Non-equilibrium solidification structures of Cu55Ni45 and Cu55Ni43Co2 alloys were prepared by the molten glass purification cycle superheating method.The variation of the recalescence phenomenon with the degree of und...Non-equilibrium solidification structures of Cu55Ni45 and Cu55Ni43Co2 alloys were prepared by the molten glass purification cycle superheating method.The variation of the recalescence phenomenon with the degree of undercooling in the rapid solidification process was investigated using an infrared thermometer.The addition of the Co element affected the evolution of the recalescence phenomenon in Cu-Ni alloys.The images of the solid-liquid interface migration during the rapid solidification of supercooled melts were captured by using a high-speed camera.The solidification rate of Cu-Ni alloys,with the addition of Co elements,was explored.Finally,the grain refinement structure with low supercooling was characterised using electron backscatter diffraction(EBSD).The effect of Co on the microstructural evolution during nonequilibrium solidification of Cu-Ni alloys under conditions of small supercooling is investigated by comparing the microstructures of Cu55Ni45 and Cu55Ni43Co2 alloys.The experimental results show that the addition of a small amount of Co weakens the recalescence behaviour of the Cu55Ni45 alloy and significantly reduces the thermal strain in the rapid solidification phase.In the rapid solidification phase,the thermal strain is greatly reduced,and there is a significant increase in the characteristic undercooling degree.Furthermore,the addition of Co and the reduction of Cu not only result in a lower solidification rate of the alloy,but also contribute to the homogenisation of the grain size.展开更多
The aim of the study was to investigate the effect of different surface treatment of titanium(Ti)on the adhesion test results for dental application.Ti substrates roughened by 400 to 1500-grit SiC polish papers and al...The aim of the study was to investigate the effect of different surface treatment of titanium(Ti)on the adhesion test results for dental application.Ti substrates roughened by 400 to 1500-grit SiC polish papers and alumina blasting,alkali treated by 5 molar(M)NaOH and KOH solutions and heat treated at the temperature range of 400-800℃were used in this study.The treated samples were subjected to the adhesion test.According to the results of the adhesion test,the adhesive strength showed the highest value for the blasted titanium among all polished and blasted samples.The Ti samples heated at 650℃showed the highest adhesive strength among all heat-treated samples.Further,the adhesion test results indicated the higher adhesive strength of chemically treated samples treated by NaOH rather than that by KOH.The polished and heated Ti samples showed the highest adhesive strength among all samples.展开更多
Engineered cardiac constructs(ECC)aid in the progression of regenerative medicine,disease modeling and targeted drug delivery to adjust and aim the release of remedial combination as well as decrease the side effects ...Engineered cardiac constructs(ECC)aid in the progression of regenerative medicine,disease modeling and targeted drug delivery to adjust and aim the release of remedial combination as well as decrease the side effects of drugs.In this research,polycaprolactone/gold nanoparticles(PCL/GNPs)three-dimensional(3D)composite scaffolds were manufactured by 3D printing using the fused deposition modeling(FDM)method and then coated with gelatin/spironolactone(GEL/SPL).Scanning electron microscopy(SEM)and Fourier transform-infrared spectroscopy(FTIR–ATR)were applied to characterize the samples.Furthermore,drug release,biodegradation,behavior of the myoblasts(H9C2)cell line,and cytotoxicity of the 3D scaffolds were evaluated.The microstructural observation of the scaffolds reported interconnected pores with 150–300µm in diameter.The 3D scaffolds were degraded significantly after 28 days of immersion in stimulated body fluid(SBF),with the maximum rate of GEL-coated 3D scaffolds.SPL release from cross-linked GEL coating demonstrated the excess of drug release over time,and according to the control release systems,the drug delivery systems(DDS)went into balance after the 14th day.In addition,cell culture study showed that with the addition of GNPs,the proliferation of(H9C2)was enhanced,and with GEL/SPL coating the cell attachment and viability were improved significantly.These findings suggested that PCL/GNPs 3D scaffolds coated with GEL/SPL can be an appropriate choice for myocardial tissue engineering.展开更多
Graphene oxide has been used widely as a starting precursor for applications that cater to the needs of tunable graphene. However, the hydrophilic characteristic limits their application, especially in a hydrophobic c...Graphene oxide has been used widely as a starting precursor for applications that cater to the needs of tunable graphene. However, the hydrophilic characteristic limits their application, especially in a hydrophobic condition. Herein, a novel non-covalent surface modification approach towards graphene oxide was conducted via a UV-induced photo-polymerization technique that involves two major routes; a UV-sensitive initiator embedded via pi-pi interactions on the graphene planar rings, and the polymerization of hydrophobic polymeric chains along the surface. The functionalized graphene oxide successfully achieved the desired hydrophobicity as it displayed the characteristic of being readily dissolved in organic solvent. Upon its addition into a polymeric solution and subjected to an electrospinning process,non-woven random nanofibers embedded with graphene oxide sheets were obtained. The prepared polymeric nanofibers were subjected to two-step thermal treatments that eventually converted the polymeric chains into a carbon-rich conductive structure. A unique morphology was observed upon the addition of the functionalized graphene oxide, whereby the sheets were embedded and intercalated within the carbon nanofibers and formed a continuous structure. This reinforcement effectively enhanced the electrochemical performance of the carbon nanofibers by recording a specific capacitance of up to 140.10 F/g at the current density of 1 A/g, which was approximately three folds more than that of pristine nanofibers.It also retained the capacitance up to 96.2% after 1000 vigorous charge/discharge cycles. This functionalization technique opens up a new pathway in tuning the solubility nature of graphene oxide towards the synthesis of a graphene oxide-reinforced polymeric structure.展开更多
Arsenic is a natural tasteless and odourless element,existing in the earth's crust at average levels of between two and five thousands micrograms per liter (parts per million) . Arsenic is highly toxic to humans, ...Arsenic is a natural tasteless and odourless element,existing in the earth's crust at average levels of between two and five thousands micrograms per liter (parts per million) . Arsenic is highly toxic to humans, who are exposed to it primarily from air,food and water. The occurrence of arsenic in groundwater is due to geological composition of soil. High concentrations of arsenic in water are the result of dissolution or desorption of ferric oxides and the oxidation of mineral arsenopyrites. Arsenic in drinking water has an important impact on the human health,especially in the less developed countries. Different methods exist to remove arsenic from aquatic media,and one of them is by adsorption. In this work,the adsorption of both As(III) and As(V) by means of novel microspheres has been investigated. In particular,TiO2 has been embedded into polymeric microspheres PES (PolyEtherSulphone) and PEEK-WC (PolyEtherEther-Ketone) . The main advantages of this encapsulation adsorption material are: no loss of adsorbents into the water stream,easy to be used and scaled-up.展开更多
Crack growth modeling has always been one of the major challenges in fracture mechanics.Among all numerical methods,the extended finite element method(XFEM)has recently attracted much attention due to its ability to e...Crack growth modeling has always been one of the major challenges in fracture mechanics.Among all numerical methods,the extended finite element method(XFEM)has recently attracted much attention due to its ability to estimate the discontinuous deformation field.However,XFEM modeling does not directly lead to reliable results,and choosing a strategy of implementation is inevitable,especially in porous media.In this study,two prevalent XFEM strategies are evaluated:a)applying reduced Young’s modulus to pores and b)using different partitions to the model and enriching each part individually.We mention the advantages and limitations of each strategy via both analytical and experimental validations.Finally,the crack growth is modeled in a natural porous media(Fontainebleau sandstone).Our investigations proved that although both strategies can identically predict the stress distribution in the sample,the first strategy simulates only the initial crack propagation,while the second strategy could model multiple cracks growths.Both strategies are reliable and highly accurate in calculating the stress intensity factor,but the second strategy can compute a more reliable reaction force.Experimental tests showed that the second strategy is a more accurate strategy in predicting the preferred crack growth path and determining the maximum strength of the sample.展开更多
In this study,nano-biocomposites of polycaprolactone(PCL)as the matrix and different amounts of nanofluorapatite(nFA)(0,10,20 and 30 wt.%)as the reinforcement were prepared for possible scaffold fabrication using the ...In this study,nano-biocomposites of polycaprolactone(PCL)as the matrix and different amounts of nanofluorapatite(nFA)(0,10,20 and 30 wt.%)as the reinforcement were prepared for possible scaffold fabrication using the fused filament fabrication(FFF)3D printer.Field Emission Scanning Electron Microscopy(FE-SEM)and Energy Dispersive Spectroscopy(EDS)showed that nFA particles were well distributed in the PCL matrix.X-ray diffraction analysis(XRD)and Fourier Transform Infrared Spectroscopy(FTIR)depicted no chemical interaction between the elements of the composite.Differential Scanning Calorimetric(DSC)analysis was then used to assess the thermal properties of the composites,suggesting that this could be due to the amorphous phase formation of the intermolecular hydrogen bonds between PCL and nFA,resulting in the suppression of PCL crystallization.The results of mechanical characterization also showed that the addition of nFA up to 20 wt.%to the PCL increased the tensile and yield strength,as well as reducing the elongation at both yield and failure points and increasing the Young modulus.The best mechanical properties were obtained for the PCL/20nFA composite.Tensile strength and Young modulus were increased by 30%and 179%,respectively;meanwhile,elongation of PCL/20nFA was decreased by 70%,as compared to the naked PCL.These changes could be attributed to the better distribution of the nFA filler in the PCL matrix.According to the obtained results,PCL/20nFA could be regarded as a good composite in terms of the mechanical properties for the regeneration of the bone tissue.展开更多
文摘Non-equilibrium solidification structures of Cu55Ni45 and Cu55Ni43Co2 alloys were prepared by the molten glass purification cycle superheating method.The variation of the recalescence phenomenon with the degree of undercooling in the rapid solidification process was investigated using an infrared thermometer.The addition of the Co element affected the evolution of the recalescence phenomenon in Cu-Ni alloys.The images of the solid-liquid interface migration during the rapid solidification of supercooled melts were captured by using a high-speed camera.The solidification rate of Cu-Ni alloys,with the addition of Co elements,was explored.Finally,the grain refinement structure with low supercooling was characterised using electron backscatter diffraction(EBSD).The effect of Co on the microstructural evolution during nonequilibrium solidification of Cu-Ni alloys under conditions of small supercooling is investigated by comparing the microstructures of Cu55Ni45 and Cu55Ni43Co2 alloys.The experimental results show that the addition of a small amount of Co weakens the recalescence behaviour of the Cu55Ni45 alloy and significantly reduces the thermal strain in the rapid solidification phase.In the rapid solidification phase,the thermal strain is greatly reduced,and there is a significant increase in the characteristic undercooling degree.Furthermore,the addition of Co and the reduction of Cu not only result in a lower solidification rate of the alloy,but also contribute to the homogenisation of the grain size.
文摘The aim of the study was to investigate the effect of different surface treatment of titanium(Ti)on the adhesion test results for dental application.Ti substrates roughened by 400 to 1500-grit SiC polish papers and alumina blasting,alkali treated by 5 molar(M)NaOH and KOH solutions and heat treated at the temperature range of 400-800℃were used in this study.The treated samples were subjected to the adhesion test.According to the results of the adhesion test,the adhesive strength showed the highest value for the blasted titanium among all polished and blasted samples.The Ti samples heated at 650℃showed the highest adhesive strength among all heat-treated samples.Further,the adhesion test results indicated the higher adhesive strength of chemically treated samples treated by NaOH rather than that by KOH.The polished and heated Ti samples showed the highest adhesive strength among all samples.
文摘Engineered cardiac constructs(ECC)aid in the progression of regenerative medicine,disease modeling and targeted drug delivery to adjust and aim the release of remedial combination as well as decrease the side effects of drugs.In this research,polycaprolactone/gold nanoparticles(PCL/GNPs)three-dimensional(3D)composite scaffolds were manufactured by 3D printing using the fused deposition modeling(FDM)method and then coated with gelatin/spironolactone(GEL/SPL).Scanning electron microscopy(SEM)and Fourier transform-infrared spectroscopy(FTIR–ATR)were applied to characterize the samples.Furthermore,drug release,biodegradation,behavior of the myoblasts(H9C2)cell line,and cytotoxicity of the 3D scaffolds were evaluated.The microstructural observation of the scaffolds reported interconnected pores with 150–300µm in diameter.The 3D scaffolds were degraded significantly after 28 days of immersion in stimulated body fluid(SBF),with the maximum rate of GEL-coated 3D scaffolds.SPL release from cross-linked GEL coating demonstrated the excess of drug release over time,and according to the control release systems,the drug delivery systems(DDS)went into balance after the 14th day.In addition,cell culture study showed that with the addition of GNPs,the proliferation of(H9C2)was enhanced,and with GEL/SPL coating the cell attachment and viability were improved significantly.These findings suggested that PCL/GNPs 3D scaffolds coated with GEL/SPL can be an appropriate choice for myocardial tissue engineering.
文摘Graphene oxide has been used widely as a starting precursor for applications that cater to the needs of tunable graphene. However, the hydrophilic characteristic limits their application, especially in a hydrophobic condition. Herein, a novel non-covalent surface modification approach towards graphene oxide was conducted via a UV-induced photo-polymerization technique that involves two major routes; a UV-sensitive initiator embedded via pi-pi interactions on the graphene planar rings, and the polymerization of hydrophobic polymeric chains along the surface. The functionalized graphene oxide successfully achieved the desired hydrophobicity as it displayed the characteristic of being readily dissolved in organic solvent. Upon its addition into a polymeric solution and subjected to an electrospinning process,non-woven random nanofibers embedded with graphene oxide sheets were obtained. The prepared polymeric nanofibers were subjected to two-step thermal treatments that eventually converted the polymeric chains into a carbon-rich conductive structure. A unique morphology was observed upon the addition of the functionalized graphene oxide, whereby the sheets were embedded and intercalated within the carbon nanofibers and formed a continuous structure. This reinforcement effectively enhanced the electrochemical performance of the carbon nanofibers by recording a specific capacitance of up to 140.10 F/g at the current density of 1 A/g, which was approximately three folds more than that of pristine nanofibers.It also retained the capacitance up to 96.2% after 1000 vigorous charge/discharge cycles. This functionalization technique opens up a new pathway in tuning the solubility nature of graphene oxide towards the synthesis of a graphene oxide-reinforced polymeric structure.
文摘Arsenic is a natural tasteless and odourless element,existing in the earth's crust at average levels of between two and five thousands micrograms per liter (parts per million) . Arsenic is highly toxic to humans, who are exposed to it primarily from air,food and water. The occurrence of arsenic in groundwater is due to geological composition of soil. High concentrations of arsenic in water are the result of dissolution or desorption of ferric oxides and the oxidation of mineral arsenopyrites. Arsenic in drinking water has an important impact on the human health,especially in the less developed countries. Different methods exist to remove arsenic from aquatic media,and one of them is by adsorption. In this work,the adsorption of both As(III) and As(V) by means of novel microspheres has been investigated. In particular,TiO2 has been embedded into polymeric microspheres PES (PolyEtherSulphone) and PEEK-WC (PolyEtherEther-Ketone) . The main advantages of this encapsulation adsorption material are: no loss of adsorbents into the water stream,easy to be used and scaled-up.
文摘Crack growth modeling has always been one of the major challenges in fracture mechanics.Among all numerical methods,the extended finite element method(XFEM)has recently attracted much attention due to its ability to estimate the discontinuous deformation field.However,XFEM modeling does not directly lead to reliable results,and choosing a strategy of implementation is inevitable,especially in porous media.In this study,two prevalent XFEM strategies are evaluated:a)applying reduced Young’s modulus to pores and b)using different partitions to the model and enriching each part individually.We mention the advantages and limitations of each strategy via both analytical and experimental validations.Finally,the crack growth is modeled in a natural porous media(Fontainebleau sandstone).Our investigations proved that although both strategies can identically predict the stress distribution in the sample,the first strategy simulates only the initial crack propagation,while the second strategy could model multiple cracks growths.Both strategies are reliable and highly accurate in calculating the stress intensity factor,but the second strategy can compute a more reliable reaction force.Experimental tests showed that the second strategy is a more accurate strategy in predicting the preferred crack growth path and determining the maximum strength of the sample.
文摘In this study,nano-biocomposites of polycaprolactone(PCL)as the matrix and different amounts of nanofluorapatite(nFA)(0,10,20 and 30 wt.%)as the reinforcement were prepared for possible scaffold fabrication using the fused filament fabrication(FFF)3D printer.Field Emission Scanning Electron Microscopy(FE-SEM)and Energy Dispersive Spectroscopy(EDS)showed that nFA particles were well distributed in the PCL matrix.X-ray diffraction analysis(XRD)and Fourier Transform Infrared Spectroscopy(FTIR)depicted no chemical interaction between the elements of the composite.Differential Scanning Calorimetric(DSC)analysis was then used to assess the thermal properties of the composites,suggesting that this could be due to the amorphous phase formation of the intermolecular hydrogen bonds between PCL and nFA,resulting in the suppression of PCL crystallization.The results of mechanical characterization also showed that the addition of nFA up to 20 wt.%to the PCL increased the tensile and yield strength,as well as reducing the elongation at both yield and failure points and increasing the Young modulus.The best mechanical properties were obtained for the PCL/20nFA composite.Tensile strength and Young modulus were increased by 30%and 179%,respectively;meanwhile,elongation of PCL/20nFA was decreased by 70%,as compared to the naked PCL.These changes could be attributed to the better distribution of the nFA filler in the PCL matrix.According to the obtained results,PCL/20nFA could be regarded as a good composite in terms of the mechanical properties for the regeneration of the bone tissue.
