This study proposed three types of Al—Hf reactive materials with particle size ratios(a),which were almost completely dense(porosity of<5.40%)owing to their preparation using hot-pressing technology.Microstructure...This study proposed three types of Al—Hf reactive materials with particle size ratios(a),which were almost completely dense(porosity of<5.40%)owing to their preparation using hot-pressing technology.Microstructure characteristics and phase composition were analyzed,and the influence of particle size ratios on dynamic mechanical behavior and damage mechanism were investigated.The prepared sample with a=0.1 exhibited continuous wrapping of the Hf phase by the Al phase.Hf—Hf contact(continuous Hf phase)within the sample gradually increased with increasing a,and a small amount of fine Hf appeared for the sample with a=1.The reactive materials exhibited clear strain-rate sensitivity,with flow stressσ0.05and failure strainεfincreasing approximately linearly with increasing strain rate.ε.It is found that the plastic deformation of the material increased with increasing strain rate.As a increased from 0.1 to 1,the flow stress gradually increased.Impact failure of the material was dominated by ductile fracture with a large Al phase plastic deformation band for lower a,while brittle fracture with crushed Hf particles occurred at higher a.Finally,a constitutive model based on BP neural network was proposed to describe the stress-strain relationships of the materials,with an average relative error of 2.22%.展开更多
This article investigates the characteristics of shock wave overpressure generated by multi-layer composite charge under different detonation modes.Combining dimensional analysis and the explosion mechanism of the cha...This article investigates the characteristics of shock wave overpressure generated by multi-layer composite charge under different detonation modes.Combining dimensional analysis and the explosion mechanism of the charge,a peak overpressure prediction model for the composite charge under singlepoint detonation and simultaneous detonation was established.The effects of the charge structure and initiation method on the overpressure field characteristics were investigated in AUTODYN simulation.The accuracy of the prediction model and the reliability of the numerical simulation method were subsequently verified in a series of static explosion experiments.The results reveal that the mass of the inner charge was the key factor determining the peak overpressure of the composite charge under single-point detonation.The peak overpressure in the radial direction improved apparently with an increase in the aspect ratio of the charge.The overpressure curves in the axial direction exhibited a multi-peak phenomenon,and the secondary peak overpressure even exceeded the primary peak at distances of 30D and 40D(where D is the charge diameter).The difference in peak overpressure among azimuth angles of 0-90°gradually decreased with an increase in the propagation distance of the shock wave.The coupled effect of the detonation energy of the inner and outer charge under simultaneous detonation improved the overpressure in both radial and axial directions.The difference in peak overpressure obtained from model prediction and experimental measurements was less than 16.4%.展开更多
The numerical simulation of a blast wave of a multilayer composite charge is investigated.A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is establishe...The numerical simulation of a blast wave of a multilayer composite charge is investigated.A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program.Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25-0.5 cm and 1-3 cm.The Euler--fluxcorrected transport solver is found to be suitable for the far-field calculation after mapping.A numerical simulation is conducted to study the formation,propagation,and interaction of the shock wave of the composite charge for different initiation modes.It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge.Additionally,it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation,and the peak pressure of the shock wave exponentially decays,fitting the calculation formula of the peak overpressure attenuation under different initiation modes,which is obtained and verified by experiment.The difference between numerical and experimental results is less than 10%,and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.展开更多
The influe nce of initiation modes on the explosive dispersion process of the multi-layer co mposite charge(MCC) was studied.Overpressure sensors and high-speed photography system were used to investigate the energy r...The influe nce of initiation modes on the explosive dispersion process of the multi-layer co mposite charge(MCC) was studied.Overpressure sensors and high-speed photography system were used to investigate the energy release process of an MCC with a specific structure.The shock wave pressure and explosive dispersion characteristics of the MCC under different initiation modes were compared.The forming and expanding process of the shock wave of the composite charge under different initiation modes was determined.The separation position of the shock wave and fireball interface was determined.The calculation formulas of the shock radius and overpressure of the composite charge are presented.The radius of the shock wave of the composite charge was significantly affected by the initiation mode.Moreover,the development process of the composite explosive fireball under different initiation modes was analyzed,the variation rules of the composite charge dispersion radius and fireball dispersion velocity with time were obtained under the different initiation modes,the explosion energy release rate of composite charge under simultaneous initiation modes was the highest,and the peak overpressure under the simultaneous initiation mode was 1.61 times that of central single-point initiation.展开更多
Phase-frequency characte ristics of approximate sinusoidal geomagnetic signals can be used fo r projectile roll positioning and other high-precision trajectory correction applications.The sinusoidal geomagnetic signal...Phase-frequency characte ristics of approximate sinusoidal geomagnetic signals can be used fo r projectile roll positioning and other high-precision trajectory correction applications.The sinusoidal geomagnetic signal deforms in the exposed and magnetically contaminated environment.In order to preciously recognize the roll information and effectively separate the noise component from the original geomagnetic sequence,based on the error source analysis,we propose a moving horizon based wavelet de-noising method for the dual-observed geomagnetic signal filtering where the captured rough roll frequency value provides reasonable wavelet decomposition and reconstruction level selection basis for sampled sequence;a moving horizon window guarantees real-time performance and non-cumulative calculation amount.The complete geomagnetic data in full ballistic range and three intercepted paragraphs are used for performance assessment.The positioning performance of the moving horizon wavelet de-noising method is compared with the band-pass filter.The results show that both noise reduction techniques improve the positioning accuracy while the wavelet de-noising method is always better than the band-pass filter.These results suggest that the proposed moving horizon based wavelet de-noising method of the dual-observed geomagnetic signal is more applicable for various launch conditions with better positioning performance.展开更多
In response to the demand for short-range detection of anti-smoke environment interference by laser fuzes,this study proposes a smoke environment simulation of non-uniform continuous point source diffusion and investi...In response to the demand for short-range detection of anti-smoke environment interference by laser fuzes,this study proposes a smoke environment simulation of non-uniform continuous point source diffusion and investigates an experimental laboratory smoke environment using an ammonium chloride smoke agent.The particle size distribution,composition,and mass flow distribution of the smoke were studied.Based on a discrete phase model and a kεturbulence model,a numerical simulation was developed to model the smoke generation and diffusion processes of the smoke agent in a confined space.The temporal and spatial distribution characteristics of the smoke mass concentration,velocity,and temperature in the space after smoke generation were analyzed,and the motion law governing the smoke diffusion throughout the entire space was summarized.Combined with the experimental verification of the smoke environment laboratory,the results showed that the smoke plume changed from fan-shaped to umbrella-shaped during smoke generation,and then continued to spread around.Meanwhile,the mass concentration of smoke in the space decreased from the middle outward;the changes in temperature and velocity were small and stable.In the diffusion stage(after 900 s),the mass concentration of smoke above 0.8 m was relatively uniform across an area of smoke that was 12 m thick.The concentration decreased over time,following a consistent decreasing trend,and the attenuation was negligible in a very short time.Therefore,this system was suitable for conducting experimental research on laser fuzes in a smoke environment.Owing to the stability of the equipment and facilities,the setup could reproduce the same experimental smoke environment by artificially controlling the smoke emission of the smoke agent.Overall,this work provides a theoretical reference for subsequent research efforts regarding the construction of uniform smoke environments and evaluating laser transmission characteristics in smoky environments.展开更多
In this study, 40 Cr Mn Si B steel cylindrical shells were tempered at 350, 500 and 600 ℃ to study the effect of tempering temperature on the dynamic process of expansion and fracture of the metal shell. A midexplosi...In this study, 40 Cr Mn Si B steel cylindrical shells were tempered at 350, 500 and 600 ℃ to study the effect of tempering temperature on the dynamic process of expansion and fracture of the metal shell. A midexplosion recovery experiment for the metal cylinder under internal explosive loading was designed, and the wreckage of the casings at the intermediate phase was obtained. The effects of different tempering temperatures on the macroscopic and microscopic fracture characteristics of 40 Cr Mn Si B steel were studied. The influence of tempering temperatures on the fracture characteristic parameters of the recovered wreckage were measured and analyzed, including the circumferential divide size, the thickness and the number of the circumferential divisions. The results show that as the tempering temperature was increased from 350 to 600 ℃, at first, the degree of fragmentation and the fracture characteristic parameters of the recovered wreckage changed significantly and then became essentially consistent. Scanning electron microscopy analysis revealed flow-like structure characteristics caused by adiabatic shear on different fracture surfaces. At the detonation initiation end of the casing, fracturing was formed by tearing along the crack, which existed a distance from the initiation end and propagated along the axis direction. In contrast, the fracturing near the middle position consists of a plurality of radial shear fracture units. The amount of alloy carbide that was precipitated during the tempering process increased continuously with tempering temperature, leading to an increasing number of spherical carbide particles scattered around the fracture surface.展开更多
A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted...A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted in a 1.3 m3tank and a 113 m3bunker.The blast parameters,including the quasistatic pressure(ΔpQS),special impulse(I),and peak overpressure(Δpmax),and images of the explosion process were recorded,and the influence of the Al content(30% and 50%) and Al particle size(1,10,and 50 μm) on the energy release of aluminum/rubber composites were investigated.The results revealed that the use of an active layer increased the peak overpressure generated by the primary blast wave,as well as the quasistatic pressure and special impulse related to fuel burning within tens of milliseconds after detonation.When the Al content was increased from 30% to 50%,the increases of ΔpQS and I were not obvious,and Δpmaxeven decreased,possibly because of decreased combustion efficiency and greater absorption of the blast wave energy for layers with 50% Al.Compared with the pure JH-2charge,the charge with 1 μm Al particles produced the highest Δpmax,indicating that better transient blast performance was generated by smaller Al particles.However,the charge with 10 μm Al particles showed the largest ΔpQSand I,suggesting that a stronger destructive effect occurred over a longer duration for charges that contained moderate 10 μm Al.展开更多
The design of terminally sensitive projectile scanning platform requires a better understanding of its aerodynamic characteristics.The terminally sensitive projectile with S-C fins has a complex aerodynamic shape,whic...The design of terminally sensitive projectile scanning platform requires a better understanding of its aerodynamic characteristics.The terminally sensitive projectile with S-C fins has a complex aerodynamic shape,which is constructed with small length to diameter ratio cylindrical body on which two low aspect ratio fins are installed.The study focuses on the effect of fin aspect ratio on the aerodynamic characteristics.Simulation was carried on based on computational fluid dynamics(CFD) method,and the pressure distribution characteristic,drag coefficient,lift coefficient and rolling moment coefficient varying with attack angle were obtained.A free flying experimental investigation focused on the kinetic aerodynamics was made.The results show that the fins provide sufficient drag to balance the terminally sensitive projectile weight to keep it flying at low and stable speed.The lift coefficient has a negative linear varying with attack angle.The rolling moment decrease with the increase in attack angle and the decrease in wing span area.展开更多
By using LS-DYNA simulation software,the influences of some structure parameters,such as top cone angle,wall thickness,liner height and height ratio of top cone,of double-angle liner on the jet formation were studied ...By using LS-DYNA simulation software,the influences of some structure parameters,such as top cone angle,wall thickness,liner height and height ratio of top cone,of double-angle liner on the jet formation were studied respectively.Their influences on jet tip velocity,tail velocity and penetration depth were revealed.The simulation results show that the formation is better if the top cone angle is selected as 28°,the wall is 2.6mm,the liner height is 140mm,and the height ratio of top cone is 60%.In large stand-off distance,the jet has a higher tip velocity,and the tip does not break.With the stand-off distance of 8 times of the charge diameter,the experiment penetrating steel target was carried out.The experiment and simulation results are in good agreement.展开更多
For shaped charges,LS-DYNA software was adopted to explore the influence of number of initiation points on the penetrator formation numerically.Changed the number of initiation points from 4 to 36,the performance of p...For shaped charges,LS-DYNA software was adopted to explore the influence of number of initiation points on the penetrator formation numerically.Changed the number of initiation points from 4 to 36,the performance of penetrator under four different kinds of typical charge diameter was analyzed,and the effect of detonation wave pressure on the liner was discussed.The minimum number of initiation points to substitute for annular initiation was obtained for each of four warheads with different charge diameters,and the curve representing the relation between the number of initiation points and charge diameter was found out also by using polynomial fitting.The simulation result provides a reference for the design of multimode warhead.展开更多
A control system for correction mechanisms through the whole trajectory is proposed based on the principle of one-dimensional trajectory correction projectile. Digital signal processing( DSP) is utilized as the core c...A control system for correction mechanisms through the whole trajectory is proposed based on the principle of one-dimensional trajectory correction projectile. Digital signal processing( DSP) is utilized as the core controller and gobal positioning system( GPS) is used to measure trajectory parameters to meet the requirements of calculating ballistics and system functions. Firstly,the hardware,mainly including communication module,ballistic calculation module,boosting& detonating module and data storage module,is designed. Secondly,the supporting software is developed based on the communication protocols of GPS and the workflow of control system. Finally,the feasibility and the reliability of the control system are verified through dynamic tests in a car and live firing experiments. The system lays a foundation for the research on trajectory correction projectile for the whole trajectory.展开更多
Supercapacitors(SCs)have been successfully used in electric vehicles or military equipment systems for their high power density.However,the mechanical impacts from vehicle crashes and missile penetration probably caus...Supercapacitors(SCs)have been successfully used in electric vehicles or military equipment systems for their high power density.However,the mechanical impacts from vehicle crashes and missile penetration probably cause performance fluctuations or failure of SCs,which may threaten the safety of systems using SCs.In this paper,a generalized circuit model to analyze the transient process of SCs under mechanical loads is proposed.The circuit model simultaneously takes capacitance change,internal short-circuit and resistance change into account,an extra resistor-capacitor circuit(RCC)is added to simulate the nonlinear behavior during charging and discharging.Subsequently,the relationships between pressure and fundamental circuit parameters are determined by static methods.By taking the static test data into the circuit model,the transient response of different types of SCs under particular mechanical loading conditions is predicted.Finally,the influences of some crucial parameters on the voltage responses of SCs are revealed based on the simulations,which provide references for designing and optimizing mechanical load-resistant or self-sensing SCs in specific application scenarios.展开更多
In modern warfare,fortifications are being placed deeper underground and with increased mechanical strength,placing higher demands on the target speed of the penetrating munitions that attack them.In such practical sc...In modern warfare,fortifications are being placed deeper underground and with increased mechanical strength,placing higher demands on the target speed of the penetrating munitions that attack them.In such practical scenarios,penetrating fuze inevitably experience extreme mechanical loads with long pulse durations and high shock strengths.Experimental results indicate that their shock accelerations can even exceed those of the projectile by several times.However,due to the unclear understanding of the dynamic transfer mechanism of the penetrating fuze system under such extreme mechanical conditions,there is still a lack of effective methods to accurately estimate and design protection against the impact loads on the penetrating fuze.This paper focuses on the dynamic response of penetrating munitions and fuzes under high impact,establishing a nonlinear dynamic transfer model for penetrating fuze systems,which can calculate the sensor overload signal of the fuze location.The results show that the relative error between the peak acceleration obtained by the proposed multibody dynamic transfer model and that obtained by experimental tests is only 15.7%,which is much lower than the 26.4%error between finite element simulations and experimental tests.The computational burden of the proposed method mainly lies in the parameter calibration process,which needs to be performed only once for a specific projectile‐fuze system.Once calibrated,the model can rapidly conduct parameter scanning simulations for the projectile mass,target plate strength,and impact velocity with an extremely low computational cost to obtain the response characteristics of the projectile‐fuze system under various operating conditions.This greatly facilitates the practical engineering design of penetrating ammunition fuze.展开更多
基金funded by the National Natural Science Foundation of China(Grant No.12302437)China Postdoctoral Science Foundation(Grant No.2021M701710)。
文摘This study proposed three types of Al—Hf reactive materials with particle size ratios(a),which were almost completely dense(porosity of<5.40%)owing to their preparation using hot-pressing technology.Microstructure characteristics and phase composition were analyzed,and the influence of particle size ratios on dynamic mechanical behavior and damage mechanism were investigated.The prepared sample with a=0.1 exhibited continuous wrapping of the Hf phase by the Al phase.Hf—Hf contact(continuous Hf phase)within the sample gradually increased with increasing a,and a small amount of fine Hf appeared for the sample with a=1.The reactive materials exhibited clear strain-rate sensitivity,with flow stressσ0.05and failure strainεfincreasing approximately linearly with increasing strain rate.ε.It is found that the plastic deformation of the material increased with increasing strain rate.As a increased from 0.1 to 1,the flow stress gradually increased.Impact failure of the material was dominated by ductile fracture with a large Al phase plastic deformation band for lower a,while brittle fracture with crushed Hf particles occurred at higher a.Finally,a constitutive model based on BP neural network was proposed to describe the stress-strain relationships of the materials,with an average relative error of 2.22%.
基金funded by the National Natural Science Foundation of China(Grant No.11972018,No.12002336)China Postdoctoral Science Foundation(Grant No.2021M701710)。
文摘This article investigates the characteristics of shock wave overpressure generated by multi-layer composite charge under different detonation modes.Combining dimensional analysis and the explosion mechanism of the charge,a peak overpressure prediction model for the composite charge under singlepoint detonation and simultaneous detonation was established.The effects of the charge structure and initiation method on the overpressure field characteristics were investigated in AUTODYN simulation.The accuracy of the prediction model and the reliability of the numerical simulation method were subsequently verified in a series of static explosion experiments.The results reveal that the mass of the inner charge was the key factor determining the peak overpressure of the composite charge under single-point detonation.The peak overpressure in the radial direction improved apparently with an increase in the aspect ratio of the charge.The overpressure curves in the axial direction exhibited a multi-peak phenomenon,and the secondary peak overpressure even exceeded the primary peak at distances of 30D and 40D(where D is the charge diameter).The difference in peak overpressure among azimuth angles of 0-90°gradually decreased with an increase in the propagation distance of the shock wave.The coupled effect of the detonation energy of the inner and outer charge under simultaneous detonation improved the overpressure in both radial and axial directions.The difference in peak overpressure obtained from model prediction and experimental measurements was less than 16.4%.
基金funded by the National Natural Science Foundation of China under NO.11202103Qing-lan Project of Jiangsu Province。
文摘The numerical simulation of a blast wave of a multilayer composite charge is investigated.A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program.Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25-0.5 cm and 1-3 cm.The Euler--fluxcorrected transport solver is found to be suitable for the far-field calculation after mapping.A numerical simulation is conducted to study the formation,propagation,and interaction of the shock wave of the composite charge for different initiation modes.It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge.Additionally,it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation,and the peak pressure of the shock wave exponentially decays,fitting the calculation formula of the peak overpressure attenuation under different initiation modes,which is obtained and verified by experiment.The difference between numerical and experimental results is less than 10%,and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.
文摘The influe nce of initiation modes on the explosive dispersion process of the multi-layer co mposite charge(MCC) was studied.Overpressure sensors and high-speed photography system were used to investigate the energy release process of an MCC with a specific structure.The shock wave pressure and explosive dispersion characteristics of the MCC under different initiation modes were compared.The forming and expanding process of the shock wave of the composite charge under different initiation modes was determined.The separation position of the shock wave and fireball interface was determined.The calculation formulas of the shock radius and overpressure of the composite charge are presented.The radius of the shock wave of the composite charge was significantly affected by the initiation mode.Moreover,the development process of the composite explosive fireball under different initiation modes was analyzed,the variation rules of the composite charge dispersion radius and fireball dispersion velocity with time were obtained under the different initiation modes,the explosion energy release rate of composite charge under simultaneous initiation modes was the highest,and the peak overpressure under the simultaneous initiation mode was 1.61 times that of central single-point initiation.
基金funded by National Natural Science Foundation of China(61201391)。
文摘Phase-frequency characte ristics of approximate sinusoidal geomagnetic signals can be used fo r projectile roll positioning and other high-precision trajectory correction applications.The sinusoidal geomagnetic signal deforms in the exposed and magnetically contaminated environment.In order to preciously recognize the roll information and effectively separate the noise component from the original geomagnetic sequence,based on the error source analysis,we propose a moving horizon based wavelet de-noising method for the dual-observed geomagnetic signal filtering where the captured rough roll frequency value provides reasonable wavelet decomposition and reconstruction level selection basis for sampled sequence;a moving horizon window guarantees real-time performance and non-cumulative calculation amount.The complete geomagnetic data in full ballistic range and three intercepted paragraphs are used for performance assessment.The positioning performance of the moving horizon wavelet de-noising method is compared with the band-pass filter.The results show that both noise reduction techniques improve the positioning accuracy while the wavelet de-noising method is always better than the band-pass filter.These results suggest that the proposed moving horizon based wavelet de-noising method of the dual-observed geomagnetic signal is more applicable for various launch conditions with better positioning performance.
基金the Central University Special Funding for Basic Scientific Research(Grant No.30918012201)the Foundation of JWKJW Field(Grant 2020-JCJQ-JJ-392)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX20_0315).
文摘In response to the demand for short-range detection of anti-smoke environment interference by laser fuzes,this study proposes a smoke environment simulation of non-uniform continuous point source diffusion and investigates an experimental laboratory smoke environment using an ammonium chloride smoke agent.The particle size distribution,composition,and mass flow distribution of the smoke were studied.Based on a discrete phase model and a kεturbulence model,a numerical simulation was developed to model the smoke generation and diffusion processes of the smoke agent in a confined space.The temporal and spatial distribution characteristics of the smoke mass concentration,velocity,and temperature in the space after smoke generation were analyzed,and the motion law governing the smoke diffusion throughout the entire space was summarized.Combined with the experimental verification of the smoke environment laboratory,the results showed that the smoke plume changed from fan-shaped to umbrella-shaped during smoke generation,and then continued to spread around.Meanwhile,the mass concentration of smoke in the space decreased from the middle outward;the changes in temperature and velocity were small and stable.In the diffusion stage(after 900 s),the mass concentration of smoke above 0.8 m was relatively uniform across an area of smoke that was 12 m thick.The concentration decreased over time,following a consistent decreasing trend,and the attenuation was negligible in a very short time.Therefore,this system was suitable for conducting experimental research on laser fuzes in a smoke environment.Owing to the stability of the equipment and facilities,the setup could reproduce the same experimental smoke environment by artificially controlling the smoke emission of the smoke agent.Overall,this work provides a theoretical reference for subsequent research efforts regarding the construction of uniform smoke environments and evaluating laser transmission characteristics in smoky environments.
基金funded by the National Natural Science Foundation of China (Grant No.11972018)sponsored by the Defense Pre-Research Joint Foundation of Chinese Ordnance Industry (Grant No. 6141B012858)。
文摘In this study, 40 Cr Mn Si B steel cylindrical shells were tempered at 350, 500 and 600 ℃ to study the effect of tempering temperature on the dynamic process of expansion and fracture of the metal shell. A midexplosion recovery experiment for the metal cylinder under internal explosive loading was designed, and the wreckage of the casings at the intermediate phase was obtained. The effects of different tempering temperatures on the macroscopic and microscopic fracture characteristics of 40 Cr Mn Si B steel were studied. The influence of tempering temperatures on the fracture characteristic parameters of the recovered wreckage were measured and analyzed, including the circumferential divide size, the thickness and the number of the circumferential divisions. The results show that as the tempering temperature was increased from 350 to 600 ℃, at first, the degree of fragmentation and the fracture characteristic parameters of the recovered wreckage changed significantly and then became essentially consistent. Scanning electron microscopy analysis revealed flow-like structure characteristics caused by adiabatic shear on different fracture surfaces. At the detonation initiation end of the casing, fracturing was formed by tearing along the crack, which existed a distance from the initiation end and propagated along the axis direction. In contrast, the fracturing near the middle position consists of a plurality of radial shear fracture units. The amount of alloy carbide that was precipitated during the tempering process increased continuously with tempering temperature, leading to an increasing number of spherical carbide particles scattered around the fracture surface.
基金funded by the National Natural Science Foundation of China(Grant No.11972018)the Defense Pre-Research Joint Foundation of Chinese Ordnance Industry(Grant No.6141B012858)。
文摘A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted in a 1.3 m3tank and a 113 m3bunker.The blast parameters,including the quasistatic pressure(ΔpQS),special impulse(I),and peak overpressure(Δpmax),and images of the explosion process were recorded,and the influence of the Al content(30% and 50%) and Al particle size(1,10,and 50 μm) on the energy release of aluminum/rubber composites were investigated.The results revealed that the use of an active layer increased the peak overpressure generated by the primary blast wave,as well as the quasistatic pressure and special impulse related to fuel burning within tens of milliseconds after detonation.When the Al content was increased from 30% to 50%,the increases of ΔpQS and I were not obvious,and Δpmaxeven decreased,possibly because of decreased combustion efficiency and greater absorption of the blast wave energy for layers with 50% Al.Compared with the pure JH-2charge,the charge with 1 μm Al particles produced the highest Δpmax,indicating that better transient blast performance was generated by smaller Al particles.However,the charge with 10 μm Al particles showed the largest ΔpQSand I,suggesting that a stronger destructive effect occurred over a longer duration for charges that contained moderate 10 μm Al.
文摘The design of terminally sensitive projectile scanning platform requires a better understanding of its aerodynamic characteristics.The terminally sensitive projectile with S-C fins has a complex aerodynamic shape,which is constructed with small length to diameter ratio cylindrical body on which two low aspect ratio fins are installed.The study focuses on the effect of fin aspect ratio on the aerodynamic characteristics.Simulation was carried on based on computational fluid dynamics(CFD) method,and the pressure distribution characteristic,drag coefficient,lift coefficient and rolling moment coefficient varying with attack angle were obtained.A free flying experimental investigation focused on the kinetic aerodynamics was made.The results show that the fins provide sufficient drag to balance the terminally sensitive projectile weight to keep it flying at low and stable speed.The lift coefficient has a negative linear varying with attack angle.The rolling moment decrease with the increase in attack angle and the decrease in wing span area.
文摘By using LS-DYNA simulation software,the influences of some structure parameters,such as top cone angle,wall thickness,liner height and height ratio of top cone,of double-angle liner on the jet formation were studied respectively.Their influences on jet tip velocity,tail velocity and penetration depth were revealed.The simulation results show that the formation is better if the top cone angle is selected as 28°,the wall is 2.6mm,the liner height is 140mm,and the height ratio of top cone is 60%.In large stand-off distance,the jet has a higher tip velocity,and the tip does not break.With the stand-off distance of 8 times of the charge diameter,the experiment penetrating steel target was carried out.The experiment and simulation results are in good agreement.
文摘For shaped charges,LS-DYNA software was adopted to explore the influence of number of initiation points on the penetrator formation numerically.Changed the number of initiation points from 4 to 36,the performance of penetrator under four different kinds of typical charge diameter was analyzed,and the effect of detonation wave pressure on the liner was discussed.The minimum number of initiation points to substitute for annular initiation was obtained for each of four warheads with different charge diameters,and the curve representing the relation between the number of initiation points and charge diameter was found out also by using polynomial fitting.The simulation result provides a reference for the design of multimode warhead.
文摘A control system for correction mechanisms through the whole trajectory is proposed based on the principle of one-dimensional trajectory correction projectile. Digital signal processing( DSP) is utilized as the core controller and gobal positioning system( GPS) is used to measure trajectory parameters to meet the requirements of calculating ballistics and system functions. Firstly,the hardware,mainly including communication module,ballistic calculation module,boosting& detonating module and data storage module,is designed. Secondly,the supporting software is developed based on the communication protocols of GPS and the workflow of control system. Finally,the feasibility and the reliability of the control system are verified through dynamic tests in a car and live firing experiments. The system lays a foundation for the research on trajectory correction projectile for the whole trajectory.
基金the National Natural Science Foundation of China(No.52007084)the Natural Science Foundation of Jiangsu Province under Grant(No.BK20190470).
文摘Supercapacitors(SCs)have been successfully used in electric vehicles or military equipment systems for their high power density.However,the mechanical impacts from vehicle crashes and missile penetration probably cause performance fluctuations or failure of SCs,which may threaten the safety of systems using SCs.In this paper,a generalized circuit model to analyze the transient process of SCs under mechanical loads is proposed.The circuit model simultaneously takes capacitance change,internal short-circuit and resistance change into account,an extra resistor-capacitor circuit(RCC)is added to simulate the nonlinear behavior during charging and discharging.Subsequently,the relationships between pressure and fundamental circuit parameters are determined by static methods.By taking the static test data into the circuit model,the transient response of different types of SCs under particular mechanical loading conditions is predicted.Finally,the influences of some crucial parameters on the voltage responses of SCs are revealed based on the simulations,which provide references for designing and optimizing mechanical load-resistant or self-sensing SCs in specific application scenarios.
基金Key Basic Research Projects of Basic Strengthening Plan of China,Grant/Award Number:2021-JCJQ-JJ-0597National Natural Science Foundation of China,Grant/Award Number:52007084Postgraduate Research Practice Innovation Program of Jiangsu Province,Grant/Award Number:KYCX23_0518。
文摘In modern warfare,fortifications are being placed deeper underground and with increased mechanical strength,placing higher demands on the target speed of the penetrating munitions that attack them.In such practical scenarios,penetrating fuze inevitably experience extreme mechanical loads with long pulse durations and high shock strengths.Experimental results indicate that their shock accelerations can even exceed those of the projectile by several times.However,due to the unclear understanding of the dynamic transfer mechanism of the penetrating fuze system under such extreme mechanical conditions,there is still a lack of effective methods to accurately estimate and design protection against the impact loads on the penetrating fuze.This paper focuses on the dynamic response of penetrating munitions and fuzes under high impact,establishing a nonlinear dynamic transfer model for penetrating fuze systems,which can calculate the sensor overload signal of the fuze location.The results show that the relative error between the peak acceleration obtained by the proposed multibody dynamic transfer model and that obtained by experimental tests is only 15.7%,which is much lower than the 26.4%error between finite element simulations and experimental tests.The computational burden of the proposed method mainly lies in the parameter calibration process,which needs to be performed only once for a specific projectile‐fuze system.Once calibrated,the model can rapidly conduct parameter scanning simulations for the projectile mass,target plate strength,and impact velocity with an extremely low computational cost to obtain the response characteristics of the projectile‐fuze system under various operating conditions.This greatly facilitates the practical engineering design of penetrating ammunition fuze.
