The sub-land/sub-pit affects the characteristic of the tracking error signal which is generated by the conventional differential phase detection （DPD） method in the signal waveform modulation multi-level （SWML） re...The sub-land/sub-pit affects the characteristic of the tracking error signal which is generated by the conventional differential phase detection （DPD） method in the signal waveform modulation multi-level （SWML） read-only disc. To solve this problem, this paper proposes a new tracking error detection method using amplitude difference. Based on the diffraction theory, the amplitude difference is proportional to the tracking error and is feasible to be used for obtaining the off-track information. The experimental system of the amplitude difference detection method is developed. The experimental results show that the tracking error signal derived from the new method has better performance in uniformity and signal-to-noise ratio than that derived from the conventional DPD method in the SWML read-only disc.展开更多
In order to solve problems in high dynamic environment, a frequency-locked loop （FLL） assisted phase-locked loop （PLL） is put forward for carrier tracking. On the basis of the analysis of discriminators, the total...In order to solve problems in high dynamic environment, a frequency-locked loop （FLL） assisted phase-locked loop （PLL） is put forward for carrier tracking. On the basis of the analysis of discriminators, the total phase error of the tracking loop is analyzed and a general error expression is derived. By using linearization and Jaffe-Rechtin coefficients, the performance of a special first order FLL-assisted second order PLL is analyzed to get a closed expression. Analysis results and simula- tions show that there exist an optimal FLL loop bandwidth and a optimal PLL loop bandwidth which can make the phase jitter much less than that when the PLL is used alone.展开更多
The aim of this study was to predict drivers＇ drowsy states with high risk of encountering a crash and prevent drivers from continuing to drive under such drowsy states with high risk of crash. While the participants...The aim of this study was to predict drivers＇ drowsy states with high risk of encountering a crash and prevent drivers from continuing to drive under such drowsy states with high risk of crash. While the participants were required to carry out a simulated driving task, EEG （Electro encephalography） （EEG-MPF and EEG-α/β）, ECG （Electrocradiogram） （RRV3）, t racking error, an d subjective rating on drowsiness were measured. On the basis of such measurements, an attempt was made to predict the point in time with high crash risk using Bayesian estimation of posterior probability of drowsiness, tracking error, and subjective drowsiness. As a result of applying the proposed method to the data of each participant, it was verified that the proposed method could predict the point in time with high crash risk before the point in time of crash.展开更多
Small tracking error correction for electro-optical systems is essential to improve the tracking precision of future mechanical and defense technology.Aerial threats,such as“low,slow,and small(LSS)”moving targets,po...Small tracking error correction for electro-optical systems is essential to improve the tracking precision of future mechanical and defense technology.Aerial threats,such as“low,slow,and small(LSS)”moving targets,pose increasing challenges to society.The core goal of this work is to address the issues,such as small tracking error correction and aiming control,of electro-optical detection systems by using mechatronics drive modeling,composite velocity–image stability control,and improved interpolation filter design.A tracking controller delay prediction method for moving targets is proposed based on the Euler transformation model of a two-axis,two-gimbal cantilever beam coaxial configuration.Small tracking error formation is analyzed in detail to reveal the scientific mechanism of composite control between the tracking controller’s feedback and the motor’s velocity–stability loop.An improved segmental interpolation filtering algorithm is established by combining line of sight(LOS)position correction and multivariable typical tracking fault diagnosis.Then,a platform with 2 degrees of freedom is used to test the system.An LSS moving target shooting object with a tracking distance of S=100 m,target board area of A=1 m^(2),and target linear velocity of v=5 m/s is simulated.Results show that the optimal method’s distribution probability of the tracking error in a circle with a radius of 1 mrad is 66.7%,and that of the traditional method is 41.6%.Compared with the LOS shooting accuracy of the traditional method,the LOS shooting accuracy of the optimized method is improved by 37.6%.展开更多
Purpose The Space Environment Simulation and Research Infrastructure(SESRI)is a cluster of accelerators designed to simulate the cosmic radiation environment by generating particles of various types and energies.Among...Purpose The Space Environment Simulation and Research Infrastructure(SESRI)is a cluster of accelerators designed to simulate the cosmic radiation environment by generating particles of various types and energies.Among these accelerators,a synchrotron in the 300 MeV proton and heavy ion accelerator complex utilizes a multiturn injection scheme with four bump magnets to accumulate proton and heavy ion beams effectively.However,the bump magnetic field experiences a rapid drop rate of up to 1000 T/s,inevitably leading to a deviation(field tracking error)from the ideal magnetic field.The injection efficiency and particle distribution are significantly affected by this field tracking error,as evaluated by the ACCSIM code.Method During the device testing stage,the sources of field tracking errors were identified by analysis of the bump power supplies and the field of the magnets.Mitigation techniques were then implemented to reduce the field tracking error from[Math Processing Error]to[Math Processing Error]throughout the entire power supply,transmission cable,and magnet chain.Results Moreover,the successful injection and accumulation of beams during the operational phase of the synchrotron confirmed the effectiveness of the proposed mitigation methods.Additionally,a magnetic field measurement system was developed to monitor the magnetic field tracking error online.Conclusion The combination of the field tracking error mitigation methods and the measurement system provides valuable guidance for optimizing the magnetic fields with rapid drop rates.展开更多
In this paper,the problem of time optimal feedrate generation under confined feedrate,axis accelerations,and axis tracking errors is considered.The main contribution is to reduce the tracking error constraint to const...In this paper,the problem of time optimal feedrate generation under confined feedrate,axis accelerations,and axis tracking errors is considered.The main contribution is to reduce the tracking error constraint to constraints about the axis velocities and accelerations,when the tracking error satisfies a second order linear ordinary differential equation.Based on this simplification on the tracking error,the original feedrate generation problem is reduced to a new form which can be efficiently solved with linear programming algorithms.Simulation results are used to validate the methods.展开更多
In this paper,a method of reducing the tracking error in CNC machining is proposed.The structured neural network is used to approximate the discontinuous friction in CNC machining,which has jump points and uncertainti...In this paper,a method of reducing the tracking error in CNC machining is proposed.The structured neural network is used to approximate the discontinuous friction in CNC machining,which has jump points and uncertainties.With the estimated nonlinear friction function,the reshaped trajectory can be computed from the desired one by solving a second order ODE such that when the reshaped trajectory is fed into the CNC controller,the output is the desired trajectory and the tracking error is eliminated in certain sense.The proposed reshape method is also shown to be robust with respect to certain parameters of the dynamic system.展开更多
Laser tracking system （LTS） is an advanced device for large size 3D coordinates measuring with the advantages of broad range, high speed and high accuracy. However, its measuring accuracy is highly dominated by the ...Laser tracking system （LTS） is an advanced device for large size 3D coordinates measuring with the advantages of broad range, high speed and high accuracy. However, its measuring accuracy is highly dominated by the geometric errors of the tracking mirror mechanism. Proper calibration of LTS is essential prior to the use of it for metrology. A kinematics model that describes not only the motion but also the geometric variations of LTS is developed. Through error analysis of the proposed model, it is claimed that gimbals axis misalignments and tracking mirror center off-set are the key contributors to measuring errors of LTS. A self-calibration method is presented of calibrating LTS with planar constraints. Various calibration strategies utilizing single-plane and multiple-plane constraints are proposed for different situations. For each calibration strategy, issues about the error parameter estimation of LTS are exploded to find out in which conditions these parameters can be uniquely estimated. Moreover, these conditions reveal the applicability of the planar constraints to LTS self-calibration. Intensive studies have been made to check validity of the theoretical results. The results show that the measuring accuracy of LTS has increased by 5 times since this technique for calibration is used.展开更多
The Rapid Cycling Synchrotron （RCS） is a key component of the China Spallation Neutron Source （CSNS）. For this type of high intensity proton synchrotron, the chromaticity, space charge effects, and magnetic field ...The Rapid Cycling Synchrotron （RCS） is a key component of the China Spallation Neutron Source （CSNS）. For this type of high intensity proton synchrotron, the chromaticity, space charge effects, and magnetic field tracking errors between the quadrupoles and the dipoles can induce beta function distortion and tune shift, and induce resonances. In this paper, the combined effects of chromaticity, magnetic field tracking errors and space charge on beam dynamics at CSNS/RCS are studied systemically. 3-D simulations with different magnetic field tracking errors are performed by using the code ORBIT, and the simulation results are compared with the case without tracking errors.展开更多
Radar leveling system is the key equipment for improving the radar mobility and survival capability. A combined quantitative feedback theory (QFT) controller is designed for the radar truck leveling simulator in this ...Radar leveling system is the key equipment for improving the radar mobility and survival capability. A combined quantitative feedback theory (QFT) controller is designed for the radar truck leveling simulator in this paper, which suffers from strong nonlinearities and system parameter uncertainties. QFT can reduce the plant uncertainties and stabilize the system, but it fails to obtain high-precision tracking. This drawback can be solved by a robust QFT control scheme based on zero phase error tracking control (ZPETC) compensation. The combined controller not only possesses high robustness, but greatly improves the system performance. To verify the effiectiveness and the potential of the proposed controller, a series of experiments have been carried out. Experimental results have demonstrated its robustness against a large range of parameters variation and high tracking precision performance, as well as its capability of restraining the load coupling among channels. The combined QFT controller can drive the radar truck leveling platform accurately, quickly and stably.展开更多
To track the narrow butt welding seams in container manufacture, a visual tracking system based on smart camera is proposed in this paper. A smart camera is used as the sensor to detect the welding seam. The feature e...To track the narrow butt welding seams in container manufacture, a visual tracking system based on smart camera is proposed in this paper. A smart camera is used as the sensor to detect the welding seam. The feature extraction algorithm is designed with the consideration of the characteristics of the smart caraera, which is used to compute the error between the welding torch and the welding seam. Visual control system based on image is preseated, which employs a programmable controller to control a stepper motor to eliminate the tracking error detected by the smart camera. Experiments are conducted to demonstrate the effectiveness of the vision system.展开更多
The contour error was analyzed based on CNC multi-axis motion control, the contour error model was obtained focused on beeline and different radius of curvature and common contour of curve, for a CNC biaxial motion co...The contour error was analyzed based on CNC multi-axis motion control, the contour error model was obtained focused on beeline and different radius of curvature and common contour of curve, for a CNC biaxial motion control system and the mechanism of producing contour error and the relationship between tracking error and contour error were presented. The theoretical and practical significance of modeling error and controlling error in motion control systems was carried out.展开更多
Vector tracking changes the classical structure of receivers. Combining signal tracking and navigation solution,vector tracking can realize powerful processing capabilities by the fusion technique of receiving channel...Vector tracking changes the classical structure of receivers. Combining signal tracking and navigation solution,vector tracking can realize powerful processing capabilities by the fusion technique of receiving channel and feedback correction. In this paper,we try to break through the complicated details of numerical analysis,consider the overall influencing factors of the residual in observed data,and use the intrinsic link between a conventional receiver and a vector receiver. A simple method for performance analysis of the vector tracking algorithm is proposed. Kalman filter has the same steady performance with the classic digital lock loop through the analysis of the relation between gain and band width. The theoretical analysis by the least squares model shows that the reduction of range error is the basis for the superior performance realized by vector tracking. Thus,the bounds of its performance enhancement under weak signal and highly dynamic conditions can be deduced. Simulation results verify the effectiveness of the analysis presented here.展开更多
The Qi Tai Telescope(QTT),which has a 110 m aperture,is planned to be the largest scale steerable tele-scope in the world.Ideally,the telescope’s repeated pointing accuracy error should be less than 2.5 arc seconds(a...The Qi Tai Telescope(QTT),which has a 110 m aperture,is planned to be the largest scale steerable tele-scope in the world.Ideally,the telescope’s repeated pointing accuracy error should be less than 2.5 arc seconds(arcsec);thus,the telescope structure must satisfy ultra-high precision requirements.In this pur-suit,the present research envisages a reverse-design method for the track surface to reduce the difficulty of the telescope’s design and manufacture.First,the distribution characteristics of the test data for the track error were verified using the skewness coefficient and kurtosis coefficient methods.According to the distribution characteristics,the azimuth track error was simulated by a two-scale model.The error of the long period and short amplitude was characterized as large-scale and described by a trigonometric function,while the short period and high amplitude error was characterized as small-scale and simulated by a fractal function.Based on the two-scale model,effect of the error on the pointing accuracy was deduced.Subsequently,the relationship between the root mean square(RMS)of the track error and the RMS of the pointing accuracy error of the telescope was deduced.Finally,the allowable RMS value of the track error was derived from the allowable pointing accuracy errors.To validate the effectiveness of the new design method,two typical radio telescopes(the Green Bank Telescope(GBT)and the Large Millimeter Telescope(LMT))were selected as experimental examples.Through comparison,the theoretical calculated values of the pointing accuracy of the telescope were consistent with the measured values,with a maximum error of less than 10%.展开更多
In this paper,an improved high-order model-free adaptive iterative control(IHOMFAILC)method for a class of nonlinear discrete-time systems is proposed based on the compact format dynamic linearization method.This meth...In this paper,an improved high-order model-free adaptive iterative control(IHOMFAILC)method for a class of nonlinear discrete-time systems is proposed based on the compact format dynamic linearization method.This method adds the differential of tracking error in the criteria function to compensate for the effect of the random disturbance.Meanwhile,a high-order estimation algorithmis used to estimate the value of pseudo partial derivative(PPD),that is,the current value of PPD is updated by that of previous iterations.Thus the rapid convergence of the maximumtracking error is not limited by the initial value of PPD.The convergence of the maximumtracking error is deduced in detail.This method can track the desired output with enhanced convergence and improved tracking performance.Two examples are used to verify the convergence and effectiveness of the proposed method.展开更多
To overcome nonlinear and 6-DOF(degrees of freedom)under-actuated problems for the attitude and position of quadrotor UAVs,an adaptive backstepping sliding mode method for flight attitude of quadrotor UAVs is proposed...To overcome nonlinear and 6-DOF(degrees of freedom)under-actuated problems for the attitude and position of quadrotor UAVs,an adaptive backstepping sliding mode method for flight attitude of quadrotor UAVs is proposed,in which an adaptive law is designed to online estimate the parameter variations and the upper bound of external disturbances and the assessments is utilized to compensate the backstepping sliding mode control.In addition,the tracking error of the design method is shown to asymptotically converge to zero by using Lyapunov theory.Finally,based on the numerical simulation of quadrotor UAVs using the setting parameters,the results show that the proposed control approach can stabilize the attitude and has hover flight capabilities under the parameter perturbations and external disturbances.展开更多
The operational principle, the impulse force and terminal guidance laws of terminal correction mortar projectiles（TCMP） are researched in this paper, by using the TCMP simulation program, key techniques such as the ...The operational principle, the impulse force and terminal guidance laws of terminal correction mortar projectiles（TCMP） are researched in this paper, by using the TCMP simulation program, key techniques such as the miss distance influenced by the acting point of impulse force, the impulse force value, the correction threshold, and the number of impulse rockets are researched in this paper. And the dual pulse control scheme is also studied. Simulation results indicate that the best acting point is near the center of gravity, sufficient correction resources are needed, the miss distance is insentive to the correction threshold, increasing the number of impulse rockets properly is beneficial to increase the hit precision, the velocity pursuit guidance law has less miss distance, the change of the attack angle is milder and the transient time becomes less in the dual impulse control scheme. These conclusions are important for choosing parameters and impulse correction schemes designed for TCMP.展开更多
The angular glint in the near field plays an important role on radar tracking errors. To predict it more efficiently for electrically large targets, a new method based on graphical electromagnetic computing （GRECO） ...The angular glint in the near field plays an important role on radar tracking errors. To predict it more efficiently for electrically large targets, a new method based on graphical electromagnetic computing （GRECO） is proposed. With the benefit of the graphic card, the GRECO prediction method is faster and more accurate than other methods. The proposed method at the first time considers the special case that the targets cannot be completely covered by radar beams, which makes the prediction of radar tracking errors more self-contained in practical circumstances. On the other hand, the process of the scattering center extraction is omitted, resulting in possible angular glint prediction in real time. Comparisons between the simulation results and the theoretical ones validate its correctness and value to academic research and engineering applications.展开更多
A modiΡed pseudo-noise（PN） code regeneration method is proposed to improve the clock tracking accuracy without impairing the code acquisition time performance.Thus,the method can meet the requirement of high accura...A modiΡed pseudo-noise（PN） code regeneration method is proposed to improve the clock tracking accuracy without impairing the code acquisition time performance.Thus,the method can meet the requirement of high accuracy ranging measurements in short time periods demanded by radio-science missions.The tracking error variance is derived by linear analysis.For some existing PN codes,which can be acquired rapidly,the tracking error variance performance of the proposed method is about 2.6 dB better than that of the JPL scheme（originally proposed by Jet Propulsion Laboratory）,and about 1.5 dB better than that of the traditional double loop scheme.展开更多
Batch processes have been increasingly used in the production of low volume and high value added products. Consequently, optimization control in batch processes is crucial in order to derive the maximum benefit. In th...Batch processes have been increasingly used in the production of low volume and high value added products. Consequently, optimization control in batch processes is crucial in order to derive the maximum benefit. In this paper, a run-to-run product quality control based on iterative learning optimization control is developed. Moreover, a rigorous theorem is proposed and proven in this paper, which states that the tracking error under the optimal iterative learning control （ILC） law can converge to zero. In this paper, a typical nonlinear batch continuous stirred tank reactor （CSTR） is considered, and the results show that the performance of trajectory tracking is gradually improved by the ILC.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant No. 60977005)
文摘The sub-land/sub-pit affects the characteristic of the tracking error signal which is generated by the conventional differential phase detection （DPD） method in the signal waveform modulation multi-level （SWML） read-only disc. To solve this problem, this paper proposes a new tracking error detection method using amplitude difference. Based on the diffraction theory, the amplitude difference is proportional to the tracking error and is feasible to be used for obtaining the off-track information. The experimental system of the amplitude difference detection method is developed. The experimental results show that the tracking error signal derived from the new method has better performance in uniformity and signal-to-noise ratio than that derived from the conventional DPD method in the SWML read-only disc.
文摘In order to solve problems in high dynamic environment, a frequency-locked loop （FLL） assisted phase-locked loop （PLL） is put forward for carrier tracking. On the basis of the analysis of discriminators, the total phase error of the tracking loop is analyzed and a general error expression is derived. By using linearization and Jaffe-Rechtin coefficients, the performance of a special first order FLL-assisted second order PLL is analyzed to get a closed expression. Analysis results and simula- tions show that there exist an optimal FLL loop bandwidth and a optimal PLL loop bandwidth which can make the phase jitter much less than that when the PLL is used alone.
文摘The aim of this study was to predict drivers＇ drowsy states with high risk of encountering a crash and prevent drivers from continuing to drive under such drowsy states with high risk of crash. While the participants were required to carry out a simulated driving task, EEG （Electro encephalography） （EEG-MPF and EEG-α/β）, ECG （Electrocradiogram） （RRV3）, t racking error, an d subjective rating on drowsiness were measured. On the basis of such measurements, an attempt was made to predict the point in time with high crash risk using Bayesian estimation of posterior probability of drowsiness, tracking error, and subjective drowsiness. As a result of applying the proposed method to the data of each participant, it was verified that the proposed method could predict the point in time with high crash risk before the point in time of crash.
基金funded by the National Natural Science Foundation of China(Grant No.U19A2072)the Provincial Department of Education Postgraduate Scientific Research Innovation Project of Hunan Province of China(Grant No.QL20210007)the Ministerial Level Postgraduate Funding Project of China(Grant No.JY2021A007).
文摘Small tracking error correction for electro-optical systems is essential to improve the tracking precision of future mechanical and defense technology.Aerial threats,such as“low,slow,and small(LSS)”moving targets,pose increasing challenges to society.The core goal of this work is to address the issues,such as small tracking error correction and aiming control,of electro-optical detection systems by using mechatronics drive modeling,composite velocity–image stability control,and improved interpolation filter design.A tracking controller delay prediction method for moving targets is proposed based on the Euler transformation model of a two-axis,two-gimbal cantilever beam coaxial configuration.Small tracking error formation is analyzed in detail to reveal the scientific mechanism of composite control between the tracking controller’s feedback and the motor’s velocity–stability loop.An improved segmental interpolation filtering algorithm is established by combining line of sight(LOS)position correction and multivariable typical tracking fault diagnosis.Then,a platform with 2 degrees of freedom is used to test the system.An LSS moving target shooting object with a tracking distance of S=100 m,target board area of A=1 m^(2),and target linear velocity of v=5 m/s is simulated.Results show that the optimal method’s distribution probability of the tracking error in a circle with a radius of 1 mrad is 66.7%,and that of the traditional method is 41.6%.Compared with the LOS shooting accuracy of the traditional method,the LOS shooting accuracy of the optimized method is improved by 37.6%.
基金supported by the Youth Innovation Promotion Association of the Chinese Academy of Sciences program(No.2021417).The critical discussions with colleagues in the accelerator physics and hardware groups at IMP are also greatly appreciated.
文摘Purpose The Space Environment Simulation and Research Infrastructure(SESRI)is a cluster of accelerators designed to simulate the cosmic radiation environment by generating particles of various types and energies.Among these accelerators,a synchrotron in the 300 MeV proton and heavy ion accelerator complex utilizes a multiturn injection scheme with four bump magnets to accumulate proton and heavy ion beams effectively.However,the bump magnetic field experiences a rapid drop rate of up to 1000 T/s,inevitably leading to a deviation(field tracking error)from the ideal magnetic field.The injection efficiency and particle distribution are significantly affected by this field tracking error,as evaluated by the ACCSIM code.Method During the device testing stage,the sources of field tracking errors were identified by analysis of the bump power supplies and the field of the magnets.Mitigation techniques were then implemented to reduce the field tracking error from[Math Processing Error]to[Math Processing Error]throughout the entire power supply,transmission cable,and magnet chain.Results Moreover,the successful injection and accumulation of beams during the operational phase of the synchrotron confirmed the effectiveness of the proposed mitigation methods.Additionally,a magnetic field measurement system was developed to monitor the magnetic field tracking error online.Conclusion The combination of the field tracking error mitigation methods and the measurement system provides valuable guidance for optimizing the magnetic fields with rapid drop rates.
基金partially supported by a National Key Basic Research Project of China under Grant No.2011CB302400the Natural Science Foundation of China under Grant No.60821002
文摘In this paper,the problem of time optimal feedrate generation under confined feedrate,axis accelerations,and axis tracking errors is considered.The main contribution is to reduce the tracking error constraint to constraints about the axis velocities and accelerations,when the tracking error satisfies a second order linear ordinary differential equation.Based on this simplification on the tracking error,the original feedrate generation problem is reduced to a new form which can be efficiently solved with linear programming algorithms.Simulation results are used to validate the methods.
基金partially supported by a National Key Basic Research Project of Chinaa USA NSF grant CCR-0201253the Foundation of UPC for the Author of National Excellent Doctoral Dissertation under Grant No.120501A
文摘In this paper,a method of reducing the tracking error in CNC machining is proposed.The structured neural network is used to approximate the discontinuous friction in CNC machining,which has jump points and uncertainties.With the estimated nonlinear friction function,the reshaped trajectory can be computed from the desired one by solving a second order ODE such that when the reshaped trajectory is fed into the CNC controller,the output is the desired trajectory and the tracking error is eliminated in certain sense.The proposed reshape method is also shown to be robust with respect to certain parameters of the dynamic system.
基金National Natural Science Foundation of China (No. 50475038).
文摘Laser tracking system （LTS） is an advanced device for large size 3D coordinates measuring with the advantages of broad range, high speed and high accuracy. However, its measuring accuracy is highly dominated by the geometric errors of the tracking mirror mechanism. Proper calibration of LTS is essential prior to the use of it for metrology. A kinematics model that describes not only the motion but also the geometric variations of LTS is developed. Through error analysis of the proposed model, it is claimed that gimbals axis misalignments and tracking mirror center off-set are the key contributors to measuring errors of LTS. A self-calibration method is presented of calibrating LTS with planar constraints. Various calibration strategies utilizing single-plane and multiple-plane constraints are proposed for different situations. For each calibration strategy, issues about the error parameter estimation of LTS are exploded to find out in which conditions these parameters can be uniquely estimated. Moreover, these conditions reveal the applicability of the planar constraints to LTS self-calibration. Intensive studies have been made to check validity of the theoretical results. The results show that the measuring accuracy of LTS has increased by 5 times since this technique for calibration is used.
基金Supported by National natural Sciences Foundation of China(Y2113A005C)
文摘The Rapid Cycling Synchrotron （RCS） is a key component of the China Spallation Neutron Source （CSNS）. For this type of high intensity proton synchrotron, the chromaticity, space charge effects, and magnetic field tracking errors between the quadrupoles and the dipoles can induce beta function distortion and tune shift, and induce resonances. In this paper, the combined effects of chromaticity, magnetic field tracking errors and space charge on beam dynamics at CSNS/RCS are studied systemically. 3-D simulations with different magnetic field tracking errors are performed by using the code ORBIT, and the simulation results are compared with the case without tracking errors.
文摘Radar leveling system is the key equipment for improving the radar mobility and survival capability. A combined quantitative feedback theory (QFT) controller is designed for the radar truck leveling simulator in this paper, which suffers from strong nonlinearities and system parameter uncertainties. QFT can reduce the plant uncertainties and stabilize the system, but it fails to obtain high-precision tracking. This drawback can be solved by a robust QFT control scheme based on zero phase error tracking control (ZPETC) compensation. The combined controller not only possesses high robustness, but greatly improves the system performance. To verify the effiectiveness and the potential of the proposed controller, a series of experiments have been carried out. Experimental results have demonstrated its robustness against a large range of parameters variation and high tracking precision performance, as well as its capability of restraining the load coupling among channels. The combined QFT controller can drive the radar truck leveling platform accurately, quickly and stably.
文摘To track the narrow butt welding seams in container manufacture, a visual tracking system based on smart camera is proposed in this paper. A smart camera is used as the sensor to detect the welding seam. The feature extraction algorithm is designed with the consideration of the characteristics of the smart caraera, which is used to compute the error between the welding torch and the welding seam. Visual control system based on image is preseated, which employs a programmable controller to control a stepper motor to eliminate the tracking error detected by the smart camera. Experiments are conducted to demonstrate the effectiveness of the vision system.
基金supported by the Science Foundation of the Education Office of Gansu Province of Chinaunder Grant No.0914-01
文摘The contour error was analyzed based on CNC multi-axis motion control, the contour error model was obtained focused on beeline and different radius of curvature and common contour of curve, for a CNC biaxial motion control system and the mechanism of producing contour error and the relationship between tracking error and contour error were presented. The theoretical and practical significance of modeling error and controlling error in motion control systems was carried out.
基金Supported by the National Natural Science Foundation of China(No.41474027)the National Defense Basic Science Project(JCKY2016110B004)
文摘Vector tracking changes the classical structure of receivers. Combining signal tracking and navigation solution,vector tracking can realize powerful processing capabilities by the fusion technique of receiving channel and feedback correction. In this paper,we try to break through the complicated details of numerical analysis,consider the overall influencing factors of the residual in observed data,and use the intrinsic link between a conventional receiver and a vector receiver. A simple method for performance analysis of the vector tracking algorithm is proposed. Kalman filter has the same steady performance with the classic digital lock loop through the analysis of the relation between gain and band width. The theoretical analysis by the least squares model shows that the reduction of range error is the basis for the superior performance realized by vector tracking. Thus,the bounds of its performance enhancement under weak signal and highly dynamic conditions can be deduced. Simulation results verify the effectiveness of the analysis presented here.
基金financial support from the National Natural Science Foundation of China (51775402 and U1931139)
文摘The Qi Tai Telescope(QTT),which has a 110 m aperture,is planned to be the largest scale steerable tele-scope in the world.Ideally,the telescope’s repeated pointing accuracy error should be less than 2.5 arc seconds(arcsec);thus,the telescope structure must satisfy ultra-high precision requirements.In this pur-suit,the present research envisages a reverse-design method for the track surface to reduce the difficulty of the telescope’s design and manufacture.First,the distribution characteristics of the test data for the track error were verified using the skewness coefficient and kurtosis coefficient methods.According to the distribution characteristics,the azimuth track error was simulated by a two-scale model.The error of the long period and short amplitude was characterized as large-scale and described by a trigonometric function,while the short period and high amplitude error was characterized as small-scale and simulated by a fractal function.Based on the two-scale model,effect of the error on the pointing accuracy was deduced.Subsequently,the relationship between the root mean square(RMS)of the track error and the RMS of the pointing accuracy error of the telescope was deduced.Finally,the allowable RMS value of the track error was derived from the allowable pointing accuracy errors.To validate the effectiveness of the new design method,two typical radio telescopes(the Green Bank Telescope(GBT)and the Large Millimeter Telescope(LMT))were selected as experimental examples.Through comparison,the theoretical calculated values of the pointing accuracy of the telescope were consistent with the measured values,with a maximum error of less than 10%.
文摘In this paper,an improved high-order model-free adaptive iterative control(IHOMFAILC)method for a class of nonlinear discrete-time systems is proposed based on the compact format dynamic linearization method.This method adds the differential of tracking error in the criteria function to compensate for the effect of the random disturbance.Meanwhile,a high-order estimation algorithmis used to estimate the value of pseudo partial derivative(PPD),that is,the current value of PPD is updated by that of previous iterations.Thus the rapid convergence of the maximumtracking error is not limited by the initial value of PPD.The convergence of the maximumtracking error is deduced in detail.This method can track the desired output with enhanced convergence and improved tracking performance.Two examples are used to verify the convergence and effectiveness of the proposed method.
基金Project(61203021)supported by the National Natural Science Foundation of ChinaProject(2011216011)supported by the Scientific and Technological Project of Liaoning Province,China+1 种基金Project(2013020024)supported by the Natural Science Foundation of Liaoning Province,ChinaProjects(LJQ2015061,LR2015034)supported by the Program for Liaoning Excellent Talents in University,China
文摘To overcome nonlinear and 6-DOF(degrees of freedom)under-actuated problems for the attitude and position of quadrotor UAVs,an adaptive backstepping sliding mode method for flight attitude of quadrotor UAVs is proposed,in which an adaptive law is designed to online estimate the parameter variations and the upper bound of external disturbances and the assessments is utilized to compensate the backstepping sliding mode control.In addition,the tracking error of the design method is shown to asymptotically converge to zero by using Lyapunov theory.Finally,based on the numerical simulation of quadrotor UAVs using the setting parameters,the results show that the proposed control approach can stabilize the attitude and has hover flight capabilities under the parameter perturbations and external disturbances.
基金Sponsored by the Ministerial Level Advanced Research Foundation (40406030101)
文摘The operational principle, the impulse force and terminal guidance laws of terminal correction mortar projectiles（TCMP） are researched in this paper, by using the TCMP simulation program, key techniques such as the miss distance influenced by the acting point of impulse force, the impulse force value, the correction threshold, and the number of impulse rockets are researched in this paper. And the dual pulse control scheme is also studied. Simulation results indicate that the best acting point is near the center of gravity, sufficient correction resources are needed, the miss distance is insentive to the correction threshold, increasing the number of impulse rockets properly is beneficial to increase the hit precision, the velocity pursuit guidance law has less miss distance, the change of the attack angle is milder and the transient time becomes less in the dual impulse control scheme. These conclusions are important for choosing parameters and impulse correction schemes designed for TCMP.
基金supported by the National Natural Science Foundation of China (60871069)
文摘The angular glint in the near field plays an important role on radar tracking errors. To predict it more efficiently for electrically large targets, a new method based on graphical electromagnetic computing （GRECO） is proposed. With the benefit of the graphic card, the GRECO prediction method is faster and more accurate than other methods. The proposed method at the first time considers the special case that the targets cannot be completely covered by radar beams, which makes the prediction of radar tracking errors more self-contained in practical circumstances. On the other hand, the process of the scattering center extraction is omitted, resulting in possible angular glint prediction in real time. Comparisons between the simulation results and the theoretical ones validate its correctness and value to academic research and engineering applications.
基金supported by the National Natural Science Foundation of China (60904090)the Postdoctoral Science Foundation of China(20080431306)the Special Postdoctoral Science Foundation of China (20081458)
文摘A modiΡed pseudo-noise（PN） code regeneration method is proposed to improve the clock tracking accuracy without impairing the code acquisition time performance.Thus,the method can meet the requirement of high accuracy ranging measurements in short time periods demanded by radio-science missions.The tracking error variance is derived by linear analysis.For some existing PN codes,which can be acquired rapidly,the tracking error variance performance of the proposed method is about 2.6 dB better than that of the JPL scheme（originally proposed by Jet Propulsion Laboratory）,and about 1.5 dB better than that of the traditional double loop scheme.
基金supported by the Science Foundation of Shanghai Municipal Education Commission (Grant No.09Y208)the Science Foundation of Science and Technology Commission of Shanghai Municipality (Grant Nos.08DZ2272400, 09DZ2273400)the "11th Five-Year Plan" 211 Construction Project of Shanghai University
文摘Batch processes have been increasingly used in the production of low volume and high value added products. Consequently, optimization control in batch processes is crucial in order to derive the maximum benefit. In this paper, a run-to-run product quality control based on iterative learning optimization control is developed. Moreover, a rigorous theorem is proposed and proven in this paper, which states that the tracking error under the optimal iterative learning control （ILC） law can converge to zero. In this paper, a typical nonlinear batch continuous stirred tank reactor （CSTR） is considered, and the results show that the performance of trajectory tracking is gradually improved by the ILC.
