Using metallographic observation and mechanical measurement,the microstructure and mechanical properties of GH4169G alloy has been investigated.The effect of the phosphorus,boron trace elements on mechanical propertie...Using metallographic observation and mechanical measurement,the microstructure and mechanical properties of GH4169G alloy has been investigated.The effect of the phosphorus,boron trace elements on mechanical properties of the GH4169G alloy are compared and analyzed.The results showed that the hot-workability of the GH4169G alloy is very good.The stress ruptures properties of GH4169G alloy is over 3 times than the traditional GH4169 alloy.展开更多
Crack detection in an aerospace turbine disk is essential for aircraft-quality detection.With the unique circular stepped structure and superalloy material properties of aerospace turbine disk,it is difficult for the ...Crack detection in an aerospace turbine disk is essential for aircraft-quality detection.With the unique circular stepped structure and superalloy material properties of aerospace turbine disk,it is difficult for the traditional ultrasonic testing method to perform efficient and accurate testing.In this study,ultrasound phased array detection technology was applied to the non-destructive testing of aviation turbine disks:(i)A phased array ultrasonic c-scan device for detecting aerospace turbine disk cracks(PAUDA)was developed which consists of phased array ultrasonic,transducers,a computer,a displacement encoder,and a rotating scanner;(ii)The influence of the detection parameters include frequency,wave-type,and elements number of the ultrasonic phased array probe on the detection results on the near-surface and the far surface of the aerospace turbine disk is analyzed;(iii)Specimens with flat-bottom-hole(FBH)defects were scanned by the developed PAUDA and the results were analyzed and compared with the conventional single probe ultrasonic water immersion testing.The experiment shows that by using the ultrasonic phased array c-scan to scan the turbine disk the accuracy of the detection can be significantly improved which is of greater accuracy and higher efficiency than traditional immersion testing.展开更多
Nickel-base superalloys are high performance materials subject to severe operating conditions in the high temperature turbine section of gas turbine engines.Turbine blades in modern engines are fabricated from Ni-base...Nickel-base superalloys are high performance materials subject to severe operating conditions in the high temperature turbine section of gas turbine engines.Turbine blades in modern engines are fabricated from Ni-base alloy single crystals which are strengthened by ordered g’ precipitates.Turbine disks are made from polycrystal line Ni-base alloys because these components have higher strength requirements(due to higher stresses).By increasing the upper temperature limit for the next generation of disk materials,the aviation industry will see significant environmental as well as cost benefits. Researchers in the High Temperature Materials Center of the National Institute of Materials Science of Japan have recently completed their work on a new kind of disk alloys.The new disk alloys,a kind of nickel-coble-base superalloys processed by a normal cast and wrought(C & W) route,can withstand temperatures in excess of 725 degree centigrade,a 50-degree increase over C&W disks currently in operation. In this presentation,the author shows the design idea,workability and properties of these Ni-Co-base superalloys. Furthermore,the evaluation of the processing and microstructure on a full-scale processing of Ni-Co-base superalloy turbine disk are described,which demonstrated the advantages and possibility of the Ni-Co-base disc alloys at the component level.展开更多
Modern gas turbines work under demanding high temperatures, high pressures, andhigh rotational speeds. In order to ensure durable and reliable operation, effective cooling mea-sures must be applied to the high-tempera...Modern gas turbines work under demanding high temperatures, high pressures, andhigh rotational speeds. In order to ensure durable and reliable operation, effective cooling mea-sures must be applied to the high-temperature rotating components, including turbine bladesand turbine disks. Cooling technology, however, is one of the most challenging problems inthis field. The present work reviews the current state of cooling technology research, at boththe fundamental science and engineering implementation levels, including modeling and simu-lation, experiments and diagnostics, and cooling technologies for blades and disks. In numericalsimulation, the RANS approach remains the most commonly used technique for flow-dynamicsand heat-transfer simulations. Much attention has been given to the development of improvedturbulence modeling for flows under rotation. For measurement and diagnostics, advancedinstrumentation and rotating-flow test facilities have been developed and valuable experimentaldata obtained. Detailed velocity and temperature distributions in rotating boundary layers havebeen obtained at scales sufficient to resolve various underlying mechanisms. Both isothermaland non-isothermal conditions have been considered, and the effects of Coriolis and buoyancyforces on flow evolution and heat transfer quantitatively identified. Cooling technologies havebeen improved by optimizing cooling passage dsigns, especially for curved configurations un-der rotation. Novel methods such as lamellar cooling and micro-scale cooling were proposed,and their effectiveness evaluated. For disk/cavity cooling, efforts were mainly focused on rotor-stator systems, with special attention given to the position of air injection into disks.展开更多
文摘Using metallographic observation and mechanical measurement,the microstructure and mechanical properties of GH4169G alloy has been investigated.The effect of the phosphorus,boron trace elements on mechanical properties of the GH4169G alloy are compared and analyzed.The results showed that the hot-workability of the GH4169G alloy is very good.The stress ruptures properties of GH4169G alloy is over 3 times than the traditional GH4169 alloy.
基金This work was funded by the National Natural Science Foundation of China[Grant Nos.11664027,11374134]The National Natural Science Foundation of Jiangxi Province[Grant No.20161BAB216101]+1 种基金Key Laboratory of Non-Destructive Testing and Monitoring Technology for High-Speed Transport Facilities of the Ministry of Industry and Information Technology,Nanjing University of Aeronautics and AstronauticsThe Key Laboratory of Nondestructive Testing of Ministry of Education Nanchang Hang Kong University,Nanchang,China.
文摘Crack detection in an aerospace turbine disk is essential for aircraft-quality detection.With the unique circular stepped structure and superalloy material properties of aerospace turbine disk,it is difficult for the traditional ultrasonic testing method to perform efficient and accurate testing.In this study,ultrasound phased array detection technology was applied to the non-destructive testing of aviation turbine disks:(i)A phased array ultrasonic c-scan device for detecting aerospace turbine disk cracks(PAUDA)was developed which consists of phased array ultrasonic,transducers,a computer,a displacement encoder,and a rotating scanner;(ii)The influence of the detection parameters include frequency,wave-type,and elements number of the ultrasonic phased array probe on the detection results on the near-surface and the far surface of the aerospace turbine disk is analyzed;(iii)Specimens with flat-bottom-hole(FBH)defects were scanned by the developed PAUDA and the results were analyzed and compared with the conventional single probe ultrasonic water immersion testing.The experiment shows that by using the ultrasonic phased array c-scan to scan the turbine disk the accuracy of the detection can be significantly improved which is of greater accuracy and higher efficiency than traditional immersion testing.
文摘Nickel-base superalloys are high performance materials subject to severe operating conditions in the high temperature turbine section of gas turbine engines.Turbine blades in modern engines are fabricated from Ni-base alloy single crystals which are strengthened by ordered g’ precipitates.Turbine disks are made from polycrystal line Ni-base alloys because these components have higher strength requirements(due to higher stresses).By increasing the upper temperature limit for the next generation of disk materials,the aviation industry will see significant environmental as well as cost benefits. Researchers in the High Temperature Materials Center of the National Institute of Materials Science of Japan have recently completed their work on a new kind of disk alloys.The new disk alloys,a kind of nickel-coble-base superalloys processed by a normal cast and wrought(C & W) route,can withstand temperatures in excess of 725 degree centigrade,a 50-degree increase over C&W disks currently in operation. In this presentation,the author shows the design idea,workability and properties of these Ni-Co-base superalloys. Furthermore,the evaluation of the processing and microstructure on a full-scale processing of Ni-Co-base superalloy turbine disk are described,which demonstrated the advantages and possibility of the Ni-Co-base disc alloys at the component level.
文摘Modern gas turbines work under demanding high temperatures, high pressures, andhigh rotational speeds. In order to ensure durable and reliable operation, effective cooling mea-sures must be applied to the high-temperature rotating components, including turbine bladesand turbine disks. Cooling technology, however, is one of the most challenging problems inthis field. The present work reviews the current state of cooling technology research, at boththe fundamental science and engineering implementation levels, including modeling and simu-lation, experiments and diagnostics, and cooling technologies for blades and disks. In numericalsimulation, the RANS approach remains the most commonly used technique for flow-dynamicsand heat-transfer simulations. Much attention has been given to the development of improvedturbulence modeling for flows under rotation. For measurement and diagnostics, advancedinstrumentation and rotating-flow test facilities have been developed and valuable experimentaldata obtained. Detailed velocity and temperature distributions in rotating boundary layers havebeen obtained at scales sufficient to resolve various underlying mechanisms. Both isothermaland non-isothermal conditions have been considered, and the effects of Coriolis and buoyancyforces on flow evolution and heat transfer quantitatively identified. Cooling technologies havebeen improved by optimizing cooling passage dsigns, especially for curved configurations un-der rotation. Novel methods such as lamellar cooling and micro-scale cooling were proposed,and their effectiveness evaluated. For disk/cavity cooling, efforts were mainly focused on rotor-stator systems, with special attention given to the position of air injection into disks.
