Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. I...Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. In service environments, CMCs exhibit complex damage mechanisms and failure modes, which are affected by constituent materials, meso-architecture and inhere defects. In this paper, the in-plane tensile mechanical behavior of a plain-woven SiCf/SiC composite at room and elevated temperatures was investigated, and the factors affecting the tensile strength of the material were discussed in depth. The results show that the tensile modulus and strength of SiCf/SiC composites at high temperature are lower, but the fracture strain increases and the toughness of the composites is enhanced;the stitching holes significantly weaken the tensile strength of the material, resulting in the material is easy to break at the cross-section with stitching holes.展开更多
In the study,it is proposed that a coordinate-parametric matrix model is performed to a square-conjoint pattern of cross woven(SCPCW)in the bamboo mat.The patterns of SCPCW are firstly detected according to the perspe...In the study,it is proposed that a coordinate-parametric matrix model is performed to a square-conjoint pattern of cross woven(SCPCW)in the bamboo mat.The patterns of SCPCW are firstly detected according to the perspective of configuration,which is divided into the basic-monomer shape and the basic combination shape.Secondly,the compositions of design patterns in SCPCW are analyzed to attain the trend of curve shape.Based on the coordinate-parametric matrix model,the specimens of SCPCW are subsequently accomplished to elaborate the woven logic of bamboo mats.The digital innovation of SCPCW,defined by a mathematical resolution,is implemented by the software of Grasshopper(GH),which plays a crucial role in capturing image information by the Image Sampler component.Successively,the weaving logic of coordinated matrix is referred to apply in the computing component of Grasshopper software.Finally,the computer simulation could demonstrate that the coordinate-parametric matrix model of SCPCWwould be realized to analyze the micro-weaving structure and overall weaving effect in the bamboo mat.展开更多
With the wide use of three-dimensional woven spacer composites(3DWSCs),the market expects greater mechanical properties from this material.By changing the weft fastening method of the traditional I-shape pile yarns,we...With the wide use of three-dimensional woven spacer composites(3DWSCs),the market expects greater mechanical properties from this material.By changing the weft fastening method of the traditional I-shape pile yarns,we designed three-dimensional woven spacer fabrics(3DWSFs)and 3DWSCs with the weft V-shape to improve the compression performance of traditional 3DWSFs.The effects of weft binding structures,V-pile densities,and V-shaped angle were investigated in this paper.It is found that the compression resistance of 3DWSFs with the weft V-shape is improved compared to that with the weft I-shape,the fabric height recovery rate is as high as 95.7%,and the average elastic recovery rate is 59.39%.When the interlayer pile yarn density is the same,the weft V-shaped and weft I-shaped 3DWSCs have similar flatwise pressure and edgewise pressure performance.The compression properties of the composite improve as the density of the V-pile yarns increases.The flatwise compression load decreases as the V-shaped angle decreases.When the V-shaped angle is 28°and 42°,the latitudinal V-shaped 3DWSCs perform exceptionally well in terms of anti-compression cushioning.The V-shaped weft binding method offers a novel approach to structural design of 3DWSCs.展开更多
In this paper,using Parseval frames we generalize Sun’s results to g-frames in Hilbert C^(*)-modules.Moreover,for g-frames in Hilbert spaces,we present some characterizations in terms of a family of frames,not only f...In this paper,using Parseval frames we generalize Sun’s results to g-frames in Hilbert C^(*)-modules.Moreover,for g-frames in Hilbert spaces,we present some characterizations in terms of a family of frames,not only for orthonormal bases.Also,we have a note about a comment and a relation in the proof of Proposition 5.3 in[D.Li et al.,On weaving g-frames for Hilbert spaces,Complex Analysis and Operator Theory,2020].Finally,we have some results for g-Riesz bases,woven and P-woven g-frames.展开更多
The curriculum“Woven Fabric Structure Design and Application”is the core curriculum of textile majors in higher vocational colleges,which plays a very important role in the cultivation of students’vocational abilit...The curriculum“Woven Fabric Structure Design and Application”is the core curriculum of textile majors in higher vocational colleges,which plays a very important role in the cultivation of students’vocational ability and professional quality.The curriculum reform of“Woven Fabric Structure Design and Application”through the deep cooperation of industry-college partnerships,the comprehensive analysis of the major training objectives and graduation requirements,the redesign of the curriculum teaching content,the improvement of the teaching method and the examination method,has achieved good results.展开更多
A micro mechanical model is carried out to predict micro stresses and macro elastic properties of 3-D woven composites. A unit cell is composed of two phases. One is fiber yarn and the other is resin or fiber yarn in ...A micro mechanical model is carried out to predict micro stresses and macro elastic properties of 3-D woven composites. A unit cell is composed of two phases. One is fiber yarn and the other is resin or fiber yarn in transverse. The additional shearing introduced by bending of fiber yarn is considered. The method to determine the microstructure is also discussed. This model is applied to the analysis of a 3-D woven graphite/epoxy composite. Micro stresses of the cell are studied, and then macro modulus is obtained by employing the average method. The predictions agree well with experimental results.展开更多
The outbreak of coronavirus has led to an increase in the demand for facemasks globally. Unavailability of appropriate polypropylene non-woven fabrics face masks as a result of inadequate supply to satisfy the growing...The outbreak of coronavirus has led to an increase in the demand for facemasks globally. Unavailability of appropriate polypropylene non-woven fabrics face masks as a result of inadequate supply to satisfy the growing population has brought about the manufacturing of locally fabrics masks to augment or substitute standard medical class facemasks. The study aims at analyzing airflow of these locally manufactured fabrics to determine possible means of transmitting the virus as well as establish comfort of the user of these masks. Standard polypropylene non-woven, woven and knitted fabrics were considered for the study. Air permeability test was conducted on these fabrics using Frazier Air permeability tester. Depending on the property significant variation in the textile fabrics, polypropylene non-woven is widely accepted for facial masks. Nevertheless, this study illustrates that woven and knitted fabrics have more open structures, which allow a high rate of air penetration and so may require two or three layers to prevent antimicrobial or antiviral potential.展开更多
In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It...In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It has important value to study on the relationship between tribological performances of the liner and the friction heat. Unforttmately, up to now, published work on this relationship is quite scarce. Therefore, the effect of friction heat on the tribological performances of the liner was investigated in the present work. The tribological behaviors of the liner were evaluated by using the high temperature end surface wear tester. Scanning electron microscopy （SEM） was utilized to examine the morphologies of worn surfaces of the liner and study the failure modes. Differential scanning calorimetry （DSC） measurement and X-ray diffraction （XRD） analysis were performed to study the behaviors of the wear debris. The temperature rise on the worn surface was calculated according to classical models. SEM observation shows that the dominating wear mechanism for the liner is mainly affected by friction shear force, contact pressure and friction heat. Higher fusion heat for the wear debris than that for the pure polytetrafluroethylene （PTFE） indicates that the PTFE is the main portion of the wear debris, and, the PTFE in the wear debris shows a higher crystallisation degree owing to the effects of friction shear force and the friction heat. Combining the calculated temperature rise results with the wear rate of the liner, it can be concluded that the effects of temperature rise o n the tribological performances of the liner become more obvious when the temperature rise exceeds the glass transition temperature （Tg） of the PTFE. The wear resistance of the liner deteriorates dramatically when the temperature rise approaches to the melting point （Ton） of the PTFE. The tribological performances of the liner can be improved when the temperature rise exceeds Tg but is far lower than Ton- The present study on the relationship between the temperature rise and the tribological performances of the liner may provide the basis for further understanding of the wear mechanisms of the liner as well as the relationship between the formation of the PTFE transfer film and the friction heat during the dry-sliding of the Finer.展开更多
In order to improve the wettability and biocompatibility of the poly （butylene terephthalate） non-woven （PBTNW）, the method of surface modification is used to graft copolymerization of chitosan （CS） onto the PBT...In order to improve the wettability and biocompatibility of the poly （butylene terephthalate） non-woven （PBTNW）, the method of surface modification is used to graft copolymerization of chitosan （CS） onto the PBTNW under alkylpolyglycoside （APG） inducing. The product is thoroughly characterized with the Fourier transform infrared spectroscopy （FrIR）, the electron spectroscopy for chemical analysis （ESCA）, the thermogravimetric （TG） and the scanning electron microscopy （SEM）. It is found that chitosan is successfully grafted onto PBTNW. In addition, the water contact angles, hemolysis tests and cytotoxicity evaluation tests show an improvement in wettability and biocompatihility as a result of graft copolymerization of chitosan. So the CS-grafted PBTNW exhibits greater superiority than the original PBTNW. The CS-grafted PBTNW can be a candidate for blood filter materials and other medical applications.展开更多
A combined beam model representing the periodicity of the microstructure and micro deformation of 3D woven composites is developed for predicting mechanical properties. The model considers the effects of off axial ten...A combined beam model representing the periodicity of the microstructure and micro deformation of 3D woven composites is developed for predicting mechanical properties. The model considers the effects of off axial tension/compression and bending/shearing couplings as well as the mutual reactions of fiber yarns. The method determining microstructure by using woven parameters is described for a typical 3D woven composite material. An analytical cell, constructed by a minimum periodic section of yarn and interlayer matrix, is adopted. Micro stresses in the cell under in-plane tensile loading are obtained by using the proposed beam model and macro modulus is then obtained by the averaging method. Material tests and a 2D micro FEM analysis are made to evaluate this model. Analyses reveal that micro stress caused by tensile/bending coupling effect is not negligible in the stress analysis.展开更多
A micromechanical model for elastic behavior analysis of angle-interlock woven ceramic composites is proposed in this paper. This model takes into account the actual fabric structure by considering the fiber undulatio...A micromechanical model for elastic behavior analysis of angle-interlock woven ceramic composites is proposed in this paper. This model takes into account the actual fabric structure by considering the fiber undulation and continuity in space, the cavities between adjacent yarns and the actual cross-section geometry of the yarn. Based on the laminate theory, the elastic properties of 3D angle-interlock woven ceramic composites are predicted. Different numbers of interlaced wefts have almost the same elastic moduli. The thickness of ceramic matrix has little effect on elastic moduli. When the undulation ratio increases longitudinal modulus decreases and the other Young＇s moduli increase. Good agreement between theoretical predictions and experimental results demonstrates the feasibility of the proposed model in analyzing the elastic properties of 3D angle-interlock woven ceramic composites. The results of this paper verify the fact that the method of analyzing polyester matrix composites is suitable for woven ceramic composites.展开更多
Woven coronary artery (WCA) is a rare and underdiagnosed anomaly characterized by epicardial coronary artery dividing into multiple twisted single channels then anastomosing at distal segment. The malformation is usua...Woven coronary artery (WCA) is a rare and underdiagnosed anomaly characterized by epicardial coronary artery dividing into multiple twisted single channels then anastomosing at distal segment. The malformation is usually believed as a benign condition without traces of thrombosis or dissection flaps, and merely diagnosed incidentally. However, coincidence of WCA with atherosclerosis or tachycardia may incur myocardium ischemia,[1] and even caused acute coronary syndrome (ACS) or sudden cardiac death (SCD) in reported cases.[2–4] Since the absence of evidence, the guideline for management of the coronary malformation is still lacking. Notably, as an intravascular image modality with high resolution,[5] optical coherence tomography (OCT) may shed lights on diagnosis and management of WCA.[2] Herein, we reported three cases of optimizing WCA management through performing OCT.展开更多
The bending behavior of woven fabrics under low curva-ture conditions has been analyzed by linear viscoelastictheory.The fabric is assumed to behave viscoelasticallyand to be subjected to frictional restraints in bend...The bending behavior of woven fabrics under low curva-ture conditions has been analyzed by linear viscoelastictheory.The fabric is assumed to behave viscoelasticallyand to be subjected to frictional restraints in bending de-formation.The frictional restraint is considered to beproportional to the curvature and can be described by africtional moment.A model has been constructed by astandard three-element solid model and a paralleledfrictional sliding element.The equations of the model fora cyclic curvature variation are derived.A set of param-eters of the equations for each fabric has been obtainedexperimentally.Predictions of the bending rigidity andhysteresis for wool,cashmere,wool/polyester blended,polyester and cotton fabrics are made,displaying verygood agreement with the experimental observations.展开更多
The paper introduces a new technique for the treatment of the woven fabrics. Sprayed by high pressure water jet, the appearance, handle and stiffness of the fabric are improved. Other properties of the high pressure w...The paper introduces a new technique for the treatment of the woven fabrics. Sprayed by high pressure water jet, the appearance, handle and stiffness of the fabric are improved. Other properties of the high pressure water treated fabrics like drape coefficient, air permeability, tenacity are also presented.展开更多
文摘Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. In service environments, CMCs exhibit complex damage mechanisms and failure modes, which are affected by constituent materials, meso-architecture and inhere defects. In this paper, the in-plane tensile mechanical behavior of a plain-woven SiCf/SiC composite at room and elevated temperatures was investigated, and the factors affecting the tensile strength of the material were discussed in depth. The results show that the tensile modulus and strength of SiCf/SiC composites at high temperature are lower, but the fracture strain increases and the toughness of the composites is enhanced;the stitching holes significantly weaken the tensile strength of the material, resulting in the material is easy to break at the cross-section with stitching holes.
基金financial support from the Hunan Provincial Key Research and Development Program(2020WK2018)the Arts Crafts Industrial Design Center of Hunan Province(No.2022GYMSZ2)the Scientific Innovation Fund for Post-Graduates of Central South University of Forestry and Technology(No.2022CX02079).
文摘In the study,it is proposed that a coordinate-parametric matrix model is performed to a square-conjoint pattern of cross woven(SCPCW)in the bamboo mat.The patterns of SCPCW are firstly detected according to the perspective of configuration,which is divided into the basic-monomer shape and the basic combination shape.Secondly,the compositions of design patterns in SCPCW are analyzed to attain the trend of curve shape.Based on the coordinate-parametric matrix model,the specimens of SCPCW are subsequently accomplished to elaborate the woven logic of bamboo mats.The digital innovation of SCPCW,defined by a mathematical resolution,is implemented by the software of Grasshopper(GH),which plays a crucial role in capturing image information by the Image Sampler component.Successively,the weaving logic of coordinated matrix is referred to apply in the computing component of Grasshopper software.Finally,the computer simulation could demonstrate that the coordinate-parametric matrix model of SCPCWwould be realized to analyze the micro-weaving structure and overall weaving effect in the bamboo mat.
基金Fundamental Research Funds for the Central Universities,China(Nos.2232022D-11 and 22D128102/007)Jiangsu Transformation and Upgrading Funding Program for Industrial and Information Industry,ChinaShanghai Natural Science Foundation of Shanghai Municipal Science and Technology Commission,China(No.20ZR1401600)。
文摘With the wide use of three-dimensional woven spacer composites(3DWSCs),the market expects greater mechanical properties from this material.By changing the weft fastening method of the traditional I-shape pile yarns,we designed three-dimensional woven spacer fabrics(3DWSFs)and 3DWSCs with the weft V-shape to improve the compression performance of traditional 3DWSFs.The effects of weft binding structures,V-pile densities,and V-shaped angle were investigated in this paper.It is found that the compression resistance of 3DWSFs with the weft V-shape is improved compared to that with the weft I-shape,the fabric height recovery rate is as high as 95.7%,and the average elastic recovery rate is 59.39%.When the interlayer pile yarn density is the same,the weft V-shaped and weft I-shaped 3DWSCs have similar flatwise pressure and edgewise pressure performance.The compression properties of the composite improve as the density of the V-pile yarns increases.The flatwise compression load decreases as the V-shaped angle decreases.When the V-shaped angle is 28°and 42°,the latitudinal V-shaped 3DWSCs perform exceptionally well in terms of anti-compression cushioning.The V-shaped weft binding method offers a novel approach to structural design of 3DWSCs.
文摘In this paper,using Parseval frames we generalize Sun’s results to g-frames in Hilbert C^(*)-modules.Moreover,for g-frames in Hilbert spaces,we present some characterizations in terms of a family of frames,not only for orthonormal bases.Also,we have a note about a comment and a relation in the proof of Proposition 5.3 in[D.Li et al.,On weaving g-frames for Hilbert spaces,Complex Analysis and Operator Theory,2020].Finally,we have some results for g-Riesz bases,woven and P-woven g-frames.
文摘The curriculum“Woven Fabric Structure Design and Application”is the core curriculum of textile majors in higher vocational colleges,which plays a very important role in the cultivation of students’vocational ability and professional quality.The curriculum reform of“Woven Fabric Structure Design and Application”through the deep cooperation of industry-college partnerships,the comprehensive analysis of the major training objectives and graduation requirements,the redesign of the curriculum teaching content,the improvement of the teaching method and the examination method,has achieved good results.
文摘A micro mechanical model is carried out to predict micro stresses and macro elastic properties of 3-D woven composites. A unit cell is composed of two phases. One is fiber yarn and the other is resin or fiber yarn in transverse. The additional shearing introduced by bending of fiber yarn is considered. The method to determine the microstructure is also discussed. This model is applied to the analysis of a 3-D woven graphite/epoxy composite. Micro stresses of the cell are studied, and then macro modulus is obtained by employing the average method. The predictions agree well with experimental results.
文摘The outbreak of coronavirus has led to an increase in the demand for facemasks globally. Unavailability of appropriate polypropylene non-woven fabrics face masks as a result of inadequate supply to satisfy the growing population has brought about the manufacturing of locally fabrics masks to augment or substitute standard medical class facemasks. The study aims at analyzing airflow of these locally manufactured fabrics to determine possible means of transmitting the virus as well as establish comfort of the user of these masks. Standard polypropylene non-woven, woven and knitted fabrics were considered for the study. Air permeability test was conducted on these fabrics using Frazier Air permeability tester. Depending on the property significant variation in the textile fabrics, polypropylene non-woven is widely accepted for facial masks. Nevertheless, this study illustrates that woven and knitted fabrics have more open structures, which allow a high rate of air penetration and so may require two or three layers to prevent antimicrobial or antiviral potential.
文摘In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It has important value to study on the relationship between tribological performances of the liner and the friction heat. Unforttmately, up to now, published work on this relationship is quite scarce. Therefore, the effect of friction heat on the tribological performances of the liner was investigated in the present work. The tribological behaviors of the liner were evaluated by using the high temperature end surface wear tester. Scanning electron microscopy （SEM） was utilized to examine the morphologies of worn surfaces of the liner and study the failure modes. Differential scanning calorimetry （DSC） measurement and X-ray diffraction （XRD） analysis were performed to study the behaviors of the wear debris. The temperature rise on the worn surface was calculated according to classical models. SEM observation shows that the dominating wear mechanism for the liner is mainly affected by friction shear force, contact pressure and friction heat. Higher fusion heat for the wear debris than that for the pure polytetrafluroethylene （PTFE） indicates that the PTFE is the main portion of the wear debris, and, the PTFE in the wear debris shows a higher crystallisation degree owing to the effects of friction shear force and the friction heat. Combining the calculated temperature rise results with the wear rate of the liner, it can be concluded that the effects of temperature rise o n the tribological performances of the liner become more obvious when the temperature rise exceeds the glass transition temperature （Tg） of the PTFE. The wear resistance of the liner deteriorates dramatically when the temperature rise approaches to the melting point （Ton） of the PTFE. The tribological performances of the liner can be improved when the temperature rise exceeds Tg but is far lower than Ton- The present study on the relationship between the temperature rise and the tribological performances of the liner may provide the basis for further understanding of the wear mechanisms of the liner as well as the relationship between the formation of the PTFE transfer film and the friction heat during the dry-sliding of the Finer.
文摘In order to improve the wettability and biocompatibility of the poly （butylene terephthalate） non-woven （PBTNW）, the method of surface modification is used to graft copolymerization of chitosan （CS） onto the PBTNW under alkylpolyglycoside （APG） inducing. The product is thoroughly characterized with the Fourier transform infrared spectroscopy （FrIR）, the electron spectroscopy for chemical analysis （ESCA）, the thermogravimetric （TG） and the scanning electron microscopy （SEM）. It is found that chitosan is successfully grafted onto PBTNW. In addition, the water contact angles, hemolysis tests and cytotoxicity evaluation tests show an improvement in wettability and biocompatihility as a result of graft copolymerization of chitosan. So the CS-grafted PBTNW exhibits greater superiority than the original PBTNW. The CS-grafted PBTNW can be a candidate for blood filter materials and other medical applications.
文摘A combined beam model representing the periodicity of the microstructure and micro deformation of 3D woven composites is developed for predicting mechanical properties. The model considers the effects of off axial tension/compression and bending/shearing couplings as well as the mutual reactions of fiber yarns. The method determining microstructure by using woven parameters is described for a typical 3D woven composite material. An analytical cell, constructed by a minimum periodic section of yarn and interlayer matrix, is adopted. Micro stresses in the cell under in-plane tensile loading are obtained by using the proposed beam model and macro modulus is then obtained by the averaging method. Material tests and a 2D micro FEM analysis are made to evaluate this model. Analyses reveal that micro stress caused by tensile/bending coupling effect is not negligible in the stress analysis.
基金Project supported by the National Natural Science Foundation of China (No.90405015)
文摘A micromechanical model for elastic behavior analysis of angle-interlock woven ceramic composites is proposed in this paper. This model takes into account the actual fabric structure by considering the fiber undulation and continuity in space, the cavities between adjacent yarns and the actual cross-section geometry of the yarn. Based on the laminate theory, the elastic properties of 3D angle-interlock woven ceramic composites are predicted. Different numbers of interlaced wefts have almost the same elastic moduli. The thickness of ceramic matrix has little effect on elastic moduli. When the undulation ratio increases longitudinal modulus decreases and the other Young＇s moduli increase. Good agreement between theoretical predictions and experimental results demonstrates the feasibility of the proposed model in analyzing the elastic properties of 3D angle-interlock woven ceramic composites. The results of this paper verify the fact that the method of analyzing polyester matrix composites is suitable for woven ceramic composites.
基金supported by grants from National Key R&D Program of China (2016YFC1300304)
文摘Woven coronary artery (WCA) is a rare and underdiagnosed anomaly characterized by epicardial coronary artery dividing into multiple twisted single channels then anastomosing at distal segment. The malformation is usually believed as a benign condition without traces of thrombosis or dissection flaps, and merely diagnosed incidentally. However, coincidence of WCA with atherosclerosis or tachycardia may incur myocardium ischemia,[1] and even caused acute coronary syndrome (ACS) or sudden cardiac death (SCD) in reported cases.[2–4] Since the absence of evidence, the guideline for management of the coronary malformation is still lacking. Notably, as an intravascular image modality with high resolution,[5] optical coherence tomography (OCT) may shed lights on diagnosis and management of WCA.[2] Herein, we reported three cases of optimizing WCA management through performing OCT.
文摘The bending behavior of woven fabrics under low curva-ture conditions has been analyzed by linear viscoelastictheory.The fabric is assumed to behave viscoelasticallyand to be subjected to frictional restraints in bending de-formation.The frictional restraint is considered to beproportional to the curvature and can be described by africtional moment.A model has been constructed by astandard three-element solid model and a paralleledfrictional sliding element.The equations of the model fora cyclic curvature variation are derived.A set of param-eters of the equations for each fabric has been obtainedexperimentally.Predictions of the bending rigidity andhysteresis for wool,cashmere,wool/polyester blended,polyester and cotton fabrics are made,displaying verygood agreement with the experimental observations.
文摘The paper introduces a new technique for the treatment of the woven fabrics. Sprayed by high pressure water jet, the appearance, handle and stiffness of the fabric are improved. Other properties of the high pressure water treated fabrics like drape coefficient, air permeability, tenacity are also presented.
