This study is an extension of the previous work done with ARS-680 Environmental Chamber. Drying is a complex operation that demands much energy and time. Drying is essentially important for preservation of ginger rhiz...This study is an extension of the previous work done with ARS-680 Environmental Chamber. Drying is a complex operation that demands much energy and time. Drying is essentially important for preservation of ginger rhizome. Drying of ginger was modeled, and then the effective diffusion coefficient and activation energy were determined. For this purpose, the experiments were done at six levels of varied temperatures: 10°C, 20°C, 30°C, 40°C, 50°C and 60°C. The values of effective diffusion coefficients obtained in this work for the variously treated ginger rhizomes closely agreed with the average effective diffusion coefficients of other notable authors who determined the drying kinetics and convective heat transfer coefficients of ginger slices.展开更多
Benefits achieved by the biodegradable magnesium(Mg) and zinc(Zn) implants could be suppressed due to the invasion of infectious microbial, common bacteria, and fungi. Postoperative medications and the antibacterial p...Benefits achieved by the biodegradable magnesium(Mg) and zinc(Zn) implants could be suppressed due to the invasion of infectious microbial, common bacteria, and fungi. Postoperative medications and the antibacterial properties of pure Mg and Zn are insufficient against biofilm and antibiotic-resistant bacteria, bringing osteomyelitis, necrosis, and even death. This study evaluates the antibacterial performance of biodegradable Mg and Zn alloys of different reinforcements, including silver(Ag), copper(Cu), lithium(Li), and gallium(Ga). Copper ions(Cu^(2+)) can eradicate biofilms and antibiotic-resistant bacteria by extracting electrons from the cellular structure. Silver ion(Ag^(+)) kills bacteria by creating bonds with the thiol group. Gallium ion(Ga^(3+)) inhibits ferric ion(Fe^(3+)) absorption, leading to nutrient deficiency and bacterial death. Nanoparticles and reactive oxygen species(ROS) can penetrate bacteria cell walls directly, develop bonds with receptors, and damage nucleotides. Antibacterial action depends on the alkali nature of metal ions and their degradation rate, which often causes cytotoxicity in living cells. Therefore, this review emphasizes the insight into degradation rate, antibacterial mechanism, and their consequent cytotoxicity and observes the correlation between antibacterial performance and oxidation number of metal ions.展开更多
Waste Glass(WGs)and Coir Fiber(CF)are not widely utilized,even though their silica and cellulose content can be used to create construction materials.This study aimed to optimize mortar compressive strength using Resp...Waste Glass(WGs)and Coir Fiber(CF)are not widely utilized,even though their silica and cellulose content can be used to create construction materials.This study aimed to optimize mortar compressive strength using Response Surface Methodology(RSM).The Central Composite Design(CCD)was applied to determine the optimization of WGs and CF addition to the mortar compressive strength.Compressive strength and microstructure testing with Scanning Electron Microscope(SEM),Fourier-transform Infrared Spectroscopy(FT-IR),and X-Ray Diffraction(XRD)were conducted to specify the mechanical ability and bonding between the matrix,CF,and WGs.The results showed that the chemical treatment of CF produced 49.15%cellulose,with an average particle size of 1521μm.The regression of a second-order polynomial model yielded an optimum composition consisting of 12.776%WGs and 2.344%CF with a predicted compressive strength of 19.1023 MPa.C-S-H gels were identified in the mortars due to the dissolving of SiO_(2) in WGs and cement.The silica from WGs increased the C-S-H phase.CF plays a role in preventing,bridging,and branching micro-cracks before reaching maximum stress.WGs aggregates and chemically treated CF are suitable to be composited in mortar to increase compressive strength.展开更多
In this study,the best manufacturing process will be selected to build an automotive crash box using green oil palm natural fibre-reinforced polyurethane composite materials.This paper introduces an approach consist o...In this study,the best manufacturing process will be selected to build an automotive crash box using green oil palm natural fibre-reinforced polyurethane composite materials.This paper introduces an approach consist of technical aspects(T),the economic point of view(E)and availability(A),and it’s also called as TEA requirement.This approach was developed with the goal of assisting the design engineer in the selection of the best manufacturing process during the design phase at the criteria selection stage.In this study,the TEA requirement will integrate with the analytical hierarchy process(AHP)to assist decision makers or manufacturing engineers in determining the most appropriate manufacturing process to be employed in the manufacture of a composite automotive crash box(ACB)at the early stage of the product development process.It is obvious that a major challenge in the manufacturing selection process is lack of information regarding manufacturing of ACB using natural fibre composite(NFC).There have been no previous studies that examined ranking manufacturability processes in terms of their suitability.Therefore,the TEA-AHP hybrid method was introduced to provide unprejudiced criteria-ranking selection prior to evaluation of pairwise comparisons.At the end of this study,the pulforming process was selected as the best manufacturing process for fabrication of the ACB structural component.展开更多
To reduce peak electricity demand and hence reduce capacity costs due to added investment of generating additional power to meet short intervals of peak demand, can enhance energy efficiency. Where it is possible to a...To reduce peak electricity demand and hence reduce capacity costs due to added investment of generating additional power to meet short intervals of peak demand, can enhance energy efficiency. Where it is possible to adjust timing and the quantity of electricity consumption and at the same time achieve the same useful effect, the value of the energy service itself remains unchanged. Peak demand management is viewed as the balance between demand and generation of energy hence an important requirement for stabilized operation of power system. Therefore, the purpose of this study was to establish the correlation between peak electricity demand management strategies and energy efficiency among large steel manufacturing firms in Nairobi, Kenya. The strategies investigated were demand scheduling, Peak shrinking and Peak shaving. Demand scheduling involves shifting predetermined loads to low peak periods thereby flattening the demand curve. Peak shrinking on the other hand involves installation of energy efficient equipment thereby shifting the overall demand curve downwards. Peak shaving is the deployment of secondary generation on site to temporarily power some loads during peak hours thereby reducing demand during the peak periods of the plant. The specific objectives were to test the relationship between demand scheduling and energy efficiency among large steel manufacturing firms in Nairobi Region;to test the correlation between peak shrinking and energy efficiency among large steel manufacturing firms in Nairobi Region;and to test the association between peak shaving and energy efficiency among large steel manufacturing firms in Nairobi Region. The study adopted a descriptive research design to determine the relationship between each independent variable namely demand scheduling, peak shrinking, peak shaving and the dependent variable, the energy efficiency. The target population was large steel manufacturing firms in Nairobi Region, Kenya. The study used both primary and secondary data. The primary data was from structured questionnaires while secondary data was from historical electricity consumption data for the firms under study. The results revealed that both peak shrinking and peak shaving were statistically significant in influencing energy efficiency among the steel manufacturing firms in Nairobi Region, each with Pearson correlation coefficient of 0.903, thus a strong linear relationship between the investigated strategy and the dependent variable, energy efficiency. The obtained results are significant at probability value of 0.005 (p 0.05). The conclusion is that peak shrinking and peak shaving have an impact on energy efficiency in the population under study, and if properly implemented, may lead to efficient utilization of the available energy. The study further recommended that peak demand management practices need to be implemented efficiently as a way of improving the overall plant load factor and energy efficiency.展开更多
Small-scaled wind turbine is converted to mechanical power of windmill to electric power by generator. However almost all studies seems to have overlooked converting relation of mechanical & electric power. It the...Small-scaled wind turbine is converted to mechanical power of windmill to electric power by generator. However almost all studies seems to have overlooked converting relation of mechanical & electric power. It the reason for was very difficult establishing wind turbine system. In this paper, it is define equation of converting relation of mechanical & electric power. And it is verified by experimental methods. Defined equation will be used in developing electric devices such as inverter and controller in wind turbines. In addition this method can be used in the fields that utilize the rotational power into electrical power through generator.展开更多
Factors for determining the spindle size are the shaft diameter,positions of bearing and motor,and entire length of the spindle.Then,it is important to find the assembling of the optimal design variables,which satisfy...Factors for determining the spindle size are the shaft diameter,positions of bearing and motor,and entire length of the spindle.Then,it is important to find the assembling of the optimal design variables,which satisfy the stiffness and rotational speed required to the spindle.A general full factorial design method was used to verify some factors that affect the natural frequency of a spindle.It is verified that the shorter shaft length and bearing span length represent the higher natural frequency,and there are some effects according to the change in the levels of factors.The detailed spindle dimension is determined by applying an EVD method,which can define the optimal bearing position through considering the limiting condition.Based on the estimated regression model,the optimal spindle size and bearing distance that can improve the primary natural frequency are obtained,and the influence of design factors on the natural frequency is also analyzed.展开更多
Unsteady wake from upstream components of landing gear impinging on downstream components could be a strong noise source.The use of a plane jet is proposed to reduce this flow-induced noise.Tandem rods with different ...Unsteady wake from upstream components of landing gear impinging on downstream components could be a strong noise source.The use of a plane jet is proposed to reduce this flow-induced noise.Tandem rods with different gap widths were utilized as the test body.Both acoustic and aerodynamic tests were conducted in order to validate this technique.Acoustic test results proved that overall noise emission from tandem rods could be lowered and tonal noise could be removed with use of the plane jet.However,when the plane jet was turned on,in some frequency range it could be the subsequent main contributor instead of tandem rods to total noise emission whilst in some frequency range rods could still be the main contributor.Moreover,aerodynamic tests fundamentally studied explanations for the noise reduction.Specifically,not only impinging speed to rods but speed and turbulence level to the top edge of the rear rod could be diminished by the upstream plane jet.Consequently,the vortex shedding induced by the rear rod was reduced,which was confirmed by the speed,Reynolds stress as well as the velocity fluctuation spectral measured in its wake.This study confirmed the potential use of a plane jet towards landing gear noise reduction.展开更多
The undercooling and solidification of 150 μm and 185 μm droplets of Sn 5%Pb alloy prepared by the uniform droplet spray (UDS) process have been investigated. The enthalpy of the droplet has been measured by non adi...The undercooling and solidification of 150 μm and 185 μm droplets of Sn 5%Pb alloy prepared by the uniform droplet spray (UDS) process have been investigated. The enthalpy of the droplet has been measured by non adiabatic calorimetric method as a function of the flight distance. A droplet solidification simulation model has been used to compare with the experimental data. The results show that the enthalpy released by the droplets in the calorimeter is 11.88 J/g and 22.29 J/g less than the simulated values up to a certain flight distance at 0.485 m and 0.460 m for 150 μm and 185 μm droplets respectively, but agrees with the expected values at larger distance. The nucleation of the droplets takes place at the distance where the experimental and simulated enthalpy values agree. The droplets quenched before nucleation solidify into metastable supersaturated solid solution and have large undercooling. The formation of the metastable structure in the droplets has been verified metallographically and by calculations based on a thermodynamic model.展开更多
With the innovation of microelectronics technology, the heat dissipation problem inside the device will face a severe test. In this work, cellulose aerogel(CA) with highly enhanced thermal conductivity(TC) in vertical...With the innovation of microelectronics technology, the heat dissipation problem inside the device will face a severe test. In this work, cellulose aerogel(CA) with highly enhanced thermal conductivity(TC) in vertical planes was successfully obtained by constructing a vertically aligned silicon carbide nanowires(SiC NWs)/boron nitride(BN) network via the ice template-assisted strategy. The unique network structure of SiC NWs connected to BN ensures that the TC of the composite in the vertical direction reaches 2.21 W m^(-1) K^(-1) at a low hybrid filler loading of 16.69 wt%, which was increased by 890% compared to pure epoxy(EP). In addition, relying on unique porous network structure of CA, EP-based composite also showed higher TC than other comparative samples in the horizontal direction. Meanwhile, the composite exhibits good electrically insulating with a volume electrical resistivity about 2.35 × 10^(11) Ω cm and displays excellent electromagnetic wave absorption performance with a minimum reflection loss of-21.5 dB and a wide effective absorption bandwidth(<-10 dB) from 8.8 to 11.6 GHz. Therefore, this work provides a new strategy for manufacturing polymer-based composites with excellent multifunctional performances in microelectronic packaging applications.展开更多
The paper presents the investigation of the effect of alkaline treatment of sodium hydroxide(NaOH) on physical and dynamic mechanical analysis(DMA) viscoelastic properties of kenaf fibre filled natural rubber(NR)/ther...The paper presents the investigation of the effect of alkaline treatment of sodium hydroxide(NaOH) on physical and dynamic mechanical analysis(DMA) viscoelastic properties of kenaf fibre filled natural rubber(NR)/thermoplastic polyurethane(TPU) composites.The treated kenaf fiber,NR and TPU were weighed and proportioned according to the required compositions and were blended using hot mixed Brabender machine.The polymer composites were then fabricated using the hot press to form a sample board.The sample was cut and prepared and water absorption,density,thickness swelling and DMA tests were performed.As far as physical properties are concerned,composites with the highest NR amount of shows the best results,which indicates good fiber bonding adhesion.The polymer composites with the highest amount of TPU shows the highest damping properties at high temperature.展开更多
Laser assisted machining (LAM) has difficulties in estimating temperature after applying a LAM process due to its very small heat input area, large energy and movement. In particular, in the case of laser assisted tur...Laser assisted machining (LAM) has difficulties in estimating temperature after applying a LAM process due to its very small heat input area, large energy and movement. In particular, in the case of laser assisted turning (LAT) process, it is more difficult to estimate the temperature after preheating because it has a shape of ellipse when a laser heat source is rotated. A prediction method and thermal analysis method for heat source shapes were proposed as a square shaped member was preheated. The temperature distribution was calculated according to the rotation of the member. Compared with the results of the former study, the maximum temperature of the calculation results, 1 407.1 °C, is 8.5 °C higher than that of the square member, which is 1 398.6 °C. In a LAT process for a square member, the maximum temperature is 1 850.8 °C. It is recognized that a laser power control process is required because square members show a maximum temperature that exceeds a melting temperature at around a vertex of the member according to the rotation.展开更多
The parametric excited vibration of a pipe under thermal loading may occur because the fluid is often transported heatedly. The effects of thermal loading on the pipe stability and local bifurcations have rarely been ...The parametric excited vibration of a pipe under thermal loading may occur because the fluid is often transported heatedly. The effects of thermal loading on the pipe stability and local bifurcations have rarely been studied. The stability and the local bifurcations of the lateral parametric resonance of the pipe induced by the pulsating fluid velocity and the thermal loading are studied. A mathematical model for a simply supported pipe is developed according to the Hamilton principle. Two partial differential equations describing the lateral and longitudinal vibration are obtained. The singularity theory is utilized to analyze the stability and the bifurcation of the system solutions. The transition sets and the bifurcation diagrams are obtained both in the unfolding parameter space and the physical parameter space, which can reveal the relationship between the thermal field parameter and the dynamic behaviors of the pipe. The frequency response and the relationship between the critical thermal rate and the pulsating fluid velocity are obtained. The numerical results demonstrate the accuracy of the single-mode expansion of the solution and the stability and local bifurcation analyses. It also confirms the existence of the chaos. The presented work can provide valuable information for the design of the pipeline and the controllers to prevent the structural instability.展开更多
In this study, annealed pure copper was extruded using equal channel angular extrusion(ECAE) for a maximum of eight passes.The fatigue resistance of extruded specimens was evaluated for different passes and applied st...In this study, annealed pure copper was extruded using equal channel angular extrusion(ECAE) for a maximum of eight passes.The fatigue resistance of extruded specimens was evaluated for different passes and applied stresses using fatigue tests, fractography, and metallography. The mechanical properties of the extruded material were obtained at a tensile test velocity of 0.5 mm/min. It was found that the maximum increase in strength occurred after the 2nd pass. The total increase in ultimate strength after eight passes was 94%. The results of fatigue tests indicated that a significant improvement in fatigue life occurred after the 2nd pass. In subsequent passes, the fatigue life continued to improve but at a considerably lower rate. The improved fatigue life was dependent on the number of passes and applied stresses.For low stresses(or high-cycle fatigue), a maximum increase in fatigue resistance of approximately 500% was observed for the extruded material after eight passes, whereas a maximum fatigue resistance of 5000% was obtained for high-applied stresses(or low-cycle fatigue).Optical microscopic examinations revealed grain refinements in the range of 32 to 4 μm. A maximum increase in impact energy absorption of 100% was achieved after eight passes. Consistent results were obtained from fractography and metallography examinations of the extruded material during fatigue tests.展开更多
Complex thin-walled titanium alloy components play a key role in the aircraft,aerospace and marine industries,offering the advantages of reduced weight and increased thermal resistance.The geometrical complexity,dimen...Complex thin-walled titanium alloy components play a key role in the aircraft,aerospace and marine industries,offering the advantages of reduced weight and increased thermal resistance.The geometrical complexity,dimensional accuracy and in-service properties are essential to fulfill the high-performance standards required in new transportation systems,which brings new challenges to titanium alloy forming technologies.Traditional forming processes,such as superplastic forming or hot pressing,cannot meet all demands of modern applications due to their limited properties,low productivity and high cost.This has encouraged industry and research groups to develop novel high-efficiency forming processes.Hot gas pressure forming and hot stamping-quenching technologies have been developed for the manufacture of tubular and panel components,and are believed to be the cut-edge processes guaranteeing dimensional accuracy,microstructure and mechanical properties.This article intends to provide a critical review of high-efficiency titanium alloy forming processes,concentrating on latest investigations of controlling dimensional accuracy,microstructure and properties.The advantages and limitations of individual forming process are comprehensively analyzed,through which,future research trends of high-efficiency forming are identified including trends in process integration,processing window design,full cycle and multi-objective optimization.This review aims to provide a guide for researchers and process designers on the manufacture of thin-walled titanium alloy components whilst achieving high dimensional accuracy and satisfying performance properties with high efficiency and low cost.展开更多
The novel coronavirus responsible for COVID-19 has spread to several countries within a considerably short period.The virus gets deposited in the human nasal cavity and moves to the lungs that might be fatal.As per sa...The novel coronavirus responsible for COVID-19 has spread to several countries within a considerably short period.The virus gets deposited in the human nasal cavity and moves to the lungs that might be fatal.As per safety guidelines by theWorld Health Organization(WHO),social distancing has emerged as one of the major factors to avoid the spread of infection.However,different guidelines are being followed across the countries with regards to what should be the safe distance.Thus,the current work is an attempt to understand the virus deposition pattern in the realistic human nasal cavity and also to find the impact of distance that could be termed as a safety measure.This study is performed usingComputationalFluid Dynamics as a solution tool to investigate the impact of COVID-19 deposition(i)On a realistic 3D human upper airway model and(ii)2D social distancing protocol for a distance of 0.6,1.2,1.8,and 2.4 m.The results revealed that the regional deposition flux within the nasal cavity was predominantly observed in the external nasal cavity and nasopharyngeal section.Frequent flushing of these regions with saltwater substitutes can limit contamination in healthy individuals.The safe distancing limit estimated with 1 m/s airflow was about 1.8 m.The extensive deposition was observed for distances less than 1.8 m in this study,emphasizing the fact that social distancing advisories are not useful and do not take into account the external dynamics associated with airflow.展开更多
Cylindrical Cam Mechanism which is one of the best eq uipments to accomplish an accurate motion transmission is widely used in the fie lds of industries, such as machine tool exchangers, textile machinery and automa t...Cylindrical Cam Mechanism which is one of the best eq uipments to accomplish an accurate motion transmission is widely used in the fie lds of industries, such as machine tool exchangers, textile machinery and automa tic transfer equipments. This paper proposes a new approach for the shape design and manufacturing of the cylindrical cam. The design approach uses the relative velocity concept and the manufacturing approach uses the inverse kinematics concept. For the shape desig n, the contact points between the cam and the follower roller are calculated bas ed on relative velocity of which the direction is on the common tangential line, and then the whole shape of cam is determined from transformation of the coordi nate system. For the manufacturing procedures, the location and the orientation of cutter path can be allocated corresponding to the designed shape data. The in tegral NC code for multi-axis CNC machining center is created using the inverse kinematics concept from the data of the location and the orientation of cutter path. As the advantages of the proposed approach, the machine tool is designed t o having an alternative size in fabricating the general cam, while the tool must be fitted to diameter size of the follower in the conventional approach. Finally, CAD/CAM program, "Cylindrical DAM", is developed on C++ lan guage. This program can perform shape design, manufacturing and kinematics simul ation, which can make integral NC code for multi-axis CNC machining center. The proposed method can be applied easily on fields of industries.展开更多
This article delivers a robust overview of potential electrode materials for use in symmetrical solid oxide fuel cells(S-SOFCs),a relatively new SOFC technology.To this end,this article provides a comprehensive review...This article delivers a robust overview of potential electrode materials for use in symmetrical solid oxide fuel cells(S-SOFCs),a relatively new SOFC technology.To this end,this article provides a comprehensive review of recent advances and progress in electrode materials for S-SOFC,discussing both the selection of materials and the challenges that come with making that choice.This article discussed the relevant factors involved in developing electrodes with nano/microstructure.Nanocomposites,e.g.,non-cobalt and lithiated materials,are only a few of the electrode types now being researched.Furthermore,the phase structure and microstructure of the produced materials are heavily influenced by the synthesis procedure.Insights into the possibilities and difficulties of the material are discussed.To achieve the desired microstructural features,this article focuses on a synthesis technique that is either the most recent or a better iteration of an existing process.The portion of this analysis that addresses the risks associated with manufacturing and the challenges posed by materials when fabricating S-SOFCs is the most critical.This article also provides important and useful recommendations for the strategic design of electrode materials researchers.展开更多
Green cutting has become focus of attention in ecological and environmental protection. Steam is cheap, pollu-tion-free and eco-friendly, and then is a good and economical coolant and lubricant. Steam generator and st...Green cutting has become focus of attention in ecological and environmental protection. Steam is cheap, pollu-tion-free and eco-friendly, and then is a good and economical coolant and lubricant. Steam generator and steam feeding system were developed to generate and feed steam. Comparative experiments were carried out in cutting AA6061-15 vol.% SiC (25 μm particle size), with cubic boron nitride (CBN) insert KB-90 grade under the conditions of compressed air, oil water emulsion, steam as coolant and lubricant, and dry cutting, respectively. The experimental results show that, with steam as coolant and lu-bricant, gradual reduction in the cutting force, friction coefficient, surface roughness and cutting temperature values were observed. Further, there was reduction in built up edge formation. It is proved that use of water steam as coolant and lubricant is environ-mentally friendly.展开更多
文摘This study is an extension of the previous work done with ARS-680 Environmental Chamber. Drying is a complex operation that demands much energy and time. Drying is essentially important for preservation of ginger rhizome. Drying of ginger was modeled, and then the effective diffusion coefficient and activation energy were determined. For this purpose, the experiments were done at six levels of varied temperatures: 10°C, 20°C, 30°C, 40°C, 50°C and 60°C. The values of effective diffusion coefficients obtained in this work for the variously treated ginger rhizomes closely agreed with the average effective diffusion coefficients of other notable authors who determined the drying kinetics and convective heat transfer coefficients of ginger slices.
基金support by Universiti Teknologi PETRONAS (UTP),Malaysia,under Grant No.015LC0-336。
文摘Benefits achieved by the biodegradable magnesium(Mg) and zinc(Zn) implants could be suppressed due to the invasion of infectious microbial, common bacteria, and fungi. Postoperative medications and the antibacterial properties of pure Mg and Zn are insufficient against biofilm and antibiotic-resistant bacteria, bringing osteomyelitis, necrosis, and even death. This study evaluates the antibacterial performance of biodegradable Mg and Zn alloys of different reinforcements, including silver(Ag), copper(Cu), lithium(Li), and gallium(Ga). Copper ions(Cu^(2+)) can eradicate biofilms and antibiotic-resistant bacteria by extracting electrons from the cellular structure. Silver ion(Ag^(+)) kills bacteria by creating bonds with the thiol group. Gallium ion(Ga^(3+)) inhibits ferric ion(Fe^(3+)) absorption, leading to nutrient deficiency and bacterial death. Nanoparticles and reactive oxygen species(ROS) can penetrate bacteria cell walls directly, develop bonds with receptors, and damage nucleotides. Antibacterial action depends on the alkali nature of metal ions and their degradation rate, which often causes cytotoxicity in living cells. Therefore, this review emphasizes the insight into degradation rate, antibacterial mechanism, and their consequent cytotoxicity and observes the correlation between antibacterial performance and oxidation number of metal ions.
基金funded by the Ministry of Education,Culture,Research,and the Technology,Indonesia for Matching Fund (Kedaireka)Scheme in 2022 with Contract No.155/E1/KS.06.02/2022.
文摘Waste Glass(WGs)and Coir Fiber(CF)are not widely utilized,even though their silica and cellulose content can be used to create construction materials.This study aimed to optimize mortar compressive strength using Response Surface Methodology(RSM).The Central Composite Design(CCD)was applied to determine the optimization of WGs and CF addition to the mortar compressive strength.Compressive strength and microstructure testing with Scanning Electron Microscope(SEM),Fourier-transform Infrared Spectroscopy(FT-IR),and X-Ray Diffraction(XRD)were conducted to specify the mechanical ability and bonding between the matrix,CF,and WGs.The results showed that the chemical treatment of CF produced 49.15%cellulose,with an average particle size of 1521μm.The regression of a second-order polynomial model yielded an optimum composition consisting of 12.776%WGs and 2.344%CF with a predicted compressive strength of 19.1023 MPa.C-S-H gels were identified in the mortars due to the dissolving of SiO_(2) in WGs and cement.The silica from WGs increased the C-S-H phase.CF plays a role in preventing,bridging,and branching micro-cracks before reaching maximum stress.WGs aggregates and chemically treated CF are suitable to be composited in mortar to increase compressive strength.
文摘In this study,the best manufacturing process will be selected to build an automotive crash box using green oil palm natural fibre-reinforced polyurethane composite materials.This paper introduces an approach consist of technical aspects(T),the economic point of view(E)and availability(A),and it’s also called as TEA requirement.This approach was developed with the goal of assisting the design engineer in the selection of the best manufacturing process during the design phase at the criteria selection stage.In this study,the TEA requirement will integrate with the analytical hierarchy process(AHP)to assist decision makers or manufacturing engineers in determining the most appropriate manufacturing process to be employed in the manufacture of a composite automotive crash box(ACB)at the early stage of the product development process.It is obvious that a major challenge in the manufacturing selection process is lack of information regarding manufacturing of ACB using natural fibre composite(NFC).There have been no previous studies that examined ranking manufacturability processes in terms of their suitability.Therefore,the TEA-AHP hybrid method was introduced to provide unprejudiced criteria-ranking selection prior to evaluation of pairwise comparisons.At the end of this study,the pulforming process was selected as the best manufacturing process for fabrication of the ACB structural component.
文摘To reduce peak electricity demand and hence reduce capacity costs due to added investment of generating additional power to meet short intervals of peak demand, can enhance energy efficiency. Where it is possible to adjust timing and the quantity of electricity consumption and at the same time achieve the same useful effect, the value of the energy service itself remains unchanged. Peak demand management is viewed as the balance between demand and generation of energy hence an important requirement for stabilized operation of power system. Therefore, the purpose of this study was to establish the correlation between peak electricity demand management strategies and energy efficiency among large steel manufacturing firms in Nairobi, Kenya. The strategies investigated were demand scheduling, Peak shrinking and Peak shaving. Demand scheduling involves shifting predetermined loads to low peak periods thereby flattening the demand curve. Peak shrinking on the other hand involves installation of energy efficient equipment thereby shifting the overall demand curve downwards. Peak shaving is the deployment of secondary generation on site to temporarily power some loads during peak hours thereby reducing demand during the peak periods of the plant. The specific objectives were to test the relationship between demand scheduling and energy efficiency among large steel manufacturing firms in Nairobi Region;to test the correlation between peak shrinking and energy efficiency among large steel manufacturing firms in Nairobi Region;and to test the association between peak shaving and energy efficiency among large steel manufacturing firms in Nairobi Region. The study adopted a descriptive research design to determine the relationship between each independent variable namely demand scheduling, peak shrinking, peak shaving and the dependent variable, the energy efficiency. The target population was large steel manufacturing firms in Nairobi Region, Kenya. The study used both primary and secondary data. The primary data was from structured questionnaires while secondary data was from historical electricity consumption data for the firms under study. The results revealed that both peak shrinking and peak shaving were statistically significant in influencing energy efficiency among the steel manufacturing firms in Nairobi Region, each with Pearson correlation coefficient of 0.903, thus a strong linear relationship between the investigated strategy and the dependent variable, energy efficiency. The obtained results are significant at probability value of 0.005 (p 0.05). The conclusion is that peak shrinking and peak shaving have an impact on energy efficiency in the population under study, and if properly implemented, may lead to efficient utilization of the available energy. The study further recommended that peak demand management practices need to be implemented efficiently as a way of improving the overall plant load factor and energy efficiency.
文摘Small-scaled wind turbine is converted to mechanical power of windmill to electric power by generator. However almost all studies seems to have overlooked converting relation of mechanical & electric power. It the reason for was very difficult establishing wind turbine system. In this paper, it is define equation of converting relation of mechanical & electric power. And it is verified by experimental methods. Defined equation will be used in developing electric devices such as inverter and controller in wind turbines. In addition this method can be used in the fields that utilize the rotational power into electrical power through generator.
基金Project(RTI04-01-03) supported by the Regional Technology Innovation Program of the Ministry of Knowledge Economy (MKE) of Korea
文摘Factors for determining the spindle size are the shaft diameter,positions of bearing and motor,and entire length of the spindle.Then,it is important to find the assembling of the optimal design variables,which satisfy the stiffness and rotational speed required to the spindle.A general full factorial design method was used to verify some factors that affect the natural frequency of a spindle.It is verified that the shorter shaft length and bearing span length represent the higher natural frequency,and there are some effects according to the change in the levels of factors.The detailed spindle dimension is determined by applying an EVD method,which can define the optimal bearing position through considering the limiting condition.Based on the estimated regression model,the optimal spindle size and bearing distance that can improve the primary natural frequency are obtained,and the influence of design factors on the natural frequency is also analyzed.
基金Project partially supported by the European Union FP7 Clean Sky Joint Technology Initiative“ALLEGRA”(Grant No.308225)
文摘Unsteady wake from upstream components of landing gear impinging on downstream components could be a strong noise source.The use of a plane jet is proposed to reduce this flow-induced noise.Tandem rods with different gap widths were utilized as the test body.Both acoustic and aerodynamic tests were conducted in order to validate this technique.Acoustic test results proved that overall noise emission from tandem rods could be lowered and tonal noise could be removed with use of the plane jet.However,when the plane jet was turned on,in some frequency range it could be the subsequent main contributor instead of tandem rods to total noise emission whilst in some frequency range rods could still be the main contributor.Moreover,aerodynamic tests fundamentally studied explanations for the noise reduction.Specifically,not only impinging speed to rods but speed and turbulence level to the top edge of the rear rod could be diminished by the upstream plane jet.Consequently,the vortex shedding induced by the rear rod was reduced,which was confirmed by the speed,Reynolds stress as well as the velocity fluctuation spectral measured in its wake.This study confirmed the potential use of a plane jet towards landing gear noise reduction.
文摘The undercooling and solidification of 150 μm and 185 μm droplets of Sn 5%Pb alloy prepared by the uniform droplet spray (UDS) process have been investigated. The enthalpy of the droplet has been measured by non adiabatic calorimetric method as a function of the flight distance. A droplet solidification simulation model has been used to compare with the experimental data. The results show that the enthalpy released by the droplets in the calorimeter is 11.88 J/g and 22.29 J/g less than the simulated values up to a certain flight distance at 0.485 m and 0.460 m for 150 μm and 185 μm droplets respectively, but agrees with the expected values at larger distance. The nucleation of the droplets takes place at the distance where the experimental and simulated enthalpy values agree. The droplets quenched before nucleation solidify into metastable supersaturated solid solution and have large undercooling. The formation of the metastable structure in the droplets has been verified metallographically and by calculations based on a thermodynamic model.
基金financial support from National Natural Science Foundation of China(21704096,51703217)the China Postdoctoral Science Foundation(Grant No.2019M662526)financial support from Taif University Researchers Supporting Project Number(TURSP-2020/135),Taif University,Taif,Saudi Arabia。
文摘With the innovation of microelectronics technology, the heat dissipation problem inside the device will face a severe test. In this work, cellulose aerogel(CA) with highly enhanced thermal conductivity(TC) in vertical planes was successfully obtained by constructing a vertically aligned silicon carbide nanowires(SiC NWs)/boron nitride(BN) network via the ice template-assisted strategy. The unique network structure of SiC NWs connected to BN ensures that the TC of the composite in the vertical direction reaches 2.21 W m^(-1) K^(-1) at a low hybrid filler loading of 16.69 wt%, which was increased by 890% compared to pure epoxy(EP). In addition, relying on unique porous network structure of CA, EP-based composite also showed higher TC than other comparative samples in the horizontal direction. Meanwhile, the composite exhibits good electrically insulating with a volume electrical resistivity about 2.35 × 10^(11) Ω cm and displays excellent electromagnetic wave absorption performance with a minimum reflection loss of-21.5 dB and a wide effective absorption bandwidth(<-10 dB) from 8.8 to 11.6 GHz. Therefore, this work provides a new strategy for manufacturing polymer-based composites with excellent multifunctional performances in microelectronic packaging applications.
基金Universiti Kuala Lumpur(UniKL)the Ministry of Education Malaysia for providing the scholarship award+1 种基金financially support through UniKL Grant Scheme(STRG 15144)to the principal author in this projectHiCOE grant(6369107)from the Ministry of Education,Malaysia。
文摘The paper presents the investigation of the effect of alkaline treatment of sodium hydroxide(NaOH) on physical and dynamic mechanical analysis(DMA) viscoelastic properties of kenaf fibre filled natural rubber(NR)/thermoplastic polyurethane(TPU) composites.The treated kenaf fiber,NR and TPU were weighed and proportioned according to the required compositions and were blended using hot mixed Brabender machine.The polymer composites were then fabricated using the hot press to form a sample board.The sample was cut and prepared and water absorption,density,thickness swelling and DMA tests were performed.As far as physical properties are concerned,composites with the highest NR amount of shows the best results,which indicates good fiber bonding adhesion.The polymer composites with the highest amount of TPU shows the highest damping properties at high temperature.
基金Project(70004782)supported by the Regional Strategic Technology Development Program of the Ministry of Knowledge Economy(MKE),KoreaProject(2011-0017407)supported by National Research Foundation(NRF)of KoreaWork financially supported by the Second Stage of Brain Korea 21 Projects
文摘Laser assisted machining (LAM) has difficulties in estimating temperature after applying a LAM process due to its very small heat input area, large energy and movement. In particular, in the case of laser assisted turning (LAT) process, it is more difficult to estimate the temperature after preheating because it has a shape of ellipse when a laser heat source is rotated. A prediction method and thermal analysis method for heat source shapes were proposed as a square shaped member was preheated. The temperature distribution was calculated according to the rotation of the member. Compared with the results of the former study, the maximum temperature of the calculation results, 1 407.1 °C, is 8.5 °C higher than that of the square member, which is 1 398.6 °C. In a LAT process for a square member, the maximum temperature is 1 850.8 °C. It is recognized that a laser power control process is required because square members show a maximum temperature that exceeds a melting temperature at around a vertex of the member according to the rotation.
基金Project supported by the National Natural Science Foundation of Shandong Province(No.ZR2013AL017)the National Natural Science Foundation of China(No.11272357)the Fundamental Research Funds for the Central Universities of China(No.11CX04049A)
文摘The parametric excited vibration of a pipe under thermal loading may occur because the fluid is often transported heatedly. The effects of thermal loading on the pipe stability and local bifurcations have rarely been studied. The stability and the local bifurcations of the lateral parametric resonance of the pipe induced by the pulsating fluid velocity and the thermal loading are studied. A mathematical model for a simply supported pipe is developed according to the Hamilton principle. Two partial differential equations describing the lateral and longitudinal vibration are obtained. The singularity theory is utilized to analyze the stability and the bifurcation of the system solutions. The transition sets and the bifurcation diagrams are obtained both in the unfolding parameter space and the physical parameter space, which can reveal the relationship between the thermal field parameter and the dynamic behaviors of the pipe. The frequency response and the relationship between the critical thermal rate and the pulsating fluid velocity are obtained. The numerical results demonstrate the accuracy of the single-mode expansion of the solution and the stability and local bifurcation analyses. It also confirms the existence of the chaos. The presented work can provide valuable information for the design of the pipeline and the controllers to prevent the structural instability.
基金the Research Council and the Vice Chancellor of Research Affairs of Islamic Azad Universitythe University Putra Malaysia for its support
文摘In this study, annealed pure copper was extruded using equal channel angular extrusion(ECAE) for a maximum of eight passes.The fatigue resistance of extruded specimens was evaluated for different passes and applied stresses using fatigue tests, fractography, and metallography. The mechanical properties of the extruded material were obtained at a tensile test velocity of 0.5 mm/min. It was found that the maximum increase in strength occurred after the 2nd pass. The total increase in ultimate strength after eight passes was 94%. The results of fatigue tests indicated that a significant improvement in fatigue life occurred after the 2nd pass. In subsequent passes, the fatigue life continued to improve but at a considerably lower rate. The improved fatigue life was dependent on the number of passes and applied stresses.For low stresses(or high-cycle fatigue), a maximum increase in fatigue resistance of approximately 500% was observed for the extruded material after eight passes, whereas a maximum fatigue resistance of 5000% was obtained for high-applied stresses(or low-cycle fatigue).Optical microscopic examinations revealed grain refinements in the range of 32 to 4 μm. A maximum increase in impact energy absorption of 100% was achieved after eight passes. Consistent results were obtained from fractography and metallography examinations of the extruded material during fatigue tests.
基金This work was financially supported by the Program of National Natural Science Foundation of China(Nos.U1937204 and 51905124)China Postdoctoral Science Foundation(2019M661278).
文摘Complex thin-walled titanium alloy components play a key role in the aircraft,aerospace and marine industries,offering the advantages of reduced weight and increased thermal resistance.The geometrical complexity,dimensional accuracy and in-service properties are essential to fulfill the high-performance standards required in new transportation systems,which brings new challenges to titanium alloy forming technologies.Traditional forming processes,such as superplastic forming or hot pressing,cannot meet all demands of modern applications due to their limited properties,low productivity and high cost.This has encouraged industry and research groups to develop novel high-efficiency forming processes.Hot gas pressure forming and hot stamping-quenching technologies have been developed for the manufacture of tubular and panel components,and are believed to be the cut-edge processes guaranteeing dimensional accuracy,microstructure and mechanical properties.This article intends to provide a critical review of high-efficiency titanium alloy forming processes,concentrating on latest investigations of controlling dimensional accuracy,microstructure and properties.The advantages and limitations of individual forming process are comprehensively analyzed,through which,future research trends of high-efficiency forming are identified including trends in process integration,processing window design,full cycle and multi-objective optimization.This review aims to provide a guide for researchers and process designers on the manufacture of thin-walled titanium alloy components whilst achieving high dimensional accuracy and satisfying performance properties with high efficiency and low cost.
基金The authors are thankful to the Institute of Research and Consulting Studies at King Khalid University for supporting this research through Grant No.#34-67-S-2020.
文摘The novel coronavirus responsible for COVID-19 has spread to several countries within a considerably short period.The virus gets deposited in the human nasal cavity and moves to the lungs that might be fatal.As per safety guidelines by theWorld Health Organization(WHO),social distancing has emerged as one of the major factors to avoid the spread of infection.However,different guidelines are being followed across the countries with regards to what should be the safe distance.Thus,the current work is an attempt to understand the virus deposition pattern in the realistic human nasal cavity and also to find the impact of distance that could be termed as a safety measure.This study is performed usingComputationalFluid Dynamics as a solution tool to investigate the impact of COVID-19 deposition(i)On a realistic 3D human upper airway model and(ii)2D social distancing protocol for a distance of 0.6,1.2,1.8,and 2.4 m.The results revealed that the regional deposition flux within the nasal cavity was predominantly observed in the external nasal cavity and nasopharyngeal section.Frequent flushing of these regions with saltwater substitutes can limit contamination in healthy individuals.The safe distancing limit estimated with 1 m/s airflow was about 1.8 m.The extensive deposition was observed for distances less than 1.8 m in this study,emphasizing the fact that social distancing advisories are not useful and do not take into account the external dynamics associated with airflow.
文摘Cylindrical Cam Mechanism which is one of the best eq uipments to accomplish an accurate motion transmission is widely used in the fie lds of industries, such as machine tool exchangers, textile machinery and automa tic transfer equipments. This paper proposes a new approach for the shape design and manufacturing of the cylindrical cam. The design approach uses the relative velocity concept and the manufacturing approach uses the inverse kinematics concept. For the shape desig n, the contact points between the cam and the follower roller are calculated bas ed on relative velocity of which the direction is on the common tangential line, and then the whole shape of cam is determined from transformation of the coordi nate system. For the manufacturing procedures, the location and the orientation of cutter path can be allocated corresponding to the designed shape data. The in tegral NC code for multi-axis CNC machining center is created using the inverse kinematics concept from the data of the location and the orientation of cutter path. As the advantages of the proposed approach, the machine tool is designed t o having an alternative size in fabricating the general cam, while the tool must be fitted to diameter size of the follower in the conventional approach. Finally, CAD/CAM program, "Cylindrical DAM", is developed on C++ lan guage. This program can perform shape design, manufacturing and kinematics simul ation, which can make integral NC code for multi-axis CNC machining center. The proposed method can be applied easily on fields of industries.
基金the Fundamental Research Grant Scheme (FRGS),grant No.FRGS/1/2021/TK0/UKM/01/5 funded by the Ministry of Higher Education (MOHE)。
文摘This article delivers a robust overview of potential electrode materials for use in symmetrical solid oxide fuel cells(S-SOFCs),a relatively new SOFC technology.To this end,this article provides a comprehensive review of recent advances and progress in electrode materials for S-SOFC,discussing both the selection of materials and the challenges that come with making that choice.This article discussed the relevant factors involved in developing electrodes with nano/microstructure.Nanocomposites,e.g.,non-cobalt and lithiated materials,are only a few of the electrode types now being researched.Furthermore,the phase structure and microstructure of the produced materials are heavily influenced by the synthesis procedure.Insights into the possibilities and difficulties of the material are discussed.To achieve the desired microstructural features,this article focuses on a synthesis technique that is either the most recent or a better iteration of an existing process.The portion of this analysis that addresses the risks associated with manufacturing and the challenges posed by materials when fabricating S-SOFCs is the most critical.This article also provides important and useful recommendations for the strategic design of electrode materials researchers.
文摘Green cutting has become focus of attention in ecological and environmental protection. Steam is cheap, pollu-tion-free and eco-friendly, and then is a good and economical coolant and lubricant. Steam generator and steam feeding system were developed to generate and feed steam. Comparative experiments were carried out in cutting AA6061-15 vol.% SiC (25 μm particle size), with cubic boron nitride (CBN) insert KB-90 grade under the conditions of compressed air, oil water emulsion, steam as coolant and lubricant, and dry cutting, respectively. The experimental results show that, with steam as coolant and lu-bricant, gradual reduction in the cutting force, friction coefficient, surface roughness and cutting temperature values were observed. Further, there was reduction in built up edge formation. It is proved that use of water steam as coolant and lubricant is environ-mentally friendly.
