Profile shift is a highly effective technique for optimizing the performance of spur gear transmission systems.However,tooth surface wear is inevitable during gear meshing due to inadequate lubrication and long-term o...Profile shift is a highly effective technique for optimizing the performance of spur gear transmission systems.However,tooth surface wear is inevitable during gear meshing due to inadequate lubrication and long-term operation.Both profile shift and tooth surface wear(TSW)can impact the meshing characteristics by altering the involute tooth profile.In this study,a tooth stiffness model of spur gears that incorporates profile shift,TSW,tooth deformation,tooth contact deformation,fillet-foundation deformation,and gear body structure coupling is established.This model efficiently and accurately determines the time-varying mesh stiffness(TVMS).Additionally,an improved wear depth prediction method for spur gears is developed,which takes into consideration the mutually prime teeth numbers and more accurately reflects actual gear meshing conditions.Results show that consideration of the mutual prime of teeth numbers will have a certain impact on the TSW process.Furthermore,the finite element method(FEM)is employed to accurately verify the values of TVMS and load sharing ratio(LSR)of profile-shifted gears and worn gears.This study quantitatively analyzes the effect of profile shift on the surface wear process,which suggests that gear profile shift can partially alleviate the negative effects of TSW.The contribution of this study provides valuable insights into the design and maintenance of spur gear systems.展开更多
Microwave reflectometry is a powerful diagnostic that can measure the density profile and localized turbulence with high spatial and temporal resolution and will be used in ITER,so understanding the influence of plasm...Microwave reflectometry is a powerful diagnostic that can measure the density profile and localized turbulence with high spatial and temporal resolution and will be used in ITER,so understanding the influence of plasma perturbations on the reflect signal is important.The characteristics of the reflect signal from profile reflectometry,the time-of-flight(TOF)signal associated with the MHD instabilities,are investigated in EAST.Using a 1D full-wave simulation code by the Finite-DifferenceTime-Domain(FDTD)method,it is well validated that the local density flattening could induce the discontinuity of the simulated TOF signal and an obvious change of reflect amplitude.Experimental TOF signals under different types of MHD instabilities(sawtooth,sawtooth precursors and tearing mode)are studied in detail and show agreement with the simulation.Two new improved algorithms for detecting and localizing the radial positions of the low-order rational surface,the cross-correlation and gradient threshold(CGT)method and the 2D convolutional neural network approach(CNN)are presented for the first time.It is concluded that TOF signal analysis from profile reflectometry can provide a straightforward and localized measurement of the plasma perturbation from the edge to the core simultaneously and may be a complement or correction to the q-profile control,which will be beneficial for the advanced tokamak operation.展开更多
Surface wave inversion is a key step in the application of surface waves to soil velocity profiling.Currently,a common practice for the process of inversion is that the number of soil layers is assumed to be known bef...Surface wave inversion is a key step in the application of surface waves to soil velocity profiling.Currently,a common practice for the process of inversion is that the number of soil layers is assumed to be known before using heuristic search algorithms to compute the shear wave velocity profile or the number of soil layers is considered as an optimization variable.However,an improper selection of the number of layers may lead to an incorrect shear wave velocity profile.In this study,a deep learning and genetic algorithm hybrid learning procedure is proposed to perform the surface wave inversion without the need to assume the number of soil layers.First,a deep neural network is adapted to learn from a large number of synthetic dispersion curves for inferring the layer number.Then,the shear-wave velocity profile is determined by a genetic algorithm with the known layer number.By applying this procedure to both simulated and real-world cases,the results indicate that the proposed method is reliable and efficient for surface wave inversion.展开更多
Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for ...Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for the verification of free-form surface profile are available, the profile parameters of free-form surface are proposed by referring to ISO standards regarding form tolerances and considering its complexity and non-rotational symmetry. Non-uniform rational basis spline（NURBS） for describing free-form surface is formulated. Crucial issues in surface inspection and profile error verification are localization between the design coordinate system（DCS） and measurement coordinate system（MCS） for searching the closest points on the design model corresponding to measured points. A quasi particle swarm optimization（QPSO） is proposed to search the transformation parameters to implement localization between DCS and MCS. Surface subdivide method which does the searching in a recursively reduced range of the parameters u and v of the NURBS design model is developed to find the closest points. In order to verify the effectiveness of the proposed methods, the design model is generated by NURBS and the measurement data of simulation example are generated by transforming the design model to arbitrary position and orientation, and the parts are machined based on the design model and are measured on CMM. The profile errors of simulation example and actual parts are calculated by the proposed method. The results verify that the evaluation precision of freeform surface profile error by the proposed method is higher 10%-22% than that by CMM software. The proposed method deals with the hard problem that it has a lower precision in profile error evaluation of free-form surface.展开更多
In alloy bar rolling process, the component of alloyed steel influenced the spread coefficient greatly, therefore, the component influence coefficient m of different alloyed steel has been determined firstly to calcul...In alloy bar rolling process, the component of alloyed steel influenced the spread coefficient greatly, therefore, the component influence coefficient m of different alloyed steel has been determined firstly to calculate the maximum spread. Then the curvature radius of stress free surface and the ＂critical point on the contact boundary＂ have been solved, the surface profile of outgoing workpiece has been obtained. Furthermore, the formula of the equivalent contact section area has been proposed and the mean roll radius has been calculated. The bar rolling experiment and the rigid-plastic FEM （finite element method） simulation have been carried out to verify the novel approach. Compared with experimental data and simulation results, the novel approach can be used in setting processing parameter and design of finishing groove.展开更多
The line-of-sight velocity of scattering facets is related to the Doppler signals of X-band coherent marine radar from the oceanic surface. First, the sign Doppler Estimator is applied to estimate the Doppler shift of...The line-of-sight velocity of scattering facets is related to the Doppler signals of X-band coherent marine radar from the oceanic surface. First, the sign Doppler Estimator is applied to estimate the Doppler shift of each radar resolution cell. And then, in terms of the Doppler shift, a retrieval algorithm extracting the vertical displacement of the sea surface has been proposed. The effects induced by radar look-direction and radar spatial resolution are both taken into account in this retrieval algorithm. The comparison between the sea surface spectrum of buoy data and the retrieved spectrum reveals that the function of the radar spatial resolution is equivalent to a low pass filter, impacting especially the spectrum of short gravity waves. The experimental data collected by McMaster IPIX radar are also used to validate the performance of the retrieval algorithm. The derived significant wave height and wave period are compared with the in situ measurements, and the agreement indicates the practicality of the retrieval technology.展开更多
Owing to extensive construction of dams, the impact of backwater on flow may lead to navigation or flood control issues in curved channels. To date, the impact of backwater on the water surface profile in curved chann...Owing to extensive construction of dams, the impact of backwater on flow may lead to navigation or flood control issues in curved channels. To date, the impact of backwater on the water surface profile in curved channels remains unknown and requires investigation. In this study, experiments were conducted in a glass-walled recirculating flume with a length of 19.4 m, a width of 0.6 m, and a depth of 0.8 m, and the impact of backwater on the water surface profile in a 90° channel bend was investigated. The experimental results showed that the backwater degree had a significant impact on the transverse and longitudinal flow depth distributions in the bend. The transverse slope of the flow (Jr) increased linearly with an increase in the Froude number of the approach flow upstream of the bend. Jr increased with the longitudinal location parameter ξ when −0.2 < ξ < 0.5, and decreased with ξ when 0.5 < ξ < 1.2. Furthermore, the results showed that Jr asymptotically decreased to zero with an increase in the degree of backwater. An equation was formulated to estimate the transverse slope of the flow in a 90° bend in backwater zones.展开更多
The surface profile of laser peening with square spots was compared with that of circle spots, and the microstructure of laser peened titanium alloy Ti-6Al-4V in the center of a square spot and at the edge of the squa...The surface profile of laser peening with square spots was compared with that of circle spots, and the microstructure of laser peened titanium alloy Ti-6Al-4V in the center of a square spot and at the edge of the square spot was investigated in this paper. The results show that a smaller size crystal is produced at the edge of square spots because the shearing strain produces nanoscale crystals in laser peening titanium alloy Ti-6Al-4V.展开更多
We study the properties of the intensity profiles scattered from the self-affine fractal random surfaces.We use the mathematical decay function to approximate the duple negative exponent function in the rigorous theor...We study the properties of the intensity profiles scattered from the self-affine fractal random surfaces.We use the mathematical decay function to approximate the duple negative exponent function in the rigorous theory of scattering,by letting them have the same maximum value and half-width,and the expression for the half-widths of the intensity profiles in the whole range of the perpendicular wave vector component is obtained.The previous results in the two extreme cases are included in the results of this paper.In the simulational verification,we propose a method for the generation of self-affine fractal random surfaces,using the square-root of Fourier transform of the correlation function of the surface height.The simulated results conform well with the theory.展开更多
Nitrogen oxides (NO<sub>x</sub>) in urban air close to ground have significant health implications. Restrictions in traffic, mandatory use of catalytic converters on vehicles, and novel photocatalytic coat...Nitrogen oxides (NO<sub>x</sub>) in urban air close to ground have significant health implications. Restrictions in traffic, mandatory use of catalytic converters on vehicles, and novel photocatalytic coatings on surfaces contribute to reducing the level of NO<sub>x</sub> in cities. The aim of this study is to establish environmental profiles of NO<sub>x</sub> removal by a Three-Way Catalyst (TWC) car converter and by a photocatalytic surface coating (for asphalt and concrete pavements) for fostering technological development in reducing the levels of NO<sub>x</sub> in urban air. We assessed the environmental performance for the removal of 1 kg NO<sub>x</sub> by the two technologies with Life Cycle Assessment (LCA;EF.3 impact assessment method). In order to do so, we established Life-Cycle-Inventory (LCI) data representing production, operation and end-of-life of the two technologies based on data from literature and industry. The production of photocatalytic surface coatings, used on concrete and asphalt, has environmental loads two orders of magnitude lower than the environmental benefits of NO<sub>x</sub> reduction expressed as a reduction in Photochemical Ozone Formation (POF), Acidification (A), and Terrestrial Eutrophication (TE). The vehicle catalytic converter shows similar results except that the use of rare earth elements in the production constitutes a significant load to Freshwater Ecotoxicity (FET) and that additional use of fuel during operation induces a modest Climate Change (CC) impact. For both technologies, the environmental benefits of reducing NO<sub>x</sub> far exceed any adverse environmental aspects of the production of the technologies.展开更多
The 850-nm oxide-confined vertical-cavity surface-emitting lasers with petal-shape holey structures are presented. An area-weighted average refractive index model is given to analyse their effective index profiles, an...The 850-nm oxide-confined vertical-cavity surface-emitting lasers with petal-shape holey structures are presented. An area-weighted average refractive index model is given to analyse their effective index profiles, and the graded index distribution in the holey region is demonstrated. The index step between the optical aperture and the holey region is obtained which is related merely to the etching depth. Four types of holey vertical-cavity surface-emitting lasers with different parameters are fabricated as well as the conventional oxide-confined vertical-cavity surface-emitting laser. Compared with the conventional oxide-confined vertical-cavity surface-emitting laser without etched holes, the holey vertical-cavity surface-emitting laser possesses an improved beam quality due to its graded index distribution, but has a lower output power, higher threshold current and lower slope efficiency. With the hole number increased, the holey vertical-cavity surface-emitting laser can realize the single-mode operation throughout the entire current range, and reduces the beam divergence further. The loss mechanism is used to explain the single-mode characteristic, and the reduced beam divergence is attributed to the shallow etching. High coupling efficiency of 86% to a multi-mode fibre is achieved for the single-mode device in the experiment.展开更多
Profile grinding is the most crucial method for the ultra-precision machining of special-shaped surfaces.However,profile grinding produces a unique machining profile,and many random factors in the machining process le...Profile grinding is the most crucial method for the ultra-precision machining of special-shaped surfaces.However,profile grinding produces a unique machining profile,and many random factors in the machining process lead to complex surface characteristics.In this study,the structural and probabilistic characteristics of the profile grinding of a special-shaped surface were analyzed,and a probabilistic algorithm for the forming and 3D characterization of special-shaped surfaces under profile grinding was developed.The forming process of a GH738 blade tenon tooth surface was considered as an example to demonstrate the algorithm.The comparison results showed that the simulation results had similar surface characteristics to the measurement results,and the relative error range of the 3D roughness parameter was 0.21%–19.76%,indicating an accurate prediction and characterization of the complex special-shaped surface under the action of multiple factors.展开更多
A novel analytical model for the thin film silicon on insulator (TFSOI) reduced surface field (RESURF) devices has been proposed.Based on the 2-D Poisson equation solution,the analytical expressions for the surface po...A novel analytical model for the thin film silicon on insulator (TFSOI) reduced surface field (RESURF) devices has been proposed.Based on the 2-D Poisson equation solution,the analytical expressions for the surface potential and field distributions are derived.From this analysis,the optimum design condition for the maximum breakdown voltage is obtained.The dependence of the maximum breakdown voltage on the drift region length is examined and the relationship between the critical doping concentration and the front- and back- interface oxide layer thickness is discussed.The numerical simulation performed by the advanced semiconductor simulation tool,DESSIS-ISE,has been shown to support the analytical results.展开更多
Based on slow- and fast-response measurements under neutral stratification conditions from a 325-m meteorological tower located in a built-up area of north-central Beijing as well as a descriptive survey of surface ro...Based on slow- and fast-response measurements under neutral stratification conditions from a 325-m meteorological tower located in a built-up area of north-central Beijing as well as a descriptive survey of surface roughness elements (i.e., buildings and trees) around the tower site, urban roughness lengths, zo, with zero-plane displacement height are estimated using logarithmic wind profile and morphometric methods in eight 45° directional sectors. When comparing their results with each other, the slow-response method tends to give smaller zo values. At a given location, considerable directional variations in values are observed. The effect of surface roughness on urban turbulence characteristics in terms of non-dimensional standard deviations of three-component velocity, σi/u*1 (where i = u, v, w and u*1 is local friction velocity), is investigated.展开更多
The surface structure and properties are different from those of the bulk, depending on the substrate materials and deposition condition, and playing an important role in precise optical components. The conventional s...The surface structure and properties are different from those of the bulk, depending on the substrate materials and deposition condition, and playing an important role in precise optical components. The conventional spectroscopic methods to monitor the surface structure are restricted only in several layers of molecules. It is known that the penetration depth of the incident light increases with its wavelength and decreases with the angle of incidence. Thus infrared spectroscopy provides a powerful means for determination of surface structure and the depth profile up to micrometers. By recording the reflection spectra at different angles of incidence, the surface structure and its depth profile can be monitored successively. Further, the incident field has the subcomponents parallel and perpendicular to the surface, which excite the transverse and longitudinal optic modes, respectively. Change of the polarization direction of the incident light provides a practical function to study anisotropic property of the surface and the interaction between the transverse and longitudinal optic modes. In this work, infrared spectrophotometer was applied to investigate the depth profile in microstructure of silica glass. Combining with the glass fiber system, this technique can be used for in-situ control of the deposition process. In comparing with ellipsometry, this method reveals both structural and constitutional information.展开更多
This paper proposes a new method to retrieve salinity profiles from the sea surface salinity （SSS） observed by the Soil Moisture and Ocean Salinity （SMOS） satellite. The main vertical patterns of the salinity prof...This paper proposes a new method to retrieve salinity profiles from the sea surface salinity （SSS） observed by the Soil Moisture and Ocean Salinity （SMOS） satellite. The main vertical patterns of the salinity profiles are firstly extracted from the salinity profiles measured by Argo using the empirical orthogonal function. To determine the time coefficients for each vertical pattern, two statistical models are developed. In the linear model, a transfer function is proposed to relate the SSS observed by SMOS （SMOS_SSS） with that measured by Argo, and then a linear relationship between the SMOS_SSS and the time coefficient is established. In the nonlinear model, the neural network is utilized to estimate the time coefficients from SMOS_SSS, months and positions of the salinity profiles. The two models are validated by comparing the salinity profiles retrieved from SMOS with those measured by Argo and the climatological salinities. The root-mean-square error （RMSE） of the linear and nonlinear model are 0.08-0.16 and 0.08-0.14 for the upper 400 m, which are 0.01-0.07 and 0.01-0.09 smaller than the RMSE of climatology. The error sources of the method are also discussed.展开更多
The measurement of the surface quality and the profile preciseness is major issues in many industrial branches such that the surface quality of semi products directly affects the subsequent production steps.Although,t...The measurement of the surface quality and the profile preciseness is major issues in many industrial branches such that the surface quality of semi products directly affects the subsequent production steps.Although,there are many ways to obtain required data,the hardware necessary for the measurements such as 2D or 3D scanners,depending on the problem’s complexity,is too expensive.Therefore,in this paper,what we put forward as a novelty is an algorithm which is verified on the model of simple 3D scanner on the image processing basis with the resolution of 0.1 mm.There are many ways to scan surface profile;however,the image processing currently is the most trending topic in industry automation.Most importantly,in order to obtain surface images,standard high resolution reflex camera is used and thus the post processing could be realized with MatLab as the software environment.Therefore,this solution is an alternative to the expensive scanners,and single-purpose devices could be extended by many additional functions.展开更多
In this paper, towing tank experiments are conducted to study the behavior of flow on a model of the underwater vehicle with various shapes of bows, i.e. tango and standard bows in free surface motion tests. The total...In this paper, towing tank experiments are conducted to study the behavior of flow on a model of the underwater vehicle with various shapes of bows, i.e. tango and standard bows in free surface motion tests. The total resistances for different Froude numbers are considered experimentally. The towing tank is equipped with a trolley that can operate in through 0.05-6 m/s speed with ±0.02 m/s accuracy. Furthermore, the study is done on hydrodynamic coefficients i.e. total, residual and friction resistance coefficients, and the results are compared. Finally, the study on flow of wave fields around bows is done and wave filed around two bows are compared. The Froude number interval is between 0.099 and 0.349. Blockage fraction for the model is fixed to 0.005 3. The results showed that the residual resistance of the standard bow in 0.19 to 0.3 Froude number is more than the tango bow in surface motion which causes more total resistance for the submarine. Finally, details of wave generated by the bow are depicted and the effects of flow pattern on resistance drag are discussed.展开更多
Ocean sound speed profile(SSP) is the key factor affecting acoustic propagation. The acquisition of SSPsin real time with high precision is meaningful for underwater activities. By means of the remote sensing method, ...Ocean sound speed profile(SSP) is the key factor affecting acoustic propagation. The acquisition of SSPsin real time with high precision is meaningful for underwater activities. By means of the remote sensing method, thesea surface data could be obtained in near-real time. Typically, the subsurface fields are correlated with the sea surfaceparameters. Thus, the SSPs could be obtained by means of satellite remote sensing. In this paper, the history as wellas the current research over the reconstruction of subsurface fields by means of sea surface data is introduced. Thentwo methods to reconstruct the SSPs with sea surface data, including the linear regression method using the empiricalorthogonal function, and the self-organizing method based on the big data theory, are described in detail in the paper.展开更多
We make use of the images from the Sloan Digital Sky Survey Stripe 82（Stripe 82） to present an analysis of r band surface brightness profiles and radial color gradients（g-r,u-r） in our sample of 111 nearby early-t...We make use of the images from the Sloan Digital Sky Survey Stripe 82（Stripe 82） to present an analysis of r band surface brightness profiles and radial color gradients（g-r,u-r） in our sample of 111 nearby early-type galaxies（ETGs） .Thanks to the Stripe 82 images,each of which is co-added from about 50 single frames,we are able to pay special attention to the low-surface-brightness areas（LSB areas） of the galaxies.The LSB areas affect the Sérsic fittings and concentration indices by making both of the indices less than the typical values for ETGs.In the Sérsic fits to all the surface brightness profiles,we found some Sérsic indices that range from 1.5 to 2.5,much smaller than those of typical de Vaucouleur profiles and relatively close to those of exponential disks,and some others much larger than four but still with accurate fitting.Two galaxies cannot be fitted with a single Sérsic profile,but once we try double Sérsic profiles,the fittings are improved：one with a profile relatively close to the de Vaucouleur law in the inner area and a profile relatively close to an exponential law in the LSB area,the other with a nice fitting in the inner area but still having a failed fitting in the outer area.About 60%of the sample has negative color gradients（red-core） within 1.5Re,much more than the approximately 10%positive ones（blue-core） within the same radius.However,taking into account the LSB areas,we find that the color gradients are not necessarily monotonic：about one third of the red-core（or blue-core） galaxies have positive（or negative） color gradients in the outer areas. So LSB areas not only make ETGs’Sérsic profiles deviate from de Vaucouleur ones and shift to the disk end,but also reveal that quite a number of ETGs have opposite color gradients in inner and outer areas.These outcomes remind us of the necessity of double-Sérsic fitting.These LSB phenomena may be interpreted by mergers and thus have different metallicity in the outer areas.Isophotal parameters are also discussed briefly in this paper with the following conclusion：there are more disky nearby ETGs that are identified than boxy ones.展开更多
基金Supported by National Natural Science Foundation of China (Grant No.52275061)。
文摘Profile shift is a highly effective technique for optimizing the performance of spur gear transmission systems.However,tooth surface wear is inevitable during gear meshing due to inadequate lubrication and long-term operation.Both profile shift and tooth surface wear(TSW)can impact the meshing characteristics by altering the involute tooth profile.In this study,a tooth stiffness model of spur gears that incorporates profile shift,TSW,tooth deformation,tooth contact deformation,fillet-foundation deformation,and gear body structure coupling is established.This model efficiently and accurately determines the time-varying mesh stiffness(TVMS).Additionally,an improved wear depth prediction method for spur gears is developed,which takes into consideration the mutually prime teeth numbers and more accurately reflects actual gear meshing conditions.Results show that consideration of the mutual prime of teeth numbers will have a certain impact on the TSW process.Furthermore,the finite element method(FEM)is employed to accurately verify the values of TVMS and load sharing ratio(LSR)of profile-shifted gears and worn gears.This study quantitatively analyzes the effect of profile shift on the surface wear process,which suggests that gear profile shift can partially alleviate the negative effects of TSW.The contribution of this study provides valuable insights into the design and maintenance of spur gear systems.
基金supported by the Open Fund of Magnetic Confinement Laboratory of Anhui Province(No.2023 AMF03005)the China Postdoctoral Science Foundation(No.2021M703256)+4 种基金the Director Funding of Hefei Institutes of Physical Science,Chinese Academy of Sciences(No.YZJJ2022QN16)the National Key R&D Program of China(Nos.2022YFE03050003,2019YFE03080200,2019Y FE03040002,and 2022YFE03070004)National Natural Science Foundation of China(Nos.12075284,12175277,12275315 and 12275311)the National Magnetic Confinement Fusion Science Program of China(No.2022YFE03040001)the Science Foundation of the Institute of Plasma Physics,Chinese Academy of Sciences(No.DSJJ-2021-08)。
文摘Microwave reflectometry is a powerful diagnostic that can measure the density profile and localized turbulence with high spatial and temporal resolution and will be used in ITER,so understanding the influence of plasma perturbations on the reflect signal is important.The characteristics of the reflect signal from profile reflectometry,the time-of-flight(TOF)signal associated with the MHD instabilities,are investigated in EAST.Using a 1D full-wave simulation code by the Finite-DifferenceTime-Domain(FDTD)method,it is well validated that the local density flattening could induce the discontinuity of the simulated TOF signal and an obvious change of reflect amplitude.Experimental TOF signals under different types of MHD instabilities(sawtooth,sawtooth precursors and tearing mode)are studied in detail and show agreement with the simulation.Two new improved algorithms for detecting and localizing the radial positions of the low-order rational surface,the cross-correlation and gradient threshold(CGT)method and the 2D convolutional neural network approach(CNN)are presented for the first time.It is concluded that TOF signal analysis from profile reflectometry can provide a straightforward and localized measurement of the plasma perturbation from the edge to the core simultaneously and may be a complement or correction to the q-profile control,which will be beneficial for the advanced tokamak operation.
基金provided through research grant No.0035/2019/A1 from the Science and Technology Development Fund,Macao SARthe assistantship from the Faculty of Science and Technology,University of Macao。
文摘Surface wave inversion is a key step in the application of surface waves to soil velocity profiling.Currently,a common practice for the process of inversion is that the number of soil layers is assumed to be known before using heuristic search algorithms to compute the shear wave velocity profile or the number of soil layers is considered as an optimization variable.However,an improper selection of the number of layers may lead to an incorrect shear wave velocity profile.In this study,a deep learning and genetic algorithm hybrid learning procedure is proposed to perform the surface wave inversion without the need to assume the number of soil layers.First,a deep neural network is adapted to learn from a large number of synthetic dispersion curves for inferring the layer number.Then,the shear-wave velocity profile is determined by a genetic algorithm with the known layer number.By applying this procedure to both simulated and real-world cases,the results indicate that the proposed method is reliable and efficient for surface wave inversion.
基金supported by National Natural Science Foundation of China(Grant No. 51075198)Jiangsu Provincial Natural Science Foundation of China(Grant No. BK2010479)+1 种基金Jiangsu Provincial Project of 333 Talents Engineering of ChinaJiangsu Provincial Project of Six Talented Peak of China
文摘Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for the verification of free-form surface profile are available, the profile parameters of free-form surface are proposed by referring to ISO standards regarding form tolerances and considering its complexity and non-rotational symmetry. Non-uniform rational basis spline（NURBS） for describing free-form surface is formulated. Crucial issues in surface inspection and profile error verification are localization between the design coordinate system（DCS） and measurement coordinate system（MCS） for searching the closest points on the design model corresponding to measured points. A quasi particle swarm optimization（QPSO） is proposed to search the transformation parameters to implement localization between DCS and MCS. Surface subdivide method which does the searching in a recursively reduced range of the parameters u and v of the NURBS design model is developed to find the closest points. In order to verify the effectiveness of the proposed methods, the design model is generated by NURBS and the measurement data of simulation example are generated by transforming the design model to arbitrary position and orientation, and the parts are machined based on the design model and are measured on CMM. The profile errors of simulation example and actual parts are calculated by the proposed method. The results verify that the evaluation precision of freeform surface profile error by the proposed method is higher 10%-22% than that by CMM software. The proposed method deals with the hard problem that it has a lower precision in profile error evaluation of free-form surface.
文摘In alloy bar rolling process, the component of alloyed steel influenced the spread coefficient greatly, therefore, the component influence coefficient m of different alloyed steel has been determined firstly to calculate the maximum spread. Then the curvature radius of stress free surface and the ＂critical point on the contact boundary＂ have been solved, the surface profile of outgoing workpiece has been obtained. Furthermore, the formula of the equivalent contact section area has been proposed and the mean roll radius has been calculated. The bar rolling experiment and the rigid-plastic FEM （finite element method） simulation have been carried out to verify the novel approach. Compared with experimental data and simulation results, the novel approach can be used in setting processing parameter and design of finishing groove.
基金The National Natural Science Foundation of China under contract Nos 41376179 and 41106153the National Natural Science Foundation of China-Shandong Joint Fund for Marine Science Research Centers under contract No.U1406404
文摘The line-of-sight velocity of scattering facets is related to the Doppler signals of X-band coherent marine radar from the oceanic surface. First, the sign Doppler Estimator is applied to estimate the Doppler shift of each radar resolution cell. And then, in terms of the Doppler shift, a retrieval algorithm extracting the vertical displacement of the sea surface has been proposed. The effects induced by radar look-direction and radar spatial resolution are both taken into account in this retrieval algorithm. The comparison between the sea surface spectrum of buoy data and the retrieved spectrum reveals that the function of the radar spatial resolution is equivalent to a low pass filter, impacting especially the spectrum of short gravity waves. The experimental data collected by McMaster IPIX radar are also used to validate the performance of the retrieval algorithm. The derived significant wave height and wave period are compared with the in situ measurements, and the agreement indicates the practicality of the retrieval technology.
基金supported by the National Key Research and Development Program of China(Grant No.2019YFC1510701)the National Natural Science Foundation of China(Grant No.U20A20319).
文摘Owing to extensive construction of dams, the impact of backwater on flow may lead to navigation or flood control issues in curved channels. To date, the impact of backwater on the water surface profile in curved channels remains unknown and requires investigation. In this study, experiments were conducted in a glass-walled recirculating flume with a length of 19.4 m, a width of 0.6 m, and a depth of 0.8 m, and the impact of backwater on the water surface profile in a 90° channel bend was investigated. The experimental results showed that the backwater degree had a significant impact on the transverse and longitudinal flow depth distributions in the bend. The transverse slope of the flow (Jr) increased linearly with an increase in the Froude number of the approach flow upstream of the bend. Jr increased with the longitudinal location parameter ξ when −0.2 < ξ < 0.5, and decreased with ξ when 0.5 < ξ < 1.2. Furthermore, the results showed that Jr asymptotically decreased to zero with an increase in the degree of backwater. An equation was formulated to estimate the transverse slope of the flow in a 90° bend in backwater zones.
文摘The surface profile of laser peening with square spots was compared with that of circle spots, and the microstructure of laser peened titanium alloy Ti-6Al-4V in the center of a square spot and at the edge of the square spot was investigated in this paper. The results show that a smaller size crystal is produced at the edge of square spots because the shearing strain produces nanoscale crystals in laser peening titanium alloy Ti-6Al-4V.
文摘We study the properties of the intensity profiles scattered from the self-affine fractal random surfaces.We use the mathematical decay function to approximate the duple negative exponent function in the rigorous theory of scattering,by letting them have the same maximum value and half-width,and the expression for the half-widths of the intensity profiles in the whole range of the perpendicular wave vector component is obtained.The previous results in the two extreme cases are included in the results of this paper.In the simulational verification,we propose a method for the generation of self-affine fractal random surfaces,using the square-root of Fourier transform of the correlation function of the surface height.The simulated results conform well with the theory.
文摘Nitrogen oxides (NO<sub>x</sub>) in urban air close to ground have significant health implications. Restrictions in traffic, mandatory use of catalytic converters on vehicles, and novel photocatalytic coatings on surfaces contribute to reducing the level of NO<sub>x</sub> in cities. The aim of this study is to establish environmental profiles of NO<sub>x</sub> removal by a Three-Way Catalyst (TWC) car converter and by a photocatalytic surface coating (for asphalt and concrete pavements) for fostering technological development in reducing the levels of NO<sub>x</sub> in urban air. We assessed the environmental performance for the removal of 1 kg NO<sub>x</sub> by the two technologies with Life Cycle Assessment (LCA;EF.3 impact assessment method). In order to do so, we established Life-Cycle-Inventory (LCI) data representing production, operation and end-of-life of the two technologies based on data from literature and industry. The production of photocatalytic surface coatings, used on concrete and asphalt, has environmental loads two orders of magnitude lower than the environmental benefits of NO<sub>x</sub> reduction expressed as a reduction in Photochemical Ozone Formation (POF), Acidification (A), and Terrestrial Eutrophication (TE). The vehicle catalytic converter shows similar results except that the use of rare earth elements in the production constitutes a significant load to Freshwater Ecotoxicity (FET) and that additional use of fuel during operation induces a modest Climate Change (CC) impact. For both technologies, the environmental benefits of reducing NO<sub>x</sub> far exceed any adverse environmental aspects of the production of the technologies.
基金supported by the National Key Basic Research Special Foundation of China (Grant No. 2011CB922000)the National Natural Science Foundation of China (Grant Nos. 61025025 and 60838003)the National High Technology Research and Development Program of China (Grant Nos. 2007AA03Z410 and 2007AA03Z408)
文摘The 850-nm oxide-confined vertical-cavity surface-emitting lasers with petal-shape holey structures are presented. An area-weighted average refractive index model is given to analyse their effective index profiles, and the graded index distribution in the holey region is demonstrated. The index step between the optical aperture and the holey region is obtained which is related merely to the etching depth. Four types of holey vertical-cavity surface-emitting lasers with different parameters are fabricated as well as the conventional oxide-confined vertical-cavity surface-emitting laser. Compared with the conventional oxide-confined vertical-cavity surface-emitting laser without etched holes, the holey vertical-cavity surface-emitting laser possesses an improved beam quality due to its graded index distribution, but has a lower output power, higher threshold current and lower slope efficiency. With the hole number increased, the holey vertical-cavity surface-emitting laser can realize the single-mode operation throughout the entire current range, and reduces the beam divergence further. The loss mechanism is used to explain the single-mode characteristic, and the reduced beam divergence is attributed to the shallow etching. High coupling efficiency of 86% to a multi-mode fibre is achieved for the single-mode device in the experiment.
基金sponsored by the National Natural Science Foundation of China(Grant No.51905442)the National Major Science and Technology Projects of China(Grant No.2017-VII-0002-0095).
文摘Profile grinding is the most crucial method for the ultra-precision machining of special-shaped surfaces.However,profile grinding produces a unique machining profile,and many random factors in the machining process lead to complex surface characteristics.In this study,the structural and probabilistic characteristics of the profile grinding of a special-shaped surface were analyzed,and a probabilistic algorithm for the forming and 3D characterization of special-shaped surfaces under profile grinding was developed.The forming process of a GH738 blade tenon tooth surface was considered as an example to demonstrate the algorithm.The comparison results showed that the simulation results had similar surface characteristics to the measurement results,and the relative error range of the 3D roughness parameter was 0.21%–19.76%,indicating an accurate prediction and characterization of the complex special-shaped surface under the action of multiple factors.
文摘A novel analytical model for the thin film silicon on insulator (TFSOI) reduced surface field (RESURF) devices has been proposed.Based on the 2-D Poisson equation solution,the analytical expressions for the surface potential and field distributions are derived.From this analysis,the optimum design condition for the maximum breakdown voltage is obtained.The dependence of the maximum breakdown voltage on the drift region length is examined and the relationship between the critical doping concentration and the front- and back- interface oxide layer thickness is discussed.The numerical simulation performed by the advanced semiconductor simulation tool,DESSIS-ISE,has been shown to support the analytical results.
文摘Based on slow- and fast-response measurements under neutral stratification conditions from a 325-m meteorological tower located in a built-up area of north-central Beijing as well as a descriptive survey of surface roughness elements (i.e., buildings and trees) around the tower site, urban roughness lengths, zo, with zero-plane displacement height are estimated using logarithmic wind profile and morphometric methods in eight 45° directional sectors. When comparing their results with each other, the slow-response method tends to give smaller zo values. At a given location, considerable directional variations in values are observed. The effect of surface roughness on urban turbulence characteristics in terms of non-dimensional standard deviations of three-component velocity, σi/u*1 (where i = u, v, w and u*1 is local friction velocity), is investigated.
基金This work was supported by the Cheung Kong Scholars Program and the National High Technology Research and Development(863)Program of China.
文摘The surface structure and properties are different from those of the bulk, depending on the substrate materials and deposition condition, and playing an important role in precise optical components. The conventional spectroscopic methods to monitor the surface structure are restricted only in several layers of molecules. It is known that the penetration depth of the incident light increases with its wavelength and decreases with the angle of incidence. Thus infrared spectroscopy provides a powerful means for determination of surface structure and the depth profile up to micrometers. By recording the reflection spectra at different angles of incidence, the surface structure and its depth profile can be monitored successively. Further, the incident field has the subcomponents parallel and perpendicular to the surface, which excite the transverse and longitudinal optic modes, respectively. Change of the polarization direction of the incident light provides a practical function to study anisotropic property of the surface and the interaction between the transverse and longitudinal optic modes. In this work, infrared spectrophotometer was applied to investigate the depth profile in microstructure of silica glass. Combining with the glass fiber system, this technique can be used for in-situ control of the deposition process. In comparing with ellipsometry, this method reveals both structural and constitutional information.
基金The Startup Foundation for Introducing Talent of Nanjing University of Information Science and Technology under contract No.S8113078001
文摘This paper proposes a new method to retrieve salinity profiles from the sea surface salinity （SSS） observed by the Soil Moisture and Ocean Salinity （SMOS） satellite. The main vertical patterns of the salinity profiles are firstly extracted from the salinity profiles measured by Argo using the empirical orthogonal function. To determine the time coefficients for each vertical pattern, two statistical models are developed. In the linear model, a transfer function is proposed to relate the SSS observed by SMOS （SMOS_SSS） with that measured by Argo, and then a linear relationship between the SMOS_SSS and the time coefficient is established. In the nonlinear model, the neural network is utilized to estimate the time coefficients from SMOS_SSS, months and positions of the salinity profiles. The two models are validated by comparing the salinity profiles retrieved from SMOS with those measured by Argo and the climatological salinities. The root-mean-square error （RMSE） of the linear and nonlinear model are 0.08-0.16 and 0.08-0.14 for the upper 400 m, which are 0.01-0.07 and 0.01-0.09 smaller than the RMSE of climatology. The error sources of the method are also discussed.
基金Project(2102–2020)supported by the SPEV Project,University of Hradec Kralove,FIM,Czech RepublicProject(Vot-20H04)supported by Universiti Teknologi Malaysia(UTM)+1 种基金Project(Vot 4L876)supported by Malaysia Research University Network(MRUN)Project(Vot 5F073)supported by the Fundamental Research Grant Scheme(FRGS),Ministry of Education Malaysia。
文摘The measurement of the surface quality and the profile preciseness is major issues in many industrial branches such that the surface quality of semi products directly affects the subsequent production steps.Although,there are many ways to obtain required data,the hardware necessary for the measurements such as 2D or 3D scanners,depending on the problem’s complexity,is too expensive.Therefore,in this paper,what we put forward as a novelty is an algorithm which is verified on the model of simple 3D scanner on the image processing basis with the resolution of 0.1 mm.There are many ways to scan surface profile;however,the image processing currently is the most trending topic in industry automation.Most importantly,in order to obtain surface images,standard high resolution reflex camera is used and thus the post processing could be realized with MatLab as the software environment.Therefore,this solution is an alternative to the expensive scanners,and single-purpose devices could be extended by many additional functions.
文摘In this paper, towing tank experiments are conducted to study the behavior of flow on a model of the underwater vehicle with various shapes of bows, i.e. tango and standard bows in free surface motion tests. The total resistances for different Froude numbers are considered experimentally. The towing tank is equipped with a trolley that can operate in through 0.05-6 m/s speed with ±0.02 m/s accuracy. Furthermore, the study is done on hydrodynamic coefficients i.e. total, residual and friction resistance coefficients, and the results are compared. Finally, the study on flow of wave fields around bows is done and wave filed around two bows are compared. The Froude number interval is between 0.099 and 0.349. Blockage fraction for the model is fixed to 0.005 3. The results showed that the residual resistance of the standard bow in 0.19 to 0.3 Froude number is more than the tango bow in surface motion which causes more total resistance for the submarine. Finally, details of wave generated by the bow are depicted and the effects of flow pattern on resistance drag are discussed.
文摘Ocean sound speed profile(SSP) is the key factor affecting acoustic propagation. The acquisition of SSPsin real time with high precision is meaningful for underwater activities. By means of the remote sensing method, thesea surface data could be obtained in near-real time. Typically, the subsurface fields are correlated with the sea surfaceparameters. Thus, the SSPs could be obtained by means of satellite remote sensing. In this paper, the history as wellas the current research over the reconstruction of subsurface fields by means of sea surface data is introduced. Thentwo methods to reconstruct the SSPs with sea surface data, including the linear regression method using the empiricalorthogonal function, and the self-organizing method based on the big data theory, are described in detail in the paper.
基金Supported by the National Fund for Fostering Talents of Basic Sciences of China
文摘We make use of the images from the Sloan Digital Sky Survey Stripe 82（Stripe 82） to present an analysis of r band surface brightness profiles and radial color gradients（g-r,u-r） in our sample of 111 nearby early-type galaxies（ETGs） .Thanks to the Stripe 82 images,each of which is co-added from about 50 single frames,we are able to pay special attention to the low-surface-brightness areas（LSB areas） of the galaxies.The LSB areas affect the Sérsic fittings and concentration indices by making both of the indices less than the typical values for ETGs.In the Sérsic fits to all the surface brightness profiles,we found some Sérsic indices that range from 1.5 to 2.5,much smaller than those of typical de Vaucouleur profiles and relatively close to those of exponential disks,and some others much larger than four but still with accurate fitting.Two galaxies cannot be fitted with a single Sérsic profile,but once we try double Sérsic profiles,the fittings are improved：one with a profile relatively close to the de Vaucouleur law in the inner area and a profile relatively close to an exponential law in the LSB area,the other with a nice fitting in the inner area but still having a failed fitting in the outer area.About 60%of the sample has negative color gradients（red-core） within 1.5Re,much more than the approximately 10%positive ones（blue-core） within the same radius.However,taking into account the LSB areas,we find that the color gradients are not necessarily monotonic：about one third of the red-core（or blue-core） galaxies have positive（or negative） color gradients in the outer areas. So LSB areas not only make ETGs’Sérsic profiles deviate from de Vaucouleur ones and shift to the disk end,but also reveal that quite a number of ETGs have opposite color gradients in inner and outer areas.These outcomes remind us of the necessity of double-Sérsic fitting.These LSB phenomena may be interpreted by mergers and thus have different metallicity in the outer areas.Isophotal parameters are also discussed briefly in this paper with the following conclusion：there are more disky nearby ETGs that are identified than boxy ones.
