The phenomenology involved in severe accidents in nuclear reactors is highly complex.Currently,integrated analysis programs used for severe accident analysis heavily rely on custom empirical parameters,which introduce...The phenomenology involved in severe accidents in nuclear reactors is highly complex.Currently,integrated analysis programs used for severe accident analysis heavily rely on custom empirical parameters,which introduce considerable uncertainty.Therefore,in recent years,the field of severe accidents has shifted its focus toward applying uncertainty analysis methods to quantify uncertainty in safety assessment programs,known as“best estimate plus uncertainty(BEPU).”This approach aids in enhancing our comprehension of these programs and their further development and improvement.This study concentrates on a third-generation pressurized water reactor equipped with advanced active and passive mitigation strategies.Through an Integrated Severe Accident Analysis Program(ISAA),numerical modeling and uncertainty analysis were conducted on severe accidents resulting from large break loss of coolant accidents.Seventeen uncertainty parameters of the ISAA program were meticulously screened.Using Wilks'formula,the developed uncertainty program code,SAUP,was employed to carry out Latin hypercube sampling,while ISAA was employed to execute batch calculations.Statistical analysis was then conducted on two figures of merit,namely hydrogen generation and the release of fission products within the pressure vessel.Uncertainty calculations revealed that hydrogen production and the fraction of fission product released exhibited a normal distribution,ranging from 182.784 to 330.664 kg and from 15.6 to 84.3%,respectively.The ratio of hydrogen production to reactor thermal power fell within the range of 0.0578–0.105.A sensitivity analysis was performed for uncertain input parameters,revealing significant correlations between the failure temperature of the cladding oxide layer,maximum melt flow rate,size of the particulate debris,and porosity of the debris with both hydrogen generation and the release of fission products.展开更多
Photothermal catalysis realizes the synergistic effect of solar energy and thermochemistry,which also has the potential to improve the reaction rate and optimize the selectivity.In this review,the research progress of...Photothermal catalysis realizes the synergistic effect of solar energy and thermochemistry,which also has the potential to improve the reaction rate and optimize the selectivity.In this review,the research progress of photothermal catalytic removal of volatile organic compounds(VOCs)by nano-catalysts in recent years is systematically reviewed.First,the fundamentals of photothermal catalysis and the fabrication of catalysts are described,and the design strategy of optimizing photothermal catalysis performance is proposed.Second,the performance for VOC degradation with photothermal catalysis is evaluated and compared for the batch and continuous systems.Particularly,the catalytic mechanism of VOC oxidation is systematically introduced based on experimental and theoretical study.Finally,the future limitations and challenges have been discussed,and potential research directions and priorities are highlighted.A broad view of recent photothermal catalyst fabrication,applications,challenges,and prospects can be systemically provided by this review.展开更多
The liquid slug length distribution is crucial for designing the downstream processing system with mul-tiphase pipeline. Experiments were conducted in a 133m long horizontal test loop. The measurements were per-formed...The liquid slug length distribution is crucial for designing the downstream processing system with mul-tiphase pipeline. Experiments were conducted in a 133m long horizontal test loop. The measurements were per-formed by conductivity probes to determine the liquid slug length distribution. The data covered both the slug and plug flow regimes. From experimental results, the mean liquid slug lengths were relatively insensitive to gas and liquid flow rates in the higher mixture velocity range. But in the lower mixture velocity range, the mean liquid slug length decreased and then increased with mixture velocity. It shows that the development length of slug flow was longer than x/D=1157. A slug tracking model was adapted to study the evolution of liquid slug length distribution in a horizontal pipeline. In the present model, the wake effect of elongated bubble and the pressure drop due to accel-eration are taken into account and random slug lengths are introduced at the entrance. The results of the model are compared with the measured slug length distributions of slug flow regime. It shows that the predicted mean and maximum slug lengths are in agreement with the experimental data at x/D=1157 and the form of the slug length distributions is also predicted well by the model.展开更多
The flow patterns and their transitions of oil-water two-phase flow in horizontal pipes were studied. The experiments were conducted in two kinds of horizontal tubes, made of plexiglas pipe and stainless steel pipe wi...The flow patterns and their transitions of oil-water two-phase flow in horizontal pipes were studied. The experiments were conducted in two kinds of horizontal tubes, made of plexiglas pipe and stainless steel pipe with 40mm ID respectively. No. 46 mechanical oil and tap water were used as working fluids. The superficial velocity ranges of oil and water were: 0.04-1.2m·s^-1 and 0.04-2.2 m·s^-1, respectively. The flow patterns were identified by visualization and by transient fluctuation signals of differential pressure drop. The flow patterns were defined according to the relative distribution ofoil and water phases in the pipes. Flow pattern maps were obtained for both pipelines. In addition, semi-theoretical transition criteria for the flow patterns were proposed, and the proposed transitional criteria are in reasonable agreement with available data in liquid-liquid systems.展开更多
Large vertical pipes are key structures connecting subsea wells to offshore platforms.However,existing studies mainly focus on small vertical pipes.In a vertical acrylic pipe with 80 mm inner diameter and 11 m height,...Large vertical pipes are key structures connecting subsea wells to offshore platforms.However,existing studies mainly focus on small vertical pipes.In a vertical acrylic pipe with 80 mm inner diameter and 11 m height,a high-speed camera was used to visually research the influences of pipe diameters,liquid properties and inlet effect on air-water co-flow characteristic.Different flow regime maps of vertical pipes(diameters are in the range of 50e189 mm)were compared and the critical gas velocity of the transition boundary from bubble to slug flow tended to increase with the increase of diameters at D≥80 mm.Drift-flux models were established in different flow regimes and liquid properties have a significant effect on drift coefficients of bubble flow and slug flow(void fraction a≤0.4).The influence of inlet turbulent effect on the gas-liquid interface distribution gradually weakened and disappeared from the pipe base to 85D,where the flow was fully developed.Slug frequency has a trend of increase first and then decrease with the gas Weber numbers increasing at low liquid superficial velocities(J_(L)≤0.31 m/s).And on the basis of this law,a new slug frequency correlation was proposed.It was found that there was an exponential relationship between the ratio of lengths of Taylor bubble to slug and the void fraction.展开更多
An in-depth analysis on the cooperativity of intermolecular interactions including hydrogen bonding andπ-π stacking in 1,3,5-triamino-2,4,6-trinitrobenzene(TATB) crystal was studied. Two quantities, cooperativity ra...An in-depth analysis on the cooperativity of intermolecular interactions including hydrogen bonding andπ-π stacking in 1,3,5-triamino-2,4,6-trinitrobenzene(TATB) crystal was studied. Two quantities, cooperativity rate and energy, were defined to evaluate the nature and strength of cooperativity in a series of clusters diverging from 1D to 3D prototypes. The origin and mechanism of the cooperative effect were settled to demonstrate that the nature of cooperativity is determined by whether the non-covalent interactions compete or promote with each other, which is manifested by the changing trend of electron transfer. There exists obvious cooperative effect in intra-layer and inter-layer structures as they own the equivalent non-covalent interactions, while anti-cooperative effect is also observed if two interactions correlate with each other. On the whole, in the process of crystal formation, the apparent cooperativity is the check and balance of the two effects, which is capable to support a global interaction among all of molecules and contribute to the stabilization of system. Based on the results, one may get a new insight to understand the relationship between non-covalent interactions and low impact sensitivity.展开更多
In this study,the open-source software MFIX-DEM simulations of a bubbling fluidized bed(BFB)are applied to assess nine drag models according to experimental and direct numerical simulation(DNS)results.The influence of...In this study,the open-source software MFIX-DEM simulations of a bubbling fluidized bed(BFB)are applied to assess nine drag models according to experimental and direct numerical simulation(DNS)results.The influence of superficial gas velocity on gas–solid flow is also examined.The results show that according to the distribution of time-averaged particle axial velocity in y direction,except for Wen–Yu and Tenneti–Garg–Subramaniam(TGS),other drag models are consistent with the experimental and DNS results.For the TGS drag model,the layer-by-layer movement of particles is observed,which indicates the particle velocity is not correctly predicted.The time domain and frequency domain analysis results of pressure drop of each drag model are similar.It is recommended to use the drag model derived from DNS or fine grid computational fluid dynamics–discrete element method(CFD-DEM)data first for CFD-DEM simulations.For the investigated BFB,the superficial gas velocity less than 0.9 m·s^(-1) should be adopted to obtain normal hydrodynamics.展开更多
Direct Numerical Simulations have been carried out to study the forced convection heat transfer of flow through fixed prolate particles for a variety of aspect ratios ar={5/4,5/3,5/1}with Reynolds number(Re)up to 100....Direct Numerical Simulations have been carried out to study the forced convection heat transfer of flow through fixed prolate particles for a variety of aspect ratios ar={5/4,5/3,5/1}with Reynolds number(Re)up to 100.Three variations of the solid volume fraction c={0.1,0.2,0.3}with four Hermans orientation factors S={−0.5,0,0.5,1}are studied.It has been found that changes in S cause prominent variations in the Nusselt number.In general,Nusselt number increases with the decrease of S.For all three aspect ratios,the Nusselt number remains a linear function of S at different c and Re.Therefore,it is concluded that,for heat transfer from prolate muti-particle system,the effects of orientations cannot be ignored.A new correlation for Nusselt number has been developed for arrays of prolate particles using the simulation data as a function of Re,c,S and ar.展开更多
As a primary type of clean energy,methane is also the second most important greenhouse gas after CO_(2)due to the high global warming potential.Large quantities of lean methane(0.1–1.0 vol%)are emitted into the atmos...As a primary type of clean energy,methane is also the second most important greenhouse gas after CO_(2)due to the high global warming potential.Large quantities of lean methane(0.1–1.0 vol%)are emitted into the atmosphere without any treatment during coal mine,oil,and natural gas production,thus leading to energy loss and greenhouse effect.In general,it is challenging to utilize lean methane due to its low concentration and flow instability,while catalytic combustion is a vital pathway to realize an efficient utilization of lean methane owing to the reduced emissions of polluting gases(e.g.,NOxand CO)during the reaction.In particular,to efficiently convert lean methane,it necessitates both the designs of highly active and stable heterogeneous catalysts that accelerate lean methane combustion at low temperatures and smart reactors that enable autothermal operation by optimizing heat management.In this review,we discuss the in-depth development,challenges,and prospects of catalytic lean methane combustion technology in various configurations,with particular emphasis on heat management from the point of view of material design combined with reactor configuration.The target is to describe a framework that can correlate the guiding principles among catalyst design,device innovation and system optimization,inspiring the development of groundbreaking combustion technology for the efficient utilization of lean methane.展开更多
Chokes are one of the most important components of downhole flow-control equipment.The particle erosion mathematical model,which considers particle-particle interaction,was established and used to simulate solid parti...Chokes are one of the most important components of downhole flow-control equipment.The particle erosion mathematical model,which considers particle-particle interaction,was established and used to simulate solid particle movement as well as particle erosion characteristics of the solid-liquid two-phase flow in a choke.The corresponding erosion reduction approach by setting ribs on the inner wall of the choke was advanced.This mathematical model includes three parts:the flow field simulation of the continuous carrier fluid by an Eulerian approach,the particle interaction simulation using the discrete particle hard sphere model by a Lagrangian approach and calculation of erosion rate using semi-empirical correlations.The results show that particles accumulated in a narrow region from inlet to outlet of the choke and the dominating factor affecting particle motion is the fluid drag force.As a result,the optimization of rib geometrical parameters indicates that good anti-erosion performance can be achieved by four ribs,each of them with a height(H) of 3 mm and a width(B) of 5 mm equaling the interval between ribs(L).展开更多
The experimental results of the deformation and breakup of a single drop immersed in a Newtonian liq-uid and subjected to a constant shear rate which generated by counter rotating Couette apparatus were presented in t...The experimental results of the deformation and breakup of a single drop immersed in a Newtonian liq-uid and subjected to a constant shear rate which generated by counter rotating Couette apparatus were presented in this paper. From experimental observations, the breakup occurred by three mechanisms, namely, necking, end pinching, and capillary instability. Quantitative results for the deformation and breakup of drop are presented. The maximum diameter and Sauter mean diameter of daughter drops and capillary thread radius are linearly related to the inverse shear rate and independent of the initial drop size, the dimensionless wavelength which is the wave-length divided by the thread width at breakup is independent of the shear rate and initial drop size, and the deforma-tion of threads follows a pseudo-affine deformation for Cai/Cac larger than 2.展开更多
Prediction of critical heat flux (CHF) in annular flow is important for the safety of once - through steam generator and the reactor core under accident conditions. The dryout in annular flow occurs at the point where...Prediction of critical heat flux (CHF) in annular flow is important for the safety of once - through steam generator and the reactor core under accident conditions. The dryout in annular flow occurs at the point where the film is depleted due to entrainment, deposition, and evaporation. The film thickness, film mass flow rate along axial distribution, and CHF are calculated in vertical upward round tube on the basis of a separated flow model of annular flow. The theoretical CHF values are higher than those derived from experimental data, with error being within 30%.展开更多
This article presents a theoretical investigation on the steady-state natural circulation characteristics of a new type of pressurized water reactor. Through numerically solving the one-dimensional steady-state single...This article presents a theoretical investigation on the steady-state natural circulation characteristics of a new type of pressurized water reactor. Through numerically solving the one-dimensional steady-state single-phase conservative equations for the primary circuit and the steady-state two-phase drift-flux conservative equations for the secondary side of the steam generator, the natural circulation characteristics were studied. On the basis of the pre- liminary calculation analysis, it was found that natural circulation mass flow rate was proportional to the exponential function of the power and that the value of the exponent is related to the operating conditions of the secondary side of the steam generator. The higher the outlet pressure of the secondary side of the steam generator, the higher the pri- mary natural circulation mass flow rate. The larger height difference between the core center and the steam generator center is favorable for the heat removal capacity of the natural circulation.展开更多
In this paper, response surface methodology(RSM) based on central composite design(CCD) is applied to obtain an optimization design for the fuel rod's diameter and distance cooled by turbulent Al_2O_3–water nanof...In this paper, response surface methodology(RSM) based on central composite design(CCD) is applied to obtain an optimization design for the fuel rod's diameter and distance cooled by turbulent Al_2O_3–water nanofluid for a typical pressurized water reactor(PWR). Fuel rods and nanofluid flow between them are simulated 3D using computational fluid dynamics(CFD) by ANSYS-FLUNET package software. The RNG k–ε model is used to simulate turbulent nanofluid flow between the rods. The effect of different nanoparticles concentration is also investigated on the Nusselt number from heat transfer efficiency view point. Results reveal that when distance parameter(a) is in the minimum level and diameter parameter(r) is in the maximum possible level, cooling the rods will be better due to higher Nusselt number in this situation. Also, using the different nanoparticles on the cooling process confirms that Al_2O_3 averagely 17% and TiO_2 10% improve the Nusselt numbers.展开更多
Because of the practical importance of two-phase instabilities, substantial efforts have been made to date to understand the physical phenomena governing such instabilities and to develop computational tools to model ...Because of the practical importance of two-phase instabilities, substantial efforts have been made to date to understand the physical phenomena governing such instabilities and to develop computational tools to model the dynamics. The purpose of this study is to present a numerical model for the analysis of flow-induced instabilities in forced-convection steam generator. The model is based on the assumption of homogeneous two-phase flow and ther- modynamic equilibrium of the phases. The thermal capacity of the heater wall has been included in the analysis. The model is used to analyze the flow instabilities in the steam generator and to study the effects of system pressure, mass flux, inlet temperature and inlet/outlet restriction, gap size, the ratio of do / di, and the ratio of qi / qo on the system be- havior.展开更多
The vapor-liquid self-adjusting controller is an innovative automatic regulating valve.In order to ensure adjusted objects run safely and economically,the controller automatically adjusts the liquid flux to keep liqui...The vapor-liquid self-adjusting controller is an innovative automatic regulating valve.In order to ensure adjusted objects run safely and economically,the controller automatically adjusts the liquid flux to keep liquid level at a required level according to physical properties of vapor-liquid two-phase fluid.The adjusting mechanics,the controller’s performance and influencing factors of its stability have been analyzed in this paper.The theoretical analysis and successful applications have demonstrated this controller can keep the liquid level steady with good performance.The actual application in industry has shown that the controller can satisfactorily meet the requirement of industrial production and has wide application areas.展开更多
Liquid film cooling as an advanced cooling technology is widely used in space vehicles.Stable operation of liquid film along the rocket combustion inner wall is crucial for thermal protection of rocket engines.The sta...Liquid film cooling as an advanced cooling technology is widely used in space vehicles.Stable operation of liquid film along the rocket combustion inner wall is crucial for thermal protection of rocket engines.The stability of liquid film is mainly determined by the characteristics of interfacial wave,which is rarely investigated right now.How to improve the stability of thin film has become a hot spot.In view of this,an advanced model based on the conventional Volume of Fluid(VOF)model is adopted to investigate the characteristics of interfacial wave in gas-liquid flow by using OpenFOAM,and the mechanism of formation and development of wave is revealed intuitively through numerical study.The effects from gas velocity,surface tension and dynamic viscosity of liquid(three factors)on the wave are studied respectively.It can be found that the gas velocity is critical to the formation and development of wave,and four modes of droplets generation are illustrated in this paper.Besides,a gas vortex near the gas-liquid interface can induce formation of wave easily,so changing the gas vortex state can regulate formation and development of wave.What’s more,the change rules of three factors influencing on the interfacial wave are obtained,and the surface tension has a negative effect on the formation and development of wave only when the surface tension coefficient is above the critical value,whereas the dynamic viscosity has a positive effect in this process.Lastly,the maximum height and maximum slope angle of wave will level off as the gas velocity increases.Meanwhile,the maximum slope angle of wave is usually no more than 38°,no matter what happens to the three factors.展开更多
基金This work was supported financially by the National Natural Science Foundation of China(No.12375176).
文摘The phenomenology involved in severe accidents in nuclear reactors is highly complex.Currently,integrated analysis programs used for severe accident analysis heavily rely on custom empirical parameters,which introduce considerable uncertainty.Therefore,in recent years,the field of severe accidents has shifted its focus toward applying uncertainty analysis methods to quantify uncertainty in safety assessment programs,known as“best estimate plus uncertainty(BEPU).”This approach aids in enhancing our comprehension of these programs and their further development and improvement.This study concentrates on a third-generation pressurized water reactor equipped with advanced active and passive mitigation strategies.Through an Integrated Severe Accident Analysis Program(ISAA),numerical modeling and uncertainty analysis were conducted on severe accidents resulting from large break loss of coolant accidents.Seventeen uncertainty parameters of the ISAA program were meticulously screened.Using Wilks'formula,the developed uncertainty program code,SAUP,was employed to carry out Latin hypercube sampling,while ISAA was employed to execute batch calculations.Statistical analysis was then conducted on two figures of merit,namely hydrogen generation and the release of fission products within the pressure vessel.Uncertainty calculations revealed that hydrogen production and the fraction of fission product released exhibited a normal distribution,ranging from 182.784 to 330.664 kg and from 15.6 to 84.3%,respectively.The ratio of hydrogen production to reactor thermal power fell within the range of 0.0578–0.105.A sensitivity analysis was performed for uncertain input parameters,revealing significant correlations between the failure temperature of the cladding oxide layer,maximum melt flow rate,size of the particulate debris,and porosity of the debris with both hydrogen generation and the release of fission products.
基金sponsored financially by the National Natural Science Foundation of China (No.21906104 and No.12175145)the Shanghai Rising-Star Program (21QA1406600).
文摘Photothermal catalysis realizes the synergistic effect of solar energy and thermochemistry,which also has the potential to improve the reaction rate and optimize the selectivity.In this review,the research progress of photothermal catalytic removal of volatile organic compounds(VOCs)by nano-catalysts in recent years is systematically reviewed.First,the fundamentals of photothermal catalysis and the fabrication of catalysts are described,and the design strategy of optimizing photothermal catalysis performance is proposed.Second,the performance for VOC degradation with photothermal catalysis is evaluated and compared for the batch and continuous systems.Particularly,the catalytic mechanism of VOC oxidation is systematically introduced based on experimental and theoretical study.Finally,the future limitations and challenges have been discussed,and potential research directions and priorities are highlighted.A broad view of recent photothermal catalyst fabrication,applications,challenges,and prospects can be systemically provided by this review.
基金Supported by the National Natural Science Foundation of China (No.50536020 and 50323001).
文摘The liquid slug length distribution is crucial for designing the downstream processing system with mul-tiphase pipeline. Experiments were conducted in a 133m long horizontal test loop. The measurements were per-formed by conductivity probes to determine the liquid slug length distribution. The data covered both the slug and plug flow regimes. From experimental results, the mean liquid slug lengths were relatively insensitive to gas and liquid flow rates in the higher mixture velocity range. But in the lower mixture velocity range, the mean liquid slug length decreased and then increased with mixture velocity. It shows that the development length of slug flow was longer than x/D=1157. A slug tracking model was adapted to study the evolution of liquid slug length distribution in a horizontal pipeline. In the present model, the wake effect of elongated bubble and the pressure drop due to accel-eration are taken into account and random slug lengths are introduced at the entrance. The results of the model are compared with the measured slug length distributions of slug flow regime. It shows that the predicted mean and maximum slug lengths are in agreement with the experimental data at x/D=1157 and the form of the slug length distributions is also predicted well by the model.
基金National Natural Science Foundation of China (No.59995462 and 10172069)
文摘The flow patterns and their transitions of oil-water two-phase flow in horizontal pipes were studied. The experiments were conducted in two kinds of horizontal tubes, made of plexiglas pipe and stainless steel pipe with 40mm ID respectively. No. 46 mechanical oil and tap water were used as working fluids. The superficial velocity ranges of oil and water were: 0.04-1.2m·s^-1 and 0.04-2.2 m·s^-1, respectively. The flow patterns were identified by visualization and by transient fluctuation signals of differential pressure drop. The flow patterns were defined according to the relative distribution ofoil and water phases in the pipes. Flow pattern maps were obtained for both pipelines. In addition, semi-theoretical transition criteria for the flow patterns were proposed, and the proposed transitional criteria are in reasonable agreement with available data in liquid-liquid systems.
基金supported by the National Natural Science Foundation of China(No.51888103,No.52076175).
文摘Large vertical pipes are key structures connecting subsea wells to offshore platforms.However,existing studies mainly focus on small vertical pipes.In a vertical acrylic pipe with 80 mm inner diameter and 11 m height,a high-speed camera was used to visually research the influences of pipe diameters,liquid properties and inlet effect on air-water co-flow characteristic.Different flow regime maps of vertical pipes(diameters are in the range of 50e189 mm)were compared and the critical gas velocity of the transition boundary from bubble to slug flow tended to increase with the increase of diameters at D≥80 mm.Drift-flux models were established in different flow regimes and liquid properties have a significant effect on drift coefficients of bubble flow and slug flow(void fraction a≤0.4).The influence of inlet turbulent effect on the gas-liquid interface distribution gradually weakened and disappeared from the pipe base to 85D,where the flow was fully developed.Slug frequency has a trend of increase first and then decrease with the gas Weber numbers increasing at low liquid superficial velocities(J_(L)≤0.31 m/s).And on the basis of this law,a new slug frequency correlation was proposed.It was found that there was an exponential relationship between the ratio of lengths of Taylor bubble to slug and the void fraction.
基金the support from the National Natural Science Foundation of China (No. 21875184)the Natural Science Foundation of Shaanxi Province (No. 2022JC-10)Youth Talent of Shaanxi “TeZhi” Program。
文摘An in-depth analysis on the cooperativity of intermolecular interactions including hydrogen bonding andπ-π stacking in 1,3,5-triamino-2,4,6-trinitrobenzene(TATB) crystal was studied. Two quantities, cooperativity rate and energy, were defined to evaluate the nature and strength of cooperativity in a series of clusters diverging from 1D to 3D prototypes. The origin and mechanism of the cooperative effect were settled to demonstrate that the nature of cooperativity is determined by whether the non-covalent interactions compete or promote with each other, which is manifested by the changing trend of electron transfer. There exists obvious cooperative effect in intra-layer and inter-layer structures as they own the equivalent non-covalent interactions, while anti-cooperative effect is also observed if two interactions correlate with each other. On the whole, in the process of crystal formation, the apparent cooperativity is the check and balance of the two effects, which is capable to support a global interaction among all of molecules and contribute to the stabilization of system. Based on the results, one may get a new insight to understand the relationship between non-covalent interactions and low impact sensitivity.
基金the China-CEEC Joint Higher Education Project(Cultivation Project)(CEEC2021001)Srdjan Beloševic,Aleksandar Milicevic and Ivan Tomanovic acknowledge the financial support by the Ministry of Science,Technological Development and Innovation of the Republic of Serbia(Contract Annex:451-03-47/2023-01/200017).
文摘In this study,the open-source software MFIX-DEM simulations of a bubbling fluidized bed(BFB)are applied to assess nine drag models according to experimental and direct numerical simulation(DNS)results.The influence of superficial gas velocity on gas–solid flow is also examined.The results show that according to the distribution of time-averaged particle axial velocity in y direction,except for Wen–Yu and Tenneti–Garg–Subramaniam(TGS),other drag models are consistent with the experimental and DNS results.For the TGS drag model,the layer-by-layer movement of particles is observed,which indicates the particle velocity is not correctly predicted.The time domain and frequency domain analysis results of pressure drop of each drag model are similar.It is recommended to use the drag model derived from DNS or fine grid computational fluid dynamics–discrete element method(CFD-DEM)data first for CFD-DEM simulations.For the investigated BFB,the superficial gas velocity less than 0.9 m·s^(-1) should be adopted to obtain normal hydrodynamics.
基金supported by the HPC Platform of Xi’an Jiaotong Universitysupport by the Natural Science Foundation of China (21978228,22078255)+2 种基金support by Shaanxi Creative Talents Promotion Plan-Technological Innovation Team (2019TD-039)the Fundamental Research Funds for the Central Universities (Creative Team Plan No.cxtd2017004 in Xi’an Jiaotong University)the China Scholarship Council (CSC,2017GXZ021009).
文摘Direct Numerical Simulations have been carried out to study the forced convection heat transfer of flow through fixed prolate particles for a variety of aspect ratios ar={5/4,5/3,5/1}with Reynolds number(Re)up to 100.Three variations of the solid volume fraction c={0.1,0.2,0.3}with four Hermans orientation factors S={−0.5,0,0.5,1}are studied.It has been found that changes in S cause prominent variations in the Nusselt number.In general,Nusselt number increases with the decrease of S.For all three aspect ratios,the Nusselt number remains a linear function of S at different c and Re.Therefore,it is concluded that,for heat transfer from prolate muti-particle system,the effects of orientations cannot be ignored.A new correlation for Nusselt number has been developed for arrays of prolate particles using the simulation data as a function of Re,c,S and ar.
基金financially supported by the National Natural Science Foundation of China(21922606,21876139)the National Natural Science Foundation of Shaanxi Province(2020JQ-919)+2 种基金the Shaanxi Natural Science Fundamental Shaanxi Coal Chemical Joint Fund(2019JLM-14)the Initial Scientific Research Fund for Special Zone’s Talents(XJ18T06)K.C.Wong Education Foundation。
文摘As a primary type of clean energy,methane is also the second most important greenhouse gas after CO_(2)due to the high global warming potential.Large quantities of lean methane(0.1–1.0 vol%)are emitted into the atmosphere without any treatment during coal mine,oil,and natural gas production,thus leading to energy loss and greenhouse effect.In general,it is challenging to utilize lean methane due to its low concentration and flow instability,while catalytic combustion is a vital pathway to realize an efficient utilization of lean methane owing to the reduced emissions of polluting gases(e.g.,NOxand CO)during the reaction.In particular,to efficiently convert lean methane,it necessitates both the designs of highly active and stable heterogeneous catalysts that accelerate lean methane combustion at low temperatures and smart reactors that enable autothermal operation by optimizing heat management.In this review,we discuss the in-depth development,challenges,and prospects of catalytic lean methane combustion technology in various configurations,with particular emphasis on heat management from the point of view of material design combined with reactor configuration.The target is to describe a framework that can correlate the guiding principles among catalyst design,device innovation and system optimization,inspiring the development of groundbreaking combustion technology for the efficient utilization of lean methane.
基金supported by the Fund of Innovation Research Group of National Natural Science Foundation of China (Grant NO.5052160450323001)Major Program of National Natural Science Foundation of China (Grant No.50536020)
文摘Chokes are one of the most important components of downhole flow-control equipment.The particle erosion mathematical model,which considers particle-particle interaction,was established and used to simulate solid particle movement as well as particle erosion characteristics of the solid-liquid two-phase flow in a choke.The corresponding erosion reduction approach by setting ribs on the inner wall of the choke was advanced.This mathematical model includes three parts:the flow field simulation of the continuous carrier fluid by an Eulerian approach,the particle interaction simulation using the discrete particle hard sphere model by a Lagrangian approach and calculation of erosion rate using semi-empirical correlations.The results show that particles accumulated in a narrow region from inlet to outlet of the choke and the dominating factor affecting particle motion is the fluid drag force.As a result,the optimization of rib geometrical parameters indicates that good anti-erosion performance can be achieved by four ribs,each of them with a height(H) of 3 mm and a width(B) of 5 mm equaling the interval between ribs(L).
基金Supported by the National Natural Science Foundation of China (No.50536020 and No.10172069).
文摘The experimental results of the deformation and breakup of a single drop immersed in a Newtonian liq-uid and subjected to a constant shear rate which generated by counter rotating Couette apparatus were presented in this paper. From experimental observations, the breakup occurred by three mechanisms, namely, necking, end pinching, and capillary instability. Quantitative results for the deformation and breakup of drop are presented. The maximum diameter and Sauter mean diameter of daughter drops and capillary thread radius are linearly related to the inverse shear rate and independent of the initial drop size, the dimensionless wavelength which is the wave-length divided by the thread width at breakup is independent of the shear rate and initial drop size, and the deforma-tion of threads follows a pseudo-affine deformation for Cai/Cac larger than 2.
文摘Prediction of critical heat flux (CHF) in annular flow is important for the safety of once - through steam generator and the reactor core under accident conditions. The dryout in annular flow occurs at the point where the film is depleted due to entrainment, deposition, and evaporation. The film thickness, film mass flow rate along axial distribution, and CHF are calculated in vertical upward round tube on the basis of a separated flow model of annular flow. The theoretical CHF values are higher than those derived from experimental data, with error being within 30%.
文摘This article presents a theoretical investigation on the steady-state natural circulation characteristics of a new type of pressurized water reactor. Through numerically solving the one-dimensional steady-state single-phase conservative equations for the primary circuit and the steady-state two-phase drift-flux conservative equations for the secondary side of the steam generator, the natural circulation characteristics were studied. On the basis of the pre- liminary calculation analysis, it was found that natural circulation mass flow rate was proportional to the exponential function of the power and that the value of the exponent is related to the operating conditions of the secondary side of the steam generator. The higher the outlet pressure of the secondary side of the steam generator, the higher the pri- mary natural circulation mass flow rate. The larger height difference between the core center and the steam generator center is favorable for the heat removal capacity of the natural circulation.
基金financial support of the National Natural Science Foundation of China (No. 51422604, 21276206)the National 863 Program of China (No. 2013AA050402)supported by the China Fundamental Research Funds for the Central Universities
文摘In this paper, response surface methodology(RSM) based on central composite design(CCD) is applied to obtain an optimization design for the fuel rod's diameter and distance cooled by turbulent Al_2O_3–water nanofluid for a typical pressurized water reactor(PWR). Fuel rods and nanofluid flow between them are simulated 3D using computational fluid dynamics(CFD) by ANSYS-FLUNET package software. The RNG k–ε model is used to simulate turbulent nanofluid flow between the rods. The effect of different nanoparticles concentration is also investigated on the Nusselt number from heat transfer efficiency view point. Results reveal that when distance parameter(a) is in the minimum level and diameter parameter(r) is in the maximum possible level, cooling the rods will be better due to higher Nusselt number in this situation. Also, using the different nanoparticles on the cooling process confirms that Al_2O_3 averagely 17% and TiO_2 10% improve the Nusselt numbers.
文摘Because of the practical importance of two-phase instabilities, substantial efforts have been made to date to understand the physical phenomena governing such instabilities and to develop computational tools to model the dynamics. The purpose of this study is to present a numerical model for the analysis of flow-induced instabilities in forced-convection steam generator. The model is based on the assumption of homogeneous two-phase flow and ther- modynamic equilibrium of the phases. The thermal capacity of the heater wall has been included in the analysis. The model is used to analyze the flow instabilities in the steam generator and to study the effects of system pressure, mass flux, inlet temperature and inlet/outlet restriction, gap size, the ratio of do / di, and the ratio of qi / qo on the system be- havior.
文摘The vapor-liquid self-adjusting controller is an innovative automatic regulating valve.In order to ensure adjusted objects run safely and economically,the controller automatically adjusts the liquid flux to keep liquid level at a required level according to physical properties of vapor-liquid two-phase fluid.The adjusting mechanics,the controller’s performance and influencing factors of its stability have been analyzed in this paper.The theoretical analysis and successful applications have demonstrated this controller can keep the liquid level steady with good performance.The actual application in industry has shown that the controller can satisfactorily meet the requirement of industrial production and has wide application areas.
文摘Liquid film cooling as an advanced cooling technology is widely used in space vehicles.Stable operation of liquid film along the rocket combustion inner wall is crucial for thermal protection of rocket engines.The stability of liquid film is mainly determined by the characteristics of interfacial wave,which is rarely investigated right now.How to improve the stability of thin film has become a hot spot.In view of this,an advanced model based on the conventional Volume of Fluid(VOF)model is adopted to investigate the characteristics of interfacial wave in gas-liquid flow by using OpenFOAM,and the mechanism of formation and development of wave is revealed intuitively through numerical study.The effects from gas velocity,surface tension and dynamic viscosity of liquid(three factors)on the wave are studied respectively.It can be found that the gas velocity is critical to the formation and development of wave,and four modes of droplets generation are illustrated in this paper.Besides,a gas vortex near the gas-liquid interface can induce formation of wave easily,so changing the gas vortex state can regulate formation and development of wave.What’s more,the change rules of three factors influencing on the interfacial wave are obtained,and the surface tension has a negative effect on the formation and development of wave only when the surface tension coefficient is above the critical value,whereas the dynamic viscosity has a positive effect in this process.Lastly,the maximum height and maximum slope angle of wave will level off as the gas velocity increases.Meanwhile,the maximum slope angle of wave is usually no more than 38°,no matter what happens to the three factors.
