The design of a lightweight solar powered marine craft is considered in this report. Various design concepts were considered with respect to the hull type, resistance, aesthetics and the operating environment of the v...The design of a lightweight solar powered marine craft is considered in this report. Various design concepts were considered with respect to the hull type, resistance, aesthetics and the operating environment of the vessel. The planning hull-form catamaran was considered for the boat design. The resistance and other hydrodynamic characterization of boat were analyzed using the CAHI and Savitsky method. Detailed algorithm is developed for the sizing of the various components of the solar PV system for the boat. The hull resistance was found to be 740 N corresponding to the boat speed of 5?knot using the above stated methods. The motor power was obtained to be 2.239?kW (3 HP). Torqeedo outboard electric motor of 3?HP was selected for the boat propulsion. The battery bank was seized accordingly and four batteries of 235 AH and 12 V were selected for the storage of electric power for the boat propulsion. Hence, the solar PV module was sized. It was concluded that, due to the limited space for the installation of the PV module, additional source of power (land base) should be made available to completely charge the battery.展开更多
Ports and jetties complex operations come with various forms of pollutions. The analysis of marine pollution from ports becomes very necessary and complicated due to the various types of pollution, sources, effects an...Ports and jetties complex operations come with various forms of pollutions. The analysis of marine pollution from ports becomes very necessary and complicated due to the various types of pollution, sources, effects and different characteristics. The sources of environmental pollution other than ships and from industrial activities in port and jetties were critically looked at and analyzed. A complete review of the environmental pollution in ports and the tools to assess and minimize such negative environmental impact are analyzed. The instrument of questionnaires was employed and distributed among two seaports and one jetty;Onne, Okrika and Port Harcourt to collect respondents’ opinions on effects, sources and causes of marine pollution. The chi-square test for independence was used with 180 respondents from Onne port, Port Harcourt port and Okrika jetty. Water sample was collected from Onne seaport and pollution contents such as total petroleum hydrocarbon (TPH), bio-chemical oxygen demand (BOD), turbidity, pH and salinity were tested in the laboratory. The result shows that Onne water had a salinity level of 20,790 (mg/l) which under the salinity range of water is considered saline, a turbidity level of 4.00 (NTU) which was considered average comparing with a 5.00 (NTU) bench mark, BOD5 level of 0.48 (mg/l) which was considered pristine because most pristine seawater will have BOD below 1 (mg/l), pH level of 7.77 which falls under the range of sea water being alkaline (7.2 - 8.4), TPH level of 2.98 (mg/l) since all conditions of sampling and sample preservations were observed and the value is less than the DPR limit (10 mg/l). It was concluded that the activities in Onne port are within the acceptable limits. It was also observed from the questionnaire that a larger population of respondents in Onne, Okrika and Port Harcourt ports where conscious of the sources and effects of environmental pollution from their respective ports.展开更多
Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and f...Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and flow dynamics is essential to enhance operational performance and eliminate flow perturbations.Hence,the present research focuses on a numerical investigation of the impact of inclined slots with different angles installed at the side-wall of a cylindrical vessel equipped with a Rushton turbine.This study explores power consumption and vortex size while considering various rotation directions of the impeller with different rotation speeds.The numerical simulations are conducted for Reynolds numbers ranging from 104 to 105,using the RANS k-εturbulence model to govern the flow inside the stirred vessel,accounting for mass and momentum balances.The results have shown that the installation of slots reduces power consumption and vortex size compared to conventional vessel configu-rations.Moreover,increasing the slot angle from 0 to 32.5°further reduces energy consumption and vortex size,especially with negative rotation speeds.On the other hand,increasing the Reynolds numbers leads to a decrease in power consumption and an increase in vortex size.The present research therefore proposes a design for con-structing Rushton-turbine stirred vessels offering optimal operation,characterized by reduced energy consumption and minimized vortex size.展开更多
Ocean thermal energy conversion(OTEC)is a process of generating electricity by exploiting the temperature difference between warm surface seawater and cold deep seawater.Due to the high static and dynamic pressures th...Ocean thermal energy conversion(OTEC)is a process of generating electricity by exploiting the temperature difference between warm surface seawater and cold deep seawater.Due to the high static and dynamic pressures that are caused by seawater circulation,the stiffened panel that constitutes a seawater tank may undergo a reduction in ultimate strength.The current paper investigates the design of stiffening systems for OTEC seawater tanks by examining the effects of stiffening parameters such as stiffener sizes and span-over-bay ratio for the applied combined loadings of lateral and transverse pressure by fluid motion and axial compression due to global bending moment.The ultimate strength calculation was conducted by using the non-linear finite element method via the commercial software known as ABAQUS.The stress and deformation distribution due to pressure loads was computed in the first step and then brought to the second step,in which the axial compression was applied.The effects of pressure on the ultimate strength of the stiffener were investigated for representative stiffened panels,and the significance of the stiffener parameters was assessed by using the sensitivity analysis method.As a result,the ultimate strength was reduced by approximately 1.5%for the span-over-bay ratio of 3 and by 7%for the span-over-bay ratio of 6.展开更多
Conventional pipeline corrosion assessment methods result in failure pressure predictions that are conservative, especially for pipelines that are subjected to internal pressure and axial compressive stress. Alternati...Conventional pipeline corrosion assessment methods result in failure pressure predictions that are conservative, especially for pipelines that are subjected to internal pressure and axial compressive stress. Alternatively, numerical methods may be used. However, they are computationally expensive. This paper proposes an analytical equation based on finite element analysis (FEA) for failure pressure prediction of a high toughness corroded pipeline with a single corrosion defect subjected to internal pressure and axial compressive stress. The equations were developed based on the weights and biases of an Artificial Neural Network (ANN) model trained with failure pressure from finite element analysis (FEA) of a high toughness pipeline for various defect depths, defect lengths, and axial compressive stresses. The proposed model was validated against actual burst test results for high toughness materials and was found to be capable of making accurate predictions with a coefficient of determination (R<sup>2</sup>) of 0.99. An extensive parametric study using the proposed model was subsequently conducted to determine the effects of defect length, defect depth, and axial compressive stress on the failure pressure of a corroded pipe with a single defect. The application of ANN together with FEA has shown promising results in the development of an empirical solution for the failure pressure prediction of pipes with a single corrosion defect subjected to internal pressure and axial compressive stress.展开更多
This study sets up two new merit functions,which are minimized for the detection of real eigenvalue and complex eigenvalue to address nonlinear eigenvalue problems.For each eigen-parameter the vector variable is solve...This study sets up two new merit functions,which are minimized for the detection of real eigenvalue and complex eigenvalue to address nonlinear eigenvalue problems.For each eigen-parameter the vector variable is solved from a nonhomogeneous linear system obtained by reducing the number of eigen-equation one less,where one of the nonzero components of the eigenvector is normalized to the unit and moves the column containing that component to the right-hand side as a nonzero input vector.1D and 2D golden section search algorithms are employed to minimize the merit functions to locate real and complex eigenvalues.Simultaneously,the real and complex eigenvectors can be computed very accurately.A simpler approach to the nonlinear eigenvalue problems is proposed,which implements a normalization condition for the uniqueness of the eigenvector into the eigenequation directly.The real eigenvalues can be computed by the fictitious time integration method(FTIM),which saves computational costs compared to the one-dimensional golden section search algorithm(1D GSSA).The simpler method is also combined with the Newton iterationmethod,which is convergent very fast.All the proposed methods are easily programmed to compute the eigenvalue and eigenvector with high accuracy and efficiency.展开更多
Improving vehicle fuel consumption,performance and aerodynamic efficiency by drag reduction especially in heavy vehicles is one of the indispensable issues of automotive industry.In this work,the effects of adding app...Improving vehicle fuel consumption,performance and aerodynamic efficiency by drag reduction especially in heavy vehicles is one of the indispensable issues of automotive industry.In this work,the effects of adding append devices like deflector and cab vane corner on heavy commercial vehicle drag reduction were investigated.For this purpose,the vehicle body structure was modeled with various supplementary parts at the first stage.Then,computational fluid dynamic(CFD) analysis was utilized for each case to enhance the optimal aerodynamic structure at different longitudinal speeds for heavy commercial vehicles.The results show that the most effective supplementary part is deflector,and by adding this part,the drag coefficient is decreased considerably at an optimum angle.By adding two cab vane corners at both frontal edges of cab,a significant drag reduction is noticed.Back vanes and base flaps are simple plates which can be added at the top and side end of container and at the bottom with specific angle respectively to direct the flow and prevent the turbulence.Through the analysis of airflow and pressure distribution,the results reveal that the cab vane reduces fuel consumption and drag coefficient by up to 20 % receptively using proper deflector angle.Finally,by adding all supplementary parts at their optimized positions,41% drag reduction is obtained compared to the simple model.展开更多
The wear and corrosion resistance of Fe_(72.2)Cr_(16.8)Ni_(7.3)Mo_(1.6)Mn_(0.7)C_(0.2)Si_(1.2) and Fe_(77.3)Cr_(15.8)Ni_(3.9)Mo_(1.1)Mn_(0.5)C_(0.2)Si_(1.2) coatings laser-cladded on AISI 4130 steel were studied.The c...The wear and corrosion resistance of Fe_(72.2)Cr_(16.8)Ni_(7.3)Mo_(1.6)Mn_(0.7)C_(0.2)Si_(1.2) and Fe_(77.3)Cr_(15.8)Ni_(3.9)Mo_(1.1)Mn_(0.5)C_(0.2)Si_(1.2) coatings laser-cladded on AISI 4130 steel were studied.The coatings possess excellent wear and corrosion resistance despite the absence of expensive yttrium,tungsten,and cobalt and very little molybdenum.The microstructure mainly consists of dendrites and eutectic phases,such as duplex(γ+α)-Fe and the Fe–Cr(Ni)solid solution,confirmed via energy dispersive spectrometry and X-ray diffraction.The cladded Fe-based coatings have lower coefficients of friction,and narrower and shallower wear tracks than the substrate without the cladding,and the main wear mechanism is mild abrasive wear.Electrochemical test results suggest that the soft Fe_(72.2)Cr_(16.8)Ni_(7.3)Mo_(1.6)Mn_(0.7)C_(0.2)Si_(1.2) coating with high Cr and Ni concentrations has high passivation resistance,low corrosion current,and positive corrosion potential,providing a better protective barrier layer to the AISI 4130 steel against corrosion.展开更多
Improving rollover and stability of the vehicles is the indispensable part of automotive research to prevent vehicle rollover and crashes.The main objective of this work is to develop active control mechanism based on...Improving rollover and stability of the vehicles is the indispensable part of automotive research to prevent vehicle rollover and crashes.The main objective of this work is to develop active control mechanism based on fuzzy logic controller(FLC) and linear quadratic regulator(LQR) for improving vehicle path following,roll and handling performances simultaneously.3-DOF vehicle model including yaw rate,lateral velocity(lateral dynamic) and roll angle(roll dynamic) were developed.The controller produces optimal moment to increase stability and roll margin of vehicle by receiving the steering angle as an input and vehicle variables as a feedback signal.The effectiveness of proposed controller and vehicle model were evaluated during fishhook and single lane-change maneuvers.Simulation results demonstrate that in both cases(FLC and LQR controllers) by reducing roll angle,lateral acceleration and side slip angles remain under 0.6g and 4° during maneuver,which ensures vehicle stability and handling properties.Finally,the sensitivity and robustness analysis of developed controller for varying longitudinal speeds were investigated.展开更多
High-thermal conductivity enhancement of nanofluid is one of the promising topics of the nanoscience research field. This work reports the experimental study on the preparation of graphene(GN) and multi-walled carbon ...High-thermal conductivity enhancement of nanofluid is one of the promising topics of the nanoscience research field. This work reports the experimental study on the preparation of graphene(GN) and multi-walled carbon nanotubes(MWCNTs) based nanofluids with the assistance of sodium dodecyl benzene sulfonate(SDBS) and sodium dodecyl sulfate(SDS) surfactants, and their thermal behaviors. The present work suggests not a solution, but a solution approach and deduces a new conclusion by trying to resolve the agglomeration problem and improve the dispersibility of nanoparticles in the base fluid. The analysis results of FESEM, thermal conductivity, diffusivity, effusivity and heat transfer coefficient enhancement ratio of nanofluid with surfactants SDS and SDBS expose strong evidence of the dispersing effect of surfactant on the making of nanofluid.展开更多
The aim of this research is to develop an algorithm and application that can perform real-time monitoring of the safety operation of offshore platforms and subsea gas pipelines as well as determine the need for ship i...The aim of this research is to develop an algorithm and application that can perform real-time monitoring of the safety operation of offshore platforms and subsea gas pipelines as well as determine the need for ship inspection using data obtained from automatic identification system(AIS).The research also focuses on the integration of shipping database,AIS data,and others to develop a prototype for designing a real-time monitoring system of offshore platforms and pipelines.A simple concept is used in the development of this prototype,which is achieved by using an overlaying map that outlines the coordinates of the offshore platform and subsea gas pipeline with the ship’s coordinates(longitude/latitude)as detected by AIS.Using such information,we can then build an early warning system(EWS)relayed through short message service(SMS),email,or other means when the ship enters the restricted and exclusion zone of platforms and pipelines.The ship inspection system is developed by combining several attributes.Then,decision analysis software is employed to prioritize the vessel’s four attributes,including ship age,ship type,classification,and flag state.Results show that the EWS can increase the safety level of offshore platforms and pipelines,as well as the efficient use of patrol boats in monitoring the safety of the facilities.Meanwhile,ship inspection enables the port to prioritize the ship to be inspected in accordance with the priority ranking inspection score.展开更多
The synthesis of new materials containing multi-walled carbon nanotubes (MWCNTs) and the microstructure of alumina particles were investigated and characterized. The MWCNTs and alumina particles were ground under both...The synthesis of new materials containing multi-walled carbon nanotubes (MWCNTs) and the microstructure of alumina particles were investigated and characterized. The MWCNTs and alumina particles were ground under both the dry and wet conditions with various rotation speeds (200 - 400 r/min) in planetary ball milling machine, and their combination characteristics were described. The experimental results were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM) and particle sizing analysis (PSA). SEM result revealed that the combination of MWCNTs - Alumina particles mixed quite well under both the dry and wet grinding with rotation speed of 400 r/min. XRD characterization indicated the better result could get in ground samples at a rotation speed of 400 r/min. PSA result showed the particle size decreased with increase the grinding speeds. From the overall results, we observed that the grinding method can be used to synthesize new material with high efficiency.展开更多
The paper studies the dispersion of axisymmetric longitudinal waves in the bi-material compound circular cylinder made of linear viscoelastic materials.The investigations are carried out within the scope of the piecew...The paper studies the dispersion of axisymmetric longitudinal waves in the bi-material compound circular cylinder made of linear viscoelastic materials.The investigations are carried out within the scope of the piecewise homogeneous body model by utilizing the exact equations of linear viscoelasto-dynamics.The corresponding dispersion equation is derived for an arbitrary type of hereditary operator and the algorithm is developed for its numerical solution.Concrete numerical results are obtained for the case where the relations of the constituents of the cylinder are described through fractional exponential operators.The influence of the viscosity of the materials of the compound cylinder on the wave dispersion is studied through the rheological parameters which indicate the characteristic creep time and long-term values of the elastic constants of these materials.Dispersion curves are presented for certain selected dispersive and non-dispersive attenuation cases under various values of the problem parameters and the influence of the aforementioned rheological parameters on these curves is discussed.As a result of the numerical investigations,in particular,it is established that in the case where the rheological parameters of the components of the compound cylinder are the same,the viscosity of the layers’materials causes the axisymmetric wave propagation velocity to decrease.展开更多
In this study, we optimize the loading and discharging operations of the Liquefied Natural Gas(LNG) carrier. First, we identify the required precautions for LNG carrier cargo operations. Next, we prioritize these prec...In this study, we optimize the loading and discharging operations of the Liquefied Natural Gas(LNG) carrier. First, we identify the required precautions for LNG carrier cargo operations. Next, we prioritize these precautions using the analytic hierarchy process(AHP) and experts' judgments, in order to optimize the operational loading and discharging exercises of the LNG carrier, prevent system failure and human error, and reduce the risk of marine accidents. Thus, the objective of our study is to increase the level of safety during cargo operations.展开更多
Environmentally assisted cracking(EAC)behavior of two Mg-rare earth(RE)alloys such as Mg-Zn-Gd-Nd-Zr(EV31A)and Mg-Y-Nd(WE43C)alloys was investigated by using U-bend specimens.Open circuit potentials(OCP)of the U-bend ...Environmentally assisted cracking(EAC)behavior of two Mg-rare earth(RE)alloys such as Mg-Zn-Gd-Nd-Zr(EV31A)and Mg-Y-Nd(WE43C)alloys was investigated by using U-bend specimens.Open circuit potentials(OCP)of the U-bend specimens were monitored during the EAC tests in 0.1 M NaOH solution with different chloride concentrations at room temperature.EV31A(as-received,and peak aged)and WE43C(peak aged)specimens failed by SCC in 80 ppm chloride containing 0.1 M NaOH solution at OCP.When the EAC initiation occurred,the OCP decreased continuously.Irregular fluctuations of the OCP were observed in the absence of EAC.The OCP versus time profile could be used for monitoring EAC failure of the Mg-RE alloy components in real life service.Applied potentials did not cause cracking of the EV31A alloy in 80 ppm Cl-containing 0.1 M NaOH.Accelerated cracking was observed on the WE43C alloy in peak-aged condition under the applied potentials in the transpassive region when compared to that of OCP condition.Overaging decreased the susceptibility to cracking.展开更多
The driving necessities of cost reduction and the need to develop fields at ever increasing water depths have led to the use of floating structures. Among these structures are the Floating Production Storage and Offlo...The driving necessities of cost reduction and the need to develop fields at ever increasing water depths have led to the use of floating structures. Among these structures are the Floating Production Storage and Offloading (FPSO) units whose motion analysis is considered in this paper. In actual environmental condition, it is required to accurately determine or predict large amplitude motion of the FPSO before any offshore operation. This paper seeks to present a detailed method of computing the Response Amplitude Operator(s) (RAOs) for the six (6) degrees of freedom using ANSYS AQWA. The results indicate for Heave motion a tendency for the heave peak value to move slightly higher dimensionless encounter-frequency as the wave moves from Head sea to Beam sea direction. A MATLAB source code was developed to validate the result for heave motion at head sea. Although a small difference in predicted heave motion occurred, it is pertinent to note that the comparisons between results generated in the MATLAB program and ANSYS AQWA demonstrate generally good agreement, and the roll response of the FPSO is noted to be critical.展开更多
A proper characterization of catamarans performance in relation to demi-hull separation ratio (Sc/L) is imperative for optimal design and applications. Resistance, propulsion and good sea-keeping characteristics for v...A proper characterization of catamarans performance in relation to demi-hull separation ratio (Sc/L) is imperative for optimal design and applications. Resistance, propulsion and good sea-keeping characteristics for various demi-hull separation ratios at different operating conditions are prime considerations. This work evaluates the Resistance and Propulsion (RAP) characteristics of a 72 m long catamaran for various values of Sc/L (0.3, 0.4 and 0.5). Both physical models and numerical methods are implemented for the analysis. The analysis shows that the frictional resistance (RF) of catamaran is parabolic and slightly higher than those of monohulls. However, catamarans have superior sea-keeping performance. The RF of catamaran dominates the total resistance (RT) at low speeds;however, at high Froude number (Fn > 0.25), wave-making resistance (Rw) becomes dominant, especially during humps. Consequently, the RT-curve and the effective power PE-curve oscillate in rhythm with the Rw-curve as the velocity increases. Again, the effect of residuary resistance interference due to demi-hulls separation ratio is marginal, except during humps. Also, four speed-regimes are identified such as: 1) Low-speed (Fn st hump (0.23 nd hump, high-speed (Fn > 0.60). The catamaran PE for Fn > 0.6 is very high and uneconomical. Therefore, for optimal performance, catamarans should have service speed limits not exceeding Fn = 0.6.展开更多
This paper investigates the effects of site based parameters such as ambient temperature, humidity, altitude and heat transfer characteristic of a dual pressure heat recovery system on the performance of the combined ...This paper investigates the effects of site based parameters such as ambient temperature, humidity, altitude and heat transfer characteristic of a dual pressure heat recovery system on the performance of the combined cycle power plant within an equatorial environment. The bulk heat utilization and configuration of a dual pressure heat recovery system are investigated. It is observed that the heat system configuration play a vital role in optimizing the combined cycle overall performance, which has proportionality relationship with the operating ambient temperature and relative humidity of the gas turbine. The investigation is carried out within the ambient temperature range of 24℃ to 35℃, relative humidity of 60% to 80%, and a high level steam pressure of 60 bar to 110 bar. The results show that at 24℃ ambient temperature, the heat recovery system has the highest duty of 239.4 MW, the optimum combined cycle power output of 205.52 MW, and overall efficiency of 47.46%. It further indicates that as the ambient temperature increases at an average exhaust gas temperature of 530℃ and mass flow of 470 kg/s, the combined cycle power output and efficiency decrease by 15.5% and 13.7% respectively under the various considerations. This results from a drop in the air and exhaust mass flow as the values of the site parameters increase. The overall results indicate that decreasing the ambient temperature at optimum exhaust gas flow and temperature increases the heat recovery system heat duty performance, the steam generation, overall combined cycle power output and efficiency, which satisfies the research objective.展开更多
文摘The design of a lightweight solar powered marine craft is considered in this report. Various design concepts were considered with respect to the hull type, resistance, aesthetics and the operating environment of the vessel. The planning hull-form catamaran was considered for the boat design. The resistance and other hydrodynamic characterization of boat were analyzed using the CAHI and Savitsky method. Detailed algorithm is developed for the sizing of the various components of the solar PV system for the boat. The hull resistance was found to be 740 N corresponding to the boat speed of 5?knot using the above stated methods. The motor power was obtained to be 2.239?kW (3 HP). Torqeedo outboard electric motor of 3?HP was selected for the boat propulsion. The battery bank was seized accordingly and four batteries of 235 AH and 12 V were selected for the storage of electric power for the boat propulsion. Hence, the solar PV module was sized. It was concluded that, due to the limited space for the installation of the PV module, additional source of power (land base) should be made available to completely charge the battery.
文摘Ports and jetties complex operations come with various forms of pollutions. The analysis of marine pollution from ports becomes very necessary and complicated due to the various types of pollution, sources, effects and different characteristics. The sources of environmental pollution other than ships and from industrial activities in port and jetties were critically looked at and analyzed. A complete review of the environmental pollution in ports and the tools to assess and minimize such negative environmental impact are analyzed. The instrument of questionnaires was employed and distributed among two seaports and one jetty;Onne, Okrika and Port Harcourt to collect respondents’ opinions on effects, sources and causes of marine pollution. The chi-square test for independence was used with 180 respondents from Onne port, Port Harcourt port and Okrika jetty. Water sample was collected from Onne seaport and pollution contents such as total petroleum hydrocarbon (TPH), bio-chemical oxygen demand (BOD), turbidity, pH and salinity were tested in the laboratory. The result shows that Onne water had a salinity level of 20,790 (mg/l) which under the salinity range of water is considered saline, a turbidity level of 4.00 (NTU) which was considered average comparing with a 5.00 (NTU) bench mark, BOD5 level of 0.48 (mg/l) which was considered pristine because most pristine seawater will have BOD below 1 (mg/l), pH level of 7.77 which falls under the range of sea water being alkaline (7.2 - 8.4), TPH level of 2.98 (mg/l) since all conditions of sampling and sample preservations were observed and the value is less than the DPR limit (10 mg/l). It was concluded that the activities in Onne port are within the acceptable limits. It was also observed from the questionnaire that a larger population of respondents in Onne, Okrika and Port Harcourt ports where conscious of the sources and effects of environmental pollution from their respective ports.
文摘Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and flow dynamics is essential to enhance operational performance and eliminate flow perturbations.Hence,the present research focuses on a numerical investigation of the impact of inclined slots with different angles installed at the side-wall of a cylindrical vessel equipped with a Rushton turbine.This study explores power consumption and vortex size while considering various rotation directions of the impeller with different rotation speeds.The numerical simulations are conducted for Reynolds numbers ranging from 104 to 105,using the RANS k-εturbulence model to govern the flow inside the stirred vessel,accounting for mass and momentum balances.The results have shown that the installation of slots reduces power consumption and vortex size compared to conventional vessel configu-rations.Moreover,increasing the slot angle from 0 to 32.5°further reduces energy consumption and vortex size,especially with negative rotation speeds.On the other hand,increasing the Reynolds numbers leads to a decrease in power consumption and an increase in vortex size.The present research therefore proposes a design for con-structing Rushton-turbine stirred vessels offering optimal operation,characterized by reduced energy consumption and minimized vortex size.
基金part of the OTEC research activity"Preliminary Design of a 5 MW OTEC plant:Study case in the North Bali"research grand DIPA-124.01.1.690505/2023 conducted by the Marine Renewable Energy Conversion Technology research group,Research Center for Hydrodynamics Technology,National Research and Innovation Agency(BRIN)。
文摘Ocean thermal energy conversion(OTEC)is a process of generating electricity by exploiting the temperature difference between warm surface seawater and cold deep seawater.Due to the high static and dynamic pressures that are caused by seawater circulation,the stiffened panel that constitutes a seawater tank may undergo a reduction in ultimate strength.The current paper investigates the design of stiffening systems for OTEC seawater tanks by examining the effects of stiffening parameters such as stiffener sizes and span-over-bay ratio for the applied combined loadings of lateral and transverse pressure by fluid motion and axial compression due to global bending moment.The ultimate strength calculation was conducted by using the non-linear finite element method via the commercial software known as ABAQUS.The stress and deformation distribution due to pressure loads was computed in the first step and then brought to the second step,in which the axial compression was applied.The effects of pressure on the ultimate strength of the stiffener were investigated for representative stiffened panels,and the significance of the stiffener parameters was assessed by using the sensitivity analysis method.As a result,the ultimate strength was reduced by approximately 1.5%for the span-over-bay ratio of 3 and by 7%for the span-over-bay ratio of 6.
文摘Conventional pipeline corrosion assessment methods result in failure pressure predictions that are conservative, especially for pipelines that are subjected to internal pressure and axial compressive stress. Alternatively, numerical methods may be used. However, they are computationally expensive. This paper proposes an analytical equation based on finite element analysis (FEA) for failure pressure prediction of a high toughness corroded pipeline with a single corrosion defect subjected to internal pressure and axial compressive stress. The equations were developed based on the weights and biases of an Artificial Neural Network (ANN) model trained with failure pressure from finite element analysis (FEA) of a high toughness pipeline for various defect depths, defect lengths, and axial compressive stresses. The proposed model was validated against actual burst test results for high toughness materials and was found to be capable of making accurate predictions with a coefficient of determination (R<sup>2</sup>) of 0.99. An extensive parametric study using the proposed model was subsequently conducted to determine the effects of defect length, defect depth, and axial compressive stress on the failure pressure of a corroded pipe with a single defect. The application of ANN together with FEA has shown promising results in the development of an empirical solution for the failure pressure prediction of pipes with a single corrosion defect subjected to internal pressure and axial compressive stress.
基金the National Science and Tech-nology Council,Taiwan for their financial support(Grant Number NSTC 111-2221-E-019-048).
文摘This study sets up two new merit functions,which are minimized for the detection of real eigenvalue and complex eigenvalue to address nonlinear eigenvalue problems.For each eigen-parameter the vector variable is solved from a nonhomogeneous linear system obtained by reducing the number of eigen-equation one less,where one of the nonzero components of the eigenvector is normalized to the unit and moves the column containing that component to the right-hand side as a nonzero input vector.1D and 2D golden section search algorithms are employed to minimize the merit functions to locate real and complex eigenvalues.Simultaneously,the real and complex eigenvectors can be computed very accurately.A simpler approach to the nonlinear eigenvalue problems is proposed,which implements a normalization condition for the uniqueness of the eigenvector into the eigenequation directly.The real eigenvalues can be computed by the fictitious time integration method(FTIM),which saves computational costs compared to the one-dimensional golden section search algorithm(1D GSSA).The simpler method is also combined with the Newton iterationmethod,which is convergent very fast.All the proposed methods are easily programmed to compute the eigenvalue and eigenvector with high accuracy and efficiency.
文摘Improving vehicle fuel consumption,performance and aerodynamic efficiency by drag reduction especially in heavy vehicles is one of the indispensable issues of automotive industry.In this work,the effects of adding append devices like deflector and cab vane corner on heavy commercial vehicle drag reduction were investigated.For this purpose,the vehicle body structure was modeled with various supplementary parts at the first stage.Then,computational fluid dynamic(CFD) analysis was utilized for each case to enhance the optimal aerodynamic structure at different longitudinal speeds for heavy commercial vehicles.The results show that the most effective supplementary part is deflector,and by adding this part,the drag coefficient is decreased considerably at an optimum angle.By adding two cab vane corners at both frontal edges of cab,a significant drag reduction is noticed.Back vanes and base flaps are simple plates which can be added at the top and side end of container and at the bottom with specific angle respectively to direct the flow and prevent the turbulence.Through the analysis of airflow and pressure distribution,the results reveal that the cab vane reduces fuel consumption and drag coefficient by up to 20 % receptively using proper deflector angle.Finally,by adding all supplementary parts at their optimized positions,41% drag reduction is obtained compared to the simple model.
基金financially supported by the Ocean Public Science and Technology Research Fund Projects of China (No. 201405013-3)the Science & Technology Program of Shanghai Maritime University (No. 20130448)+1 种基金the China Postdoctoral Science Foundation (No. 2017M620153)the National Natural Science Foundation of China (No. 51609133)
文摘The wear and corrosion resistance of Fe_(72.2)Cr_(16.8)Ni_(7.3)Mo_(1.6)Mn_(0.7)C_(0.2)Si_(1.2) and Fe_(77.3)Cr_(15.8)Ni_(3.9)Mo_(1.1)Mn_(0.5)C_(0.2)Si_(1.2) coatings laser-cladded on AISI 4130 steel were studied.The coatings possess excellent wear and corrosion resistance despite the absence of expensive yttrium,tungsten,and cobalt and very little molybdenum.The microstructure mainly consists of dendrites and eutectic phases,such as duplex(γ+α)-Fe and the Fe–Cr(Ni)solid solution,confirmed via energy dispersive spectrometry and X-ray diffraction.The cladded Fe-based coatings have lower coefficients of friction,and narrower and shallower wear tracks than the substrate without the cladding,and the main wear mechanism is mild abrasive wear.Electrochemical test results suggest that the soft Fe_(72.2)Cr_(16.8)Ni_(7.3)Mo_(1.6)Mn_(0.7)C_(0.2)Si_(1.2) coating with high Cr and Ni concentrations has high passivation resistance,low corrosion current,and positive corrosion potential,providing a better protective barrier layer to the AISI 4130 steel against corrosion.
文摘Improving rollover and stability of the vehicles is the indispensable part of automotive research to prevent vehicle rollover and crashes.The main objective of this work is to develop active control mechanism based on fuzzy logic controller(FLC) and linear quadratic regulator(LQR) for improving vehicle path following,roll and handling performances simultaneously.3-DOF vehicle model including yaw rate,lateral velocity(lateral dynamic) and roll angle(roll dynamic) were developed.The controller produces optimal moment to increase stability and roll margin of vehicle by receiving the steering angle as an input and vehicle variables as a feedback signal.The effectiveness of proposed controller and vehicle model were evaluated during fishhook and single lane-change maneuvers.Simulation results demonstrate that in both cases(FLC and LQR controllers) by reducing roll angle,lateral acceleration and side slip angles remain under 0.6g and 4° during maneuver,which ensures vehicle stability and handling properties.Finally,the sensitivity and robustness analysis of developed controller for varying longitudinal speeds were investigated.
基金Project(NRF-2014R1A1A4A03005148)supported by Basic Science Research Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Education,Science and Technology,Korea
文摘High-thermal conductivity enhancement of nanofluid is one of the promising topics of the nanoscience research field. This work reports the experimental study on the preparation of graphene(GN) and multi-walled carbon nanotubes(MWCNTs) based nanofluids with the assistance of sodium dodecyl benzene sulfonate(SDBS) and sodium dodecyl sulfate(SDS) surfactants, and their thermal behaviors. The present work suggests not a solution, but a solution approach and deduces a new conclusion by trying to resolve the agglomeration problem and improve the dispersibility of nanoparticles in the base fluid. The analysis results of FESEM, thermal conductivity, diffusivity, effusivity and heat transfer coefficient enhancement ratio of nanofluid with surfactants SDS and SDBS expose strong evidence of the dispersing effect of surfactant on the making of nanofluid.
文摘The aim of this research is to develop an algorithm and application that can perform real-time monitoring of the safety operation of offshore platforms and subsea gas pipelines as well as determine the need for ship inspection using data obtained from automatic identification system(AIS).The research also focuses on the integration of shipping database,AIS data,and others to develop a prototype for designing a real-time monitoring system of offshore platforms and pipelines.A simple concept is used in the development of this prototype,which is achieved by using an overlaying map that outlines the coordinates of the offshore platform and subsea gas pipeline with the ship’s coordinates(longitude/latitude)as detected by AIS.Using such information,we can then build an early warning system(EWS)relayed through short message service(SMS),email,or other means when the ship enters the restricted and exclusion zone of platforms and pipelines.The ship inspection system is developed by combining several attributes.Then,decision analysis software is employed to prioritize the vessel’s four attributes,including ship age,ship type,classification,and flag state.Results show that the EWS can increase the safety level of offshore platforms and pipelines,as well as the efficient use of patrol boats in monitoring the safety of the facilities.Meanwhile,ship inspection enables the port to prioritize the ship to be inspected in accordance with the priority ranking inspection score.
基金Funded by the Basic Science Program through the National Research Foundation of Korea (NRF) by the Ministry of Education, Science and Technology (No.2012-0004544)
文摘The synthesis of new materials containing multi-walled carbon nanotubes (MWCNTs) and the microstructure of alumina particles were investigated and characterized. The MWCNTs and alumina particles were ground under both the dry and wet conditions with various rotation speeds (200 - 400 r/min) in planetary ball milling machine, and their combination characteristics were described. The experimental results were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM) and particle sizing analysis (PSA). SEM result revealed that the combination of MWCNTs - Alumina particles mixed quite well under both the dry and wet grinding with rotation speed of 400 r/min. XRD characterization indicated the better result could get in ground samples at a rotation speed of 400 r/min. PSA result showed the particle size decreased with increase the grinding speeds. From the overall results, we observed that the grinding method can be used to synthesize new material with high efficiency.
文摘The paper studies the dispersion of axisymmetric longitudinal waves in the bi-material compound circular cylinder made of linear viscoelastic materials.The investigations are carried out within the scope of the piecewise homogeneous body model by utilizing the exact equations of linear viscoelasto-dynamics.The corresponding dispersion equation is derived for an arbitrary type of hereditary operator and the algorithm is developed for its numerical solution.Concrete numerical results are obtained for the case where the relations of the constituents of the cylinder are described through fractional exponential operators.The influence of the viscosity of the materials of the compound cylinder on the wave dispersion is studied through the rheological parameters which indicate the characteristic creep time and long-term values of the elastic constants of these materials.Dispersion curves are presented for certain selected dispersive and non-dispersive attenuation cases under various values of the problem parameters and the influence of the aforementioned rheological parameters on these curves is discussed.As a result of the numerical investigations,in particular,it is established that in the case where the rheological parameters of the components of the compound cylinder are the same,the viscosity of the layers’materials causes the axisymmetric wave propagation velocity to decrease.
文摘In this study, we optimize the loading and discharging operations of the Liquefied Natural Gas(LNG) carrier. First, we identify the required precautions for LNG carrier cargo operations. Next, we prioritize these precautions using the analytic hierarchy process(AHP) and experts' judgments, in order to optimize the operational loading and discharging exercises of the LNG carrier, prevent system failure and human error, and reduce the risk of marine accidents. Thus, the objective of our study is to increase the level of safety during cargo operations.
基金J.Ninlachart acknowledges the support by Royal Thai Navy.Mg-RE alloys investigated in this study were donated by Magnesium Elektron N.A.Inc.
文摘Environmentally assisted cracking(EAC)behavior of two Mg-rare earth(RE)alloys such as Mg-Zn-Gd-Nd-Zr(EV31A)and Mg-Y-Nd(WE43C)alloys was investigated by using U-bend specimens.Open circuit potentials(OCP)of the U-bend specimens were monitored during the EAC tests in 0.1 M NaOH solution with different chloride concentrations at room temperature.EV31A(as-received,and peak aged)and WE43C(peak aged)specimens failed by SCC in 80 ppm chloride containing 0.1 M NaOH solution at OCP.When the EAC initiation occurred,the OCP decreased continuously.Irregular fluctuations of the OCP were observed in the absence of EAC.The OCP versus time profile could be used for monitoring EAC failure of the Mg-RE alloy components in real life service.Applied potentials did not cause cracking of the EV31A alloy in 80 ppm Cl-containing 0.1 M NaOH.Accelerated cracking was observed on the WE43C alloy in peak-aged condition under the applied potentials in the transpassive region when compared to that of OCP condition.Overaging decreased the susceptibility to cracking.
文摘The driving necessities of cost reduction and the need to develop fields at ever increasing water depths have led to the use of floating structures. Among these structures are the Floating Production Storage and Offloading (FPSO) units whose motion analysis is considered in this paper. In actual environmental condition, it is required to accurately determine or predict large amplitude motion of the FPSO before any offshore operation. This paper seeks to present a detailed method of computing the Response Amplitude Operator(s) (RAOs) for the six (6) degrees of freedom using ANSYS AQWA. The results indicate for Heave motion a tendency for the heave peak value to move slightly higher dimensionless encounter-frequency as the wave moves from Head sea to Beam sea direction. A MATLAB source code was developed to validate the result for heave motion at head sea. Although a small difference in predicted heave motion occurred, it is pertinent to note that the comparisons between results generated in the MATLAB program and ANSYS AQWA demonstrate generally good agreement, and the roll response of the FPSO is noted to be critical.
文摘A proper characterization of catamarans performance in relation to demi-hull separation ratio (Sc/L) is imperative for optimal design and applications. Resistance, propulsion and good sea-keeping characteristics for various demi-hull separation ratios at different operating conditions are prime considerations. This work evaluates the Resistance and Propulsion (RAP) characteristics of a 72 m long catamaran for various values of Sc/L (0.3, 0.4 and 0.5). Both physical models and numerical methods are implemented for the analysis. The analysis shows that the frictional resistance (RF) of catamaran is parabolic and slightly higher than those of monohulls. However, catamarans have superior sea-keeping performance. The RF of catamaran dominates the total resistance (RT) at low speeds;however, at high Froude number (Fn > 0.25), wave-making resistance (Rw) becomes dominant, especially during humps. Consequently, the RT-curve and the effective power PE-curve oscillate in rhythm with the Rw-curve as the velocity increases. Again, the effect of residuary resistance interference due to demi-hulls separation ratio is marginal, except during humps. Also, four speed-regimes are identified such as: 1) Low-speed (Fn st hump (0.23 nd hump, high-speed (Fn > 0.60). The catamaran PE for Fn > 0.6 is very high and uneconomical. Therefore, for optimal performance, catamarans should have service speed limits not exceeding Fn = 0.6.
文摘This paper investigates the effects of site based parameters such as ambient temperature, humidity, altitude and heat transfer characteristic of a dual pressure heat recovery system on the performance of the combined cycle power plant within an equatorial environment. The bulk heat utilization and configuration of a dual pressure heat recovery system are investigated. It is observed that the heat system configuration play a vital role in optimizing the combined cycle overall performance, which has proportionality relationship with the operating ambient temperature and relative humidity of the gas turbine. The investigation is carried out within the ambient temperature range of 24℃ to 35℃, relative humidity of 60% to 80%, and a high level steam pressure of 60 bar to 110 bar. The results show that at 24℃ ambient temperature, the heat recovery system has the highest duty of 239.4 MW, the optimum combined cycle power output of 205.52 MW, and overall efficiency of 47.46%. It further indicates that as the ambient temperature increases at an average exhaust gas temperature of 530℃ and mass flow of 470 kg/s, the combined cycle power output and efficiency decrease by 15.5% and 13.7% respectively under the various considerations. This results from a drop in the air and exhaust mass flow as the values of the site parameters increase. The overall results indicate that decreasing the ambient temperature at optimum exhaust gas flow and temperature increases the heat recovery system heat duty performance, the steam generation, overall combined cycle power output and efficiency, which satisfies the research objective.
