This work reports an exceptional reversed yield strength asymmetry at room temperature for a rare-earth free magnesium alloy containing a mass of fine dispersed quasicrystal(I-phase)precipitates.Although exhibiting tr...This work reports an exceptional reversed yield strength asymmetry at room temperature for a rare-earth free magnesium alloy containing a mass of fine dispersed quasicrystal(I-phase)precipitates.Although exhibiting traditional basal texture,it owns an exceptional CYS/TYS as high as~1.17.Electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM)examinations indicate pyramidal and prismatic dislocations plus tensile twinning being activated after immediate yielding in compression while basal and non-basal dislocations in tension.I-phase particles transferred the concentrated stress by self-twinning to provide the driving force for tensile twin initiating in neighboring grains,thereby significantly increasing the critical resolved shear stress of tensile twinning to possibly the level of pyramidal slip,finally leading to the dominance of pyramidal slip plus tensile twinning in texture grains.This results in a higher contribution on yield strength by~55 MPa in compression than in tension,which reasonably agrees with the experimental yield strength difference(~38 MPa).It can be concluded that I-phase particles influence deformation modes in tension and in compression,finally result in reversed yield strength asymmetry.展开更多
The microstructure and precipitated phases of as-cast Mg-5Y-1.5Nd-x Zn-0.5Zr(x=0,2,4,6 wt.%)alloys were investigated by optical microscopy,scanning electron microscopy,energy-dispersive spectrometry and X-ray Diffract...The microstructure and precipitated phases of as-cast Mg-5Y-1.5Nd-x Zn-0.5Zr(x=0,2,4,6 wt.%)alloys were investigated by optical microscopy,scanning electron microscopy,energy-dispersive spectrometry and X-ray Diffraction.The exposure corrosion experiment of these magnesium alloys was tested in South China Sea and KEXUE vessel atmospheric environment.The corrosion characteristic and mechanism of magnesium alloys of Mg-5Y-1.5Nd-x Zn-0.5Zr(x=0,2,4,6 wt.%)alloys were analyzed by weight loss rate,corrosion depth,corrosion products and corrosion morphologies.The electrochemical corrosion tests were also measured in the natural seawater.The comprehensive results showed that Mg-5Y-1.5Nd-4Zn-0.5Zr magnesium alloy existed the best corrosion resistance whether in the marine atmospheric environment and natural seawater environment.That depended on the microstructure,type and distribution of precipitated phases in Mg-5Y-1.5Nd-4Zn-0.5Zr magnesium alloy.Sufficient quantity anodic precipitated phases in the microstructure of Mg-5Y-1.5Nd-4Zn-0.5Zr alloy played the key role in the corrosion resistance.展开更多
This project is set in one of the international frontier research fields in inorganic solid chemistry.At present, the research in organic/inorganic hybrid materials and nanocomposite optoelectronic functional material...This project is set in one of the international frontier research fields in inorganic solid chemistry.At present, the research in organic/inorganic hybrid materials and nanocomposite optoelectronic functional materials is under the spotlight in the realm of materials science; there remain quite a few difficulties hiding in the traditional synthesis methods.For instance, the reaction cycle is generally too long, rare earth luminescence components are covalently grafted onto the matrix network, and the stability and luminescence properties are quite poor.Hence, Prof.Zhang and his colleagues proposed a series of new methods and technologies through systematic studies to prepare organic/inorganic hybrid materials and nanocomposite optoelectronic functional materials, striving to solve those kinds of problems.Through many years' efforts, a scientific basis was established by the scientists for the design and performance of the materials, which is recognized of great practical significance.展开更多
A novel bifunctional task-specific ionic liquid(TSIL),i.e.[trialkylmethylammonium][sec-nonylphenoxy acetate]([A336] [CA-100]) was impregnated on intermediate polarized XAD-7 resin,and the prepared solvent impreganated...A novel bifunctional task-specific ionic liquid(TSIL),i.e.[trialkylmethylammonium][sec-nonylphenoxy acetate]([A336] [CA-100]) was impregnated on intermediate polarized XAD-7 resin,and the prepared solvent impreganated resin(SIR) was studied for rare earth(RE) separation.Adsorption ability of the SIR was indicated to be obviously higher than that prepared by [A336][NO3] because of the functional anion of [A336][CA-100].Adsorption kinetics,adsorption isotherm,separation and desorption of the SIR were also studied.展开更多
In spite of the tumor microenvironments responsive cancer therapy based on Fenton reaction(i.e.,chemodynamic therapy,CDT)has been attracted more attentions in recent years,the limited Fenton reaction efficiency is the...In spite of the tumor microenvironments responsive cancer therapy based on Fenton reaction(i.e.,chemodynamic therapy,CDT)has been attracted more attentions in recent years,the limited Fenton reaction efficiency is the important obstacle to further application in clinic.Herein,we synthesized novel FeO/MoS2 nanocomposites modified by bovine serum albumin(FeO/MoS2-BSA)with boosted Fenton reaction efficiency by the synergistic effect of co-catalyze and photothermal effect of MoS2 nanosheets triggered by the second near-infrared(NIR II)light.In the tumor microenvironments,the MoS2 nanosheets not only can accelerate the conversion of Fe3+ions to Fe2+ions by Mo4+ions on their surface to improve Fenton reaction efficiency,but also endow FeO/MoS2-BSA with good photothermal performances for photothermal-enhanced CDT and photothermal therapy(PTT).Consequently,benefiting from the synergetic-enhanced CDT/PTT,the tumors are eradicated completely in vivo.This work provides innovative synergistic strategy for constructing nanocomposites for highly efficient CDT.展开更多
The electrocatalytic activity of transition-metal-based compounds is closely related to the electronic configuration.However,optimizing the surface electron spin state of catalysts remains a challenge.Here,we develope...The electrocatalytic activity of transition-metal-based compounds is closely related to the electronic configuration.However,optimizing the surface electron spin state of catalysts remains a challenge.Here,we developed a spin-state and delocalized electron regulation method to optimize oxygen evolution reaction(OER)performance by in-situ growth of NiCo_(2)(OH)_(x) using Oswald ripening and coordinating etching process on MXene and plasma treatment.X-ray absorption spectroscopy,magnetic tests and electron paramagnetic resonance reveal that the coupling of NiCo_(2)(OH)_(x) and MXene can induce remarkable spin-state transition of Co^(3+)and transition metal ions electron delocalization,plasma treatment further optimizes the 3 d orbital structure and delocalized electron density.The unique Jahn-Teller phenomenon can be brought by the intermediate spin state(t2 _(g)^(5) e_(g)^(1))of Co^(3+),which benefits from the partial electron occupied egorbitals.This distinct electron configuration(t2_(g)^(5) e_(g)^(1))with unpaired electrons leads to orbital degeneracy,that the adsorption free energy of intermediate species and conductivity were further optimized.The optimized electrocatalyst exhibits excellent OER activity with an overpotential of 268 m V at 10 m A cm^(-2).DFT calculations show that plasma treatment can effectively regulate the d-band center of TMs to optimize the adsorption and improve the OER activity.This approach could guide the rational design and discovery of electrocatalysts with ideal electron configurations in the future.展开更多
The age-hardening behavior and precipitation evolution of an isothermal aged Mg-5Sm-0.6Zn-0.5Zr(wt.%) alloy have been systematically investigated by means of transmission electron microscopy(TEM) and atomic-resolution...The age-hardening behavior and precipitation evolution of an isothermal aged Mg-5Sm-0.6Zn-0.5Zr(wt.%) alloy have been systematically investigated by means of transmission electron microscopy(TEM) and atomic-resolution high-angle annular dark field scanning transmission electron microscopy(HAADF-STEM). The Vickers hardness of the present alloy increases first and then decreases with ageing time. The sample aged at 200 ℃ for 10 h exhibits a peak-hardness of 90.5 HV. In addition to the dominant β_(0)’ precipitate(orthorhombic,a = 0.642 nm, b = 3.336 nm and c = 0.521 nm) formed on {11-20}α planes, a certain number of γ’’ precipitate(hexagonal, a = 0.556 nm and c = 0.431 nm) formed on basal planes are also observed in the peak-aged alloy. Significantly, the basal γ’’ precipitate is more thermostable than prismatic β_(0)’ precipitate in the present alloy. β_(0)’ precipitates gradually coarsened and were even likely to transform into β_(1) phase(face centered cubic, a = 0.73 nm) with the increase of ageing time, which accordingly led to a gradual decrease in number density of precipitates and finally resulted in the decreased hardness and mechanical property in the over-aged alloys.展开更多
CO impurity-induced catalyst deactivation has long been one of the biggest challenges in proton-exchange membrane fuel cells,with the poisoning phenomenon mainly attributed to the overly strong adsorption on the catal...CO impurity-induced catalyst deactivation has long been one of the biggest challenges in proton-exchange membrane fuel cells,with the poisoning phenomenon mainly attributed to the overly strong adsorption on the catalytic site.Here,we present a mechanistic study that overturns this understanding by using Rh-based single-atom catalysis centers as model catalysts.We precisely modulated the chelation structure of the Rh catalyst by coordinating Rh with C or N atoms,and probed the reaction mechanism by surface-enhanced Raman spectroscopy.Direct spectroscopic evidence for intermediates indicates that the reactivity of adsorbed OH^(*),rather than the adsorption strength of CO^(*),dictates the CO electrocatalytic oxidation behavior.The RhN_(4)sites,which adsorb the OH^(*)intermediate more weakly than RhC4 sites,showed prominent CO oxidation activity that not only far exceeded the traditional Pt/C but also the RhC4 sites with similar CO adsorption strength.From this study,it is clear that a paradigm shift in future research should be considered to rationally design high-performance CO electro-oxidation reaction catalysts by sufficiently considering the water-related reaction intermediate during catalysis.展开更多
In order to lower the usage of expensive Cyanex 923 and increase the extraction capacity of the system of Cextrant 230,the synergistic extraction of thorium from chloride media by a mixture of Cextrant 230 and Cyanex ...In order to lower the usage of expensive Cyanex 923 and increase the extraction capacity of the system of Cextrant 230,the synergistic extraction of thorium from chloride media by a mixture of Cextrant 230 and Cyanex 923 was investigated.The maximum synergistic enhancement coefficient(R)of 1.53 is obtained at 1:1 molar ratio of Cextrant 230/Cyanex 923.The syne rgistic extracted species of Th^(4+)is determined as ThCl_(4)·2Cextrant 230·Cyanex 923.The synergistic extraction of Th^(4+)is an entropy-driven exothermic process.The loading capacity of 0.60 mol/L mixed extractant for thorium is about 17.10 g/L(calculated as ThO_(2)),and the loaded thorium in the organic phase can be effectively stripped by distilled water.For comparison,rare earth cations are barely extracted under the similar conditions,suggesting that the mixtures can be applied to separate thorium from rare earths.A cascade extraction process was developed based on the synergistic extraction system to separate thorium from the hydrochloric acid leaching of bastnaesite.The content of thorium in the leaching solution decreases obviously from 19.90 mg/L to1.4μg/L by 3 stages of extraction,which is superior to sole Cextrant 230 or Cyanex 923.The introduction of Cextrant 230 into the extraction system not only lowers the usage of Cyanex 923 but also enhances the selective extraction of thorium at low acidity,implying that the synergistic extraction system can selectively extract thorium more efficiently and economically than the sole systems.展开更多
The inexpensive and moisture-stable Lewis-acidic ionic liquids were prepared and applied for transesterification of soybean oil to biodiesel.The influences of molar ratio of methanol to soybean oil,reaction temperatur...The inexpensive and moisture-stable Lewis-acidic ionic liquids were prepared and applied for transesterification of soybean oil to biodiesel.The influences of molar ratio of methanol to soybean oil,reaction temperature and amount of ionic liquids were investigated.The transesterification of soybean oil to biodiesel catalyzed by choline chloride·xZnCl2 ionic liquids showed many advantages such as mild conditions and lower cost.On the other hand,the non-ideal yield and complicated separation between biodiesel and soybean oil were also investigated and analyzed.The improvement on the systems of choline chloride·xZnCl2 was proposed for further investigation.展开更多
Microstructure and tensile properties of a Mg-Sm-Zn-Zr alloy with various extrusion ratios(ERs)of 6.9,10.4 and 17.6 were systematically investigated.It was identified that,greater ER increased dynamic recrystallizatio...Microstructure and tensile properties of a Mg-Sm-Zn-Zr alloy with various extrusion ratios(ERs)of 6.9,10.4 and 17.6 were systematically investigated.It was identified that,greater ER increased dynamic recrystallization(DRX)fraction and coarsened DRX grains,which further suggests weakened basal fiber texture for the studied alloy.This is mainly due to the rising temperature from massive deformation heat when hot-extrusion.As a result,greater ER corresponds to a decreased strength but improved ductility.Finally,transmission electron microscopy(TEM)observations reveal that the dominant intermetallic phase,Mg_(3)Sm,is metastable,and it will transform into Mg_(41)Sm_(5)during extrusion with high-ER.This transformation leads to the accumulation of surplus Sm and Zn atoms,which induces the precipitation of Sm Zn_(3)phase at the surface of Mg_(41)Sm_(5)matrix.展开更多
Mg-9Al-xPr(x=0.4,0.8 and 1.2,mass fraction,%)magnesium alloys were prepared by high-pressure die-casting technique.The effects of Pr on the microstructures of die-cast Mg-9Al based alloy were investigated by XRD and S...Mg-9Al-xPr(x=0.4,0.8 and 1.2,mass fraction,%)magnesium alloys were prepared by high-pressure die-casting technique.The effects of Pr on the microstructures of die-cast Mg-9Al based alloy were investigated by XRD and SEM.Needle-like Al11Pr3 phase and polygon Al6Mn6Pr phase are found in the microstructure.With 0.4%Pr addition,fine needle-like Al11Pr3 phase and a small amount of polygon Al6Mn6Pr phase near the grain boundary are found in the microstructure.Increasing Pr addition to 0.8%, lots of coarse needle-like Al11Pr3 phase within grain and polygon Al6Mn6Pr phase on grain boundary are observed.Further increasing Pr addition,the size of needle-like Al11Pr3 phase decreases,while the size of polygon Al6Mn6Pr relatively increases.The mass fraction of Pr at around 0.8%is considered to be suitable to obtain the optimal mechanical properties.The optimal mechanical properties are mainly resulted from grain boundary strengthening obtained by precipitates and solid solution.展开更多
The influence of equal channel angular pressing on the tension-compression yield asymmetry of extruded Mg-5.3 Zn-0.6 Ca(weight percent)alloy has been investigated.The microstructure was obviously refined by the large ...The influence of equal channel angular pressing on the tension-compression yield asymmetry of extruded Mg-5.3 Zn-0.6 Ca(weight percent)alloy has been investigated.The microstructure was obviously refined by the large strain during the equal channel angular pressing,accompanied with very fine Ca_(2)Mg_(6)Zn_(3) phases with average diameter of 70 nm.The weak tension-compression yield asymmetry after equal channel angular pressing is mainly attributed to the reduced volume fraction of extension twinning during the compression,because the slope(k)of twinning in Hall-Petch relationship is higher than that of dislocation slip,and the twinning deformation is difficult to take place with decreasing grain size.The basal slip is more active in the alloy after equal channel angular pressing,due to the non-basal texture components,which hinders the twinning activation and reduces the yield asymmetry.Furthermore,the presence of fine precipitate restricts the twinning activation,which also contributes to the reduction of yield asymmetry.展开更多
Lightweight and mechanically strong natural silk fibers have been extensively investigated over the past decades.Inspired by this research,many artificial spinning techniques(wet spinning,dry spinning,electrospinning,...Lightweight and mechanically strong natural silk fibers have been extensively investigated over the past decades.Inspired by this research,many artificial spinning techniques(wet spinning,dry spinning,electrospinning,etc.)have been developed to fabricate robust protein fibers.As the traditional spinning methods provide poor control over the as-spun fibers,microfluidics has been integrated with these techniques to allow the fabrication of biological fibers in a well-designed manner,with simplicity and cost efficiency.The mechanical behavior of the developed fibers can be precisely modulated by controlling the type iop and size of microfluidic channel,flow rate,and shear force.This technique has been successfully used to manufacture a broad range of protein fibers,and can accelerate the production and application of protein fibers in various fields.This review outlines recent progress in the design and fabrication of protein-based fibers based on microfluidics.We first briefly discuss the natural spider silk-spinning process and the microfluidics spinning process.Next,the fabrication and mechanical properties of regenerated protein fibers via microfluidics are discussed,followed by a discussion of recombinant protein fibers.Other sourced protein fibers are also reviewed in detail.Finally,a brief outlook on the development of microfluidic technology for producing protein fibers is presented.展开更多
The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or...The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or Ce/La addition,the Ca-Ce/La cooperative microalloying results in an outstanding grain refinement,because the fine secondary phase particles effectively hinder the recrystallized grain growth.The coarse Ca2Mg6Zn3 phases promote the formation of Ca3(PO4)2 or hydroxyapatite particles during the immersion process and accelerate the dissolution of the corrosion product film,which destroys its integrity and results in the deterioration of anti-corrosive performance.The Ce/La elements can be dispersed within the conventional Mg7Zn3 phases,which reduce the internal galvanic corrosion between Mg matrix and the secondary phases,leading to an obvious improvement of corrosion resistance.Therefore,the Ca-Ce/La cooperative microalloying achieves a homogenous fine-grained microstructure and improves the protective ability of surface film,which will pave a new avenue for the design of biomedical Mg alloys in the coming future.展开更多
Manganese oxides are regarded as one of the most promising cathode materials in rechargeable aqueous Zn-ion batteries(ZIBs)because of the low price and high security.However,the practical application of Mn2O3 in ZIBs ...Manganese oxides are regarded as one of the most promising cathode materials in rechargeable aqueous Zn-ion batteries(ZIBs)because of the low price and high security.However,the practical application of Mn2O3 in ZIBs is still plagued by the low specific capacity and poor rate capability.Herein,highly crystalline Mn2O3 materials with interconnected mesostructures and controllable pore sizes are obtained via a ligand-assisted self-assembly process and used as high-performance electrode materials for reversible aqueous ZIBs.The coordination degree between Mn2+and citric acid ligand plays a crucial role in the formation of the mesostructure,and the pore sizes can be easily tuned from 3.2 to 7.3 nm.Ascribed to the unique feature of nanoporous architectures,excellent zinc-storage performance can be achieved in ZIBs during charge/discharge processes.The Mn2O3 electrode exhibits high reversible capacity(233 mAh g−1 at 0.3 A g−1),superior rate capability(162 mAh g−1 retains at 3.08 A g−1)and remarkable cycling durability over 3000 cycles at a high current rate of 3.08 A g−1.Moreover,the corresponding electrode reaction mechanism is studied in depth according to a series of analytical methods.These results suggest that rational design of the nanoporous architecture for electrode materials can effectively improve the battery performance.展开更多
Three-dimensional(3D) flowerlike hierarchical Zn2GeO4 and Mn2+-doped Zn2GeO4 microstructures have been prepared by a facile hydrothermal approach. X-Ray diffraction(XRD), field emission scanning electron micro-scopy(F...Three-dimensional(3D) flowerlike hierarchical Zn2GeO4 and Mn2+-doped Zn2GeO4 microstructures have been prepared by a facile hydrothermal approach. X-Ray diffraction(XRD), field emission scanning electron micro-scopy(FESEM), transmission electron microscopy(TEM) and photoluminescence(PL) spectrometry were employed to characterize the samples. Such flowerlike hierarchical Zn2GeO4 microstructures with an average diameter of 3―4 μm were found to be constructed by abundant single crystalline nanorods of about 90 nm in diameter. The luminescent properties of Zn2GeO4:xMn phosphors with different contents of Mn2+ as an activator were investigated. The Mn2+-doped samples showed green luminescence corresponding to the d-d transition of Mn2+ under the irradiation of UV light. The red shift(from 531 nm to 538 nm) in λem with increasing Mn2+ content was observed in the luminescent spectra, which should be attributed to a weak crystal field because of the substitution of Zn2+ by Mn2+ at a distorted tetrahedral lattice site.展开更多
The effect of Gd content on the microstructure and tensile properties of as-cast Mg-Sm-Zn-Zr alloy has been systematically investigated.In the Mg-3Sm-0.5Zn-0.5Zr alloy, the intermetallic compounds with multiple morpho...The effect of Gd content on the microstructure and tensile properties of as-cast Mg-Sm-Zn-Zr alloy has been systematically investigated.In the Mg-3Sm-0.5Zn-0.5Zr alloy, the intermetallic compounds with multiple morphologies are identified as Mg_(3)Sm phase. In addition to Mg_(3)RE phase, Mg_(5)RE phase originated from Gd addition is observed in Gd-modified alloys. It should be noted that the lattice parameters of all the observed intermetallic compounds are significantly reduced by Zn segregation. The segregation behavior of Zn in Mg_(3)Sm phase is inhibited to some extent by Gd addition due to the electronegativity difference between Sm/Gd and Zn elements. In addition, the increased Gd content effectively leads to much more accumulation of solute atoms in front of the liquid-solid interface during solidification, which can prominently promote nucleation in liquid region and then refine grains. The tensile yield stress of the present alloys is thus improved with increasing Gd addition. Finally, Gd-modified alloys exhibit significantly age-hardening effect, which can be mainly attributed to the high-volume fraction and high density nano-scale precipitates.展开更多
Ti45Zr30Ni25 and Ti45Zr30Ni25La alloys were prepared by melt-spinning, and the phase structure and electrochemical performances of the melt-spun alloys were investigated. The results showed that the Ti45Zr30Ni25 alloy...Ti45Zr30Ni25 and Ti45Zr30Ni25La alloys were prepared by melt-spinning, and the phase structure and electrochemical performances of the melt-spun alloys were investigated. The results showed that the Ti45Zr30Ni25 alloy was composed of the quasicrystalline phase, amorphous phase and Laves phase. The Ti45Zr30Ni25La alloy contained quasicrystalline and amorphous phases. The maximum discharge capacity was 111 mAh/g for the Ti45Zr30Ni25 alloy electrode, and 124 mAh/g for the Ti45Zr30Ni25La alloy electrode. The Ti45Zr30Ni25La alloy electrode exhibited a better high-rate dischargeability and cycling stability than the Ti45Zr30Ni25 alloy electrode. The improvement of electrochemical properties was mainly ascribed to the increase in the amorphous phase due to the addition of La.展开更多
The effect of CAl0.5W0.5(CAW) compound on the grain refinement of Mg-Al based alloys was investigated.The results show that CAW compound is an effective and active grain refiner.The grain size of binary Mg-Al alloys i...The effect of CAl0.5W0.5(CAW) compound on the grain refinement of Mg-Al based alloys was investigated.The results show that CAW compound is an effective and active grain refiner.The grain size of binary Mg-Al alloys is more than 500 μm,and it is changed to about 110 μm with a 1 wt.% CAW addition.The hardness increased with the decease of grain size monotonously.The mechanical properties are improved by the addition.The fine grain size is mainly ascribed to the dispersed Al2CO particles,which are very potent nucleating substrates for Mg-Al alloys.The nucleation cores formed by chemical reaction directly are well-distributed in the matrix.展开更多
基金financially supported by the Scientific and Technological Developing Scheme of Jilin Province under grants no.20220402012GHthe National Natural Science Foundation of China under grants no.U21A20323+3 种基金the Capital Construction Fund within the Budget of Jilin Province no.2021C038-1the Special high-tech industrialization project of science and technology cooperation between Jilin Province and Chinese Academy of Sciences under grant no.2021SYHZ0043 and 2022SYHZ0038the Major science and technology projects of Jilin Province and Changchun City under grant no.20210301024GXthe Project for Jilin provincial department of education under grant no.JJKH20220760KJ。
文摘This work reports an exceptional reversed yield strength asymmetry at room temperature for a rare-earth free magnesium alloy containing a mass of fine dispersed quasicrystal(I-phase)precipitates.Although exhibiting traditional basal texture,it owns an exceptional CYS/TYS as high as~1.17.Electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM)examinations indicate pyramidal and prismatic dislocations plus tensile twinning being activated after immediate yielding in compression while basal and non-basal dislocations in tension.I-phase particles transferred the concentrated stress by self-twinning to provide the driving force for tensile twin initiating in neighboring grains,thereby significantly increasing the critical resolved shear stress of tensile twinning to possibly the level of pyramidal slip,finally leading to the dominance of pyramidal slip plus tensile twinning in texture grains.This results in a higher contribution on yield strength by~55 MPa in compression than in tension,which reasonably agrees with the experimental yield strength difference(~38 MPa).It can be concluded that I-phase particles influence deformation modes in tension and in compression,finally result in reversed yield strength asymmetry.
基金National Natural Science Foundation of China for Exploring Key Scientific Instrument(No.41827805)the Open Funds of the State Key Laboratory of Rare Earth Resource Utilization(No.RERU2021017)Hainan Province Science and Technology Special Fund(ZDYF2021GXJS210)for providing support。
文摘The microstructure and precipitated phases of as-cast Mg-5Y-1.5Nd-x Zn-0.5Zr(x=0,2,4,6 wt.%)alloys were investigated by optical microscopy,scanning electron microscopy,energy-dispersive spectrometry and X-ray Diffraction.The exposure corrosion experiment of these magnesium alloys was tested in South China Sea and KEXUE vessel atmospheric environment.The corrosion characteristic and mechanism of magnesium alloys of Mg-5Y-1.5Nd-x Zn-0.5Zr(x=0,2,4,6 wt.%)alloys were analyzed by weight loss rate,corrosion depth,corrosion products and corrosion morphologies.The electrochemical corrosion tests were also measured in the natural seawater.The comprehensive results showed that Mg-5Y-1.5Nd-4Zn-0.5Zr magnesium alloy existed the best corrosion resistance whether in the marine atmospheric environment and natural seawater environment.That depended on the microstructure,type and distribution of precipitated phases in Mg-5Y-1.5Nd-4Zn-0.5Zr magnesium alloy.Sufficient quantity anodic precipitated phases in the microstructure of Mg-5Y-1.5Nd-4Zn-0.5Zr alloy played the key role in the corrosion resistance.
文摘This project is set in one of the international frontier research fields in inorganic solid chemistry.At present, the research in organic/inorganic hybrid materials and nanocomposite optoelectronic functional materials is under the spotlight in the realm of materials science; there remain quite a few difficulties hiding in the traditional synthesis methods.For instance, the reaction cycle is generally too long, rare earth luminescence components are covalently grafted onto the matrix network, and the stability and luminescence properties are quite poor.Hence, Prof.Zhang and his colleagues proposed a series of new methods and technologies through systematic studies to prepare organic/inorganic hybrid materials and nanocomposite optoelectronic functional materials, striving to solve those kinds of problems.Through many years' efforts, a scientific basis was established by the scientists for the design and performance of the materials, which is recognized of great practical significance.
基金supported by ‘Hundreds Talents Program’from Chinese Academy of Sciences, National Natural Science Foundation of China (50574080, 20901073)National Key Technology R&D Program of China (2006BAC02A10)Distinguished Young Scholar Foundation of Jilin Province (20060114)
文摘A novel bifunctional task-specific ionic liquid(TSIL),i.e.[trialkylmethylammonium][sec-nonylphenoxy acetate]([A336] [CA-100]) was impregnated on intermediate polarized XAD-7 resin,and the prepared solvent impreganated resin(SIR) was studied for rare earth(RE) separation.Adsorption ability of the SIR was indicated to be obviously higher than that prepared by [A336][NO3] because of the functional anion of [A336][CA-100].Adsorption kinetics,adsorption isotherm,separation and desorption of the SIR were also studied.
基金This work was supported by the financial aid from the National Natural Science Foundation of China(Grant Nos.51502284,21834007,21521092,21590794,and 21673220)the Program of Science and Technology Development Plan of Jilin Province of China(No.20170101186JC)+1 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB20030300)the Youth Innovation Promotion Association of Chinese Academy of Sciences(2019232).
文摘In spite of the tumor microenvironments responsive cancer therapy based on Fenton reaction(i.e.,chemodynamic therapy,CDT)has been attracted more attentions in recent years,the limited Fenton reaction efficiency is the important obstacle to further application in clinic.Herein,we synthesized novel FeO/MoS2 nanocomposites modified by bovine serum albumin(FeO/MoS2-BSA)with boosted Fenton reaction efficiency by the synergistic effect of co-catalyze and photothermal effect of MoS2 nanosheets triggered by the second near-infrared(NIR II)light.In the tumor microenvironments,the MoS2 nanosheets not only can accelerate the conversion of Fe3+ions to Fe2+ions by Mo4+ions on their surface to improve Fenton reaction efficiency,but also endow FeO/MoS2-BSA with good photothermal performances for photothermal-enhanced CDT and photothermal therapy(PTT).Consequently,benefiting from the synergetic-enhanced CDT/PTT,the tumors are eradicated completely in vivo.This work provides innovative synergistic strategy for constructing nanocomposites for highly efficient CDT.
基金supported by the National Natural Science Foundation of China(21801090,21831003 and 21621001)the Jilin Scientific and Technological Development Program(20200802003GH)+2 种基金the Scientific Research Project in the Education Department of Jilin Province(JJKH20211044KJ)the Project on Experimental Technique of Jilin University(409020720202)supported by Users with the Excellence Program of Hefei Science Center CAS(2020HSC-UE002)。
文摘The electrocatalytic activity of transition-metal-based compounds is closely related to the electronic configuration.However,optimizing the surface electron spin state of catalysts remains a challenge.Here,we developed a spin-state and delocalized electron regulation method to optimize oxygen evolution reaction(OER)performance by in-situ growth of NiCo_(2)(OH)_(x) using Oswald ripening and coordinating etching process on MXene and plasma treatment.X-ray absorption spectroscopy,magnetic tests and electron paramagnetic resonance reveal that the coupling of NiCo_(2)(OH)_(x) and MXene can induce remarkable spin-state transition of Co^(3+)and transition metal ions electron delocalization,plasma treatment further optimizes the 3 d orbital structure and delocalized electron density.The unique Jahn-Teller phenomenon can be brought by the intermediate spin state(t2 _(g)^(5) e_(g)^(1))of Co^(3+),which benefits from the partial electron occupied egorbitals.This distinct electron configuration(t2_(g)^(5) e_(g)^(1))with unpaired electrons leads to orbital degeneracy,that the adsorption free energy of intermediate species and conductivity were further optimized.The optimized electrocatalyst exhibits excellent OER activity with an overpotential of 268 m V at 10 m A cm^(-2).DFT calculations show that plasma treatment can effectively regulate the d-band center of TMs to optimize the adsorption and improve the OER activity.This approach could guide the rational design and discovery of electrocatalysts with ideal electron configurations in the future.
基金supported by the National Natural Science Foundation of China (Nos.52201120 and 52004100)the Open Funds of the State Key Laboratory of Rare Earth Resource Utilization (RERU2022013)the Fundamental Research Funds for the Central Universities,JLU。
文摘The age-hardening behavior and precipitation evolution of an isothermal aged Mg-5Sm-0.6Zn-0.5Zr(wt.%) alloy have been systematically investigated by means of transmission electron microscopy(TEM) and atomic-resolution high-angle annular dark field scanning transmission electron microscopy(HAADF-STEM). The Vickers hardness of the present alloy increases first and then decreases with ageing time. The sample aged at 200 ℃ for 10 h exhibits a peak-hardness of 90.5 HV. In addition to the dominant β_(0)’ precipitate(orthorhombic,a = 0.642 nm, b = 3.336 nm and c = 0.521 nm) formed on {11-20}α planes, a certain number of γ’’ precipitate(hexagonal, a = 0.556 nm and c = 0.431 nm) formed on basal planes are also observed in the peak-aged alloy. Significantly, the basal γ’’ precipitate is more thermostable than prismatic β_(0)’ precipitate in the present alloy. β_(0)’ precipitates gradually coarsened and were even likely to transform into β_(1) phase(face centered cubic, a = 0.73 nm) with the increase of ageing time, which accordingly led to a gradual decrease in number density of precipitates and finally resulted in the decreased hardness and mechanical property in the over-aged alloys.
基金Jilin Province Science and Technology Development Program,Grant/Award Numbers:20180101030JC,20190201270JC,20200201001JCNational Natural Science Foundation of China,Grant/Award Numbers:21633008,21673221,21875243,U1601211+1 种基金Research Innovation Fund,Grant/Award Number:DNL202010Special Funds for Guiding Local Scientific and Technological Development by the Central Government,Grant/Award Number:2020JH6/10500021。
文摘CO impurity-induced catalyst deactivation has long been one of the biggest challenges in proton-exchange membrane fuel cells,with the poisoning phenomenon mainly attributed to the overly strong adsorption on the catalytic site.Here,we present a mechanistic study that overturns this understanding by using Rh-based single-atom catalysis centers as model catalysts.We precisely modulated the chelation structure of the Rh catalyst by coordinating Rh with C or N atoms,and probed the reaction mechanism by surface-enhanced Raman spectroscopy.Direct spectroscopic evidence for intermediates indicates that the reactivity of adsorbed OH^(*),rather than the adsorption strength of CO^(*),dictates the CO electrocatalytic oxidation behavior.The RhN_(4)sites,which adsorb the OH^(*)intermediate more weakly than RhC4 sites,showed prominent CO oxidation activity that not only far exceeded the traditional Pt/C but also the RhC4 sites with similar CO adsorption strength.From this study,it is clear that a paradigm shift in future research should be considered to rationally design high-performance CO electro-oxidation reaction catalysts by sufficiently considering the water-related reaction intermediate during catalysis.
基金Project supported by the National Key Research and Development Project of China(2022YFC2905201)the Science and Technology Service Network Initiative Program of the Chinese Academy of Sciences(KFJ-STSQYZD-2021-18-001)+3 种基金the Research Projects of Ganjiang Innovation Academy,Chinese Academy of Sciences(E055C002)Jiangxi"Double Thous and Plan"(jxsq.2020101005)Jiangxi Province Natural Science Foundation(20212BAB213033)Ganzhou Science and Technology Program(2022CXRC9671)。
文摘In order to lower the usage of expensive Cyanex 923 and increase the extraction capacity of the system of Cextrant 230,the synergistic extraction of thorium from chloride media by a mixture of Cextrant 230 and Cyanex 923 was investigated.The maximum synergistic enhancement coefficient(R)of 1.53 is obtained at 1:1 molar ratio of Cextrant 230/Cyanex 923.The syne rgistic extracted species of Th^(4+)is determined as ThCl_(4)·2Cextrant 230·Cyanex 923.The synergistic extraction of Th^(4+)is an entropy-driven exothermic process.The loading capacity of 0.60 mol/L mixed extractant for thorium is about 17.10 g/L(calculated as ThO_(2)),and the loaded thorium in the organic phase can be effectively stripped by distilled water.For comparison,rare earth cations are barely extracted under the similar conditions,suggesting that the mixtures can be applied to separate thorium from rare earths.A cascade extraction process was developed based on the synergistic extraction system to separate thorium from the hydrochloric acid leaching of bastnaesite.The content of thorium in the leaching solution decreases obviously from 19.90 mg/L to1.4μg/L by 3 stages of extraction,which is superior to sole Cextrant 230 or Cyanex 923.The introduction of Cextrant 230 into the extraction system not only lowers the usage of Cyanex 923 but also enhances the selective extraction of thorium at low acidity,implying that the synergistic extraction system can selectively extract thorium more efficiently and economically than the sole systems.
基金Supported by the National High Technology Research and Development Program of China(2007AA06Z202)the National Key Technology Research and Development Program of China(2006BAC02A10)the Distinguished Young Scholars Foundation of Jilin Province(20060114)
文摘The inexpensive and moisture-stable Lewis-acidic ionic liquids were prepared and applied for transesterification of soybean oil to biodiesel.The influences of molar ratio of methanol to soybean oil,reaction temperature and amount of ionic liquids were investigated.The transesterification of soybean oil to biodiesel catalyzed by choline chloride·xZnCl2 ionic liquids showed many advantages such as mild conditions and lower cost.On the other hand,the non-ideal yield and complicated separation between biodiesel and soybean oil were also investigated and analyzed.The improvement on the systems of choline chloride·xZnCl2 was proposed for further investigation.
基金supported by the National Natural Science Foundation of China(No.52071093,51871069,51701200)Fundamental Research Funds for the Central Universities(3072020CF1009)+1 种基金the Open Funds of the State Key Laboratory of Rare Earth Resource Utilization(RERU2020012)Grant-in-Aid for JSPS Fellows from the Japan Society for the Promotion of Science。
文摘Microstructure and tensile properties of a Mg-Sm-Zn-Zr alloy with various extrusion ratios(ERs)of 6.9,10.4 and 17.6 were systematically investigated.It was identified that,greater ER increased dynamic recrystallization(DRX)fraction and coarsened DRX grains,which further suggests weakened basal fiber texture for the studied alloy.This is mainly due to the rising temperature from massive deformation heat when hot-extrusion.As a result,greater ER corresponds to a decreased strength but improved ductility.Finally,transmission electron microscopy(TEM)observations reveal that the dominant intermetallic phase,Mg_(3)Sm,is metastable,and it will transform into Mg_(41)Sm_(5)during extrusion with high-ER.This transformation leads to the accumulation of surplus Sm and Zn atoms,which induces the precipitation of Sm Zn_(3)phase at the surface of Mg_(41)Sm_(5)matrix.
基金Project(2006AA03Z520)supported by National High-tech Research and Development Program of ChinaProject(20080508)supported bythe Science and Technology Program of Jilin Province of China+2 种基金Project(2007094)supported by the Science and Technology Program of Education Department of Jilin Province of ChinaProject(2007101)supported by the Science&Technology Development ProgramProject supported by the Basic Research Program of Changchun University of Technology,China
文摘Mg-9Al-xPr(x=0.4,0.8 and 1.2,mass fraction,%)magnesium alloys were prepared by high-pressure die-casting technique.The effects of Pr on the microstructures of die-cast Mg-9Al based alloy were investigated by XRD and SEM.Needle-like Al11Pr3 phase and polygon Al6Mn6Pr phase are found in the microstructure.With 0.4%Pr addition,fine needle-like Al11Pr3 phase and a small amount of polygon Al6Mn6Pr phase near the grain boundary are found in the microstructure.Increasing Pr addition to 0.8%, lots of coarse needle-like Al11Pr3 phase within grain and polygon Al6Mn6Pr phase on grain boundary are observed.Further increasing Pr addition,the size of needle-like Al11Pr3 phase decreases,while the size of polygon Al6Mn6Pr relatively increases.The mass fraction of Pr at around 0.8%is considered to be suitable to obtain the optimal mechanical properties.The optimal mechanical properties are mainly resulted from grain boundary strengthening obtained by precipitates and solid solution.
基金The authors wish to highly acknowledge Prof.L.M.Wang of Changchun Institute of Applied Chemistry,Chinese Academy of Sciences,for his valuable suggestions and discussions.Thanks to the financial aid from the National Science&Technology Pillar Program(Grant No.2012BAE01B04)the National Natural Science Foundation of China(Grant No.51401200)the Natural Science Foundation of Jilin Province(Grant No.20140520099JH).
文摘The influence of equal channel angular pressing on the tension-compression yield asymmetry of extruded Mg-5.3 Zn-0.6 Ca(weight percent)alloy has been investigated.The microstructure was obviously refined by the large strain during the equal channel angular pressing,accompanied with very fine Ca_(2)Mg_(6)Zn_(3) phases with average diameter of 70 nm.The weak tension-compression yield asymmetry after equal channel angular pressing is mainly attributed to the reduced volume fraction of extension twinning during the compression,because the slope(k)of twinning in Hall-Petch relationship is higher than that of dislocation slip,and the twinning deformation is difficult to take place with decreasing grain size.The basal slip is more active in the alloy after equal channel angular pressing,due to the non-basal texture components,which hinders the twinning activation and reduces the yield asymmetry.Furthermore,the presence of fine precipitate restricts the twinning activation,which also contributes to the reduction of yield asymmetry.
文摘Lightweight and mechanically strong natural silk fibers have been extensively investigated over the past decades.Inspired by this research,many artificial spinning techniques(wet spinning,dry spinning,electrospinning,etc.)have been developed to fabricate robust protein fibers.As the traditional spinning methods provide poor control over the as-spun fibers,microfluidics has been integrated with these techniques to allow the fabrication of biological fibers in a well-designed manner,with simplicity and cost efficiency.The mechanical behavior of the developed fibers can be precisely modulated by controlling the type iop and size of microfluidic channel,flow rate,and shear force.This technique has been successfully used to manufacture a broad range of protein fibers,and can accelerate the production and application of protein fibers in various fields.This review outlines recent progress in the design and fabrication of protein-based fibers based on microfluidics.We first briefly discuss the natural spider silk-spinning process and the microfluidics spinning process.Next,the fabrication and mechanical properties of regenerated protein fibers via microfluidics are discussed,followed by a discussion of recombinant protein fibers.Other sourced protein fibers are also reviewed in detail.Finally,a brief outlook on the development of microfluidic technology for producing protein fibers is presented.
基金the National Natural Science Foundation(Grant nos.5177117&51671152 and 51874225)the Key Research and Development Program of Shanxi Province(Grant nos.2020KWZ-007 and 2018ZDXMGY-149)the Youth Innovation Team of Shanxi Universities and the Natural Science Foundation of Jilin Province(Grant no.20180414016GH).
文摘The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or Ce/La addition,the Ca-Ce/La cooperative microalloying results in an outstanding grain refinement,because the fine secondary phase particles effectively hinder the recrystallized grain growth.The coarse Ca2Mg6Zn3 phases promote the formation of Ca3(PO4)2 or hydroxyapatite particles during the immersion process and accelerate the dissolution of the corrosion product film,which destroys its integrity and results in the deterioration of anti-corrosive performance.The Ce/La elements can be dispersed within the conventional Mg7Zn3 phases,which reduce the internal galvanic corrosion between Mg matrix and the secondary phases,leading to an obvious improvement of corrosion resistance.Therefore,the Ca-Ce/La cooperative microalloying achieves a homogenous fine-grained microstructure and improves the protective ability of surface film,which will pave a new avenue for the design of biomedical Mg alloys in the coming future.
基金the Young Thousand Talented Program and the National Natural Science Foundation of China (21671073 and 21621001)the “111” Project of the Ministry of Education of China (B17020)Program for JLU Science and Technology Innovative Research Team
文摘Manganese oxides are regarded as one of the most promising cathode materials in rechargeable aqueous Zn-ion batteries(ZIBs)because of the low price and high security.However,the practical application of Mn2O3 in ZIBs is still plagued by the low specific capacity and poor rate capability.Herein,highly crystalline Mn2O3 materials with interconnected mesostructures and controllable pore sizes are obtained via a ligand-assisted self-assembly process and used as high-performance electrode materials for reversible aqueous ZIBs.The coordination degree between Mn2+and citric acid ligand plays a crucial role in the formation of the mesostructure,and the pore sizes can be easily tuned from 3.2 to 7.3 nm.Ascribed to the unique feature of nanoporous architectures,excellent zinc-storage performance can be achieved in ZIBs during charge/discharge processes.The Mn2O3 electrode exhibits high reversible capacity(233 mAh g−1 at 0.3 A g−1),superior rate capability(162 mAh g−1 retains at 3.08 A g−1)and remarkable cycling durability over 3000 cycles at a high current rate of 3.08 A g−1.Moreover,the corresponding electrode reaction mechanism is studied in depth according to a series of analytical methods.These results suggest that rational design of the nanoporous architecture for electrode materials can effectively improve the battery performance.
基金Supported by the National Natural Science Foundation of China(No.21073032)
文摘Three-dimensional(3D) flowerlike hierarchical Zn2GeO4 and Mn2+-doped Zn2GeO4 microstructures have been prepared by a facile hydrothermal approach. X-Ray diffraction(XRD), field emission scanning electron micro-scopy(FESEM), transmission electron microscopy(TEM) and photoluminescence(PL) spectrometry were employed to characterize the samples. Such flowerlike hierarchical Zn2GeO4 microstructures with an average diameter of 3―4 μm were found to be constructed by abundant single crystalline nanorods of about 90 nm in diameter. The luminescent properties of Zn2GeO4:xMn phosphors with different contents of Mn2+ as an activator were investigated. The Mn2+-doped samples showed green luminescence corresponding to the d-d transition of Mn2+ under the irradiation of UV light. The red shift(from 531 nm to 538 nm) in λem with increasing Mn2+ content was observed in the luminescent spectra, which should be attributed to a weak crystal field because of the substitution of Zn2+ by Mn2+ at a distorted tetrahedral lattice site.
基金JSPS KAKENHI for Scientific Research on Innovative Areas“Materials Science of a Mille-feuille Structure(Grant Numbers JP18H05475,JP18H05479)”the Open Funds of the State Key Laboratory of Rare Earth Resource Utilization(RERU2020012)+1 种基金“Nanotechnology Platform”of the MEXT,JapanGrant-in-Aid for JSPS Fellows(JP19F19775)。
文摘The effect of Gd content on the microstructure and tensile properties of as-cast Mg-Sm-Zn-Zr alloy has been systematically investigated.In the Mg-3Sm-0.5Zn-0.5Zr alloy, the intermetallic compounds with multiple morphologies are identified as Mg_(3)Sm phase. In addition to Mg_(3)RE phase, Mg_(5)RE phase originated from Gd addition is observed in Gd-modified alloys. It should be noted that the lattice parameters of all the observed intermetallic compounds are significantly reduced by Zn segregation. The segregation behavior of Zn in Mg_(3)Sm phase is inhibited to some extent by Gd addition due to the electronegativity difference between Sm/Gd and Zn elements. In addition, the increased Gd content effectively leads to much more accumulation of solute atoms in front of the liquid-solid interface during solidification, which can prominently promote nucleation in liquid region and then refine grains. The tensile yield stress of the present alloys is thus improved with increasing Gd addition. Finally, Gd-modified alloys exhibit significantly age-hardening effect, which can be mainly attributed to the high-volume fraction and high density nano-scale precipitates.
基金supported by the National Natural Science Foundation of China (No. 50571094)the Doctoral Foundation of Henan Polytechnic University, China (No. 648248)
文摘Ti45Zr30Ni25 and Ti45Zr30Ni25La alloys were prepared by melt-spinning, and the phase structure and electrochemical performances of the melt-spun alloys were investigated. The results showed that the Ti45Zr30Ni25 alloy was composed of the quasicrystalline phase, amorphous phase and Laves phase. The Ti45Zr30Ni25La alloy contained quasicrystalline and amorphous phases. The maximum discharge capacity was 111 mAh/g for the Ti45Zr30Ni25 alloy electrode, and 124 mAh/g for the Ti45Zr30Ni25La alloy electrode. The Ti45Zr30Ni25La alloy electrode exhibited a better high-rate dischargeability and cycling stability than the Ti45Zr30Ni25 alloy electrode. The improvement of electrochemical properties was mainly ascribed to the increase in the amorphous phase due to the addition of La.
基金supported by the Doctoral Foundation of Henan Polytechnic University (No.648248)the Science and Technology Program of Changchun (No.05GG54)
文摘The effect of CAl0.5W0.5(CAW) compound on the grain refinement of Mg-Al based alloys was investigated.The results show that CAW compound is an effective and active grain refiner.The grain size of binary Mg-Al alloys is more than 500 μm,and it is changed to about 110 μm with a 1 wt.% CAW addition.The hardness increased with the decease of grain size monotonously.The mechanical properties are improved by the addition.The fine grain size is mainly ascribed to the dispersed Al2CO particles,which are very potent nucleating substrates for Mg-Al alloys.The nucleation cores formed by chemical reaction directly are well-distributed in the matrix.
