Soil disturbance includes the change of stress state and the damage of soil structure.The field testing indices reflect the combined effect of both changes and it is difficult to identify the soil structure disturbanc...Soil disturbance includes the change of stress state and the damage of soil structure.The field testing indices reflect the combined effect of both changes and it is difficult to identify the soil structure disturbance directly from these indices.In the present study,the small-strain shear modulus is used to characterize soil structure disturbance by normalizing the effective stress and void ratio based on Hardin equation.The procedure for evaluating soil sampling disturbance in the field and the further disturbance during the subsequent consolidation process in laboratory test is proposed,and then validated by a case study of soft clay ground.Downhole seismic testing in the field,portable piezoelectric bender elements for the drilled sample and bender elements in triaxial apparatus for the consolidated sample were used to monitor the shear wave velocity of the soil from intact to disturbed and even remolded states.It is found that soil sampling disturbance degree by conventional thin-wall sampler is about 30%according to the proposed procedure,which is slightly higher than that from the modified volume compression method proposed by Hong and Onitsuka(1998).And the additional soil disturbance induced by consolidation in laboratory could reach about 50%when the consolidation pressure is far beyond the structural yield stress,and it follows the plastic volumetric strain quite well.展开更多
This research is concentrated on the longitudinal vibration of a tapered pipe pile considering the vertical support of the surrounding soil and construction disturbance.First,the pile-soil system is partitioned into f...This research is concentrated on the longitudinal vibration of a tapered pipe pile considering the vertical support of the surrounding soil and construction disturbance.First,the pile-soil system is partitioned into finite segments in the vertical direction and the Voigt model is applied to simulate the vertical support of the surrounding soil acting on the pile segment.The surrounding soil is divided into finite ring-shaped zones in the radial direction to consider the construction disturbance.Then,the shear complex stiffness at the pile-soil interface is derived by solving the dynamic equilibrium equation for the soil from the outermost to innermost zone.The displacement impedance at the top of an arbitrary pile segment is obtained by solving the dynamic equilibrium equation for the pile and is combined with the vertical support of the surrounding soil to derive the displacement impedance at the bottom of the upper adjacent segment.Further,the displacement impedance at the pile head is obtained based on the impedance function transfer technique.Finally,the reliability of the proposed solution is verified,followed by a sensitivity analysis concerning the coupling effect of the pile parameters,construction disturbance and the vertical support of the surrounding soil on the displacement impedance of the pile.展开更多
The through-diffusion and membrane behavior testing procedure using a closed-system apparatus has been widely used for concurrent measurement of diffusion and membrane efficiency coefficients of low-permeability clay-...The through-diffusion and membrane behavior testing procedure using a closed-system apparatus has been widely used for concurrent measurement of diffusion and membrane efficiency coefficients of low-permeability clay-based barrier materials.However,the common assumption of perfectly flushing conditions at the specimen boundaries could induce errors in analyses of the diffusion coefficients and membrane efficiencies.In this study,an innovative pseudo three-dimensional(3D)analytical method was proposed to evaluate solute distribution along the boundary surfaces of the soil-porous disks system,considering the non-perfectly flushing conditions.The results were consistent with numerical models under two scenarios considering different inflow/outflow positions.The proposed model has been demonstrated to be an accurate and reliable method to estimate solute distributions along the bound-aries.The calculated membrane efficiency coefficient and diffusion coefficient based on the proposed analytical method are more accurate,resulting in up to 50%less relative error than the traditional approach that adopts the arithmetic mean value of the influent and effluent concentrations.The retar-dation factor of the clay specimen also can be calculated with a revised cumulative mass approach.Finally,the simulated transient solute transport matched with experimental data from a multi-stage through-diffusion and membrane behavior test,validating the accuracy of the proposed method.展开更多
Fault rupture propagation is more complex in the overlying soil with intercalation than in homogeneous soil,and it is challenging to simulate this phenomenon accurately using the finite element method.To address this ...Fault rupture propagation is more complex in the overlying soil with intercalation than in homogeneous soil,and it is challenging to simulate this phenomenon accurately using the finite element method.To address this issue,an improved nonlocal model that incorporates softening modulus modification is proposed.The methodology has the advantage that the solutions are independent of both mesh sizes and characteristic lengths,while maintaining objective softening rates of materials.Using the proposed methodology,a series of numerical simulations are conducted to investigate the effects of different mechanical parameters,such as elastic modulus,friction angle and dilation angle of the soil within the intercalation,as well as the impact of geometries,such as the depth and thickness of the intercalation,on the fault rupture progress.This study not only provides significant insights into the mechanisms of fault rupture propagation,specifically in relation to intercalations,but also shows a great value in promoting the current research on fault rupture.展开更多
This paper reports on two sets of centrifuge model tests of wind turbines in dry sand and saturated sand subjected to earthquake sequences.The wind turbine system is composed of a single pile foundation and a wind tur...This paper reports on two sets of centrifuge model tests of wind turbines in dry sand and saturated sand subjected to earthquake sequences.The wind turbine system is composed of a single pile foundation and a wind turbine.All tests were applied with liquefaction experiments and analysis projects(LEAP)waves to simplify the analysis.The objectives of the tests are to investigate:(1)the influence of earthquake history on the seismic response of wind turbines;(2)the influence of earthquake history on the dynamic pile-soil interaction;and(3)the influence of two different foundation types on the seismic response of wind turbines.The tests indicated that earthquake history has a significant influence on the natural frequency of the pile and the soil around the pile in the saturated sand,but has no obvious influence on the dry sand.The shear modulus of the soil and the acceleration amplification factor of the pile top in both tests increased and the maximum bending moment envelope of the single pile foundation shrunk.The stiffness of the p-y curve in saturated sand was increased by the earthquake history,while that in dry sand was not significantly affected.展开更多
The composite pile consisting of core-pile and surrounding cement-enhanced soil is a promising pile foundation in recent years.However,how and to what extent the cement-enhanced soil influences the ultimate lateral re...The composite pile consisting of core-pile and surrounding cement-enhanced soil is a promising pile foundation in recent years.However,how and to what extent the cement-enhanced soil influences the ultimate lateral resistance has not been fully investigated.In this paper,the ultimate lateral resistance of the composite pile was studied by finite element limit analysis(FELA)and theoretical upper-bound analysis.The results of FELA and theoretical analysis revealed three failure modes of laterally loaded composite piles.The effects of the enhanced soil thickness,strength,and pile-enhanced soil interface characteristics on the ultimate lateral resistance were studied.The results show that increasing the enhanced soil thickness leads to a significant improvement on ultimate lateral resistance factor(N P),and there is a critical thickness beyond which the thickness no longer affects the N P.Increasing the enhanced soil strength induced 6.2%-232.6%increase of N P.However,no noticeable impact was detected when the enhanced soil strength was eight times higher than that of the natural soil.The maximum increment of N P is only 30.5%caused by the increase of interface adhesion factor(a).An empirical model was developed to calculate the N P of the composite pile,and the results show excellent agreement with the analytical results.展开更多
A simplified method is presented for predicting consolidation settlement of soft ground improved by floating soil-cement column on the basis of double soil-layer consolidation theory. Combining the axisymmetric consol...A simplified method is presented for predicting consolidation settlement of soft ground improved by floating soil-cement column on the basis of double soil-layer consolidation theory. Combining the axisymmetric consolidation model and equal strain assumption, the governing equation was derived for the consolidation of clayey subsoil reinforced by soil-cement column. By modifying the boundary condition of the interface between the improved layer and underlying layer on seepage and pore-water pressure, the analytical solution of consolidation of soft ground improved by floating soil-cement column was developed under depth-dependent ramp load. The results of the parameter analysis of consolidation behavior show that the consolidation rate is closely related with the depth replacement ratio by the column and the permeability of upper layer. The influence of column-soil constrained modulus ratio and radius ratio of the influence zone to the column on consolidation is also affected by depth replacement ratio. The column-soil total stress ratio increases with time and approaches the final value accompanied with the dissipation of excess pore water pressure.展开更多
The evaluation and design of stone column improvement ground for liquefaction mitigation is a challenging issue for the state of practice. In this paper, a shear wave velocity-based approach is proposed based on the w...The evaluation and design of stone column improvement ground for liquefaction mitigation is a challenging issue for the state of practice. In this paper, a shear wave velocity-based approach is proposed based on the well-defined correlations of liquefaction resistance(CRR)-shear wave velocity(V_s)-void ratio(e) of sandy soils, and the values of parameters in this approach are recommended for preliminary design purpose when site specific values are not available. The detailed procedures of pre-and post-improvement liquefaction evaluations and stone column design are given. According to this approach, the required level of ground improvement will be met once the target V_s of soil is raised high enough(i.e., no less than the critical velocity) to resist the given earthquake loading according to the CRR-V_s relationship, and then this requirement is transferred to the control of target void ratio(i.e., the critical e) according to the V_s-e relationship. As this approach relies on the densification of the surrounding soil instead of the whole improved ground and is conservative by nature, specific considerations of the densification mechanism and effect are given, and the effects of drainage and reinforcement of stone columns are also discussed. A case study of a thermal power plant in Indonesia is introduced, where the effectiveness of stone column improved ground was evaluated by the proposed V_s-based method and compared with the SPT-based evaluation. This improved ground performed well and experienced no liquefaction during subsequent strong earthquakes.展开更多
The mechanical behavior of sand is very complex, and depends on factors including confining pressure, density, and drainage condition. A soil mass can be contractive or dilative when subjected to shear loading, and ev...The mechanical behavior of sand is very complex, and depends on factors including confining pressure, density, and drainage condition. A soil mass can be contractive or dilative when subjected to shear loading, and eventually reaches an ultimate state, referred to as the critical state in soil mechanics. Conventional approach to explore the mechanical behavior of sand mainly relies on the experimental tests in laboratory. This paper gives an alternative view to this subject using discrete element method (DEM), which has attracted much attention in recent years. The implementation of the DEM is carried out by a series of numerical tests on granular assemblies with varying initial densities and confining pressures, under different test configurations. The results demonstrate that such numerical simulations can produce correct responses of the sand behavior in general, including the critical state response, as compared to experimental observations. In addition, the DEM can further provide details of the microstructure evolutions during shearing processes, and the resulting induced anisotropy can be fully captured and quantified in the particle scale.展开更多
A linear viscoporoelastic model is developed to describe the problem of reflection and transmission of an obliquely incident plane P-wave at the interface between an elastic solid and an unsaturated poroelastic medium...A linear viscoporoelastic model is developed to describe the problem of reflection and transmission of an obliquely incident plane P-wave at the interface between an elastic solid and an unsaturated poroelastic medium, in which the solid matrix is filled with two weakly coupled fluids (liquid and gas). The expressions for the amplitude reflection coefficients and the amplitude transmission coefficients are derived by using the potential method. The present derivation is subsequently applied to study the energy conversions among the incident, reflected, and transmitted wave modes. It is found that the reflection and transmission coefficients in the forms of amplitude ratios and energy ratios are functions of the incident angle, the liquid saturation, the frequency of the incident wave, and the elastic constants of the upper and lower media. Numerical results are presented graphically. The effects of the incident angle, the frequency, and the liquid saturation on the amplitude and the energy reflection and transmission coefficients are discussed. It is verified that in the transmission process, there is no energy dissipation at the interface.展开更多
To investigate the soil behaviors in a direct current field on both spatial and temporal scales, a 1: 5 scale model test was conducted in laboratory to simulate the two-dimensional (2D) electro-osmotic consolidation o...To investigate the soil behaviors in a direct current field on both spatial and temporal scales, a 1: 5 scale model test was conducted in laboratory to simulate the two-dimensional (2D) electro-osmotic consolidation of soft clay foundation. Volume of drainage, intensity, voltage, water content and pH value of water collected in the cathodes were monitored. The pH values of soil and the mass of anodes were measured before and after the test. The test results indicate that the unsaturated state, resultant from fissures induced by the differences in water contents, is favorable to dynamic compaction of soil during electro-osmotic drainage. The results also demonstrate that water content, degree of saturation and electric potential distributions can be used to deduce the electro-osmotic drainage process. Water content of soil decreases first near electrodes, while keeps nearly constant in the center of the model. The area with constant water content is larger than half of the sample surface. Moving anodes towards cathodes by about one third of the electrode spacing is effective to improve the treatment effect after electro-osmosis stops due to the large resistance. Moreover, it is observed that during electro-osmosis, the corrosion rate of anodes becomes smaller, while the variation in pH values of soil near anodes becomes larger.展开更多
The solution of a slope stability problem can be approached by its least upper-bound and maximum lower-bound with high accuracy. The limit equilibrium methods that employ vertical slices imply a lower bound of the fac...The solution of a slope stability problem can be approached by its least upper-bound and maximum lower-bound with high accuracy. The limit equilibrium methods that employ vertical slices imply a lower bound of the factor of safety. It has been successfully extended to the area of active earth pressure analysis that accounts for different input of locations of earth pressure applications. Those methods that employ slices with inclined interfaces give an upper-bound approach to the stability analysis. It enjoys a sound mechanical background and is able to provide accurate solutions of soil plasticity. It has been successfully extended to the area of bearing capacity analysis in which various empirical coefficients are no longer necessary. The 3D upper- and lower-bound methods under this framework have been made possible and show great potential for solving various engineering problems.展开更多
The bender element testing features its in-plane directivity, which allows using bender elements to measure the shear wave velocities in a wider range of in-plane configurations besides the standard tip-to-tip alignme...The bender element testing features its in-plane directivity, which allows using bender elements to measure the shear wave velocities in a wider range of in-plane configurations besides the standard tip-to-tip alignment. This paper proposed a novel bender element testing technique for measuring the horizontal shear wave velocity of soils, where the bender elements are surface- mounted and the axes of the source and receiver elements are parallel to each other. The preliminary tests performed on model ground of silica sand showed that, by properly determining the travel distance and time of the shear waves, the surface-mounted bender elements can perform as accurately as the conventional "tip-to-tip" configuration. Potentially, the present system provides a promising nondestructive tool for characterizing geomaterials and site conditions both in laboratory and in the fields.展开更多
Reliable assessment of the lateral pile–soil interaction is of pronounced importance for the design of mono-pile foundations of offshore wind turbines. As the offshore engineering moves to deeper waters, the diameter...Reliable assessment of the lateral pile–soil interaction is of pronounced importance for the design of mono-pile foundations of offshore wind turbines. As the offshore engineering moves to deeper waters, the diameter of monopiles is getting larger, usually about 5 m and could be up to 8 m, which may lead to partially drained behaviors of sand in the vicinity of the pile and thus imply limitations of conventional design methods in which fully drained conditions were assumed. To shed light on this issue, a fully-coupled finite element model was established using an in-house developed finite element code DBLEAVES, incorporating a cyclic mobility constitutive model that is capable of describing the instantaneous contractive and dilative response of sands simultaneously. Triaxial and centrifuge model tests were conducted to calibrate the constitutive model and validate the pile–soil interaction model respectively. This is followed by a parametric study primarily focusing on the effects of loading rates. The initial stiffness of the p–y curve was found to increase with the loading rate whilst the bearing capacity showed the inverse,and the mechanism behind this phenomenon is examined in detail. Then an explicit model was developed to evaluate the development of excess pore pressure in the pile front upon lateral loading, and an upper boundary of normalized loading rate was identified to distinguish fully and partially drained conditions.展开更多
Tortuosity is an important parameter used in areas such as vascular medicine,neurobiology,and the field of soil permeability and diffusion to express the mass transport in porous media.It is a function of the porosity...Tortuosity is an important parameter used in areas such as vascular medicine,neurobiology,and the field of soil permeability and diffusion to express the mass transport in porous media.It is a function of the porosity and the shape and distribution of particles.In this paper,the tortuosity of cubic particles is calculated.With the assumption that the porous medium is homogeneous,the problem is converted to the micro-level over a unit cell,and geometry models of flow paths are proposed.In three-dimensional(3D) cells,the flow paths are too complicated to define.Hence,the 3D models are converted to two-dimensional(2D) models to simplify the calculation process.It is noticed that the path in the 2D model is shorter than that in the 3D model.As a result,triangular particles and the interaction are also taken into consideration to account for the longer distance respectively.We have proposed quadrate particle and interaction(QI) and quadrate and triangular particle(QT) models with cubic particles.Both models have shown good agreement with the experimental data.It is also found that they can predict the toruosities of some kinds of porous media,like freshwater sediment and Negev chalk.展开更多
Natural soils are more durable than almost all man-made materials. Evapotranspiration(ET) covers use vegetated soil layers to store water until it is either evaporated from the soil surface or transpired through veget...Natural soils are more durable than almost all man-made materials. Evapotranspiration(ET) covers use vegetated soil layers to store water until it is either evaporated from the soil surface or transpired through vegetation. ETcovers rely on the water storage capacity of soil layer, rather than low permeability materials, to minimize percolation. While the use of ETcovers in landfills increased over the last decade, they were mainly used in arid or semi-arid regions. At present, the use of ET covers has not been thoroughly investigated in humid areas. The purpose of this paper is to investigate the use of ET covers in humid areas where there is an annual precipitation of more than 800 mm. Numerical analyses were carried out to investigate the influences of cover thickness, soil type, vegetation level and distribution of precipitation on performance of ET covers.Performance and applicability of capillary barriers and a new-type cover were analyzed. The results show that percolation decreases with an increasing cover thickness and an increasing vegetation level, but the increasing trend becomes unclear when certain thickness or LAI(leaf area index) is reached. Cover soil with a large capability of water storage is recommended to minimize percolation. ET covers are significantly influenced by distribution of precipitation and are more effective in areas where rainy season coincides with hot season. Capillary barriers are more efficient than monolithic covers. The new cover is better than the monolithic cover in performance and the final percolation is only 0.5% of the annual precipitation.展开更多
Damage and threats to hydraulic and submarine structures by underwater explosions(UNDEXs)have raised much attention.The centrifuge model test,compared to prototype test,is a more promising way to examine the problem w...Damage and threats to hydraulic and submarine structures by underwater explosions(UNDEXs)have raised much attention.The centrifuge model test,compared to prototype test,is a more promising way to examine the problem while reducing cost and satisfying the similitude requirements of both Mach and Froude numbers simultaneously.This study used a systematic approach employing centrifuge model tests and numerical simulations to investigate the effects of UNDEXs on an air-backed steel plate.Nineteen methodical centrifuge tests of UNDEXs were conducted.The shock wave pressure,bubble oscillation pressure,acceleration and the strain of the air-backed steel plate were recorded and compared with numerical studies using the finite element analysis(FEA)commercial software ABAQUS.By implementing empirically derived and physically measured pressures into the numerical models,the effects of the shock wave and bubble oscillation on the steel plate were investigated.Generally,the numerical results were in agreement with the experimental results.These results showed that the peak pressure of an UNDEX has a significant effect on the peak acceleration of the steel plate and that the impulse of the UNDEX pressure governs the peak strain of the steel plate.展开更多
Based on polarization mechanisms, such as electronic, ionic and orientational polarizations, a new equation for dielectric permittivity of soil is proposed to interpret the dielectric behavior of a mixture like soil, ...Based on polarization mechanisms, such as electronic, ionic and orientational polarizations, a new equation for dielectric permittivity of soil is proposed to interpret the dielectric behavior of a mixture like soil, in terms of polarization process of its components and the interactions between its components. The dielectric permittivity is expressed in terms of a fre-quency-dependent part and a frequency-independent part. These two parts correspond to polarizations occurred at different fre-quency range. It is a new volumetric mixing model with theoretical background. Based on time domain reflectometry (TDR) measurements of saturated soil samples and test data from literature, comparisons of this model with some well established mixing models show that the curves for saturated sand soils and slurries resulted from the new equation, which agree well with TDR measurements, are close to those calculated from Birchak's model.展开更多
This paper performed flexural test and numerical simulation of clay-beams with different water contents to study the tensile fracture of clay soil and the relevant mechanisms.The crack initiation and propagation proce...This paper performed flexural test and numerical simulation of clay-beams with different water contents to study the tensile fracture of clay soil and the relevant mechanisms.The crack initiation and propagation process and the accompanied strain localization behaviors were all clearly observed and analyzed.The exponential cohesive zone model was proposed to simulate the crack interface behavior of the cohesive-frictional materials.The experimental results show that the bending capacity of clay-beams decrease with the water content,while those of the crack mouth opening displacement,crack-tip strain and the strain localization range increase.The numerical predictions successfully reproduce the evolving tensile cracks and the strain localization phenomenon of the clay beams with different fracture ductility,which demonstrates the validity of the proposed cohesive zone model in modelling clay fractures.展开更多
Soil strain is the key parameter to control the elasto-plastic deformation and even the failure processes.To overcome the defect that the strain of the model soil is always smaller than that of the prototype in Iai′s...Soil strain is the key parameter to control the elasto-plastic deformation and even the failure processes.To overcome the defect that the strain of the model soil is always smaller than that of the prototype in Iai′s generalized scaling law(GSL),a modified scaling law was proposed based on Iai′s GSL to secure the same dynamic shear strain between the centrifuge model and the prototype by modulating the amplitude and frequency of the input motion at the base.A suite of dynamic centrifuge model tests of dry sand level ground was conducted with the same overall scaling factor(λ=200)under different centrifugal accelerations by using the technique of“modeling of models”to validate the modified GSL.The test results show that the modified GSL could achieve the same dynamic strain in model as that of the prototype,leading to better modeling for geotechnical problems where dynamic strain dominates the response or failure of soils.Finally,the applicability of the proposed scaling law and possible constraints on geometry scaling due to the capability limits of existing centrifuge shaking tables are discussed.展开更多
基金This study is partly supported by the National Natural Science Foundation of China(Grant Nos.51978613,52278374 and 51988101).All these funding grants are greatly acknowledged.
文摘Soil disturbance includes the change of stress state and the damage of soil structure.The field testing indices reflect the combined effect of both changes and it is difficult to identify the soil structure disturbance directly from these indices.In the present study,the small-strain shear modulus is used to characterize soil structure disturbance by normalizing the effective stress and void ratio based on Hardin equation.The procedure for evaluating soil sampling disturbance in the field and the further disturbance during the subsequent consolidation process in laboratory test is proposed,and then validated by a case study of soft clay ground.Downhole seismic testing in the field,portable piezoelectric bender elements for the drilled sample and bender elements in triaxial apparatus for the consolidated sample were used to monitor the shear wave velocity of the soil from intact to disturbed and even remolded states.It is found that soil sampling disturbance degree by conventional thin-wall sampler is about 30%according to the proposed procedure,which is slightly higher than that from the modified volume compression method proposed by Hong and Onitsuka(1998).And the additional soil disturbance induced by consolidation in laboratory could reach about 50%when the consolidation pressure is far beyond the structural yield stress,and it follows the plastic volumetric strain quite well.
基金National Natural Science Foundation of China under Grand No.51808190the Central Government Guides Local Science and Technology Development Fund Projects under Grand No.XZ202301YD0019C+2 种基金the Foundation of Key Laboratory of Soft Soils and Geoenvironmental Engineering(Zhejiang University)Ministry of Education under Grand No.2022P04the Central University Basic Research Fund of China under Grand No.B220202017。
文摘This research is concentrated on the longitudinal vibration of a tapered pipe pile considering the vertical support of the surrounding soil and construction disturbance.First,the pile-soil system is partitioned into finite segments in the vertical direction and the Voigt model is applied to simulate the vertical support of the surrounding soil acting on the pile segment.The surrounding soil is divided into finite ring-shaped zones in the radial direction to consider the construction disturbance.Then,the shear complex stiffness at the pile-soil interface is derived by solving the dynamic equilibrium equation for the soil from the outermost to innermost zone.The displacement impedance at the top of an arbitrary pile segment is obtained by solving the dynamic equilibrium equation for the pile and is combined with the vertical support of the surrounding soil to derive the displacement impedance at the bottom of the upper adjacent segment.Further,the displacement impedance at the pile head is obtained based on the impedance function transfer technique.Finally,the reliability of the proposed solution is verified,followed by a sensitivity analysis concerning the coupling effect of the pile parameters,construction disturbance and the vertical support of the surrounding soil on the displacement impedance of the pile.
基金The financial support received from the Ministry of Science and Technology of the People’s Republic of China(Grant No.2019YFC1806002)National Natural Science Foundation of China(Grant Nos.42107174,42077241)is gratefully acknowledged.
文摘The through-diffusion and membrane behavior testing procedure using a closed-system apparatus has been widely used for concurrent measurement of diffusion and membrane efficiency coefficients of low-permeability clay-based barrier materials.However,the common assumption of perfectly flushing conditions at the specimen boundaries could induce errors in analyses of the diffusion coefficients and membrane efficiencies.In this study,an innovative pseudo three-dimensional(3D)analytical method was proposed to evaluate solute distribution along the boundary surfaces of the soil-porous disks system,considering the non-perfectly flushing conditions.The results were consistent with numerical models under two scenarios considering different inflow/outflow positions.The proposed model has been demonstrated to be an accurate and reliable method to estimate solute distributions along the bound-aries.The calculated membrane efficiency coefficient and diffusion coefficient based on the proposed analytical method are more accurate,resulting in up to 50%less relative error than the traditional approach that adopts the arithmetic mean value of the influent and effluent concentrations.The retar-dation factor of the clay specimen also can be calculated with a revised cumulative mass approach.Finally,the simulated transient solute transport matched with experimental data from a multi-stage through-diffusion and membrane behavior test,validating the accuracy of the proposed method.
基金supported by the National Natural Science Foundation of China(Grant Nos.51988101 and 42007262).
文摘Fault rupture propagation is more complex in the overlying soil with intercalation than in homogeneous soil,and it is challenging to simulate this phenomenon accurately using the finite element method.To address this issue,an improved nonlocal model that incorporates softening modulus modification is proposed.The methodology has the advantage that the solutions are independent of both mesh sizes and characteristic lengths,while maintaining objective softening rates of materials.Using the proposed methodology,a series of numerical simulations are conducted to investigate the effects of different mechanical parameters,such as elastic modulus,friction angle and dilation angle of the soil within the intercalation,as well as the impact of geometries,such as the depth and thickness of the intercalation,on the fault rupture progress.This study not only provides significant insights into the mechanisms of fault rupture propagation,specifically in relation to intercalations,but also shows a great value in promoting the current research on fault rupture.
基金Basic Science Center Program for Multiphase Media Evolution in Hypergravity of the National Natural Science Foundation of China under Grant No.51988101the National Natural Science Foundation of China under Grant No.51808490。
文摘This paper reports on two sets of centrifuge model tests of wind turbines in dry sand and saturated sand subjected to earthquake sequences.The wind turbine system is composed of a single pile foundation and a wind turbine.All tests were applied with liquefaction experiments and analysis projects(LEAP)waves to simplify the analysis.The objectives of the tests are to investigate:(1)the influence of earthquake history on the seismic response of wind turbines;(2)the influence of earthquake history on the dynamic pile-soil interaction;and(3)the influence of two different foundation types on the seismic response of wind turbines.The tests indicated that earthquake history has a significant influence on the natural frequency of the pile and the soil around the pile in the saturated sand,but has no obvious influence on the dry sand.The shear modulus of the soil and the acceleration amplification factor of the pile top in both tests increased and the maximum bending moment envelope of the single pile foundation shrunk.The stiffness of the p-y curve in saturated sand was increased by the earthquake history,while that in dry sand was not significantly affected.
基金The work was supported by the National Natural Science Foundation of China(Grant No.51978540).
文摘The composite pile consisting of core-pile and surrounding cement-enhanced soil is a promising pile foundation in recent years.However,how and to what extent the cement-enhanced soil influences the ultimate lateral resistance has not been fully investigated.In this paper,the ultimate lateral resistance of the composite pile was studied by finite element limit analysis(FELA)and theoretical upper-bound analysis.The results of FELA and theoretical analysis revealed three failure modes of laterally loaded composite piles.The effects of the enhanced soil thickness,strength,and pile-enhanced soil interface characteristics on the ultimate lateral resistance were studied.The results show that increasing the enhanced soil thickness leads to a significant improvement on ultimate lateral resistance factor(N P),and there is a critical thickness beyond which the thickness no longer affects the N P.Increasing the enhanced soil strength induced 6.2%-232.6%increase of N P.However,no noticeable impact was detected when the enhanced soil strength was eight times higher than that of the natural soil.The maximum increment of N P is only 30.5%caused by the increase of interface adhesion factor(a).An empirical model was developed to calculate the N P of the composite pile,and the results show excellent agreement with the analytical results.
基金Project(51278450)supported by the National Natural Science Foundation of China
文摘A simplified method is presented for predicting consolidation settlement of soft ground improved by floating soil-cement column on the basis of double soil-layer consolidation theory. Combining the axisymmetric consolidation model and equal strain assumption, the governing equation was derived for the consolidation of clayey subsoil reinforced by soil-cement column. By modifying the boundary condition of the interface between the improved layer and underlying layer on seepage and pore-water pressure, the analytical solution of consolidation of soft ground improved by floating soil-cement column was developed under depth-dependent ramp load. The results of the parameter analysis of consolidation behavior show that the consolidation rate is closely related with the depth replacement ratio by the column and the permeability of upper layer. The influence of column-soil constrained modulus ratio and radius ratio of the influence zone to the column on consolidation is also affected by depth replacement ratio. The column-soil total stress ratio increases with time and approaches the final value accompanied with the dissipation of excess pore water pressure.
基金National Natural Science Foundation of China under Grant No.51578501 and No.51127005the Foundation for the Author of National Excellent Doctoral Dissertation of P R China under Grant No.201160+3 种基金the Zhejiang Provincial Natural Science Foundation of China under Grant No.LR15E080001the National Basic Research Program of China(973 Project)under Grant No.2014CB047005the Fundamental Research Funds for the Central Universities under Grant No.2014FZA4016Zhejiang University K.P.Chao’s High Technology Development Foundation(2014)
文摘The evaluation and design of stone column improvement ground for liquefaction mitigation is a challenging issue for the state of practice. In this paper, a shear wave velocity-based approach is proposed based on the well-defined correlations of liquefaction resistance(CRR)-shear wave velocity(V_s)-void ratio(e) of sandy soils, and the values of parameters in this approach are recommended for preliminary design purpose when site specific values are not available. The detailed procedures of pre-and post-improvement liquefaction evaluations and stone column design are given. According to this approach, the required level of ground improvement will be met once the target V_s of soil is raised high enough(i.e., no less than the critical velocity) to resist the given earthquake loading according to the CRR-V_s relationship, and then this requirement is transferred to the control of target void ratio(i.e., the critical e) according to the V_s-e relationship. As this approach relies on the densification of the surrounding soil instead of the whole improved ground and is conservative by nature, specific considerations of the densification mechanism and effect are given, and the effects of drainage and reinforcement of stone columns are also discussed. A case study of a thermal power plant in Indonesia is introduced, where the effectiveness of stone column improved ground was evaluated by the proposed V_s-based method and compared with the SPT-based evaluation. This improved ground performed well and experienced no liquefaction during subsequent strong earthquakes.
基金the National Natural Science Foundation of China (Nos. 10725210 and 50509021)the Postdoctoral Foundations in China (No. 20070421202)+1 种基金the Program for New Century Excellent Talents in University in China (No. NCET-05-05010)the Com-petitive Postdoctoral Research Project in Zhejiang Province, China
文摘The mechanical behavior of sand is very complex, and depends on factors including confining pressure, density, and drainage condition. A soil mass can be contractive or dilative when subjected to shear loading, and eventually reaches an ultimate state, referred to as the critical state in soil mechanics. Conventional approach to explore the mechanical behavior of sand mainly relies on the experimental tests in laboratory. This paper gives an alternative view to this subject using discrete element method (DEM), which has attracted much attention in recent years. The implementation of the DEM is carried out by a series of numerical tests on granular assemblies with varying initial densities and confining pressures, under different test configurations. The results demonstrate that such numerical simulations can produce correct responses of the sand behavior in general, including the critical state response, as compared to experimental observations. In addition, the DEM can further provide details of the microstructure evolutions during shearing processes, and the resulting induced anisotropy can be fully captured and quantified in the particle scale.
文摘A linear viscoporoelastic model is developed to describe the problem of reflection and transmission of an obliquely incident plane P-wave at the interface between an elastic solid and an unsaturated poroelastic medium, in which the solid matrix is filled with two weakly coupled fluids (liquid and gas). The expressions for the amplitude reflection coefficients and the amplitude transmission coefficients are derived by using the potential method. The present derivation is subsequently applied to study the energy conversions among the incident, reflected, and transmitted wave modes. It is found that the reflection and transmission coefficients in the forms of amplitude ratios and energy ratios are functions of the incident angle, the liquid saturation, the frequency of the incident wave, and the elastic constants of the upper and lower media. Numerical results are presented graphically. The effects of the incident angle, the frequency, and the liquid saturation on the amplitude and the energy reflection and transmission coefficients are discussed. It is verified that in the transmission process, there is no energy dissipation at the interface.
基金Supported by the National Natural Science Foundation of China (50879076)
文摘To investigate the soil behaviors in a direct current field on both spatial and temporal scales, a 1: 5 scale model test was conducted in laboratory to simulate the two-dimensional (2D) electro-osmotic consolidation of soft clay foundation. Volume of drainage, intensity, voltage, water content and pH value of water collected in the cathodes were monitored. The pH values of soil and the mass of anodes were measured before and after the test. The test results indicate that the unsaturated state, resultant from fissures induced by the differences in water contents, is favorable to dynamic compaction of soil during electro-osmotic drainage. The results also demonstrate that water content, degree of saturation and electric potential distributions can be used to deduce the electro-osmotic drainage process. Water content of soil decreases first near electrodes, while keeps nearly constant in the center of the model. The area with constant water content is larger than half of the sample surface. Moving anodes towards cathodes by about one third of the electrode spacing is effective to improve the treatment effect after electro-osmosis stops due to the large resistance. Moreover, it is observed that during electro-osmosis, the corrosion rate of anodes becomes smaller, while the variation in pH values of soil near anodes becomes larger.
基金Project (Nos. 50539100,50679035 and 50509027) supported by the National Natural ScienceFoundation of China
文摘The solution of a slope stability problem can be approached by its least upper-bound and maximum lower-bound with high accuracy. The limit equilibrium methods that employ vertical slices imply a lower bound of the factor of safety. It has been successfully extended to the area of active earth pressure analysis that accounts for different input of locations of earth pressure applications. Those methods that employ slices with inclined interfaces give an upper-bound approach to the stability analysis. It enjoys a sound mechanical background and is able to provide accurate solutions of soil plasticity. It has been successfully extended to the area of bearing capacity analysis in which various empirical coefficients are no longer necessary. The 3D upper- and lower-bound methods under this framework have been made possible and show great potential for solving various engineering problems.
基金Project supported by the National Basic Research Program (973) of China (No. 2007CB714203)the China Postdoctoral Science Foun-dation (No. 20080430219)partly supported by the Foundation for Seismological Researches, China Earthquake Administration (No. 200808022)
文摘The bender element testing features its in-plane directivity, which allows using bender elements to measure the shear wave velocities in a wider range of in-plane configurations besides the standard tip-to-tip alignment. This paper proposed a novel bender element testing technique for measuring the horizontal shear wave velocity of soils, where the bender elements are surface- mounted and the axes of the source and receiver elements are parallel to each other. The preliminary tests performed on model ground of silica sand showed that, by properly determining the travel distance and time of the shear waves, the surface-mounted bender elements can perform as accurately as the conventional "tip-to-tip" configuration. Potentially, the present system provides a promising nondestructive tool for characterizing geomaterials and site conditions both in laboratory and in the fields.
基金financially supported by the National Natural Science Foundation of China (Grant Nos. 51988101 and 51679211)。
文摘Reliable assessment of the lateral pile–soil interaction is of pronounced importance for the design of mono-pile foundations of offshore wind turbines. As the offshore engineering moves to deeper waters, the diameter of monopiles is getting larger, usually about 5 m and could be up to 8 m, which may lead to partially drained behaviors of sand in the vicinity of the pile and thus imply limitations of conventional design methods in which fully drained conditions were assumed. To shed light on this issue, a fully-coupled finite element model was established using an in-house developed finite element code DBLEAVES, incorporating a cyclic mobility constitutive model that is capable of describing the instantaneous contractive and dilative response of sands simultaneously. Triaxial and centrifuge model tests were conducted to calibrate the constitutive model and validate the pile–soil interaction model respectively. This is followed by a parametric study primarily focusing on the effects of loading rates. The initial stiffness of the p–y curve was found to increase with the loading rate whilst the bearing capacity showed the inverse,and the mechanism behind this phenomenon is examined in detail. Then an explicit model was developed to evaluate the development of excess pore pressure in the pile front upon lateral loading, and an upper boundary of normalized loading rate was identified to distinguish fully and partially drained conditions.
基金Project supported by the Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20090101110075)the Key Innovation Team Support Project of Zhejiang Province,China (Grant No. 2009R50050)
文摘Tortuosity is an important parameter used in areas such as vascular medicine,neurobiology,and the field of soil permeability and diffusion to express the mass transport in porous media.It is a function of the porosity and the shape and distribution of particles.In this paper,the tortuosity of cubic particles is calculated.With the assumption that the porous medium is homogeneous,the problem is converted to the micro-level over a unit cell,and geometry models of flow paths are proposed.In three-dimensional(3D) cells,the flow paths are too complicated to define.Hence,the 3D models are converted to two-dimensional(2D) models to simplify the calculation process.It is noticed that the path in the 2D model is shorter than that in the 3D model.As a result,triangular particles and the interaction are also taken into consideration to account for the longer distance respectively.We have proposed quadrate particle and interaction(QI) and quadrate and triangular particle(QT) models with cubic particles.Both models have shown good agreement with the experimental data.It is also found that they can predict the toruosities of some kinds of porous media,like freshwater sediment and Negev chalk.
基金funded by the National Natural Science Foundation of China (51178260)Open Project of MOE Key Laboratory of Soft Soil and Geoenvironmental Engineering, Zhejiang University (2011P02)
文摘Natural soils are more durable than almost all man-made materials. Evapotranspiration(ET) covers use vegetated soil layers to store water until it is either evaporated from the soil surface or transpired through vegetation. ETcovers rely on the water storage capacity of soil layer, rather than low permeability materials, to minimize percolation. While the use of ETcovers in landfills increased over the last decade, they were mainly used in arid or semi-arid regions. At present, the use of ET covers has not been thoroughly investigated in humid areas. The purpose of this paper is to investigate the use of ET covers in humid areas where there is an annual precipitation of more than 800 mm. Numerical analyses were carried out to investigate the influences of cover thickness, soil type, vegetation level and distribution of precipitation on performance of ET covers.Performance and applicability of capillary barriers and a new-type cover were analyzed. The results show that percolation decreases with an increasing cover thickness and an increasing vegetation level, but the increasing trend becomes unclear when certain thickness or LAI(leaf area index) is reached. Cover soil with a large capability of water storage is recommended to minimize percolation. ET covers are significantly influenced by distribution of precipitation and are more effective in areas where rainy season coincides with hot season. Capillary barriers are more efficient than monolithic covers. The new cover is better than the monolithic cover in performance and the final percolation is only 0.5% of the annual precipitation.
基金The authors would like to thank Prof.Guowei Ma,Prof.Fang Wang,and Prof.Hongyuan Zhou for critically reading and revising the manuscript as well as for helpful discussions.This study has been financially supported by the State Key Program of National Natural Science Foundation of China(Grant No.51339006).
文摘Damage and threats to hydraulic and submarine structures by underwater explosions(UNDEXs)have raised much attention.The centrifuge model test,compared to prototype test,is a more promising way to examine the problem while reducing cost and satisfying the similitude requirements of both Mach and Froude numbers simultaneously.This study used a systematic approach employing centrifuge model tests and numerical simulations to investigate the effects of UNDEXs on an air-backed steel plate.Nineteen methodical centrifuge tests of UNDEXs were conducted.The shock wave pressure,bubble oscillation pressure,acceleration and the strain of the air-backed steel plate were recorded and compared with numerical studies using the finite element analysis(FEA)commercial software ABAQUS.By implementing empirically derived and physically measured pressures into the numerical models,the effects of the shock wave and bubble oscillation on the steel plate were investigated.Generally,the numerical results were in agreement with the experimental results.These results showed that the peak pressure of an UNDEX has a significant effect on the peak acceleration of the steel plate and that the impulse of the UNDEX pressure governs the peak strain of the steel plate.
基金Project (Nos. 50278087 and 50308026) supported by the NationalNatural Science Foundation of China
文摘Based on polarization mechanisms, such as electronic, ionic and orientational polarizations, a new equation for dielectric permittivity of soil is proposed to interpret the dielectric behavior of a mixture like soil, in terms of polarization process of its components and the interactions between its components. The dielectric permittivity is expressed in terms of a fre-quency-dependent part and a frequency-independent part. These two parts correspond to polarizations occurred at different fre-quency range. It is a new volumetric mixing model with theoretical background. Based on time domain reflectometry (TDR) measurements of saturated soil samples and test data from literature, comparisons of this model with some well established mixing models show that the curves for saturated sand soils and slurries resulted from the new equation, which agree well with TDR measurements, are close to those calculated from Birchak's model.
基金sponsored by the National Key Research and Development Program of China(No.2016YFC0800200)the National Basic Research Program of China(No.2014CB047000),and the NSFC(Grant No.51578502).
文摘This paper performed flexural test and numerical simulation of clay-beams with different water contents to study the tensile fracture of clay soil and the relevant mechanisms.The crack initiation and propagation process and the accompanied strain localization behaviors were all clearly observed and analyzed.The exponential cohesive zone model was proposed to simulate the crack interface behavior of the cohesive-frictional materials.The experimental results show that the bending capacity of clay-beams decrease with the water content,while those of the crack mouth opening displacement,crack-tip strain and the strain localization range increase.The numerical predictions successfully reproduce the evolving tensile cracks and the strain localization phenomenon of the clay beams with different fracture ductility,which demonstrates the validity of the proposed cohesive zone model in modelling clay fractures.
基金National Natural Science Foundation of China under Grant Nos.51988101,51978613 and 52278374the Chinese Program of Introducing Talents of Discipline to University(the 111 Project,B18047)。
文摘Soil strain is the key parameter to control the elasto-plastic deformation and even the failure processes.To overcome the defect that the strain of the model soil is always smaller than that of the prototype in Iai′s generalized scaling law(GSL),a modified scaling law was proposed based on Iai′s GSL to secure the same dynamic shear strain between the centrifuge model and the prototype by modulating the amplitude and frequency of the input motion at the base.A suite of dynamic centrifuge model tests of dry sand level ground was conducted with the same overall scaling factor(λ=200)under different centrifugal accelerations by using the technique of“modeling of models”to validate the modified GSL.The test results show that the modified GSL could achieve the same dynamic strain in model as that of the prototype,leading to better modeling for geotechnical problems where dynamic strain dominates the response or failure of soils.Finally,the applicability of the proposed scaling law and possible constraints on geometry scaling due to the capability limits of existing centrifuge shaking tables are discussed.
