Investigation of rarely studied gravel layers found in the loess in Shandong Province,eastern China,reveals the fabric characteristics of two gravel layers(G1,G2)and the sedimentary characteristics of loess at the typ...Investigation of rarely studied gravel layers found in the loess in Shandong Province,eastern China,reveals the fabric characteristics of two gravel layers(G1,G2)and the sedimentary characteristics of loess at the typical and well-preserved Heiyu section(HY),where,to determine the paleoclimatic changes during Marine Isotope Stage 3a.Optically stimulated luminescence dates of the HY formation range from 0.26±0.02 ka to 39.00±2.00 ka.In addition,the ages of G1 and G2 were estimated using the Bayesian model to be 39.60-40.50 and 29.00-29.50 ka.G1 and G2 are mainly composed of fine and medium gravel,both of which were subangular to subrounded limestone,with gravel directions to NE and E.The average flow velocity,average depth,and flood peak flow of G1 are 1.10 m/s,0.49 m,and 37.04 m^(3)/s,respectively,calculated using the flow energy method,whereas those of G2 are 0.98 m/s,0.38 m,and 18.38 m^(3)/s,respectively.Analysis of climate proxy indices show that the sedimentary environment of the gravel and loess in HY might be a regional response to global change.展开更多
The paper addresses the decentralized optimal control and stabilization problems for interconnected systems subject to asymmetric information.Compared with previous work,a closed-loop optimal solution to the control p...The paper addresses the decentralized optimal control and stabilization problems for interconnected systems subject to asymmetric information.Compared with previous work,a closed-loop optimal solution to the control problem and sufficient and necessary conditions for the stabilization problem of the interconnected systems are given for the first time.The main challenge lies in three aspects:Firstly,the asymmetric information results in coupling between control and estimation and failure of the separation principle.Secondly,two extra unknown variables are generated by asymmetric information(different information filtration)when solving forward-backward stochastic difference equations.Thirdly,the existence of additive noise makes the study of mean-square boundedness an obstacle.The adopted technique is proving and assuming the linear form of controllers and establishing the equivalence between the two systems with and without additive noise.A dual-motor parallel drive system is presented to demonstrate the validity of the proposed algorithm.展开更多
As positioning sensors,edge computation power,and communication technologies continue to develop,a moving agent can now sense its surroundings and communicate with other agents.By receiving spatial information from bo...As positioning sensors,edge computation power,and communication technologies continue to develop,a moving agent can now sense its surroundings and communicate with other agents.By receiving spatial information from both its environment and other agents,an agent can use various methods and sensor types to localize itself.With its high flexibility and robustness,collaborative positioning has become a widely used method in both military and civilian applications.This paper introduces the basic fundamental concepts and applications of collaborative positioning,and reviews recent progress in the field based on camera,LiDAR(Light Detection and Ranging),wireless sensor,and their integration.The paper compares the current methods with respect to their sensor type,summarizes their main paradigms,and analyzes their evaluation experiments.Finally,the paper discusses the main challenges and open issues that require further research.展开更多
The occurrence characteristics of shale oil are of great significance to the movability of shale oil.In this study,the occurrence characteristics of oil in the shale matrix at Funing Formation shale in Subei Basin wer...The occurrence characteristics of shale oil are of great significance to the movability of shale oil.In this study,the occurrence characteristics of oil in the shale matrix at Funing Formation shale in Subei Basin were quantitatively evaluated by organic geochemistry and microscopic pore structure characterization experiments.The Multiple Isothermal Stages Pyrolysis(MIS)experiment results show that the content of total oil,adsorbed oil,and free oil in the shales are 3.15-11.25 mg/g,1.41-4.95 mg/g,and 1.74-6.51 mg/g,respectively.among which the silicon-rich shale has the best oil-bearing.The relative content of free oil shows an increasing trend in pores with pore diameters greater than 3 nm.When the relative content of free oil reaches 100%,the pore size of silicon-rich shale is about 200 nm,while that of calcium-rich shale,clay-rich shale,and siliceous mixed shale is about 10 nm.The occurrence law of adsorbed oil is opposite to that of free oil,which indicates that shale oil will occur in the pores and fractures in a free state in a more extensive pore size range(>200 nm).This study also enables us to further understand the occurrence characteristics of shale oil under the interaction of occurrence state and occurrence space.展开更多
Constructing a functional hybrid coating appears to be a promising strategy for addressing the poor corrosion resistance and insufficient endothelialization of Mg-based stents.Nevertheless,the steps for preparing comp...Constructing a functional hybrid coating appears to be a promising strategy for addressing the poor corrosion resistance and insufficient endothelialization of Mg-based stents.Nevertheless,the steps for preparing composite coatings are usually complicated and time-consuming.Herein,a novel composite coating,composed of bioactive magnesium thioctic acid(MTA)layer formed by deposition and corrosion-resistant magnesium hydroxide(Mg(OH)_(2))layer grown in situ,is simply fabricated on ZE21B alloys via one-step electrodeposition.Scanning electron microscopy(SEM)shows that the electrodeposited coating has a compact and uniform structure.And the high adhesion of the MTA/Mg(OH)_(2)hybrid coating is also confirmed by the micro-scratch test.Electrochemical test,scanning kelvin probe(SKP),and hydrogen evolution measurement indicate that the hybrid coating effectively reduces the degradation rate of Mg substrates.Haemocompatibility experiment and cell culture trial detect that the composite coating is of fine biocompatibility.Finally,the preparation mechanism of MTA/Mg(OH)_(2)hybrid coatings is discussed and proposed.This coating shows a great potential application for cardiovascular stents.展开更多
Coal pyrolysis is a fundamental reaction in the thermal processing and utilization of coal.Investigating the behavior and kinetics of coal pyrolysis is crucial for optimizing,designing,and developing a composite riser...Coal pyrolysis is a fundamental reaction in the thermal processing and utilization of coal.Investigating the behavior and kinetics of coal pyrolysis is crucial for optimizing,designing,and developing a composite riser for the staged pyrolysis gasification process of pulverized coal.In this study,the non-isothermal pyrolysis behavior and kinetics of coal were examined at different heating rates(30,50,100,300,500,700,and 900℃/min)using thermogravimetry(TG)coupled with Fourier-transform infrared spectroscopy.Analysis of the TG/derivative TG(TG/DTG)curves indicated that coal pyrolysis mainly occurred between 300℃ and 700℃.Higher heating rates led to more volatiles being released from the coal,and a higher temperature was required to achieve rapid pyrolysis.Kinetic analysis showed that both the model-free methods(Friedman,Flynn-Wall-Ozawa,and Kissinger-Akahira-Sunose)and the model-based method(Coats-Redfern)effectively describe the coal pyrolysis process.The change in the Ea values between the two kinetic models was consistent throughout the pyrolysis process,and the most probable mechanism was the F2 model(secondary chemical reaction).In addition,the heating rate did not change the overall reaction order of the pyrolysis process;however,a higher heating rate resulted in a decrease in the Ea value during the initial pyrolysis stage.展开更多
Mozambique's continental margin in East Africa was formed during the break-off stage of the east and west Gondwana lands. Studying the geological structure and division of continent-ocean boundary(COB) in Mozambiq...Mozambique's continental margin in East Africa was formed during the break-off stage of the east and west Gondwana lands. Studying the geological structure and division of continent-ocean boundary(COB) in Mozambique's continental margin is considered of great significance to rebuild Gondwana land and understand its movement mode. Along these lines, in this work, the initial Moho was fit using the known Moho depth from reflection seismic profiles, and a 3D multi-point constrained gravity inversion was carried out. Thus, highaccuracy Moho depth and crustal thickness in the study area were acquired. According to the crustal structure distribution based on the inversion results, the continental crust at the narrowest position of the Mozambique Channel was detected. According to the analysis of the crustal thickness, the Mozambique ridge is generally oceanic crust and the COB of the whole Mozambique continental margin is divided.展开更多
The fractured surrounding rocks of roadways pose major challenges to safe mining.Grouting has often been used to reinforce the surrounding rocks to mitigate the safety risks associated with fractured rocks.The aim of ...The fractured surrounding rocks of roadways pose major challenges to safe mining.Grouting has often been used to reinforce the surrounding rocks to mitigate the safety risks associated with fractured rocks.The aim of this study is to develop highly efficient composite ultrafine cement(CUC)grouts to reinforce the roadway in fractured surrounding rocks.The materials used are ultrafine cement(UC),ultrafine fly ash(UF),ultrafine slag(US),and additives(superplasticizer[SUP],aluminate ultrafine expansion agent[AUA],gypsum,and retarder).The fluidity,bleeding,shrinkage,setting time,chemical composition,microstructure,degree of hydration,and mechanical property of grouting materials were evaluated in this study.Also,a suitable and effective CUC grout mixture was used to reinforce the roadway in the fractured surrounding rock.The results have shown that the addition of UF and US reduces the plastic viscosity of CUC,and the best fluidity can be obtained by adding 40%UF and 10%US.Since UC and UF particles are small,the pozzolanic effect of UF promotes the hydration reaction,which is conductive to the stability of CUC grouts.In addition,fine particles of UC,UF,and US can effectively fill the pores,while the volumetric expansion of AUA and gypsum decreases the pores and thus affects the microstructure of the solidified grout.The compressive test results have shown that the addition of specific amounts of UF and US can ameliorate the mechanical properties of CUC grouts.Finally,the CUC22‐8 grout was used to reinforce the No.20322 belt roadway.The results of numerical simulation and field monitoring have indicated that grouting can efficaciously reinforce the surrounding rock of the roadway.In this research,high‐performance CUC grouts were developed for surrounding rock reinforcement of underground engineering by utilizing UC and some additives.展开更多
Cereal is an essential source of calories and protein for the global population.Accurately predicting cereal quality before harvest is highly desirable in order to optimise management for farmers,grading harvest and c...Cereal is an essential source of calories and protein for the global population.Accurately predicting cereal quality before harvest is highly desirable in order to optimise management for farmers,grading harvest and categorised storage for enterprises,future trading prices,and policy planning.The use of remote sensing data with extensive spatial coverage demonstrates some potential in predicting crop quality traits.Many studies have also proposed models and methods for predicting such traits based on multiplatform remote sensing data.In this paper,the key quality traits that are of interest to producers and consumers are introduced.The literature related to grain quality prediction was analyzed in detail,and a review was conducted on remote sensing platforms,commonly used methods,potential gaps,and future trends in crop quality prediction.This review recommends new research directions that go beyond the traditional methods and discusses grain quality retrieval and the associated challenges from the perspective of remote sensing data.展开更多
This paper considers the rational expectations model with multiplicative noise and input delay,where the system dynamics rely on the conditional expectations of future states.The main contribution is to obtain a suffi...This paper considers the rational expectations model with multiplicative noise and input delay,where the system dynamics rely on the conditional expectations of future states.The main contribution is to obtain a sufficient condition for the exact controllability of the rational expectations model.In particular,we derive a sufficient Gramian matrix condition and a rank condition for the delay-free case.The key is the solvability of the backward stochastic difference equations with input delay which is derived from the forward and backward stochastic system.展开更多
Faced with unprecedented changes in the world,China has chosen to continue expanding its opening-up and actively cooperate with other countries.Internationalization of education is one of the important directions for ...Faced with unprecedented changes in the world,China has chosen to continue expanding its opening-up and actively cooperate with other countries.Internationalization of education is one of the important directions for the future development of universities.Since the reform and opening-up,a series of Sino-foreign cooperative education policies have been successively released,forming a relatively systematic and complete policy system.Under the promotion of policies,Chinese universities actively engage in Sino-foreign cooperative education,with increasingly frequent educational exchanges and a clear trend towards internationalization.The scale of Sino-foreign cooperative education is also constantly expanding.It is worthy to explore how to draw on advanced teaching experience from overseas,continue to promote Sino-foreign cooperative education,and improve the quality of Sino-foreign cooperative education.展开更多
In the process of mining coalbed methane(CBM),an unsteady state often arises due to the rapid extraction,release and pressure relief of CBM.In this case,the effective stress of coal changes dynamically,affecting the s...In the process of mining coalbed methane(CBM),an unsteady state often arises due to the rapid extraction,release and pressure relief of CBM.In this case,the effective stress of coal changes dynamically,affecting the stability of the gassy coal seam.In this paper,gas release tests of gassy coal under conventional triaxial compression were performed,and the dynamic effective stress(DES)during gas release was obtained indirectly based on a constitutive equation and deformation of coal.The results show that the maximum increases in DES caused by the release of free gas and adsorbed gas under the stress of 1.1 MPa were 0.811 and 5.418 MPa,respectively,which seriously affected the stress state of the coal.During the gas release,the free gas pressure and the adsorbed gas volume were the parameters that directly affected the DES and showed a positive linear relationship with the DES with an intercept of zero.The DES of the coal sample increased exponentially with time,which was determined by the contents of free and adsorbed gas.Based on the experimental results and theoretical analysis,an effective stress model was obtained for loaded gassy coal during gas release.The results of verification indicated accuracy greater than 99%.展开更多
Gneisses with anatectic characteristics from the Liansan island in the Sulu UHPM(ultra-high pressure metamorphic)belt were studied for petrography,titanite U-Pb dating and mineral geochemistry.Three origins of garnets...Gneisses with anatectic characteristics from the Liansan island in the Sulu UHPM(ultra-high pressure metamorphic)belt were studied for petrography,titanite U-Pb dating and mineral geochemistry.Three origins of garnets are distinguished:metamorphic garnet,peritectic garnet and anatectic garnet,which are formed in the stages of peak metamorphism,retrograde anatexis and melt crystallization,respectively.The euhedral titanite has a high content of REE and high Th/U ratios,which is interpreted as indicating that it was newly-formed from an anatectic melt.The LA-ICP-MS titanite U-Pb dating yields 214-217 Ma ages for the titanite(melt)crystallization.The distribution of trace elements varies in response to the different host minerals at different stages.At the peak metamorphic stage,Y and HREE are mainly hosted by garnet,Ba and Rb by phengite,Sr,Nb,Ta,Pb,Th,U and LREE by allanite and Y,U and HREE by zircon.During partial melting,Y,Pb,Th,U and REE are released into the melt,which causes a dramatic decline of these element contents in the retrograde minerals.Finally,titanite absorbs most of the Nb,U,LREE and HREE from the melt.Therefore,the different stages of metamorphism have different mineral assemblages,which host different trace elements.展开更多
This wok proposed the extraction distillation coupled pervaporation(ED+PV) technology process using two different solvents to separate isopropanol(IPA) and diisopropyl ether(DIPE) from DIPE/IPA/H_(2)O ternary heteroge...This wok proposed the extraction distillation coupled pervaporation(ED+PV) technology process using two different solvents to separate isopropanol(IPA) and diisopropyl ether(DIPE) from DIPE/IPA/H_(2)O ternary heterogeneous azeotropes in industrial wastewater from the synthesis of isopropanol in this study.Based on strict design specifications, simulation and sequential iteration methods are used for process design and optimization. Compared to the ethylene glycol(EG)-EG+H_(2)O process and the 1,3-propanediol(PDO)-IPA+H_(2)O process, the total annual cost(TAC) of the EG-IPA+H_(2)O process decreased by 20.76% and 7.86%(PDO). Compared to the EG-EG+H_(2)O process, the TAC of the PDO-IPA+H_(2)O process reduced 14%, but the global warming potential(GWP) and human toxicity of the PDO-IPA+H_(2)O process increased 11.3% and 4.07% respectively. Compared to the PDO-IPA+H_(2)O process, the EG-IPA+H_(2)O process saves 7.86%(TAC), 9.78%(GWP) and 9.85%(human toxicity). The ED+PV process with EG is superior to PDO in factors of TAC, energy consumption, human toxicity and environment. The EG-IPA+H_(2)O process changed the separation order of the products of the multi-azeotropic system, reduced the cost and energy conservation of the system, and enhanced the environmental protection evaluation of the process, is the best process through life cycle assessment for analyzing the economy, energy conservation, environmental assessment and human toxicity, designing cleaner products, controlling waste discharge, and promoting the chemical purification industry. This work provides a new process design and optimized separation ideas, will have a good guiding significance for the research and application separation of multi-azeotropic mixture with mixed solvents in organic wastewater from the cleaner chemical production, has been up to standard wastewater discharge process, and realized the development goal of carbon peak and carbon neutrality in the sustainable development of chemical clean industry.展开更多
This study experimentally analyzes the nonlinear flow characteristics and channelization of fluid through rough-walled fractures during the shear process using a shear-flow-visualization apparatus.A series of fluid fl...This study experimentally analyzes the nonlinear flow characteristics and channelization of fluid through rough-walled fractures during the shear process using a shear-flow-visualization apparatus.A series of fluid flow and visualization tests is performed on four transparent fracture specimens with various shear displacements of 1 mm,3 mm,5 mm,7 mm and 10 mm under a normal stress of 0.5 MPa.Four granite fractures with different roughnesses are selected and quantified using variogram fractal dimensions.The obtained results show that the critical Reynolds number tends to increase with increasing shear displacement but decrease with increasing roughness of fracture surface.The flow paths are more tortuous at the beginning of shear because of the wide distribution of small contact spots.As the shear displacement continues to increase,preferential flow paths are more distinctly observed due to the decrease in the number of contact spots caused by shear dilation;yet the area of single contacts in-creases.Based on the experimental results,an empirical mathematical equation is proposed to quantify the critical Reynolds number using the contact area ratio and fractal dimension.展开更多
In this study,the effects of intermetallic compounds(Mg_(17)Al_(12)and Al_(8)Mn_(5))on the Mg-Al layered double hydroxide(LDH)formation mechanism and corrosion behavior of an in-situ LDH/Mg(OH)_(2)steam coatings on AZ...In this study,the effects of intermetallic compounds(Mg_(17)Al_(12)and Al_(8)Mn_(5))on the Mg-Al layered double hydroxide(LDH)formation mechanism and corrosion behavior of an in-situ LDH/Mg(OH)_(2)steam coatings on AZ80 Mg alloy were investigated.Citric acid(CA)was used to activate the alloy surface during the pretreatment process.The alloy was first pretreated with CA and then subjected to a hydrothermal process using ultrapure water to produce Mg-Al-LDH/Mg(OH)_(2)steam coating.The effect of different time of acid pretreatment on the activation of the intermetallic compounds was investigated.The microstructure and elemental composition of the obtained coatings were analyzed using FE-SEM,EDS,XRD and FT-IR.The corrosion resistance of the coated samples was evaluated using different techniques,i.e.,potentiodynamic polarization(PDP),electrochemical impedance spectrum(EIS)and hydrogen evolution test.The results indicated that the CA pretreatment significantly influenced the activity of the alloy surface by exposing the intermetallic compounds.The surface area fraction of Mg_(17)Al_(12)and Al_(8)Mn_(5)phases on the surface of the alloy was significantly higher after the CA pretreatment,and thus promoted the growth of the subsequent Mg-Al-LDH coatings.The CA pretreatment for 30 s resulted in a denser and thicker LDH coating.Increase in the CA pretreatment time significantly led to the improvement in corrosion resistance of the coated AZ80 alloy.The corrosion current density of the coated alloy was lower by three orders of magnitude as compared to the uncoated alloy.展开更多
The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear...The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear-formed fractures are prone to secondary instability,posing a severe threat to deep engineering.Although numerous studies regarding three-dimensional(3D)morphologies of fracture surfaces have been conducted,the understanding of shear-formed fractures under TM coupling conditions is limited.In this study,direct shear tests of intact granite under various TM coupling conditions were conducted,followed by 3D laser scanning tests of shear-formed fractures.Test results demonstrated that the peak shear strength of intact granite is positively correlated with the normal stress,whereas it is negatively correlated with the temperature.The internal friction angle and cohesion of intact granite significantly decrease with an increase in the temperature.The anisotropy,roughness value,and height of the asperities on the fracture surfaces are reduced as the normal stress increases,whereas their variation trends are the opposite as the temperature increases.The macroscopic failure mode of intact granite under TM coupling conditions is dominated by mixed tensileeshear and shear failures.As the normal stress increases,intragranular fractures are developed ranging from a local to a global distribution,and the macroscopic failure mode of intact granite changes from mixed tensileeshear to shear failure.Finally,3D morphological characteristics of the asperities on the shear-formed fracture surfaces were analyzed,and a quadrangular pyramid conceptual model representing these asperities was proposed and sufficiently verified.展开更多
This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(...This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.展开更多
Tonstein layers are found worldwide in the Permo-Carboniferous coal-bearing strata.This study investigates the geochronology,mineralogy,and geochemistry of four tonstein samples from the Permo-Carboniferous Benxi Form...Tonstein layers are found worldwide in the Permo-Carboniferous coal-bearing strata.This study investigates the geochronology,mineralogy,and geochemistry of four tonstein samples from the Permo-Carboniferous Benxi Formation,Ordos Basin,North China Craton(NCC).The typical features of the studied tonsteins include thin beds,lateral continuity,angular quartz grains,and euhedral zircons with similar U-Pb ages,indicating a significant pyroclastic origin.In addition,the tonstein samples have low TiO_(2)/Al_(2)O_(3)ratios(<0.02)and rare earth elements and yttrium(REY)concentrations with obvious negative Eu anomalies,indicating that the tonsteins have a felsic magma origin.Moreover,compared with the mean composition of clay shale,the studied tonsteins are characterized by high concentrations of the elements Nb and Ta,which may affect the concentration of the corresponding elements in surrounding coal seams.The zircon U-Pb ages of the tonsteins(293.9-298.8 Ma)provide a precise chronological framework on the Benxi Formation in the Ordos Basin,constraining the Gzhelian-Aselian stages.The tonsteins were probably sourced from arc volcanism along the western margin of the NCC during the early Permian,implying that the Alxa Terrane had not amalgamated with the NCC at that time.展开更多
Since 2008 a network of five sea-level monitoring stations was progressively installed in French Polynesia.The stations are autonomous and data,collected at a sampling rate of 1 or 2 min,are not only recorded locally,...Since 2008 a network of five sea-level monitoring stations was progressively installed in French Polynesia.The stations are autonomous and data,collected at a sampling rate of 1 or 2 min,are not only recorded locally,but also transferred in real time by a radio-link to the NOAA through the GOES satellite.The new ET34-ANA-V80 version of ETERNA,initially developed for Earth Tides analysis,is now able to analyze ocean tides records.Through a two-step validation scheme,we took advantage of the flexibility of this new version,operated in conjunction with the preprocessing facilities of the Tsoft software,to recover co rrected data series able to model sea-level variations after elimination of the ocean tides signal.We performed the tidal analysis of the tide gauge data with the highest possible selectivity(optimal wave grouping)and a maximum of additional terms(shallow water constituents).Our goal was to provide corrected data series and modelled ocean tides signal to compute tide-free sea-level variations as well as tidal prediction models with centimeter precision.We also present in this study the characteristics of the ocean tides in French Polynesia and preliminary results concerning the non-tidal variations of the sea level concerning the tide gauge setting.展开更多
基金the National Natural Science Foundation of China(Grant Nos.41472159,41172160,41371537).
文摘Investigation of rarely studied gravel layers found in the loess in Shandong Province,eastern China,reveals the fabric characteristics of two gravel layers(G1,G2)and the sedimentary characteristics of loess at the typical and well-preserved Heiyu section(HY),where,to determine the paleoclimatic changes during Marine Isotope Stage 3a.Optically stimulated luminescence dates of the HY formation range from 0.26±0.02 ka to 39.00±2.00 ka.In addition,the ages of G1 and G2 were estimated using the Bayesian model to be 39.60-40.50 and 29.00-29.50 ka.G1 and G2 are mainly composed of fine and medium gravel,both of which were subangular to subrounded limestone,with gravel directions to NE and E.The average flow velocity,average depth,and flood peak flow of G1 are 1.10 m/s,0.49 m,and 37.04 m^(3)/s,respectively,calculated using the flow energy method,whereas those of G2 are 0.98 m/s,0.38 m,and 18.38 m^(3)/s,respectively.Analysis of climate proxy indices show that the sedimentary environment of the gravel and loess in HY might be a regional response to global change.
基金supported by the National Natural Science Foundation of China(62273213,62073199,62103241)Natural Science Foundation of Shandong Province for Innovation and Development Joint Funds(ZR2022LZH001)+4 种基金Natural Science Foundation of Shandong Province(ZR2020MF095,ZR2021QF107)Taishan Scholarship Construction Engineeringthe Original Exploratory Program Project of National Natural Science Foundation of China(62250056)Major Basic Research of Natural Science Foundation of Shandong Province(ZR2021ZD14)High-level Talent Team Project of Qingdao West Coast New Area(RCTD-JC-2019-05)。
文摘The paper addresses the decentralized optimal control and stabilization problems for interconnected systems subject to asymmetric information.Compared with previous work,a closed-loop optimal solution to the control problem and sufficient and necessary conditions for the stabilization problem of the interconnected systems are given for the first time.The main challenge lies in three aspects:Firstly,the asymmetric information results in coupling between control and estimation and failure of the separation principle.Secondly,two extra unknown variables are generated by asymmetric information(different information filtration)when solving forward-backward stochastic difference equations.Thirdly,the existence of additive noise makes the study of mean-square boundedness an obstacle.The adopted technique is proving and assuming the linear form of controllers and establishing the equivalence between the two systems with and without additive noise.A dual-motor parallel drive system is presented to demonstrate the validity of the proposed algorithm.
基金National Natural Science Foundation of China(Grant No.62101138)Shandong Natural Science Foundation(Grant No.ZR2021QD148)+1 种基金Guangdong Natural Science Foundation(Grant No.2022A1515012573)Guangzhou Basic and Applied Basic Research Project(Grant No.202102020701)for providing funds for publishing this paper。
文摘As positioning sensors,edge computation power,and communication technologies continue to develop,a moving agent can now sense its surroundings and communicate with other agents.By receiving spatial information from both its environment and other agents,an agent can use various methods and sensor types to localize itself.With its high flexibility and robustness,collaborative positioning has become a widely used method in both military and civilian applications.This paper introduces the basic fundamental concepts and applications of collaborative positioning,and reviews recent progress in the field based on camera,LiDAR(Light Detection and Ranging),wireless sensor,and their integration.The paper compares the current methods with respect to their sensor type,summarizes their main paradigms,and analyzes their evaluation experiments.Finally,the paper discusses the main challenges and open issues that require further research.
基金This work was financially supported by the National Natural Science Foundation of China(41972123,41922015)the Natural Science Foundation of Shandong Province(ZR2020QD036).
文摘The occurrence characteristics of shale oil are of great significance to the movability of shale oil.In this study,the occurrence characteristics of oil in the shale matrix at Funing Formation shale in Subei Basin were quantitatively evaluated by organic geochemistry and microscopic pore structure characterization experiments.The Multiple Isothermal Stages Pyrolysis(MIS)experiment results show that the content of total oil,adsorbed oil,and free oil in the shales are 3.15-11.25 mg/g,1.41-4.95 mg/g,and 1.74-6.51 mg/g,respectively.among which the silicon-rich shale has the best oil-bearing.The relative content of free oil shows an increasing trend in pores with pore diameters greater than 3 nm.When the relative content of free oil reaches 100%,the pore size of silicon-rich shale is about 200 nm,while that of calcium-rich shale,clay-rich shale,and siliceous mixed shale is about 10 nm.The occurrence law of adsorbed oil is opposite to that of free oil,which indicates that shale oil will occur in the pores and fractures in a free state in a more extensive pore size range(>200 nm).This study also enables us to further understand the occurrence characteristics of shale oil under the interaction of occurrence state and occurrence space.
基金the National Key Research and Development Program of China(2018YFC1106703)the National Natural Science Foundation of China(No.U1804251)。
文摘Constructing a functional hybrid coating appears to be a promising strategy for addressing the poor corrosion resistance and insufficient endothelialization of Mg-based stents.Nevertheless,the steps for preparing composite coatings are usually complicated and time-consuming.Herein,a novel composite coating,composed of bioactive magnesium thioctic acid(MTA)layer formed by deposition and corrosion-resistant magnesium hydroxide(Mg(OH)_(2))layer grown in situ,is simply fabricated on ZE21B alloys via one-step electrodeposition.Scanning electron microscopy(SEM)shows that the electrodeposited coating has a compact and uniform structure.And the high adhesion of the MTA/Mg(OH)_(2)hybrid coating is also confirmed by the micro-scratch test.Electrochemical test,scanning kelvin probe(SKP),and hydrogen evolution measurement indicate that the hybrid coating effectively reduces the degradation rate of Mg substrates.Haemocompatibility experiment and cell culture trial detect that the composite coating is of fine biocompatibility.Finally,the preparation mechanism of MTA/Mg(OH)_(2)hybrid coatings is discussed and proposed.This coating shows a great potential application for cardiovascular stents.
基金the financial support from the National Natural Science Foundation of China(Grant No.21576293 and 21576294)。
文摘Coal pyrolysis is a fundamental reaction in the thermal processing and utilization of coal.Investigating the behavior and kinetics of coal pyrolysis is crucial for optimizing,designing,and developing a composite riser for the staged pyrolysis gasification process of pulverized coal.In this study,the non-isothermal pyrolysis behavior and kinetics of coal were examined at different heating rates(30,50,100,300,500,700,and 900℃/min)using thermogravimetry(TG)coupled with Fourier-transform infrared spectroscopy.Analysis of the TG/derivative TG(TG/DTG)curves indicated that coal pyrolysis mainly occurred between 300℃ and 700℃.Higher heating rates led to more volatiles being released from the coal,and a higher temperature was required to achieve rapid pyrolysis.Kinetic analysis showed that both the model-free methods(Friedman,Flynn-Wall-Ozawa,and Kissinger-Akahira-Sunose)and the model-based method(Coats-Redfern)effectively describe the coal pyrolysis process.The change in the Ea values between the two kinetic models was consistent throughout the pyrolysis process,and the most probable mechanism was the F2 model(secondary chemical reaction).In addition,the heating rate did not change the overall reaction order of the pyrolysis process;however,a higher heating rate resulted in a decrease in the Ea value during the initial pyrolysis stage.
基金The National Natural Science Foundation of China under contract No. 42076078China–Mozambique Joint Cruise under contract No. GASI-01-DLJHJ-CM。
文摘Mozambique's continental margin in East Africa was formed during the break-off stage of the east and west Gondwana lands. Studying the geological structure and division of continent-ocean boundary(COB) in Mozambique's continental margin is considered of great significance to rebuild Gondwana land and understand its movement mode. Along these lines, in this work, the initial Moho was fit using the known Moho depth from reflection seismic profiles, and a 3D multi-point constrained gravity inversion was carried out. Thus, highaccuracy Moho depth and crustal thickness in the study area were acquired. According to the crustal structure distribution based on the inversion results, the continental crust at the narrowest position of the Mozambique Channel was detected. According to the analysis of the crustal thickness, the Mozambique ridge is generally oceanic crust and the COB of the whole Mozambique continental margin is divided.
基金supported by the National Natural Science Foundation of China(NSFC)(grant No.52074169,No.51704280)the China Postdoctoral Science Foundation(No.2023M732109)the Opening Foundation of Shandong Key Laboratory of Civil Engineering Disaster Prevention and Mitigation(No.CDPM2021FK02).
文摘The fractured surrounding rocks of roadways pose major challenges to safe mining.Grouting has often been used to reinforce the surrounding rocks to mitigate the safety risks associated with fractured rocks.The aim of this study is to develop highly efficient composite ultrafine cement(CUC)grouts to reinforce the roadway in fractured surrounding rocks.The materials used are ultrafine cement(UC),ultrafine fly ash(UF),ultrafine slag(US),and additives(superplasticizer[SUP],aluminate ultrafine expansion agent[AUA],gypsum,and retarder).The fluidity,bleeding,shrinkage,setting time,chemical composition,microstructure,degree of hydration,and mechanical property of grouting materials were evaluated in this study.Also,a suitable and effective CUC grout mixture was used to reinforce the roadway in the fractured surrounding rock.The results have shown that the addition of UF and US reduces the plastic viscosity of CUC,and the best fluidity can be obtained by adding 40%UF and 10%US.Since UC and UF particles are small,the pozzolanic effect of UF promotes the hydration reaction,which is conductive to the stability of CUC grouts.In addition,fine particles of UC,UF,and US can effectively fill the pores,while the volumetric expansion of AUA and gypsum decreases the pores and thus affects the microstructure of the solidified grout.The compressive test results have shown that the addition of specific amounts of UF and US can ameliorate the mechanical properties of CUC grouts.Finally,the CUC22‐8 grout was used to reinforce the No.20322 belt roadway.The results of numerical simulation and field monitoring have indicated that grouting can efficaciously reinforce the surrounding rock of the roadway.In this research,high‐performance CUC grouts were developed for surrounding rock reinforcement of underground engineering by utilizing UC and some additives.
基金This study was supported by the National Natural Science Foundation of China(42271396)the Natural Science Foundation of Shandong Province(ZR2022MD017)+1 种基金the Key R&D Project of Hebei Province(22326406D)The European Space Agency(ESA)and Ministry of Science and Technology of China(MOST)Dragon(57457).
文摘Cereal is an essential source of calories and protein for the global population.Accurately predicting cereal quality before harvest is highly desirable in order to optimise management for farmers,grading harvest and categorised storage for enterprises,future trading prices,and policy planning.The use of remote sensing data with extensive spatial coverage demonstrates some potential in predicting crop quality traits.Many studies have also proposed models and methods for predicting such traits based on multiplatform remote sensing data.In this paper,the key quality traits that are of interest to producers and consumers are introduced.The literature related to grain quality prediction was analyzed in detail,and a review was conducted on remote sensing platforms,commonly used methods,potential gaps,and future trends in crop quality prediction.This review recommends new research directions that go beyond the traditional methods and discusses grain quality retrieval and the associated challenges from the perspective of remote sensing data.
基金supported by the National Natural Science Foundation of China under Grants 61821004,62250056,62350710214,U23A20325,62350055the Natural Science Foundation of Shandong Province,China(ZR2021ZD14,ZR2021JQ24)+2 种基金High-level Talent Team Project of Qingdao West Coast New Area,China(RCTD-JC-2019-05)Key Research and Development Program of Shandong Province,China(2020CXGC01208)Science and Technology Project of Qingdao West Coast New Area,China(2019-32,2020-20,2020-1-4).
文摘This paper considers the rational expectations model with multiplicative noise and input delay,where the system dynamics rely on the conditional expectations of future states.The main contribution is to obtain a sufficient condition for the exact controllability of the rational expectations model.In particular,we derive a sufficient Gramian matrix condition and a rank condition for the delay-free case.The key is the solvability of the backward stochastic difference equations with input delay which is derived from the forward and backward stochastic system.
基金This article is the research result of the Research and Practice Project on Education and Teaching Reform at Shandong University of Science and Technology Jinan Campus:"Research on the Blended Teaching Model of Online Courses and Full English Classroom Teaching"(JNJG202101),and 2021 Curriculum Special Construction Project(JNKCZX2021109)of Shandong University of Science and Technology Jinan Campus.
文摘Faced with unprecedented changes in the world,China has chosen to continue expanding its opening-up and actively cooperate with other countries.Internationalization of education is one of the important directions for the future development of universities.Since the reform and opening-up,a series of Sino-foreign cooperative education policies have been successively released,forming a relatively systematic and complete policy system.Under the promotion of policies,Chinese universities actively engage in Sino-foreign cooperative education,with increasingly frequent educational exchanges and a clear trend towards internationalization.The scale of Sino-foreign cooperative education is also constantly expanding.It is worthy to explore how to draw on advanced teaching experience from overseas,continue to promote Sino-foreign cooperative education,and improve the quality of Sino-foreign cooperative education.
基金This research was funded by the National Natural Science Foundation of China(No.52174081)the China Postdoctoral Science Foundation(No.2021M702001)+1 种基金the Postdoctoral Innovation Project of Shandong Province(No.202102002)the Natural Science Foundation of Shandong Province(No.2019GSF111036).
文摘In the process of mining coalbed methane(CBM),an unsteady state often arises due to the rapid extraction,release and pressure relief of CBM.In this case,the effective stress of coal changes dynamically,affecting the stability of the gassy coal seam.In this paper,gas release tests of gassy coal under conventional triaxial compression were performed,and the dynamic effective stress(DES)during gas release was obtained indirectly based on a constitutive equation and deformation of coal.The results show that the maximum increases in DES caused by the release of free gas and adsorbed gas under the stress of 1.1 MPa were 0.811 and 5.418 MPa,respectively,which seriously affected the stress state of the coal.During the gas release,the free gas pressure and the adsorbed gas volume were the parameters that directly affected the DES and showed a positive linear relationship with the DES with an intercept of zero.The DES of the coal sample increased exponentially with time,which was determined by the contents of free and adsorbed gas.Based on the experimental results and theoretical analysis,an effective stress model was obtained for loaded gassy coal during gas release.The results of verification indicated accuracy greater than 99%.
基金supported by funds from the National Natural Science Foundation of China(Grant Nos.42172067,41972064,U1906207)the SDUST Research Fund。
文摘Gneisses with anatectic characteristics from the Liansan island in the Sulu UHPM(ultra-high pressure metamorphic)belt were studied for petrography,titanite U-Pb dating and mineral geochemistry.Three origins of garnets are distinguished:metamorphic garnet,peritectic garnet and anatectic garnet,which are formed in the stages of peak metamorphism,retrograde anatexis and melt crystallization,respectively.The euhedral titanite has a high content of REE and high Th/U ratios,which is interpreted as indicating that it was newly-formed from an anatectic melt.The LA-ICP-MS titanite U-Pb dating yields 214-217 Ma ages for the titanite(melt)crystallization.The distribution of trace elements varies in response to the different host minerals at different stages.At the peak metamorphic stage,Y and HREE are mainly hosted by garnet,Ba and Rb by phengite,Sr,Nb,Ta,Pb,Th,U and LREE by allanite and Y,U and HREE by zircon.During partial melting,Y,Pb,Th,U and REE are released into the melt,which causes a dramatic decline of these element contents in the retrograde minerals.Finally,titanite absorbs most of the Nb,U,LREE and HREE from the melt.Therefore,the different stages of metamorphism have different mineral assemblages,which host different trace elements.
基金supported by the National Natural Science Foundation of China (21776145 and 21808117)。
文摘This wok proposed the extraction distillation coupled pervaporation(ED+PV) technology process using two different solvents to separate isopropanol(IPA) and diisopropyl ether(DIPE) from DIPE/IPA/H_(2)O ternary heterogeneous azeotropes in industrial wastewater from the synthesis of isopropanol in this study.Based on strict design specifications, simulation and sequential iteration methods are used for process design and optimization. Compared to the ethylene glycol(EG)-EG+H_(2)O process and the 1,3-propanediol(PDO)-IPA+H_(2)O process, the total annual cost(TAC) of the EG-IPA+H_(2)O process decreased by 20.76% and 7.86%(PDO). Compared to the EG-EG+H_(2)O process, the TAC of the PDO-IPA+H_(2)O process reduced 14%, but the global warming potential(GWP) and human toxicity of the PDO-IPA+H_(2)O process increased 11.3% and 4.07% respectively. Compared to the PDO-IPA+H_(2)O process, the EG-IPA+H_(2)O process saves 7.86%(TAC), 9.78%(GWP) and 9.85%(human toxicity). The ED+PV process with EG is superior to PDO in factors of TAC, energy consumption, human toxicity and environment. The EG-IPA+H_(2)O process changed the separation order of the products of the multi-azeotropic system, reduced the cost and energy conservation of the system, and enhanced the environmental protection evaluation of the process, is the best process through life cycle assessment for analyzing the economy, energy conservation, environmental assessment and human toxicity, designing cleaner products, controlling waste discharge, and promoting the chemical purification industry. This work provides a new process design and optimized separation ideas, will have a good guiding significance for the research and application separation of multi-azeotropic mixture with mixed solvents in organic wastewater from the cleaner chemical production, has been up to standard wastewater discharge process, and realized the development goal of carbon peak and carbon neutrality in the sustainable development of chemical clean industry.
基金This study has been partially funded by National Key Research and Development Program of China(Grant No.2020YFA0711800)the National Natural Science Foundation of China(Grant No.51979272)the Natural Science Foundation of Shandong Province,China(Grant No.ZR2021QE069).
文摘This study experimentally analyzes the nonlinear flow characteristics and channelization of fluid through rough-walled fractures during the shear process using a shear-flow-visualization apparatus.A series of fluid flow and visualization tests is performed on four transparent fracture specimens with various shear displacements of 1 mm,3 mm,5 mm,7 mm and 10 mm under a normal stress of 0.5 MPa.Four granite fractures with different roughnesses are selected and quantified using variogram fractal dimensions.The obtained results show that the critical Reynolds number tends to increase with increasing shear displacement but decrease with increasing roughness of fracture surface.The flow paths are more tortuous at the beginning of shear because of the wide distribution of small contact spots.As the shear displacement continues to increase,preferential flow paths are more distinctly observed due to the decrease in the number of contact spots caused by shear dilation;yet the area of single contacts in-creases.Based on the experimental results,an empirical mathematical equation is proposed to quantify the critical Reynolds number using the contact area ratio and fractal dimension.
基金This work was supported by the National Natural Science Foundation of China(Grant Nos.51601108 and 52071191)the Natural Science Foundation of Shandong Province(ZR2020ME011).
文摘In this study,the effects of intermetallic compounds(Mg_(17)Al_(12)and Al_(8)Mn_(5))on the Mg-Al layered double hydroxide(LDH)formation mechanism and corrosion behavior of an in-situ LDH/Mg(OH)_(2)steam coatings on AZ80 Mg alloy were investigated.Citric acid(CA)was used to activate the alloy surface during the pretreatment process.The alloy was first pretreated with CA and then subjected to a hydrothermal process using ultrapure water to produce Mg-Al-LDH/Mg(OH)_(2)steam coating.The effect of different time of acid pretreatment on the activation of the intermetallic compounds was investigated.The microstructure and elemental composition of the obtained coatings were analyzed using FE-SEM,EDS,XRD and FT-IR.The corrosion resistance of the coated samples was evaluated using different techniques,i.e.,potentiodynamic polarization(PDP),electrochemical impedance spectrum(EIS)and hydrogen evolution test.The results indicated that the CA pretreatment significantly influenced the activity of the alloy surface by exposing the intermetallic compounds.The surface area fraction of Mg_(17)Al_(12)and Al_(8)Mn_(5)phases on the surface of the alloy was significantly higher after the CA pretreatment,and thus promoted the growth of the subsequent Mg-Al-LDH coatings.The CA pretreatment for 30 s resulted in a denser and thicker LDH coating.Increase in the CA pretreatment time significantly led to the improvement in corrosion resistance of the coated AZ80 alloy.The corrosion current density of the coated alloy was lower by three orders of magnitude as compared to the uncoated alloy.
基金supported by the National Natural Science Foundation of China(Grant No.51974173)the Natural Science Foundation of Shandong Province,China(Grant No.ZR2020QD122).
文摘The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear-formed fractures are prone to secondary instability,posing a severe threat to deep engineering.Although numerous studies regarding three-dimensional(3D)morphologies of fracture surfaces have been conducted,the understanding of shear-formed fractures under TM coupling conditions is limited.In this study,direct shear tests of intact granite under various TM coupling conditions were conducted,followed by 3D laser scanning tests of shear-formed fractures.Test results demonstrated that the peak shear strength of intact granite is positively correlated with the normal stress,whereas it is negatively correlated with the temperature.The internal friction angle and cohesion of intact granite significantly decrease with an increase in the temperature.The anisotropy,roughness value,and height of the asperities on the fracture surfaces are reduced as the normal stress increases,whereas their variation trends are the opposite as the temperature increases.The macroscopic failure mode of intact granite under TM coupling conditions is dominated by mixed tensileeshear and shear failures.As the normal stress increases,intragranular fractures are developed ranging from a local to a global distribution,and the macroscopic failure mode of intact granite changes from mixed tensileeshear to shear failure.Finally,3D morphological characteristics of the asperities on the shear-formed fracture surfaces were analyzed,and a quadrangular pyramid conceptual model representing these asperities was proposed and sufficiently verified.
基金This research was supported by the Department of Mining Engineering at the University of Utah.In addition,the lead author wishes to acknowledge the financial support received from the Talent Introduction Project,part of the Elite Program of Shandong University of Science and Technology(No.0104060540171).
文摘This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.
基金supported by the National Natural Science Foundation of China(Grant Nos.41972170,42102127)Shandong Provincial Natural Science Foundation(Grant No.ZR2021QD087)+1 种基金Chinese Postdoctoral Science Foundation(Grant No.2021M702019)SDUST Research Fund(Grant No.2018TDJH101)。
文摘Tonstein layers are found worldwide in the Permo-Carboniferous coal-bearing strata.This study investigates the geochronology,mineralogy,and geochemistry of four tonstein samples from the Permo-Carboniferous Benxi Formation,Ordos Basin,North China Craton(NCC).The typical features of the studied tonsteins include thin beds,lateral continuity,angular quartz grains,and euhedral zircons with similar U-Pb ages,indicating a significant pyroclastic origin.In addition,the tonstein samples have low TiO_(2)/Al_(2)O_(3)ratios(<0.02)and rare earth elements and yttrium(REY)concentrations with obvious negative Eu anomalies,indicating that the tonsteins have a felsic magma origin.Moreover,compared with the mean composition of clay shale,the studied tonsteins are characterized by high concentrations of the elements Nb and Ta,which may affect the concentration of the corresponding elements in surrounding coal seams.The zircon U-Pb ages of the tonsteins(293.9-298.8 Ma)provide a precise chronological framework on the Benxi Formation in the Ordos Basin,constraining the Gzhelian-Aselian stages.The tonsteins were probably sourced from arc volcanism along the western margin of the NCC during the early Permian,implying that the Alxa Terrane had not amalgamated with the NCC at that time.
基金funding from the“Talent Introduction Scientific Research Start-Up Fund”of Shandong University of Science and Technology(Grant number 0104060510217)the“Open Fund of State Key Laboratory of Geodesy and Earth’s Dynamics”(Grant number SKLGED2021-3-5)。
文摘Since 2008 a network of five sea-level monitoring stations was progressively installed in French Polynesia.The stations are autonomous and data,collected at a sampling rate of 1 or 2 min,are not only recorded locally,but also transferred in real time by a radio-link to the NOAA through the GOES satellite.The new ET34-ANA-V80 version of ETERNA,initially developed for Earth Tides analysis,is now able to analyze ocean tides records.Through a two-step validation scheme,we took advantage of the flexibility of this new version,operated in conjunction with the preprocessing facilities of the Tsoft software,to recover co rrected data series able to model sea-level variations after elimination of the ocean tides signal.We performed the tidal analysis of the tide gauge data with the highest possible selectivity(optimal wave grouping)and a maximum of additional terms(shallow water constituents).Our goal was to provide corrected data series and modelled ocean tides signal to compute tide-free sea-level variations as well as tidal prediction models with centimeter precision.We also present in this study the characteristics of the ocean tides in French Polynesia and preliminary results concerning the non-tidal variations of the sea level concerning the tide gauge setting.
