To investigate the correlation between structure characteristics and wear resistance of CO2 corrosion product scales at high temperature and high pressure, an autoclave was used to prepare CO2 corrosion product scales...To investigate the correlation between structure characteristics and wear resistance of CO2 corrosion product scales at high temperature and high pressure, an autoclave was used to prepare CO2 corrosion product scales on N80 steel in carbon dioxide corrosion environment. The correlation between wear resistance of the scales and many other factors, such as temperature, pressure, morphology, structure, velocity of fluid medium, sand grain size, and so on, was comparatively analyzed by a self assembled wear device, and the scale morphologies before or after being worn were observed by scanning electron microscope （SEM）. And then the surface grain size and thickness of scale were measured. The results showed that the cross-section of the corrosion scale was of a double-layer structure, the outer layer of which was composed of regular crystals, whereas the inner layer was a thin scale of fine grains. The outer grain size and thickness of scale varied with temperature, and the initial wear loss was consistent with the surface grain size; at the same time, the total wear loss corresponded to the thickness of scale. Compared to wear resist- ance in different depths of the scale, it was found that the structure of scale was a double-layer structure in cross-section, and the wear resistance of inner layer was better than that of the outer layer; the closer the scale to the matrix, the greater was the wear resistance of scale; and the larger the size or the higher the rotary speed of solid grain in multiphase flowing medium, the more was the wear loss of scale.展开更多
Wear resistances of CO2 corrosion product films formed on P110 carbon steel at different CO2 partial pressures were investigated in water sand two-phase flow by weight loss method, and the microstructures and composit...Wear resistances of CO2 corrosion product films formed on P110 carbon steel at different CO2 partial pressures were investigated in water sand two-phase flow by weight loss method, and the microstructures and compositions of corrosion product films were analyzed by scanning electron microscope(SEM) and X-ray diffraction(XRD), respectively. The results showed that the wear rate of CO2 corrosion product films increased until a maximum and then decreased with the increasing of the film-forming pressure, and the maximum occurred at 2 MPa. However, the maximal corrosion rate and the loose and porous CO2 corrosion product films were obtained at 4 MPa. And the wear rate decreased and then went to be flat with increasing test time. Furthermore, the microstructures and compositions of corrosion product films and the impact and wear of sand particles played an important role on wear resistances. In addition, the wear rate and corrosion rate were fitted by cubic polynomial, respectively, which were well in accordance with the measured results.展开更多
To reuse roller waste as a raw material of high performance green ceramic balls, three kinds of white alumina ceramic balls whose wear resistance were 2-3 times of the best high alumina ceramic ball with 90% Al2O3 wer...To reuse roller waste as a raw material of high performance green ceramic balls, three kinds of white alumina ceramic balls whose wear resistance were 2-3 times of the best high alumina ceramic ball with 90% Al2O3 were prepared, and the Al2O3 content of the prepared balls was 75%. It is found that the effect of calcia and magnesia on the wear resistance of ceramic balls is contrast to the accepted one： the wear rate of the ceramic balls prepared in CaO-Al2O3-SiO2 system is the lowest and the wear rate of the ceramic balls prepared in MgO-Al2O3-SiO2 is the highest. The main crystal phase of the ceramic ball is mullite and corundum. The ceramic ball granular is uniform and fine with 4-5 μm average size. The pore diameter is about 2 μm. The wear way of the ceramic balls is mainly transcrystalline fracture.展开更多
基金Item Sponsored by National Natural Science Foundation of China (50231020) , National Basic Research Programof China(G1999065004) ,2001'Key Laboratory Opening Fund of Corrosion and Protection of Tabular Goods Research Center of ChinaNational Petroleum Corporation (ZYT-01070)
文摘To investigate the correlation between structure characteristics and wear resistance of CO2 corrosion product scales at high temperature and high pressure, an autoclave was used to prepare CO2 corrosion product scales on N80 steel in carbon dioxide corrosion environment. The correlation between wear resistance of the scales and many other factors, such as temperature, pressure, morphology, structure, velocity of fluid medium, sand grain size, and so on, was comparatively analyzed by a self assembled wear device, and the scale morphologies before or after being worn were observed by scanning electron microscope （SEM）. And then the surface grain size and thickness of scale were measured. The results showed that the cross-section of the corrosion scale was of a double-layer structure, the outer layer of which was composed of regular crystals, whereas the inner layer was a thin scale of fine grains. The outer grain size and thickness of scale varied with temperature, and the initial wear loss was consistent with the surface grain size; at the same time, the total wear loss corresponded to the thickness of scale. Compared to wear resist- ance in different depths of the scale, it was found that the structure of scale was a double-layer structure in cross-section, and the wear resistance of inner layer was better than that of the outer layer; the closer the scale to the matrix, the greater was the wear resistance of scale; and the larger the size or the higher the rotary speed of solid grain in multiphase flowing medium, the more was the wear loss of scale.
基金Funded by China Postdoctoral Science Foundation(No.2014M552477)Natural Science Basic Research Plan in Shaanxi Province of China(Nos.2014JQ2056 and 2014JQ6219)Key Laboratory Scientific Research Program of Shaanxi Provincial Education Department(No.14JS086)
文摘Wear resistances of CO2 corrosion product films formed on P110 carbon steel at different CO2 partial pressures were investigated in water sand two-phase flow by weight loss method, and the microstructures and compositions of corrosion product films were analyzed by scanning electron microscope(SEM) and X-ray diffraction(XRD), respectively. The results showed that the wear rate of CO2 corrosion product films increased until a maximum and then decreased with the increasing of the film-forming pressure, and the maximum occurred at 2 MPa. However, the maximal corrosion rate and the loose and porous CO2 corrosion product films were obtained at 4 MPa. And the wear rate decreased and then went to be flat with increasing test time. Furthermore, the microstructures and compositions of corrosion product films and the impact and wear of sand particles played an important role on wear resistances. In addition, the wear rate and corrosion rate were fitted by cubic polynomial, respectively, which were well in accordance with the measured results.
基金the National Natural Science Fundation of China(No.50272016),Guangxi 2003 Degree Authorzation Office academic Construction Fun,and Natural Science Fund of Guangxi Education Department(No.[2004]4)
文摘To reuse roller waste as a raw material of high performance green ceramic balls, three kinds of white alumina ceramic balls whose wear resistance were 2-3 times of the best high alumina ceramic ball with 90% Al2O3 were prepared, and the Al2O3 content of the prepared balls was 75%. It is found that the effect of calcia and magnesia on the wear resistance of ceramic balls is contrast to the accepted one： the wear rate of the ceramic balls prepared in CaO-Al2O3-SiO2 system is the lowest and the wear rate of the ceramic balls prepared in MgO-Al2O3-SiO2 is the highest. The main crystal phase of the ceramic ball is mullite and corundum. The ceramic ball granular is uniform and fine with 4-5 μm average size. The pore diameter is about 2 μm. The wear way of the ceramic balls is mainly transcrystalline fracture.
