased the local Sherwood number while the local Nusselt number is reduced with it.
基金financially supported by the Key-Area Research and Development Program of Guangdong ProvinceChina(Grant No.2022B0101100001)+3 种基金the Marine Economic Development Special Program of Guangdong province(Six Major Marine Industries):Research and Demonstration of Critical Technologies for Comprehensive Prevention and Control of Natural Disaster in Offshore Wind FarmsChina(Grant No.29[2023])the Guangxi Key Laboratory of Disaster Prevention and Mitigation and Engineering SafetyChina(Grant No.2020ZDK002)。
文摘The application of the wellhead suction anchor in the second production test of natural gas hydrates(NGHs)in the South China Sea(SCS)was met with success.This design incorporates a central conductor guide pipe,which distinguishes it from traditional suction foundations.However,this addition resulted in a relatively high penetration resistance and a shallower penetration depth at the self-weight penetration stage.To mitigate this issue,the current study proposes an optimized design where the end of the suction foundation is sharpened.The installation characteristics of the traditional suction foundation and new suction foundation during self-weight penetration into sand are studied through laboratory tests and theoretical analysis.The flat and sharpened bottom shapes are considered in the traditional and new suction models.The effects of the initial penetration velocity on the initial penetration depth and soil plug and impact cavity characteristics are systematically studied.The results show that the self-weight penetration depth of the foundation with a sharpened bottom is 44.5%deeper than that of the foundation with a flat bottom.There are cavities around the foundation at the self-weight penetration stage,and the penetration depth is overestimated by 15%-30%.Finally,a model for predicting the penetration depth of the new suction foundation is proposed.
基金the financial supports from the National Natural Science Foundation of China(grant No.41925030 and 4179043)the Second Tibetan Plateau Scientific Expedition and Research Program(STEP,grant No.2019QZKK0904)the Natural Science Foundation of Shaanxi Province(2020JQ-041)。
文摘The thickness of shallow landslides is generally less than 2 m,which is of the same order of magnitude as the growth range of vegetation roots.Vegetation roots can improve the stability of shallow soil through mechanical and hydraulic effects.Therefore,the landslide process is closely related to the plant roots growing on the slope surface.Plant roots play a dominant role in the regulation of soil suction through solar radiation induced transpiration.However,little is known about the correlation between cumulative solar radiation and soil suction.Moreover,the specific effects of fine roots on the suction distribution are not clear in most previous studies.In this study,a vegetated soil of a drought-tolerant and water-tolerant shrub,namely Amorpha fruticose,was adopted.The suction and volumetric water content of bare and vegetated soils were monitored under natural conditions for 4 months.The results demonstrate that there is a nearly linear relationship between cumulative solar radiation and suction ranging from zero to 100 kPa.Regarding the modeling of the soil-plant-atmosphere interactions,this relationship could serve a significant role in calculating the root water uptake under given solar radiation conditions.In addition,higher suctions were observed at the lower layer of the vegetated soil than those at the middle layer,which is different from the results of vegetated soil from previous investigations.This is due to the fact that the root area index(RAI)of fine roots at the lower layer is twice that of the middle layer.Importantly,the higher concentration of fine roots at the lower layer of vegetated soil sample resembles the root distribution of shrub near the soil-bedrock interface on shallow bedrock landslides.The fine roots would increase soil suction through transpiration,and hence reduce the permeability and increase shear strength of landslides.Eventually,these new findings serve as a preliminary step on the evaluation of the stability of this common type of landslides.
文摘A357-SiCp/A357 layered composites were prepared using a semi-solid vacuum stirring suction casting method.The microstructures,mechanical properties,and thermal conductivities of the composites fabricated under different suction casting processes were compared.Additionally,the microstructural evolution characteristics and performance enhancement mechanism of the A357-SiCp/A357 layered composites were discussed.The results demonstrate that suction casting at 610°C with a low solid phase ratio can significantly enhance the material density and reduce the agglomeration of SiCp.The A357-SiC_(p)/A357 interface is clear and straight with good bonding.With an increase in the suction casting temperature,the bending resistance and thermal conductivity of the A357-SiC_(p)/A357 layered composites exhibit a trend of significantly increase at first and then slowly decrease owing to casting defects,interface bonding,and SiCp distribution.Compared with SiCp/A357 composites,the bending strength,deflection,and thermal conductivity of the A357-SiCp/A357 layered composites increase from 257 MPa,1.07 mm,and 155.72 W·(m·K)^(-1) to 298 MPa,2.1 mm,and 169.86 W·(m·K)^(-1),respectively.This study provides a reference for improving the rheological casting of aluminum matrix layered composites.
文摘Objective: To compare the clinical effects of uterine cavity observation and suction surgery system with ultrasound guided induced abortion in very early pregnancy induced abortion surgery. Method: Select 80 patients who requested termination of pregnancy due to early pregnancy from August 2022 to April 2023, and analyze the data. 40 patients who underwent ultrasound-guided induced abortion to terminate pregnancy were included in the control group, and 40 patients who underwent uterine cavity observation surgery to terminate pregnancy were included in the observation group. Compare the surgical time, number of times the straw enters the uterine cavity, incidence of complications, and menstrual recovery time between the two groups. Results: There was no statistically significant difference in the surgical time between the observation group and the control group, but the number of times negative pressure straws entered the uterine cavity and the incidence of surgical complications in the observation group were significantly lower than those in the control group (P Conclusion: Applying the uterine cavity observation and suction surgical system to terminate pregnancy in very early pregnancy has the advantages of minimal damage to the uterus and low incidence of surgical complications, greatly protecting the patient’s fertility.
基金financially supported by the National Natural Science Foundation of China (Grant Nos. 51639002 and 51879044)the SDUST Research Fund (Grant No. 2015KYJH104)。
文摘Suction caissons can readily penetrate into the seabed under the combination of the self-weight and suction resulted from the encased water being increasingly pumped out. During suction-assisted penetration, the equivalent overburden at the skirt-tip level outside the caisson is generally higher than that inside because the vertical stress within the soil plug is reduced by the exerted suction. This may result in a uniform shear stress developing over the base of the skirt-tip as the soil below the skirt-tip tends to move into the caisson, which leads to an asymmetric failure wedge existing below the base of the skirt-tip. Besides, different adhesion factors along the inside(αi) and outside(αo) of the skirt wall will cause asymmetric plastic zones inside and outside the caisson. Accordingly, an asymmetric failure mechanism is therefore proposed to calculate the penetration resistance of the skirt-tip. The proposed failure mechanism is the first to consider the effect of different adhesion factors(αi) and(αo) on the failure mechanism at the skirt-tip, and involves the contribution from the weighted average of equivalent overburdens inside and outside caisson at the skirt-tip level. The required suction pressure can be obtained in terms of force equilibrium of the caisson in a vertical direction. Finally, the asymmetric failure mechanism at the skirt-tip is validated with the FE calculations. By comparing with the measured data, the predictions of the required suction pressure are found to be in good agreement with the experimental results.
基金the financial support funded by the Science and Technology Development Fund of Macao SAR (Grant Nos. 0026/2020/AFJ and SKL-IOTSC(UM)-2021-2023)the Funds for University of Macao (Grant No. MYRG2018-00173-FST)
文摘In this study, an intelligent monitoring platform is established for continuous quantification of soil,vegetation, and atmosphere parameters (e.g. soil suction, rainfall, tree canopy, air temperature, and windspeed) to provide an efficient dataset for modeling suction response through machine learning. Twocharacteristic parameters representing suction response during wetting processes, i.e. response time andmean reduction rate of suction, are formulated through multi-gene genetic programming (MGGP) usingeight selected influential parameters including depth, initial soil suction, vegetation- and atmosphererelated parameters. An error standardebased performance evaluation indicated that MGGP has appreciable potential for model development when working with even fewer than 100 data. Global sensitivityanalysis revealed the importance of tree canopy and mean wind speed to estimation of response timeand indicated that initial soil suction and rainfall amount have an important effect on the estimatedsuction reduction rate during a wetting process. Uncertainty assessment indicated that the two MGGPmodels describing suction response after rainfall are reliable and robust under uncertain conditions. Indepth analysis of spatial variations in suction response validated the robustness of two obtained MGGPmodels in prediction of suction variation characteristics under natural conditions.
基金the financial supports from the Chaipattana FoundationKasetsart University Research and Development Institute(KURDI)the scholarship for his PhD studies provided by the Faculty of Engineering,Kasetsart University
文摘Root tensile strength is an important factor controlling the performance of bio-slope stabilization works. Due to evapotranspiration and climate factors, the root moisture content and its suction can vary seasonally in practice and may not equal soil suction. The influences of suction and root moisture contents were investigated on Chrysopogon zizanioides(vetiver grass) root tensile strength. The root specimens were equilibrated with moist air in different suction conditions(0, 10, 20, and 50 kPa), prior to root tension tests. The root-water characteristic curve or relationship between root moisture and suction, was determined. The increase in suction resulted in decreased tensile strengths of the grass roots, particularly those with diameter of about 0.2 mm, which constituted 50.7% of all roots. For 1 mm roots, the tensile strength appeared to be unaffected by suction increase. The average root tensile strengths were used to estimate the root cohesion in slope stability analysis to find variation of safety factors of a bioengineered slope in different suction conditions. The analysis showed that the critical condition of slope with the lowest factor of safety would happen when the soil suction was zero and the root suction was high. Such condition may occur during a heavy rain period after a prolonged drought.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51639002 and 51379118)Shandong University of Science and Technology Scientific Found(Grant No.2015TDJH104)
文摘The modified suction caisson(MSC) adds a short-skirted structure around the regular suction caissons to increase the lateral bearing capacity and limit the deflection. The MSC is suitable for acting as the offshore wind turbine foundation subjected to larger lateral loads compared with the imposed vertical loads. Determination of the lateral bearing capacity is a key issue for the MSC design. The formula estimating the lateral bearing capacity of the MSC was proposed in terms of the limit equilibrium method and was verified by the test results. Parametric studies on the lateral bearing capacity were also carried out. It was found that the lateral bearing capacity of the MSC increases with the increasing length and radius of the external skirt, and the lateral bearing capacity increases linearly with the increasing coefficient of subgrade reaction. The maximum lateral bearing capacity of the MSC is attained when the ratio of the radii of the internal compartment to the external skirt equals 0.82 and the ratio of the lengths of the external skirt to the internal compartment equals 0.48, provided that the steel usage of the MSC is kept constant.
基金supported by the National Natural Science Foundation of China(nos.51379118 and 51639002)SDUST Research Fund(no.2015TDJH104)
文摘A modified suction caisson(MSC), which was reported by the authors of this paper previously, comprises an external short-skirted structure that is added to a regular suction caisson(RSC). It has been proved that MSCs can improve the lateral bearing capacity and limit the deflection of the caisson compared with RSCs. A series of model tests were conducted to investigate responses of MSCs subject to uplift loading in saturated sand. The effects of external skirt dimensions on the uplift bearing capacity of MSCs were considered. In addition, the influences of the sealed top lid of the skirted structure on the uplift bearing capacity and the resulting passive suction of MSCs were also studied. It was found that the uplift bearing capacities of MSCs are 1.4-1.7 times that of RSCs. Moreover, test results in serviceable conditions show that the sealed external skirted structure of perspex-made suction caissons significantly contributed to the uplift bearing capacity as a result of passive suction.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51639002 and 51379118)the SDUST Research Fund(Grant No.2015KYTD104)
文摘The modified suction caisson(MSC) is a novel type of foundation for ocean engineering, consisting of a short external closed-top cylinder-shaped structure surrounding the upper part of the regular suction caisson(RSC). The MSC can provide larger lateral bearing capacity and limit the deflection compared with the RSC. Therefore, the MSC can be much more appropriate to use as an offshore wind turbine foundation. Model tests on the MSC in saturated sand subjected to monotonic lateral loading were carried out to investigate the effects of external structure sizes on the sand surface deformation and the earth pressure distribution along the embedded depth. Test results show that the deformation range of the sand surface increases with the increasing width and length of the external structure. The magnitude of sand upheaval around the MSC is smaller than that of the RSC and the sand upheaval value around the MSC in the loading direction decreases with the increasing external structure dimensions. The net earth pressure in the loading direction acting on the internal compartment of the MSC is smaller than that of the RSC at the same embedded depth. The maximum net earth pressure acting on the external structure outer wall in the loading direction is larger than that of the internal compartment, indicating that a considerable amount of the lateral load and moment is resisted by the external skirt structure.
基金Foundation item:the Natural Science Foundation of Jiangsu Province(BK97056109)
文摘A vorticity-velocity method was used to study the incompressible viscous fluid flow around a circular cylinder with surface suction or blowing. The resulted high order implicit difference equations were effeciently solved by the modified incomplete LUdecomposition conjugate gradient scheme (MILU-CG). The effects of surface suction or blowing' s position and strength on the vortex structures in the cylinder wake, as well as on the drag and lift forces at Reynoldes number Re = 100 were investigated numerically. The results show that the suction on the shoulder of the cylinder or the blowing on the rear of the cylinder can effeciently suppress the asymmetry of the vortex wake in the transverse direction and greatly reduce the lift force; the suction on the shoulder of the cylinder, when its strength is properly chosen, can reduce the drag force significantly, too.
基金Supported by China Postdoctoral Science Foundation(Grant No.2016M600015)National Natural Science Foundation of China(Grant Nos.51741601,51236006)
文摘Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investigated the influence on details of the flow fields,especially vortexes in compressors. CFD method is validated with experi?mental data firstly. Three single?slot and one double?slot endwall boundary layer suction schemes are designed and investigated. In addition to the investigation of aerodynamic performance of the cascades with and without suction,variations in corner open separation,passage vortex,and concentration shedding vortex,which are rarely seen for the flow controlled blades in published literatures,are analyzed. Then,flow models,which are the ultimate aim,of both baseline and aspirated cascades are established. Results show that single?slot endwall suction scheme adjacent to the suction surface can e ectively remove the corner open separation. With suction mass flow rate of 0.85%,the overall loss coe cient and endwall loss coe cient of the cascade are reduced by 25.2% and 48.6%,respectively. Besides,this scheme increases the static pressure rise coe cient of the cascade by 3.2% and the flow turning angle of up to 3.3° at 90% span. The concentration shedding vortex decreases,whereas the passage vortex increases. For single?slot suction schemes near the middle pitchwise of the passage,the concentration shedding vortex increases and the passage vortex is divided into two smaller passage vortexes,which converge into a single?passage vortex near the trailing edge section of the cascade. For the double?slot suction scheme,triple?passage vortexes are presented in the blade passage. Some new vortex structures are discovered,and the novel flow models of aspirated compressor cascade are proposed,which are important to improve the design of multi?stage aspirated compressors.
基金the National Natural Science Foundation of China(Grant Nos.51639002,51879044 and 51808325)SDUST(Shandong University of Science and Technology)Research Fund(Grant No.2015KYTD104).
文摘Modified suction caissons(MSCs)acting as offshore wind turbine foundations will generate the accumulated rotation under cyclic loading resulted from waves.The accumulated rotation and the range of soil deformation around the MSC under long-term cyclic wave loading were studied using 3-D numerical simulations.The Morison equation was adopted to calculate the wave loadings.It was found that the MSC accumulated rotation increases linearly with the increase of the logarithm of cyclic number.The normalized expression was proposed to reflect the relationship between the accumulated rotation and cyclic number.The soil deformation range around the MSC increases when increasing the cyclic number and loading amplitude.It can also be concluded that the accumulated rotation increases rapidly with this change of excess pore pressure in the first 4000 cycles.The responses of the MSC to wave and wind loads were also investigated.Results show that the accumulated rotation of the MSC under both wave and wind loadings is larger than that under the wave loading only.
基金the National Key Research and Development Program(Grant No.2017YFC0703408)the National Natural Science Foundation of China(Grant Nos.51678145 and 51478160)the Natural Science Foundation of Jiangsu Province(Grant No.BK20180155).
文摘Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion.In order to study the uplift bearing mechanism and failure mode of suction caisson foundation,a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode.Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity.The smaller the permeability coefficient is,the higher the residual negative pressure will be.And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson.When the load reaches the ultimate bearing capacity,both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay.Combined the uplift bearing characteristics of caisson in sandy soil and soft clay,the bearing capacity composition and the calculation method are proposed.It can provide a reference for the engineering design of suction caisson foundation under vertical load.
基金This study was financially supported by the National Natural Science Foundation of China(Grant Nos.51879044 and 51639002)the Shandong Natural Fund(Grant No.ZR2019BEE007)+1 种基金SDUST Research Fund(Grant No.2015TDJH104)the Project oce and Technology Program(Grant No.J18KA184).
文摘A suction caisson can be extracted by applying reverse pumping water,which cannot be regarded as the reverse process of installation because of the dramatically different soil−structure interaction behavior.Model tests were first carried out in this study to investigate the extraction behavior of the modified suction caisson(MSC)and the regular suction caisson(RSC)in sand by reverse pumping water.The effects of the installation ways(suction-assisted or jacking installation)and the reverse pumping rate on the variations of the over-pressure resulting form reverse pumping water were investigated.It was found that neither the RSC nor the MSC can be fully extracted from sand.When the maximum extraction displacement is obtained,the hydraulic gradient of the sand in the suction caisson reaches the critical value,leading to seepage failure.In addition,the maximum extraction displacement decreases with the increasing reverse pumping rate.Under the same reverse pumping rate,the final extraction displacements for the RSC and MSC installed by suction are lower than those for the RSC and MSC installed by jacking.The final extraction displacement of MSC is almost equal to that of the RSC with the same internal compartment length.Based on the force equilibrium,a method of estimating the maximum extraction displacement is proposed.It has been proved that the proposed method can rationally predict the maximum extraction displacement and the corresponding over-pressure.
