The simulation of a control system for the longitudinal axis of the rotary or fixed-wing unmanned aerial vehicles(UAVs)is demonstrated in this study.The control unit includes design considerations of two controllers t...The simulation of a control system for the longitudinal axis of the rotary or fixed-wing unmanned aerial vehicles(UAVs)is demonstrated in this study.The control unit includes design considerations of two controllers to provide robust stability,tracking of the proposed linear dynamics,an adequate set of proportional-integral-derivative(PID)controller gains,and a minimal cost function.The PID control and linear quadratic regulator(LQR)with or without full-state-observer were evaluated.An optimal control system is assumed to provide fast rise and settling time,minimize overshoot,and eliminate the steady-state error.The effectiveness of this approach was verified by a linear model of the UAV aircraft in the semi-dynamic simulation platform of Matlab/Simulink,in which the open-loop system was assessed in terms of flight robustness and reference tracking.The experimental results show that the proposed controllers effectively improve the configuration of the control system of the plant,maintain the sustainability of the dynamic flight model stability,and diminish the flight controller errors.The LQR provides robust stability,but it is not optimal in the transient phase of particular plant output.The PID control system can adjust the controller’s gains for optimal hovering(or stable slow flight)and is especially useful for the tracking system.Finally,comparing aircraft stability using PID and LQR controllers shows that the latter has less overshoot and a shorter settling time;in addition,all proposed controllers can be practically deployed as one UAV’s system,which can be handled as an exemplary model of the UAV flight management system.展开更多
The adulteration concentration of palm kernel oil(PKO)in virgin coconut oil(VCO)was quantified using near-infrared(NIR)hyperspectral imaging.Nowadays,some VCO is adulterated with lower-priced PKO to reduce production ...The adulteration concentration of palm kernel oil(PKO)in virgin coconut oil(VCO)was quantified using near-infrared(NIR)hyperspectral imaging.Nowadays,some VCO is adulterated with lower-priced PKO to reduce production costs,which diminishes the quality of the VCO.This study used NIR hyperspectral imaging in the wavelength region 900-1,650 nm to create a quantitative model for the detection of PKO contaminants(0-100%)in VCO and to develop predictive mapping.The prediction equation for the adulteration of VCO with PKO was constructed using the partial least squares regression method.The best predictive model was pre-processed using the standard normal variate method,and the coefficient of determination of prediction was 0.991,the root mean square error of prediction was 2.93%,and the residual prediction deviation was 10.37.The results showed that this model could be applied for quantifying the adulteration concentration of PKO in VCO.The prediction adulteration concentration mapping of VCO with PKO was created from a calibration model that showed the color level according to the adulteration concentration in the range of 0-100%.NIR hyperspectral imaging could be clearly used to quantify the adulteration of VCO with a color level map that provides a quick,accurate,and non-destructive detection method.展开更多
The necessity to saline and sodic waters is sometimes used for irrigating agricultural activities under certain circumstances, but it is important to note that the use of these waters comes with specific consideration...The necessity to saline and sodic waters is sometimes used for irrigating agricultural activities under certain circumstances, but it is important to note that the use of these waters comes with specific considerations and limitations. One way to decrease undesirable effects of sodic waters on the physical and chemical properties of soils is to apply organic and chemical amendments within the soil. This study aimed to assess the effectiveness of saline water on soil acidity, alkalinity and nutrients leaching in sandy loamy soil at Bella flower farm, in Rwamagana District, Rwanda. The water used was from the Muhazi Lake which is classified as Class I (Saline water quality). Column leaching experiments using treated soils were then conducted under saturated conditions. The soil under experimental was first analyzed for its textural classification, soil properties and is classified as sandy loamy soil. The t-test was taken at 1%, 5% and 10% levels of statistical significance compared to control soil. The results indicated that the application of saline water to soils caused an increase in some soil nutrients like increase of Phosphorus (P), Potassium (K<sup>+</sup>), Magnesium (Mg2<sup>+</sup>), Sulphur (S), CN ratio and Sodium (Na<sup>+</sup>) and decreased soil texture, physical and chemical properties and remained soil nutrients. Consequently, the intensive addition of saline water leachates to soil in PVC pipes led to decreased of soil EC through leaching and a raiser Soluble Sodium Percentage (SSP). The rate of saline water application affected the increase accumulation of SAR and Na% in the top soil layers. The study indicated that saline water is an inefficient amendment for sandy soil with saline water irrigation. The study recommends further studies with similar topic with saline water irrigation, as it accentuated the alkalinity levels.展开更多
Mechanical properties of ukam, banana, sisal, coconut, hemp and e-glass fibre reinforced laminates were evaluated to assess the possibility of using it as new material in engineering applications. Samples were fabrica...Mechanical properties of ukam, banana, sisal, coconut, hemp and e-glass fibre reinforced laminates were evaluated to assess the possibility of using it as new material in engineering applications. Samples were fabricated by the hand lay-up process (30:70 fibre and matrix ratio by weight) and the properties evaluated using the INSTRON material testing system. The mechanical properties were tested and showed that glass laminate has the maximum tensile strength of 63 MPa, bending strength of 0.5 MPa, compressive strength of 37.75 MPa and the impact strength of 17.82 J/m2. The ukam plant fibre laminate has the maximum tensile strength of 16.25 MPa and the impact strength of 9.8J/m among the natural fibres;the sisal laminate has the maximum compressive strength of 42 MPa and maximum bending strength of 0.0036 MPa among the natural fibres. Results indicated that natural fibres are of interest for low-cost engineering applications and can compete with artificial glass fibres (E-glass fibre) when a high stiffness per unit weight is desirable. Results also indicated that future research towards significant improvements in tensile and impact strength of these types of composites should focus on the optimisation of fibre strength rather than interfacial bond strength.展开更多
The estuary tides affect groundwater dynamics;these areas are susceptible to waterlogging and salinity issues.A study was conducted on two fields with a total area of 60 hectares under a center pivot irrigation system...The estuary tides affect groundwater dynamics;these areas are susceptible to waterlogging and salinity issues.A study was conducted on two fields with a total area of 60 hectares under a center pivot irrigation system that works with solar energy and belong to a commercial farm located in Northern Sudan.To monitor soil salinity and calcium carbonate in the area and stop future degradation of soil resources,easy,non-intrusive,and practical procedures are required.The objective of this study was to use remote sensing-determined Sentinel-2 satellite imagery using various soil indices to develop prediction models for the estimation of soil electrical conductivity(EC)and soil calcium carbonate(CaCO_(3)).Geo-referenced soil samples were collected from 72 locations and analyzed in the laboratory for soil EC and CaCO_(3).The electrical conductivity of the soil saturation paste extract was represented by average values in soil dataset samples from two fields collected from the topsoil layer(0 to 15 cm)characteristic of the local salinity gradient.The various soil indices,used in this study,were calculated from the Sentinel-2 satellite imagery.The prediction was determined using the root mean square error(RMSE)and cross validation was done using coefficient of determination.The results of regression analysis showed linear relationships with significant correlation between the EC analyzed in laboratory and the salinity index-2“SI2”(Model-1:R^(2)=0.59,p=0.00019 and root mean square error(RMSE=1.32%)and the bare soil index“BSI”(Model-2:R^(2)=0.63,p=0.00012 and RMSE=6.42%).Model-1 demonstrated the best model for predicting soil EC,and validation R^(2)and RMSE values of 0.48%and 1.32%,respectively.The regression analysis results for soil CaCO_(3)determination showed linear relationships with data obtained in laboratory and the bare soil index“BSI”(Model-3:R^(2)=0.45,p=0.00021 and RMSE=1.29%)and the bare soil index“BSI”&Normalized difference salinity index“NDSI”(Model-4:R^(2)=0.53,p=0.00015 and RMSE=1.55%).The validation confirmed the Model-3 results for prediction of soil CaCO_(3)with R^(2)and RMSE values of 0.478%and 1.29%,respectively.Future soil monitoring programs might consider the use of remote sensing data for assessing soil salinity and CaCO_(3)using soil indices results generated from satellite image(i.e.,Sentinel-2).展开更多
Deficiencies of essential vitamins,iron(Fe),and zinc(Zn)affect over one-half of the world’s population.A significant progress has been made to control micronutrient deficiencies through supplementation,but new approa...Deficiencies of essential vitamins,iron(Fe),and zinc(Zn)affect over one-half of the world’s population.A significant progress has been made to control micronutrient deficiencies through supplementation,but new approaches are needed,especially to reach the rural poor.Agronomic biofortification of pulses with Zn,Fe,and boron(B)offers a pragmatic solution to combat hidden hunger instead of food fortification and supplementation.Moreover,it also has positive effects on crop production as well.Therefore,we conducted three separate field experiments for two consecutive years to evaluate the impact of soil and foliar application of the aforementioned nutrients on the yield and seed biofortification of mungbean.Soil application of Zn at 0,4.125,8.25,Fe at 0,2.5,5.0 and B at 0,0.55,1.1 kg ha−1 was done in the first,second and third experiment,respectively.Foliar application in these experiments was done at 0.3%Zn,0.2%Fe and 0.1%B respectively one week after flowering initiation.Data revealed that soil-applied Zn,Fe and B at 8.25,5.0 and 1.1 kg ha−1,respectively,enhanced the grain yield of mungbean;however,this increase in yield was statistically similar to that recorded with Zn,Fe and B at 4.125,2.5 and 0.55 kg ha−1,respectively.Foliar application of these nutrients at flower initiation significantly enhanced the Zn contents by 28%and 31%,Fe contents by 80%and 78%,while B contents by 98%and 116%over control during 2019 and 2020,respectively.It was concluded from the results that soil application of Zn,Fe,and B enhanced the yield performance of mungbean;while significant improvements in seed Zn,Fe,and B contents were recorded with foliar application of these nutrients.展开更多
Nitrogen(N),the building block of plant proteins and enzymes,is an essential macronutrient for plant functions.A field experiment was conducted to investigate the impact of different N application rates(28,57,85,114,1...Nitrogen(N),the building block of plant proteins and enzymes,is an essential macronutrient for plant functions.A field experiment was conducted to investigate the impact of different N application rates(28,57,85,114,142,171,and 200 kg ha^(−1))on the performance of spring wheat(cv.Ujala-2016)during the 2017–2018 and 2018–2019 growing seasons.A control without N application was kept for comparison.Two years mean data showed optimum seed yield(5,461.3 kg ha^(−1))for N-application at 142 kg ha^(−1) whereas application of lower and higher rates of N did not result in significant and economically higher seed yield.A higher seed yield was obtained in the 2017–2018(5,595 kg ha^(−1))than in the 2018–2019(5,328 kg ha^(−1))growing seasons under an N application of 142 kg ha^(−1).It was attributed to the greater number of growing degree days in the first(1,942.35°C days)than in the second year(1,813.75°C).Higher rates of N(171 and 200 kg ha^(−1))than 142 kg ha^(−1) produced more number of tillers(i.e.,948,300 and 666,650 ha^(−1),respectively).However,this increase did not contribute in achieving higher yields.Application of 142,171,and 200 kg ha^(−1) resulted in 14.15%,15.0%and 15.35%grain protein concentrations in comparison to 13.15%with the application of 114 kg ha^(−1).It is concluded that the application of N at 142 kg ha^(−1) could be beneficial for attaining higher grain yields and protein concentrations of wheat cultivar Ujala-2016.展开更多
Land suitability analysis of Moringa oleifera tree cultivation is important to enhance its product,as the demand forthis tree for medicinal values and food sources is increasing worldwide.Therefore,this study aimed to...Land suitability analysis of Moringa oleifera tree cultivation is important to enhance its product,as the demand forthis tree for medicinal values and food sources is increasing worldwide.Therefore,this study aimed to assess suitableland for Moringa oleifera tree cultivation by using the integration of multi-criteria evaluation with geospatialtechnologies in the Dhidhessa catchment,western Ethiopia.Five parameters,namely:slope,land use and landcover(LULC),soil texture,land surface temperature,and rainfall data,were used in this study.The land suitabilityevaluation of Moringa oleifera is classified into three classes as highly suitable,moderately suitable,and notsuitable.The results revealed that,about 344.4 km2(12.2%)of the area is categorized into highly suitable,and2343.7 km2(83%)is moderately suitable for Moringa tree,whereas,137.2 km2(4.9%)is categorized as notsuitable for Moringa oleifera tree cultivation.Hence,based on the finding of the study,we suggested that farmers andother stakeholders can cultivate Moringa oleifera trees in the Dhidhessa catchment.展开更多
The availability of favorable genetic diversity is a thriving vitality for the success of a breeding program.It provides a firm basis of selecting superior breeding lines for the development of high yielding crop geno...The availability of favorable genetic diversity is a thriving vitality for the success of a breeding program.It provides a firm basis of selecting superior breeding lines for the development of high yielding crop genotypes.In this context,present investigation aimed to generate information on genetic divergence and character association in a diversity panel of 123 local and exotic soybean genotypes.Analysis of variance revealed significant response of the evaluated genotypes based on studied attributes.It depicted the probability of selecting desirable soybean genotypes by focusing on character association studies and genetic diversity analysis.Correlation analysis revealed that seed yield per plant showed high positive correlation with 100-seed weight followed by pods per plant and plant height.Furthermore,path coefficient analysis exposed that pods per plant had maximum direct contribution in seed yield per plant followed by 100-seed weight,days to flowering and SPAD measurement.Genotype named“G-10”showed maximum yield per plant followed by 24607,G-52,24593,Arisoy,24566,17426,A-3127,24570 and 24567.Genetic diversity analysis grouped the evaluated germplasm into 17 clusters.All clusters showed zero intra-cluster variability;while inter-cluster divergence ranged from 9.00 to 91.11.Cluster V showed maximum inter-cluster distance with cluster XII followed by that of between V and VIII.Moreover,cluster IV with superior genotypes(G-10,24607,24593 and 24566),VI(17426 and 24567),XIII(24570)and X(Arisoy and G-52)showed above mean values for most of the studied characters.Overall,the results of hybridization between the superior genotypes of these cluster pairs might be useful for soybean breeding with improving agronomic traits and adaptability.展开更多
The thrust of this research study was to ascertain the physicochemical characteristic in settling particulate matter and sediments of samples collected from the wellington industrial estate flood plains;the main of ob...The thrust of this research study was to ascertain the physicochemical characteristic in settling particulate matter and sediments of samples collected from the wellington industrial estate flood plains;the main of objectives are as follows: to determine the hydrogen ion index (pH) of the samples collected in the study area, to determine the electrical conductivity (EC) of the samples collected from the same location. Samples were collected from six locations (at varying depths of 0 - 5 cm and 5 - 10 cm) sample area 1 (Wellington Industrial Estate Area 1) WIEA1 WIEA 2, WIEA 3, WIEA 4, WIEA 5 and WIEA 6 and were given laboratory treatment. A laboratory thermometer was used to determine temperature of the samples when collected;(Dakton model) pH meter equipment and a Toledo electrical conductivity meter were used to determine the pH and EC respectively. The results indicated that the samples were acidic (low pH) and the conductivity of the samples was of medium and low range. This therefore expressed low levels of soluble metal ions in the environment that have effect on plants, animals and other organisms, agricultural and domestic activities in the environment under investigation. Hence bioconcentration and biomagnification are highly likely in these locations.展开更多
Climate variability impacts on cocoa production are evaluated for the first time using 31 years (1979-2010) of data from SODEXAM (climate ground- based observations) and the ex-CAISTAB in three main cocoa production r...Climate variability impacts on cocoa production are evaluated for the first time using 31 years (1979-2010) of data from SODEXAM (climate ground- based observations) and the ex-CAISTAB in three main cocoa production regions (Goh, Marahoué, and Haut-Sassandra) in the west-central part of Cote d’Ivoire. The work is a contribution to improving the quality of climate services dedicated to cocoa cultivation to ensure producers’ income and improve the yield of the production in the west-central part of Cote d’Ivoire. The results show that cocoa production is affected by the changes and variability in climate conditions (i.e. rainfall and temperature). In the Goh region, the increase in cocoa production seems to be mostly related to the augmentation of rainfall amount while in Marahoué, the increase in temperature is identified to have a more significant impact. Over the Haut-Sassandra region, both temperature and rainfall seem to have a considerable effect on the changes in cocoa production. The analysis based on linear regression by least-squares fit shows two characteristic modes (low and high-frequency variability) in the relationships between cocoa production and meteorological conditions suggesting a strong temporal signal impact related to the changes in the emblazoned surfaces. This leads to an important impact of the short-term variations of climate in cocoa production whereas, the influence of the long-term variability in climate on the cocoa yield seems marginal.展开更多
Floods are phenomenon with significant socio-economic implications mainly for human loss, agriculture, livestock, soil loss and land degradation, for which many researchers try to identify the most appropriate methodo...Floods are phenomenon with significant socio-economic implications mainly for human loss, agriculture, livestock, soil loss and land degradation, for which many researchers try to identify the most appropriate methodologies by analyzing their temporal and spatial development. This study therefore attempts to employ the GIS-based multi-criteria decision analysis and analytical hierarchy process techniques to derive the flood risks management on rice productivity in the Gishari Agricultural Marshland in Rwamagana district, Rwanda. Here, six influencing potential factors to flooding, including river slope, soil texture, Land Use Land Cover through Land Sat 8, rainfall, river distance and Digital Elevation Model are considered for the delineation of flood risk zones. Data acquisition like Landsat 8 images, DEM, land use land cover, slope, and soil class in the study area were considered. Results showed that if the DEM is outdated or inaccurate due to changes in the terrain, such as construction, excavation, or erosion, the predicted flood patterns might not reflect the actual water flow. This could result unexpected flood extents and depths, potentially inundating rice fields that were not previously at risk and this, expectedly explained that the increase 1 m in elevation would reduce the rice productivity by 0.17% due to unplanned flood risks in marshland. It was found that the change in rainfall distribution in Gishari agricultural marshland would also decrease the rice productivity by 0.0018%, which is a sign that rainfall is a major factor of flooding in rice scheme. Rainfall distribution plays a crucial role in flooding analysis and can directly impact rice productivity. Oppositely, another causal factor was Land Use Land Cover (LULC), where the Multivariate Logistic Regression Model Analysis findings showed that the increase of one unit in Land Use Land Cover would increase rice productivity by 0.17% of the total rice productivity from the Gishari Agricultural Marshland. Based on findings from these techniques, the Gishari Agricultural Marshlands having steeped land with grassland is classified into five classes of flooding namely very low, low, moderate, high, and very high which include 430%, 361%, 292%, 223%, and 154%. Government of Rwanda and other implementing agencies and major key actors have to contribute on soil and water conservation strategies to reduce the runoff and soil erosion as major contributors of flooding.展开更多
The effects of biomimetic designs of tine furrow opener surface on equivalent pressure and pressure in the direction ofmotion on opener surface against soil were studied by finite element method (FEM) simulation and t...The effects of biomimetic designs of tine furrow opener surface on equivalent pressure and pressure in the direction ofmotion on opener surface against soil were studied by finite element method (FEM) simulation and the effects of these designson tool force and power requirements were examined experimentally.Geometrical structures of the cuticle surfaces of dungbeetle (Copris ochus Motschulsky) were examined by stereoscopy.The structures of the cuticle surfaces and Ultra High Mo-lecular Weight Polyethylene (UHMWPE) material were modeled on surface of tine furrow opener as biomimetic designs.Sevenfurrow openers were analyzed in ANSYS program (a FEM simulation software).The biomimetic furrow opener surfaces withUHMWPE structures were found to have lower equivalent pressure and pressure in the direction of motion as compared to theconventional surface and to the biomimetic surfaces with textured steel-35 structures.It was found that the tool force and powerwere increased with the cutting depth and operating speed and the biomimetic furrow opener with UHMWPE tubular sectionridges showed the lowest resistance and power requirement against soil..展开更多
The “Huang gua” melons were measured for their physical properties including firmness and static elastic modulus. The vibrational characteristics of fruits and vegetables are governed by their elastic modulus (firmn...The “Huang gua” melons were measured for their physical properties including firmness and static elastic modulus. The vibrational characteristics of fruits and vegetables are governed by their elastic modulus (firmness), mass, and geometry. Therefore, it is possible to evaluate firmness of fruits and vegetables based on their vibrational characteristics. Analysis of the vibration responses of a fruit is suggested for measuring elastic properties (Firmness) non-destructively. The impulse response method is often used to measure firmness of fruits. The fruit was excited using three types of balls (wooden, steel and rubber) and the vibration is detected by an accelerometer. The Instron device was used to measure the static elastic modulus of the inner, middle and outer portions of melon flesh. Finite element (FE) technique was used to determine the optimum excitation location of the chosen measurement sensor and to analyze the mode shape fruits. Four types of mode shapes (torsional or flexural mode shape, first-type, second-type spherical mode and breathing mode shape) were found. Finite element simulation results agreed well with experimental results. Correlation between the firmness and resonant frequency (r2=0.91) and between the resonant frequency and stiffness factor (r2=0.74) existed. The optimum location and suitable direction for excitation and response measurement on the fruit were suggested.展开更多
The effect of external roof shading on the spatial distribution of air temperature and relative humidity in a greenhouse(Tin and RHin) was evaluated under the arid climatic conditions of Riyadh City, Saudi Arabia. Two...The effect of external roof shading on the spatial distribution of air temperature and relative humidity in a greenhouse(Tin and RHin) was evaluated under the arid climatic conditions of Riyadh City, Saudi Arabia. Two identical, evaporatively-cooled, single-span greenhouses were used in the experiment. One greenhouse was externally shaded(Gs) using a movable black plastic net(30% transmissivity), and the other greenhouse was kept without shading(Gc). Strawberry plants were cultivated in both greenhouses. The results showed that the spatial distribution of the Tin and RHin was significantly affected by the outside solar radiation and evaporative cooling operation. The regression analysis showed that when the outside solar radiation intensity increased from 200 to 800 W m–2, the Tin increased by 4.5℃ in the Gc and 2℃in the Gs, while the RHin decreased by 15% in the Gc and 5% in the Gs, respectively. Compared with those in the Gc, more uniformity in the spatial distribution of the Tin and RHin was observed in the Gs. The difference between the maximum and minimum Tin of 6.4℃ and the RHin of 10% was lower in the Gs than those in the Gc during the early morning. Around 2℃ difference in the Tin was shown between the area closed to the exhausted fans and the area closed to the cooling pad with the external shading. In an evaporatively-cooled greenhouse in arid regions, the variation of the Tin and RHin in the vertical direction and along the sidewalls was much higher than that in the horizontal direction. The average variation of the Tin and RHin in the vertical direction was 5.2℃ and 10% in the Gc and 5.5℃ and 13% in the Gs, respectively. The external shading improved the spatial distribution of the Tin and RHin and improved the cooling efficiency of the evaporative cooling system by 12%, since the transmitted solar radiation and accumulated thermal energy in the greenhouse were significantly reduced.展开更多
It is noted that any variation in operating conditions has a considerable effect on the tire/road interaction. Furthermore,choosing a range of proper values for carcass stiffness is very essential for both tire safety...It is noted that any variation in operating conditions has a considerable effect on the tire/road interaction. Furthermore,choosing a range of proper values for carcass stiffness is very essential for both tire safety and effective driving action. In this work,an elaborated 3D model fully compliant with the geometrical size of radial tire 185/60 R15 is worked up, for evaluating the effects of components properties and working conditions on deformation and stress/strain fields created inside the tire. For the simulation, the tire structure is assumed to be composed of tread, carcass ply, and bead. The mechanical behavior of rubber as main component of tire is described by Mooney-Rivlin material model. The comparison of the obtained results and laboratory tests demonstrates the validity and high accuracy of analysis.展开更多
The compaction and stress generation on terrain were always investigated based on empirical approaches or testing methods for tire/soil interaction.However,the analysis should be performed for various tires and at dif...The compaction and stress generation on terrain were always investigated based on empirical approaches or testing methods for tire/soil interaction.However,the analysis should be performed for various tires and at different soil strengths.With the increasing capacity of numerical computers and simulation software,finite element modeling of tire/terrain interaction seems a good approach for predicting the effect of change on the parameters.In this work,an elaborated 3D model fully complianning with the geometry of radial tire 115/60R13 was established,using commercial code Solidwork Simulation.The hyper-elastic and incompressible rubber as tire main material was analyzed by Moony-Rivlin model.The Drucker-Prager yield criterion was used to model the soil compaction.Results show that the model realistically predicts the laboratory tests outputs of the modeled tire on the soft soil.展开更多
The goal of this investigation was to analyze the impact of some production variables (input) on agricultural pro- ductivity growth (output) in China from 1989～2002. We selected through random sampling Zhejiang Provi...The goal of this investigation was to analyze the impact of some production variables (input) on agricultural pro- ductivity growth (output) in China from 1989～2002. We selected through random sampling Zhejiang Province for our disaggre- gate analysis with the use of Cobb-Douglas function. The estimation results showed that all key parameters are significant and are of the expected sign. Labor and that capital and land have positive impact on agricultural productivity growth.展开更多
Allelopathic effects of several concentrations of fresh tissue,dry powder and dry tissue of three bloom-forming green macroalgae Ulva pertusa,Ulva linza and Enteromopha intestinalis on the red tide microalga Heterosig...Allelopathic effects of several concentrations of fresh tissue,dry powder and dry tissue of three bloom-forming green macroalgae Ulva pertusa,Ulva linza and Enteromopha intestinalis on the red tide microalga Heterosigma akashiwo were evaluated in microcosms systems.The effects of macroalgae culture medium filtrate were investigated on H.akashiwo using initial or semi-continuous filtrate addition.Preliminary studies on the algicidal effects of one aqueous and four organic solvent extracts from the macroalgae on the microalga were carried out to confirm the existence of allelochemicals in the tissue of these macroalgae.The dry powder of U.pertusa was extracted with methanol,and the methanol extracts were partitioned to petroleum ether phase,ethyl acetate phase,butanol phase and distilled phase by liquid-liquid fractionation.The bioassays of the activity of every fraction were carried out on H.akashiwo.The resultant microcosms assay showed that the growth of H.akashiwo was strongly inhibited by using fresh tissues,dry powder or dry tissue of these three macroalgae,while aqueous and methanol extracts of both macroalgae had strong inhibitory effects on the growth of H.akashiwo,and the EC 50 values for methanol extract of U.pertusa,U.linza or E.intestinalis were 0.016,0.028×10-12 or 0.033×10-12,respectively.While the other three organic solvent extracts(acetone,ether and chloroform) had no apparent effect on its growth,this suggests that the allelochemicals from these three macroalgae had relatively high polarities.The activity of petroleum ether phase,ethyl acetate phase,butanol phase and distilled phase of U.pertusa methanol extract was carried out on H.akashiwo indicating that petroleum ether phase and ethyl acetate phase had stronger algicidal effect on H.akashiwo.The inhibition effect of the ethyl acetate phase was not as strong as that of petroleum ether phase,and effective concentration of petroleum ether phase was 17 mg/L for H.akashiwo.However,no significant algicidal effects were observed on the butanol phase and distilled water phase.These three macroalgae's culture medium filtrate exhibited no apparent growth inhibitory effect on the microalga under initial filtrate addition whereas the growth of H.akashiwo was significantly inhibited under semi-continuous filtrate addition,which suggests that continuous release of small quantities of rapidly degradable allelochemicals from the fresh tissue of both macroalgae was effective in inhibiting the growth of H.akashiwo.展开更多
文摘The simulation of a control system for the longitudinal axis of the rotary or fixed-wing unmanned aerial vehicles(UAVs)is demonstrated in this study.The control unit includes design considerations of two controllers to provide robust stability,tracking of the proposed linear dynamics,an adequate set of proportional-integral-derivative(PID)controller gains,and a minimal cost function.The PID control and linear quadratic regulator(LQR)with or without full-state-observer were evaluated.An optimal control system is assumed to provide fast rise and settling time,minimize overshoot,and eliminate the steady-state error.The effectiveness of this approach was verified by a linear model of the UAV aircraft in the semi-dynamic simulation platform of Matlab/Simulink,in which the open-loop system was assessed in terms of flight robustness and reference tracking.The experimental results show that the proposed controllers effectively improve the configuration of the control system of the plant,maintain the sustainability of the dynamic flight model stability,and diminish the flight controller errors.The LQR provides robust stability,but it is not optimal in the transient phase of particular plant output.The PID control system can adjust the controller’s gains for optimal hovering(or stable slow flight)and is especially useful for the tracking system.Finally,comparing aircraft stability using PID and LQR controllers shows that the latter has less overshoot and a shorter settling time;in addition,all proposed controllers can be practically deployed as one UAV’s system,which can be handled as an exemplary model of the UAV flight management system.
基金supported by the Thailand Research Fund through the Royal Golden Jubilee Ph.D.Program(PHD/0225/2561)the Faculty of Engineering,Kamphaeng Saen Campus,Kasetsart University,Thailand。
文摘The adulteration concentration of palm kernel oil(PKO)in virgin coconut oil(VCO)was quantified using near-infrared(NIR)hyperspectral imaging.Nowadays,some VCO is adulterated with lower-priced PKO to reduce production costs,which diminishes the quality of the VCO.This study used NIR hyperspectral imaging in the wavelength region 900-1,650 nm to create a quantitative model for the detection of PKO contaminants(0-100%)in VCO and to develop predictive mapping.The prediction equation for the adulteration of VCO with PKO was constructed using the partial least squares regression method.The best predictive model was pre-processed using the standard normal variate method,and the coefficient of determination of prediction was 0.991,the root mean square error of prediction was 2.93%,and the residual prediction deviation was 10.37.The results showed that this model could be applied for quantifying the adulteration concentration of PKO in VCO.The prediction adulteration concentration mapping of VCO with PKO was created from a calibration model that showed the color level according to the adulteration concentration in the range of 0-100%.NIR hyperspectral imaging could be clearly used to quantify the adulteration of VCO with a color level map that provides a quick,accurate,and non-destructive detection method.
文摘The necessity to saline and sodic waters is sometimes used for irrigating agricultural activities under certain circumstances, but it is important to note that the use of these waters comes with specific considerations and limitations. One way to decrease undesirable effects of sodic waters on the physical and chemical properties of soils is to apply organic and chemical amendments within the soil. This study aimed to assess the effectiveness of saline water on soil acidity, alkalinity and nutrients leaching in sandy loamy soil at Bella flower farm, in Rwamagana District, Rwanda. The water used was from the Muhazi Lake which is classified as Class I (Saline water quality). Column leaching experiments using treated soils were then conducted under saturated conditions. The soil under experimental was first analyzed for its textural classification, soil properties and is classified as sandy loamy soil. The t-test was taken at 1%, 5% and 10% levels of statistical significance compared to control soil. The results indicated that the application of saline water to soils caused an increase in some soil nutrients like increase of Phosphorus (P), Potassium (K<sup>+</sup>), Magnesium (Mg2<sup>+</sup>), Sulphur (S), CN ratio and Sodium (Na<sup>+</sup>) and decreased soil texture, physical and chemical properties and remained soil nutrients. Consequently, the intensive addition of saline water leachates to soil in PVC pipes led to decreased of soil EC through leaching and a raiser Soluble Sodium Percentage (SSP). The rate of saline water application affected the increase accumulation of SAR and Na% in the top soil layers. The study indicated that saline water is an inefficient amendment for sandy soil with saline water irrigation. The study recommends further studies with similar topic with saline water irrigation, as it accentuated the alkalinity levels.
文摘Mechanical properties of ukam, banana, sisal, coconut, hemp and e-glass fibre reinforced laminates were evaluated to assess the possibility of using it as new material in engineering applications. Samples were fabricated by the hand lay-up process (30:70 fibre and matrix ratio by weight) and the properties evaluated using the INSTRON material testing system. The mechanical properties were tested and showed that glass laminate has the maximum tensile strength of 63 MPa, bending strength of 0.5 MPa, compressive strength of 37.75 MPa and the impact strength of 17.82 J/m2. The ukam plant fibre laminate has the maximum tensile strength of 16.25 MPa and the impact strength of 9.8J/m among the natural fibres;the sisal laminate has the maximum compressive strength of 42 MPa and maximum bending strength of 0.0036 MPa among the natural fibres. Results indicated that natural fibres are of interest for low-cost engineering applications and can compete with artificial glass fibres (E-glass fibre) when a high stiffness per unit weight is desirable. Results also indicated that future research towards significant improvements in tensile and impact strength of these types of composites should focus on the optimisation of fibre strength rather than interfacial bond strength.
文摘The estuary tides affect groundwater dynamics;these areas are susceptible to waterlogging and salinity issues.A study was conducted on two fields with a total area of 60 hectares under a center pivot irrigation system that works with solar energy and belong to a commercial farm located in Northern Sudan.To monitor soil salinity and calcium carbonate in the area and stop future degradation of soil resources,easy,non-intrusive,and practical procedures are required.The objective of this study was to use remote sensing-determined Sentinel-2 satellite imagery using various soil indices to develop prediction models for the estimation of soil electrical conductivity(EC)and soil calcium carbonate(CaCO_(3)).Geo-referenced soil samples were collected from 72 locations and analyzed in the laboratory for soil EC and CaCO_(3).The electrical conductivity of the soil saturation paste extract was represented by average values in soil dataset samples from two fields collected from the topsoil layer(0 to 15 cm)characteristic of the local salinity gradient.The various soil indices,used in this study,were calculated from the Sentinel-2 satellite imagery.The prediction was determined using the root mean square error(RMSE)and cross validation was done using coefficient of determination.The results of regression analysis showed linear relationships with significant correlation between the EC analyzed in laboratory and the salinity index-2“SI2”(Model-1:R^(2)=0.59,p=0.00019 and root mean square error(RMSE=1.32%)and the bare soil index“BSI”(Model-2:R^(2)=0.63,p=0.00012 and RMSE=6.42%).Model-1 demonstrated the best model for predicting soil EC,and validation R^(2)and RMSE values of 0.48%and 1.32%,respectively.The regression analysis results for soil CaCO_(3)determination showed linear relationships with data obtained in laboratory and the bare soil index“BSI”(Model-3:R^(2)=0.45,p=0.00021 and RMSE=1.29%)and the bare soil index“BSI”&Normalized difference salinity index“NDSI”(Model-4:R^(2)=0.53,p=0.00015 and RMSE=1.55%).The validation confirmed the Model-3 results for prediction of soil CaCO_(3)with R^(2)and RMSE values of 0.478%and 1.29%,respectively.Future soil monitoring programs might consider the use of remote sensing data for assessing soil salinity and CaCO_(3)using soil indices results generated from satellite image(i.e.,Sentinel-2).
基金the Researchers Supporting Project No.(RSP2023R410)King Saud University,Riyadh,Saudi ArabiaPunjab Agricultural Research Board,Pakistan for funding the Research Project PARB No.904.
文摘Deficiencies of essential vitamins,iron(Fe),and zinc(Zn)affect over one-half of the world’s population.A significant progress has been made to control micronutrient deficiencies through supplementation,but new approaches are needed,especially to reach the rural poor.Agronomic biofortification of pulses with Zn,Fe,and boron(B)offers a pragmatic solution to combat hidden hunger instead of food fortification and supplementation.Moreover,it also has positive effects on crop production as well.Therefore,we conducted three separate field experiments for two consecutive years to evaluate the impact of soil and foliar application of the aforementioned nutrients on the yield and seed biofortification of mungbean.Soil application of Zn at 0,4.125,8.25,Fe at 0,2.5,5.0 and B at 0,0.55,1.1 kg ha−1 was done in the first,second and third experiment,respectively.Foliar application in these experiments was done at 0.3%Zn,0.2%Fe and 0.1%B respectively one week after flowering initiation.Data revealed that soil-applied Zn,Fe and B at 8.25,5.0 and 1.1 kg ha−1,respectively,enhanced the grain yield of mungbean;however,this increase in yield was statistically similar to that recorded with Zn,Fe and B at 4.125,2.5 and 0.55 kg ha−1,respectively.Foliar application of these nutrients at flower initiation significantly enhanced the Zn contents by 28%and 31%,Fe contents by 80%and 78%,while B contents by 98%and 116%over control during 2019 and 2020,respectively.It was concluded from the results that soil application of Zn,Fe,and B enhanced the yield performance of mungbean;while significant improvements in seed Zn,Fe,and B contents were recorded with foliar application of these nutrients.
基金the Researchers Supporting Project No.(RSP2023R410),King Saud University,Riyadh,Saudi Arabia.
文摘Nitrogen(N),the building block of plant proteins and enzymes,is an essential macronutrient for plant functions.A field experiment was conducted to investigate the impact of different N application rates(28,57,85,114,142,171,and 200 kg ha^(−1))on the performance of spring wheat(cv.Ujala-2016)during the 2017–2018 and 2018–2019 growing seasons.A control without N application was kept for comparison.Two years mean data showed optimum seed yield(5,461.3 kg ha^(−1))for N-application at 142 kg ha^(−1) whereas application of lower and higher rates of N did not result in significant and economically higher seed yield.A higher seed yield was obtained in the 2017–2018(5,595 kg ha^(−1))than in the 2018–2019(5,328 kg ha^(−1))growing seasons under an N application of 142 kg ha^(−1).It was attributed to the greater number of growing degree days in the first(1,942.35°C days)than in the second year(1,813.75°C).Higher rates of N(171 and 200 kg ha^(−1))than 142 kg ha^(−1) produced more number of tillers(i.e.,948,300 and 666,650 ha^(−1),respectively).However,this increase did not contribute in achieving higher yields.Application of 142,171,and 200 kg ha^(−1) resulted in 14.15%,15.0%and 15.35%grain protein concentrations in comparison to 13.15%with the application of 114 kg ha^(−1).It is concluded that the application of N at 142 kg ha^(−1) could be beneficial for attaining higher grain yields and protein concentrations of wheat cultivar Ujala-2016.
文摘Land suitability analysis of Moringa oleifera tree cultivation is important to enhance its product,as the demand forthis tree for medicinal values and food sources is increasing worldwide.Therefore,this study aimed to assess suitableland for Moringa oleifera tree cultivation by using the integration of multi-criteria evaluation with geospatialtechnologies in the Dhidhessa catchment,western Ethiopia.Five parameters,namely:slope,land use and landcover(LULC),soil texture,land surface temperature,and rainfall data,were used in this study.The land suitabilityevaluation of Moringa oleifera is classified into three classes as highly suitable,moderately suitable,and notsuitable.The results revealed that,about 344.4 km2(12.2%)of the area is categorized into highly suitable,and2343.7 km2(83%)is moderately suitable for Moringa tree,whereas,137.2 km2(4.9%)is categorized as notsuitable for Moringa oleifera tree cultivation.Hence,based on the finding of the study,we suggested that farmers andother stakeholders can cultivate Moringa oleifera trees in the Dhidhessa catchment.
基金The authors extend their appreciation to Researchers Supporting Project No.(RSP2023R298),King Saud University,Riyadh,Saudi Arabia.
文摘The availability of favorable genetic diversity is a thriving vitality for the success of a breeding program.It provides a firm basis of selecting superior breeding lines for the development of high yielding crop genotypes.In this context,present investigation aimed to generate information on genetic divergence and character association in a diversity panel of 123 local and exotic soybean genotypes.Analysis of variance revealed significant response of the evaluated genotypes based on studied attributes.It depicted the probability of selecting desirable soybean genotypes by focusing on character association studies and genetic diversity analysis.Correlation analysis revealed that seed yield per plant showed high positive correlation with 100-seed weight followed by pods per plant and plant height.Furthermore,path coefficient analysis exposed that pods per plant had maximum direct contribution in seed yield per plant followed by 100-seed weight,days to flowering and SPAD measurement.Genotype named“G-10”showed maximum yield per plant followed by 24607,G-52,24593,Arisoy,24566,17426,A-3127,24570 and 24567.Genetic diversity analysis grouped the evaluated germplasm into 17 clusters.All clusters showed zero intra-cluster variability;while inter-cluster divergence ranged from 9.00 to 91.11.Cluster V showed maximum inter-cluster distance with cluster XII followed by that of between V and VIII.Moreover,cluster IV with superior genotypes(G-10,24607,24593 and 24566),VI(17426 and 24567),XIII(24570)and X(Arisoy and G-52)showed above mean values for most of the studied characters.Overall,the results of hybridization between the superior genotypes of these cluster pairs might be useful for soybean breeding with improving agronomic traits and adaptability.
文摘The thrust of this research study was to ascertain the physicochemical characteristic in settling particulate matter and sediments of samples collected from the wellington industrial estate flood plains;the main of objectives are as follows: to determine the hydrogen ion index (pH) of the samples collected in the study area, to determine the electrical conductivity (EC) of the samples collected from the same location. Samples were collected from six locations (at varying depths of 0 - 5 cm and 5 - 10 cm) sample area 1 (Wellington Industrial Estate Area 1) WIEA1 WIEA 2, WIEA 3, WIEA 4, WIEA 5 and WIEA 6 and were given laboratory treatment. A laboratory thermometer was used to determine temperature of the samples when collected;(Dakton model) pH meter equipment and a Toledo electrical conductivity meter were used to determine the pH and EC respectively. The results indicated that the samples were acidic (low pH) and the conductivity of the samples was of medium and low range. This therefore expressed low levels of soluble metal ions in the environment that have effect on plants, animals and other organisms, agricultural and domestic activities in the environment under investigation. Hence bioconcentration and biomagnification are highly likely in these locations.
文摘Climate variability impacts on cocoa production are evaluated for the first time using 31 years (1979-2010) of data from SODEXAM (climate ground- based observations) and the ex-CAISTAB in three main cocoa production regions (Goh, Marahoué, and Haut-Sassandra) in the west-central part of Cote d’Ivoire. The work is a contribution to improving the quality of climate services dedicated to cocoa cultivation to ensure producers’ income and improve the yield of the production in the west-central part of Cote d’Ivoire. The results show that cocoa production is affected by the changes and variability in climate conditions (i.e. rainfall and temperature). In the Goh region, the increase in cocoa production seems to be mostly related to the augmentation of rainfall amount while in Marahoué, the increase in temperature is identified to have a more significant impact. Over the Haut-Sassandra region, both temperature and rainfall seem to have a considerable effect on the changes in cocoa production. The analysis based on linear regression by least-squares fit shows two characteristic modes (low and high-frequency variability) in the relationships between cocoa production and meteorological conditions suggesting a strong temporal signal impact related to the changes in the emblazoned surfaces. This leads to an important impact of the short-term variations of climate in cocoa production whereas, the influence of the long-term variability in climate on the cocoa yield seems marginal.
文摘Floods are phenomenon with significant socio-economic implications mainly for human loss, agriculture, livestock, soil loss and land degradation, for which many researchers try to identify the most appropriate methodologies by analyzing their temporal and spatial development. This study therefore attempts to employ the GIS-based multi-criteria decision analysis and analytical hierarchy process techniques to derive the flood risks management on rice productivity in the Gishari Agricultural Marshland in Rwamagana district, Rwanda. Here, six influencing potential factors to flooding, including river slope, soil texture, Land Use Land Cover through Land Sat 8, rainfall, river distance and Digital Elevation Model are considered for the delineation of flood risk zones. Data acquisition like Landsat 8 images, DEM, land use land cover, slope, and soil class in the study area were considered. Results showed that if the DEM is outdated or inaccurate due to changes in the terrain, such as construction, excavation, or erosion, the predicted flood patterns might not reflect the actual water flow. This could result unexpected flood extents and depths, potentially inundating rice fields that were not previously at risk and this, expectedly explained that the increase 1 m in elevation would reduce the rice productivity by 0.17% due to unplanned flood risks in marshland. It was found that the change in rainfall distribution in Gishari agricultural marshland would also decrease the rice productivity by 0.0018%, which is a sign that rainfall is a major factor of flooding in rice scheme. Rainfall distribution plays a crucial role in flooding analysis and can directly impact rice productivity. Oppositely, another causal factor was Land Use Land Cover (LULC), where the Multivariate Logistic Regression Model Analysis findings showed that the increase of one unit in Land Use Land Cover would increase rice productivity by 0.17% of the total rice productivity from the Gishari Agricultural Marshland. Based on findings from these techniques, the Gishari Agricultural Marshlands having steeped land with grassland is classified into five classes of flooding namely very low, low, moderate, high, and very high which include 430%, 361%, 292%, 223%, and 154%. Government of Rwanda and other implementing agencies and major key actors have to contribute on soil and water conservation strategies to reduce the runoff and soil erosion as major contributors of flooding.
基金supported by the National Natural Science Foundation of China (Grant no. 50675087 and Grant no. 50635030)the National Hi-tech Project (863 Project) (Grant no. SQ2008AA04ZX1478650)+3 种基金the Key Project of Science and Technology Research of Ministry of Education of China (Grant no. 106061)the National Key Technologies R&D Program (Grant no. 2006BAD11A08)the National Science Fund for Distinguished Young Scholars of China (Grant no. 50025516)the "985 Project" of Jilin University.
文摘The effects of biomimetic designs of tine furrow opener surface on equivalent pressure and pressure in the direction ofmotion on opener surface against soil were studied by finite element method (FEM) simulation and the effects of these designson tool force and power requirements were examined experimentally.Geometrical structures of the cuticle surfaces of dungbeetle (Copris ochus Motschulsky) were examined by stereoscopy.The structures of the cuticle surfaces and Ultra High Mo-lecular Weight Polyethylene (UHMWPE) material were modeled on surface of tine furrow opener as biomimetic designs.Sevenfurrow openers were analyzed in ANSYS program (a FEM simulation software).The biomimetic furrow opener surfaces withUHMWPE structures were found to have lower equivalent pressure and pressure in the direction of motion as compared to theconventional surface and to the biomimetic surfaces with textured steel-35 structures.It was found that the tool force and powerwere increased with the cutting depth and operating speed and the biomimetic furrow opener with UHMWPE tubular sectionridges showed the lowest resistance and power requirement against soil..
基金Project supported by the National Natural Science Foundation of China (No. 30370371) and the Natural Science Foundation of Zheji-ang Province (No. 301267), China
文摘The “Huang gua” melons were measured for their physical properties including firmness and static elastic modulus. The vibrational characteristics of fruits and vegetables are governed by their elastic modulus (firmness), mass, and geometry. Therefore, it is possible to evaluate firmness of fruits and vegetables based on their vibrational characteristics. Analysis of the vibration responses of a fruit is suggested for measuring elastic properties (Firmness) non-destructively. The impulse response method is often used to measure firmness of fruits. The fruit was excited using three types of balls (wooden, steel and rubber) and the vibration is detected by an accelerometer. The Instron device was used to measure the static elastic modulus of the inner, middle and outer portions of melon flesh. Finite element (FE) technique was used to determine the optimum excitation location of the chosen measurement sensor and to analyze the mode shape fruits. Four types of mode shapes (torsional or flexural mode shape, first-type, second-type spherical mode and breathing mode shape) were found. Finite element simulation results agreed well with experimental results. Correlation between the firmness and resonant frequency (r2=0.91) and between the resonant frequency and stiffness factor (r2=0.74) existed. The optimum location and suitable direction for excitation and response measurement on the fruit were suggested.
文摘The effect of external roof shading on the spatial distribution of air temperature and relative humidity in a greenhouse(Tin and RHin) was evaluated under the arid climatic conditions of Riyadh City, Saudi Arabia. Two identical, evaporatively-cooled, single-span greenhouses were used in the experiment. One greenhouse was externally shaded(Gs) using a movable black plastic net(30% transmissivity), and the other greenhouse was kept without shading(Gc). Strawberry plants were cultivated in both greenhouses. The results showed that the spatial distribution of the Tin and RHin was significantly affected by the outside solar radiation and evaporative cooling operation. The regression analysis showed that when the outside solar radiation intensity increased from 200 to 800 W m–2, the Tin increased by 4.5℃ in the Gc and 2℃in the Gs, while the RHin decreased by 15% in the Gc and 5% in the Gs, respectively. Compared with those in the Gc, more uniformity in the spatial distribution of the Tin and RHin was observed in the Gs. The difference between the maximum and minimum Tin of 6.4℃ and the RHin of 10% was lower in the Gs than those in the Gc during the early morning. Around 2℃ difference in the Tin was shown between the area closed to the exhausted fans and the area closed to the cooling pad with the external shading. In an evaporatively-cooled greenhouse in arid regions, the variation of the Tin and RHin in the vertical direction and along the sidewalls was much higher than that in the horizontal direction. The average variation of the Tin and RHin in the vertical direction was 5.2℃ and 10% in the Gc and 5.5℃ and 13% in the Gs, respectively. The external shading improved the spatial distribution of the Tin and RHin and improved the cooling efficiency of the evaporative cooling system by 12%, since the transmitted solar radiation and accumulated thermal energy in the greenhouse were significantly reduced.
文摘It is noted that any variation in operating conditions has a considerable effect on the tire/road interaction. Furthermore,choosing a range of proper values for carcass stiffness is very essential for both tire safety and effective driving action. In this work,an elaborated 3D model fully compliant with the geometrical size of radial tire 185/60 R15 is worked up, for evaluating the effects of components properties and working conditions on deformation and stress/strain fields created inside the tire. For the simulation, the tire structure is assumed to be composed of tread, carcass ply, and bead. The mechanical behavior of rubber as main component of tire is described by Mooney-Rivlin material model. The comparison of the obtained results and laboratory tests demonstrates the validity and high accuracy of analysis.
文摘The compaction and stress generation on terrain were always investigated based on empirical approaches or testing methods for tire/soil interaction.However,the analysis should be performed for various tires and at different soil strengths.With the increasing capacity of numerical computers and simulation software,finite element modeling of tire/terrain interaction seems a good approach for predicting the effect of change on the parameters.In this work,an elaborated 3D model fully complianning with the geometry of radial tire 115/60R13 was established,using commercial code Solidwork Simulation.The hyper-elastic and incompressible rubber as tire main material was analyzed by Moony-Rivlin model.The Drucker-Prager yield criterion was used to model the soil compaction.Results show that the model realistically predicts the laboratory tests outputs of the modeled tire on the soft soil.
文摘The goal of this investigation was to analyze the impact of some production variables (input) on agricultural pro- ductivity growth (output) in China from 1989～2002. We selected through random sampling Zhejiang Province for our disaggre- gate analysis with the use of Cobb-Douglas function. The estimation results showed that all key parameters are significant and are of the expected sign. Labor and that capital and land have positive impact on agricultural productivity growth.
基金The National Natural Science Foundation of China under contract No. 31070458the National Key Technology Support Program under contract No. 2010BAC68B00+4 种基金the Natural Science Foundation of Shandong Province under contract No.2009ZRB01461the Encouraging Foundation for Outstanding Youth Scientists of China under contract No. 2008BS09011the Science and Technology Project of Institutions of Higher Education of Shandong under contract No. J10LC13Special Grade of the Financial support from China Postdoctoral Science Foundation under contract No. 201003652Financial support from China Postdoctoral Science Foundation under contract No. 20090451350
文摘Allelopathic effects of several concentrations of fresh tissue,dry powder and dry tissue of three bloom-forming green macroalgae Ulva pertusa,Ulva linza and Enteromopha intestinalis on the red tide microalga Heterosigma akashiwo were evaluated in microcosms systems.The effects of macroalgae culture medium filtrate were investigated on H.akashiwo using initial or semi-continuous filtrate addition.Preliminary studies on the algicidal effects of one aqueous and four organic solvent extracts from the macroalgae on the microalga were carried out to confirm the existence of allelochemicals in the tissue of these macroalgae.The dry powder of U.pertusa was extracted with methanol,and the methanol extracts were partitioned to petroleum ether phase,ethyl acetate phase,butanol phase and distilled phase by liquid-liquid fractionation.The bioassays of the activity of every fraction were carried out on H.akashiwo.The resultant microcosms assay showed that the growth of H.akashiwo was strongly inhibited by using fresh tissues,dry powder or dry tissue of these three macroalgae,while aqueous and methanol extracts of both macroalgae had strong inhibitory effects on the growth of H.akashiwo,and the EC 50 values for methanol extract of U.pertusa,U.linza or E.intestinalis were 0.016,0.028×10-12 or 0.033×10-12,respectively.While the other three organic solvent extracts(acetone,ether and chloroform) had no apparent effect on its growth,this suggests that the allelochemicals from these three macroalgae had relatively high polarities.The activity of petroleum ether phase,ethyl acetate phase,butanol phase and distilled phase of U.pertusa methanol extract was carried out on H.akashiwo indicating that petroleum ether phase and ethyl acetate phase had stronger algicidal effect on H.akashiwo.The inhibition effect of the ethyl acetate phase was not as strong as that of petroleum ether phase,and effective concentration of petroleum ether phase was 17 mg/L for H.akashiwo.However,no significant algicidal effects were observed on the butanol phase and distilled water phase.These three macroalgae's culture medium filtrate exhibited no apparent growth inhibitory effect on the microalga under initial filtrate addition whereas the growth of H.akashiwo was significantly inhibited under semi-continuous filtrate addition,which suggests that continuous release of small quantities of rapidly degradable allelochemicals from the fresh tissue of both macroalgae was effective in inhibiting the growth of H.akashiwo.
