Taking the pilot test area of polymer enhanced foam flooding in Y oilfield as the prototype, a numerical core model was established, and the polymer enhanced foam formulation system was optimized by analyzing the resi...Taking the pilot test area of polymer enhanced foam flooding in Y oilfield as the prototype, a numerical core model was established, and the polymer enhanced foam formulation system was optimized by analyzing the resistance factor and the change rule of oil recovery of different formulation systems. Research shows that the higher the polymer concentration, the greater the resistance factor, and the more obvious the sealing effect formed in the formation. The concentration of surfactant has a greater impact on the resistance factor. With the increase of surfactant concentration, the resistance factor increases significantly, and the plugging effect of foam agent on core is significantly enhanced. With the increase of gas-liquid ratio, the resistance factor first increases and then decreases. When the gas-liquid ratio is 1:1, the resistance is the largest, and the foam agent has the strongest plugging effect on the core. The optimal formula system of polymer enhanced foam flooding in Y oilfield is: polymer concentration is 1200 mg/L, surfactant concentration is 0.25 wt%, gas-liquid ratio is 1:1.展开更多
<span style="font-family:""><span style="font-family:Verdana;">Northern Niayes is an area where agriculture is the main activity. Water used for irrigation in this area comes exclu...<span style="font-family:""><span style="font-family:Verdana;">Northern Niayes is an area where agriculture is the main activity. Water used for irrigation in this area comes exclusively from groundwater. Farmers do not have access to electricity, thus fuel is the main source of energy used, which is very expensive. The objective of this study was to assess the techno-economic feasibility of solar irrigation pumps. Regarding technical feasibility, pump sizing was carried out on the basis of irrigation management, irrigation techniques, and water distribution. Also, the economic feasibility was studied on the basis of the Net Present Value, Benefit-Cost Ratio, Internal Rate of Return and Payback Period. Results showed for cultivated area ranging from 0.05 ha to 1.91 ha, pumps’ flow rate does not vary greatly from one irrigation technique to another. It varies between 2.5 m</span><sup><span style="font-family:Verdana;">3</span></sup><span style="font-family:Verdana;">/h and 31 m</span><sup><span style="font-family:Verdana;">3</span></sup><span style="font-family:Verdana;">/h. However, pressure and power are higher when using drip and sprinkler irrigation techniques, ranging from 27.8 m to 39.9 m for drip and 40.1 m to 58.5 m for sprinkler irrigation. The power varies between 0.05 kW and 1.6 kW for manual, between 0.05 kW and 2.5 kW for drip and between 0.1 kW and 4.75 kW for sprinkler irrigation. The investment cost is variable (669 euros to 21,400 euros), depending on the cultivated area, pump brands and characteristics, and irrigation techniques. Results show that the investment cost ranges from 669 euros (438,500 CFA) to 4090 euros (2,683,000 CFA) when using the manual irrigation technique, from 1281 euros to 20</span></span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;">600 euros when using the drip irrigation technique and from 819 euros to 21</span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;">403 euros when using sprinkler irrigation technique for individual pumps. The investment cost is higher when using reservoirs. In this case, the investment cost varied between €722 and €6062 for manual irrigation, €1532 and €25,882 for drip irrigation and €900 and €28,000 for sprinkling. However, the total investment cost at the entire lowland scale is higher when farmers use the pumps individually and lower when farmers use the pumps in groups when using manual and drip irrigation techniques. NPV varies between 15,993€ (0.75 ha) and 103,139€ (1.41 ha) and between 13,064€ and 86,139€ when using sprinkler irrigation techniques with PVC pipes and when using the drip irrigation technique, respectively. BCR is estimated to average 2.2, 2, and 2 respectively when using manual, drip, and sprinkler irrigation techniques. In addition, PBP is reached more rapidly when using the manual irrigation technique</span><span style="font-family:Verdana;">.</span>展开更多
Bulk metallic glass and their composites (BMGMCs) are a new class of materials which possess superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates ...Bulk metallic glass and their composites (BMGMCs) are a new class of materials which possess superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates for tomorrow’s structural applications. However, they suffer from poor ductility and little or no toughness which render them brittle and they manifest catastrophic failure under applied force. Their behavior is dubious, unpredictable and requires extensive experimentation to arrive at conclusive results. In present study, an effort has been made to design bulk metallic glass matrix composites by the use of modeling and simulation. A probabilistic cellular automaton (CA) model is developed and described in present study by author which is used in conjunction with earlier developed deterministic model to predict microstructural evolution in Zr based BMGMCs in additive manufacturing liquid melt pool. It is elaborately described with an aim to arrive at quantitative relations which describe process and steps of operations. Results indicate that effect of incorporating all mass transfer and diffusion coefficients under transient conditions and precise determination of probability number play a vital role in refining the model and bringing it closer to a level that it could be compared to actual values. It is shown that proposed tailoring can account for microstructural evolution in metallic glasses.展开更多
Reductions in CO2 emissions have a significant effect on the transportation sector, and there is increasing interest in developing green cars such as electric cars. To prepare for the advent of the electric car era, i...Reductions in CO2 emissions have a significant effect on the transportation sector, and there is increasing interest in developing green cars such as electric cars. To prepare for the advent of the electric car era, it will be necessary to predict the increase in electricity demand owing to the spread of electric cars and determine the policy approaches. Therefore, the analysis was performed to promote the use of electric car that helps reduce CO2 emissions. This study establishes a mode choice model using the stated preference method. To improve the predictive power of the model, some revealed preference data were also examined to consider the characteristics of the commuters and the extent of current electric car technology to determine and verify the parameters of the mode choice models. This was used to estimate changes in CO2 emissions owing to the introduction of electric cars and present effective policy approaches to reduce CO2 emissions.展开更多
In the article the research of cotton seeds for the purpose of increasing the fiber in the enterprise is investigated, separated from the mass of the derivatives of ginning of fibrous seeds by means of effective clean...In the article the research of cotton seeds for the purpose of increasing the fiber in the enterprise is investigated, separated from the mass of the derivatives of ginning of fibrous seeds by means of effective cleaning and sorting on the mesh surface.展开更多
This paper analyzes the effect of subgroup size on the x-bar chart characteristics using sample influx (SIF) into forensic science laboratory (FSL). The characteristics studied include changes in out-or-control points...This paper analyzes the effect of subgroup size on the x-bar chart characteristics using sample influx (SIF) into forensic science laboratory (FSL). The characteristics studied include changes in out-or-control points (OCP), upper control limit UCLx, and zonal demarcations. Multi-rules were used to identify the number of out-of-control-points, Nocp as violations using five control chart rules applied separately. A sensitivity analysis on the Nocp was applied for subgroup size, k, and number of sigma above the mean value to determine the upper control limit, UCLx. A computer code was implemented using a FORTRAN code to create x-bar control-charts and capture OCP and other control-chart characteristics with increasing k from 2 to 25. For each value of k, a complete series of average values, Q(p), of specific length, Nsg, was created from which statistical analysis was conducted and compared to the original SIF data, S(t). The variation of number of out-of-control points or violations, Nocp, for different control-charts rules with increasing k was determined to follow a decaying exponential function, Nocp = Ae–α, for which, the goodness of fit was established, and the R2 value approached unity for Rule #4 and #5 only. The goodness of fit was established to be the new criteria for rational subgroup-size range, for Rules #5 and #4 only, which involve a count of 6 consecutive points decreasing and 8 consecutive points above the selected control limit (σ/3 above the grand mean), respectively. Using this criterion, the rational subgroup range was established to be 4 ≤ k ≤ 20 for the two x-bar control chart rules.展开更多
As a reliability quantitative specification, parametric accelerated life testing was used to assess the reliability of a newly designed compressor of a commercial refrigerator subjected to repetitive stresses. A gener...As a reliability quantitative specification, parametric accelerated life testing was used to assess the reliability of a newly designed compressor of a commercial refrigerator subjected to repetitive stresses. A generalized life-stress failure model and new sample size equation with a new load concept were derived starting with the basic refrigeration cycle. The sample size equation with the acceleration factor also enabled the parametric accelerated life testing to quickly evaluate the expected lifetime. The design of this testing should help an engineer uncover the design parameters affecting reliability during the design process of the compressor system. Consequently, it should help companies improve product reliability and avoid recalls due to the product failures in the field. A newly designed compressor in a commercial refrigerator was used as a test case.展开更多
In this paper, we give a smoothing neural network algorithm for absolute value equations (AVE). By using smoothing function, we reformulate the AVE as a differentiable unconstrained optimization and we establish a ste...In this paper, we give a smoothing neural network algorithm for absolute value equations (AVE). By using smoothing function, we reformulate the AVE as a differentiable unconstrained optimization and we establish a steep descent method to solve it. We prove the stability and the equilibrium state of the neural network to be a solution of the AVE. The numerical tests show the efficient of the proposed algorithm.展开更多
The level of automation in the manufacture of recreational aluminum boats is very low. Robotized welding is rarely utilized, although it is commonly considered as the most effective way to reduce costs and increase co...The level of automation in the manufacture of recreational aluminum boats is very low. Robotized welding is rarely utilized, although it is commonly considered as the most effective way to reduce costs and increase competitiveness. A reason for the under-exploitation of robotics can be found in the construction of aluminum boats;boat models and their detailed structures are almost without exception individual pieces. A new stiffener structure for an aluminum recreational boat hull is developed in this work. Construction of the stiffener as a module allows exploitation of the advantages of modularization. The number of different parts is reduced and the structure simplified improves the applicability of robotic welding and provides benefits accruing from mass production. The same module can be used in several boat models. The modularity also makes it possible to use the same advanced robot welding fixture for a variety of boat models.展开更多
This paper presents two systems for recognizing static signs (digits) from American Sign Language (ASL). These systems avoid the use color marks, or gloves, using instead, low-pass and high-pass filters in space and f...This paper presents two systems for recognizing static signs (digits) from American Sign Language (ASL). These systems avoid the use color marks, or gloves, using instead, low-pass and high-pass filters in space and frequency domains, and color space transformations. First system used rotational signatures based on a correlation operator;minimum distance was used for the classification task. Second system computed the seven Hu invariants from binary images;these descriptors fed to a Multi-Layer Perceptron (MLP) in order to recognize the 9 different classes. First system achieves 100% of recognition rate with leaving-one-out validation and second experiment performs 96.7% of recognition rate with Hu moments and 100% using 36 normalized moments and k-fold cross validation.展开更多
The hydrocarbon deposits have stimulated worldwide efforts to understand gas production from hydrate dissociation in hydrate reservoirs well. This paper deals with the potential of gas hydrates as a source of energy w...The hydrocarbon deposits have stimulated worldwide efforts to understand gas production from hydrate dissociation in hydrate reservoirs well. This paper deals with the potential of gas hydrates as a source of energy which is widely available in permafrost and oceanic sediments. It discusses methods for gas production from natural gas hydrates. Authors provide a detailed methodology used to model gas productivity recovery from hydrate reservoir well. The mathematical modelling of gas dissociation from hydrate reservoir as a tool for evaluating the potential of gas hydrates for natural gas production. The simulation results show that the process of natural gas production in a hydrate reservoir is a sensitive function of reservoir temperature and hydrate zone permeability. The model couples nth order decomposition kinetics with gas flow through porous media. The models provide a simple and useful tool for hydrate reservoir analysis.展开更多
A computer simulation of the blood flow in a patient specific atherosclerotic right coronary artery is carried out to study the blood flow pattern and the wall shear stress (WSS) distribution in the artery. Both tempo...A computer simulation of the blood flow in a patient specific atherosclerotic right coronary artery is carried out to study the blood flow pattern and the wall shear stress (WSS) distribution in the artery. Both temporal and special distribution patterns of the WSS of the non-Newtonian blood flow are presented and the regions on the lumen surface where the WSS is constantly lower than 1N/m2are identified.展开更多
Automatic segmentation of liver in medical images is challenging on the aspects of accuracy, automation and robustness. A crucial stage of the liver segmentation is the selection of the image features for the segmenta...Automatic segmentation of liver in medical images is challenging on the aspects of accuracy, automation and robustness. A crucial stage of the liver segmentation is the selection of the image features for the segmentation. This paper presents an accurate liver segmentation algorithm. The approach starts with a texture analysis which results in an optimal set of texture features including high order statistical texture features and anatomical structural features. Then, it creates liver distribution image by classifying the original image pixelwisely using support vector machines. Lastly, it uses a group of morphological operations to locate the liver organ accurately in the image. The novelty of the approach is resided in the fact that the features are so selected that both local and global texture distributions are considered, which is important in liver organ segmentation where neighbouring tissues and organs have similar greyscale distributions. Experiment results of liver segmentation on CT images using the proposed method are presented with performance validation and discussion.展开更多
Laparoscopic surgery is a new abdominal surgical procedure which helps the patients in many ways like less hospital stay, faster recovery and reduced pain. The main disadvantage in this surgical procedure is the reduc...Laparoscopic surgery is a new abdominal surgical procedure which helps the patients in many ways like less hospital stay, faster recovery and reduced pain. The main disadvantage in this surgical procedure is the reduced haptic perception by the surgeons due to the usage of laparoscopic instrument to handle tissues which in turn cause damage of it as compared to an open surgery. The primary aim of this investigation was to compare the pinch force applied during two different methods of laparoscopic grasping: Finger and Palm grasp. A low cost force sensing resistor tailor made for the grasper tip was designed and fabricated for quantifying the grasper tip force in the study. The results indicate more pinch force was applied during palm grasp as compared to finger grasp so as to prevent the slippage of the tissues from the jaws of the laparoscopic graspers.展开更多
Recently, research strives to apply Ultra High Performance Concrete (UHPC) to large-sized structures owing to its remarkable mechanical performance and durability compared to normal concrete. The Korea Institute of Co...Recently, research strives to apply Ultra High Performance Concrete (UHPC) to large-sized structures owing to its remarkable mechanical performance and durability compared to normal concrete. The Korea Institute of Construction Technology proposed SuperBridge800, an edge girder type UHPC cable stayed bridge with central span of 800 m, through its detailed design. The bridge is designed to be erected through the connection of precast UHPC segments. The precast UHPC segment is monolithically composed of one ribbed deck slab and edge girders at each side. The connection between the precast segments is achieved by steel bars at the edge girders and by UHPC cast-in-place wet joint at the slab. Despite of the outstanding mechanical performance of UHPC, the fabrication of large-sized members is a difficult task since UHPC hardens faster than normal concrete and requires a special curing process. Therefore, the constructability of large-sized UHPC segment should be secured to achieve SuperBridge800. Besides, the performance of the connection between segments should also be guaranteed, especially in terms of the fatigue performance of the UHPC cast-in-place joint, which constitutes a weak point. To that goal, two half-scaled UHPC segments are manufactured and the constructability is examined by fabricating a large-sized UHPC member connected with respect to the design conditions. This study conducts rolling fatigue test on the so-fabricated large-sized UHPC member. Rolling fatigue test is carried out up to 2 million cycles considering actual vehicle load at each center and quarter points of the member. The test results confirm that the service limit state is satisfied.展开更多
In this study, polymorphisms of the DGAT1 andSTAT5A genes were detected in 528 individuals from Xinong Saanen and Guanzhong goat breeds by PCR-RFLP, PCR-SSCP and DNA sequencing methods. Three allelic variants were ide...In this study, polymorphisms of the DGAT1 andSTAT5A genes were detected in 528 individuals from Xinong Saanen and Guanzhong goat breeds by PCR-RFLP, PCR-SSCP and DNA sequencing methods. Three allelic variants were identified: DQ380250: g.407_408insC, AJ237937: g.6798C>T and g.6852C>T in both breeds. At g.407_408insC locus, the frequencies of C1 allele were 0.79–0.85, and frequencies of C2 allele were 0.21–0.15. At g.6852C>T locus, frequencies of C3 allele were 0.70–0.72, and frequencies of T3 allele were 0.30–0.28. Compared with goats with C1C1 and C3C3, those with C1C2 and C3T3 genotypes had significant effects on milk yield and fat percentage (P<0.05), respectively. The result showed that does with C1C1C3T3 and C1C2C3T3 had higher milk yield than those with C1C2C3C3 (P < 0.05). In addition, the combined effect of C1C2C3C3 on milk fat percentage was the highest in comparison with other combination genotypes (P<0.05).展开更多
Nine strains of ammonia nitrogen degradation strains from C1 to C9 were isolated from industrial wastewater to study their degradation and conversion of ammonia nitrogen. The results showed that C2 strain with a high ...Nine strains of ammonia nitrogen degradation strains from C1 to C9 were isolated from industrial wastewater to study their degradation and conversion of ammonia nitrogen. The results showed that C2 strain with a high degradation activiity of ammonia nitrogen, and the ammonia nitrogen degradation rate of the activated C2 strain was 93% within 24 h when the initial concentration of ammonia nitrogen was 200 mg/L under the conditions of inoculation 10%, temperature 35?C, pH 7.0, rotation 200 r/min. And C2 was identified as Bacillus amyloliquefaciens.展开更多
A solution containing Cr(VI), Cr(NO3)3 and its complex with an organic acid as well as several commercial solutions containing Cr(III) complexes with an organic acid and additionally CO2+, F-, SO42- ions were used for...A solution containing Cr(VI), Cr(NO3)3 and its complex with an organic acid as well as several commercial solutions containing Cr(III) complexes with an organic acid and additionally CO2+, F-, SO42- ions were used for the studies. Results of the studies obtained in the following commercial solutions: Likonda 2AT, Cr(NO3)3 + malonic acid;Likonda 3Cr5 and Likonda 3CrMC are discussed. Steel coated with chromated Zn coatings was contaminated by some microscopic fungi. The variety of fungi on chromated plates diminished, however the propagules of fungi did not disappear completely. The Likonda 3Cr5 solution diminishes fungi contamination on chromated steel most effectively. In water used to rinse the surface of chromated plates the number of fungi propagules was detected to be higher as compared to that on the plate surface. The least quantity of fungi propagules was detected in water used to rinse plates coated in the Likonda 3Cr5 solution. The main part of fungi detected on chromated plates treated in the Likonda 3Cr5 solution were the fungi of Cladosporium species (C.herbarum, C.cladosporioides). The latter species also dominated on chromated plates coated with zinc and treated with the other solution. It should be mentioned, that on these plates chromated in this solution, Actinomycetes of the Streptomyces group were abundant. After comparison of surfaces of the plates treated in four solutions it has been determined that the surface of the plates treated in the Likonda 3Cr5 passivation solution and exposed to modelling conditions changed least of all. It has been noticed that on the subject studied white porous rust accumulates, the intensity of this process on the surface studied determines both the probability of corrosion and the resistance of the used safety means to the external factors.展开更多
In this paper, we investigate the stator wake variability along the axial direction under different rotating speeds and mass flow conditions, in the terms of wake-core position, wake depth, wake width and wake velocit...In this paper, we investigate the stator wake variability along the axial direction under different rotating speeds and mass flow conditions, in the terms of wake-core position, wake depth, wake width and wake velocity gradient. Experimental study is carried out in a single stage axial compressor by using Hot-wire Anemometer (HWA). Simultaneously, the numerical calculation is brought out in the same experiment rig. Firstly, we analyze the time-averaged velocity and radial vorticity at different axial positions, and explore the wake variability along the axial direction. Then, we present the effects of operation conditions on the wake-core position, and find out the inlet Mach number and incident angle are both the key influence factors of the wake-core position. Finally, we summarize four preliminary conclusions of the wake variability.展开更多
The present study considers a finite element analysis of elastic-plastic axi-symmetric hemispherical contact for a frictionless deformable sphere pressed by a rigid flat. The material of the sphere is modeled as elast...The present study considers a finite element analysis of elastic-plastic axi-symmetric hemispherical contact for a frictionless deformable sphere pressed by a rigid flat. The material of the sphere is modeled as elastic perfectly plastic. Analysis is carried out to study the effect of varying modulus of elasticity and sphere radius in wide range of dimensionless interference until the inception of plasticity as well as in plastic range. Results are compared with previous elastic-plastic models. It is found that materials with Young’s modulus to yield strength (E/Y) ratio less than and greater than 300 show strikingly different contact phenomena. The dependency of E on dimensionless interference at which the plastic region fully covers the surface is observed. However with different radius, finite element study exhibits similar elastic-plastic phenomena.展开更多
文摘Taking the pilot test area of polymer enhanced foam flooding in Y oilfield as the prototype, a numerical core model was established, and the polymer enhanced foam formulation system was optimized by analyzing the resistance factor and the change rule of oil recovery of different formulation systems. Research shows that the higher the polymer concentration, the greater the resistance factor, and the more obvious the sealing effect formed in the formation. The concentration of surfactant has a greater impact on the resistance factor. With the increase of surfactant concentration, the resistance factor increases significantly, and the plugging effect of foam agent on core is significantly enhanced. With the increase of gas-liquid ratio, the resistance factor first increases and then decreases. When the gas-liquid ratio is 1:1, the resistance is the largest, and the foam agent has the strongest plugging effect on the core. The optimal formula system of polymer enhanced foam flooding in Y oilfield is: polymer concentration is 1200 mg/L, surfactant concentration is 0.25 wt%, gas-liquid ratio is 1:1.
文摘<span style="font-family:""><span style="font-family:Verdana;">Northern Niayes is an area where agriculture is the main activity. Water used for irrigation in this area comes exclusively from groundwater. Farmers do not have access to electricity, thus fuel is the main source of energy used, which is very expensive. The objective of this study was to assess the techno-economic feasibility of solar irrigation pumps. Regarding technical feasibility, pump sizing was carried out on the basis of irrigation management, irrigation techniques, and water distribution. Also, the economic feasibility was studied on the basis of the Net Present Value, Benefit-Cost Ratio, Internal Rate of Return and Payback Period. Results showed for cultivated area ranging from 0.05 ha to 1.91 ha, pumps’ flow rate does not vary greatly from one irrigation technique to another. It varies between 2.5 m</span><sup><span style="font-family:Verdana;">3</span></sup><span style="font-family:Verdana;">/h and 31 m</span><sup><span style="font-family:Verdana;">3</span></sup><span style="font-family:Verdana;">/h. However, pressure and power are higher when using drip and sprinkler irrigation techniques, ranging from 27.8 m to 39.9 m for drip and 40.1 m to 58.5 m for sprinkler irrigation. The power varies between 0.05 kW and 1.6 kW for manual, between 0.05 kW and 2.5 kW for drip and between 0.1 kW and 4.75 kW for sprinkler irrigation. The investment cost is variable (669 euros to 21,400 euros), depending on the cultivated area, pump brands and characteristics, and irrigation techniques. Results show that the investment cost ranges from 669 euros (438,500 CFA) to 4090 euros (2,683,000 CFA) when using the manual irrigation technique, from 1281 euros to 20</span></span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;">600 euros when using the drip irrigation technique and from 819 euros to 21</span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;">403 euros when using sprinkler irrigation technique for individual pumps. The investment cost is higher when using reservoirs. In this case, the investment cost varied between €722 and €6062 for manual irrigation, €1532 and €25,882 for drip irrigation and €900 and €28,000 for sprinkling. However, the total investment cost at the entire lowland scale is higher when farmers use the pumps individually and lower when farmers use the pumps in groups when using manual and drip irrigation techniques. NPV varies between 15,993€ (0.75 ha) and 103,139€ (1.41 ha) and between 13,064€ and 86,139€ when using sprinkler irrigation techniques with PVC pipes and when using the drip irrigation technique, respectively. BCR is estimated to average 2.2, 2, and 2 respectively when using manual, drip, and sprinkler irrigation techniques. In addition, PBP is reached more rapidly when using the manual irrigation technique</span><span style="font-family:Verdana;">.</span>
文摘Bulk metallic glass and their composites (BMGMCs) are a new class of materials which possess superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates for tomorrow’s structural applications. However, they suffer from poor ductility and little or no toughness which render them brittle and they manifest catastrophic failure under applied force. Their behavior is dubious, unpredictable and requires extensive experimentation to arrive at conclusive results. In present study, an effort has been made to design bulk metallic glass matrix composites by the use of modeling and simulation. A probabilistic cellular automaton (CA) model is developed and described in present study by author which is used in conjunction with earlier developed deterministic model to predict microstructural evolution in Zr based BMGMCs in additive manufacturing liquid melt pool. It is elaborately described with an aim to arrive at quantitative relations which describe process and steps of operations. Results indicate that effect of incorporating all mass transfer and diffusion coefficients under transient conditions and precise determination of probability number play a vital role in refining the model and bringing it closer to a level that it could be compared to actual values. It is shown that proposed tailoring can account for microstructural evolution in metallic glasses.
文摘Reductions in CO2 emissions have a significant effect on the transportation sector, and there is increasing interest in developing green cars such as electric cars. To prepare for the advent of the electric car era, it will be necessary to predict the increase in electricity demand owing to the spread of electric cars and determine the policy approaches. Therefore, the analysis was performed to promote the use of electric car that helps reduce CO2 emissions. This study establishes a mode choice model using the stated preference method. To improve the predictive power of the model, some revealed preference data were also examined to consider the characteristics of the commuters and the extent of current electric car technology to determine and verify the parameters of the mode choice models. This was used to estimate changes in CO2 emissions owing to the introduction of electric cars and present effective policy approaches to reduce CO2 emissions.
文摘In the article the research of cotton seeds for the purpose of increasing the fiber in the enterprise is investigated, separated from the mass of the derivatives of ginning of fibrous seeds by means of effective cleaning and sorting on the mesh surface.
文摘This paper analyzes the effect of subgroup size on the x-bar chart characteristics using sample influx (SIF) into forensic science laboratory (FSL). The characteristics studied include changes in out-or-control points (OCP), upper control limit UCLx, and zonal demarcations. Multi-rules were used to identify the number of out-of-control-points, Nocp as violations using five control chart rules applied separately. A sensitivity analysis on the Nocp was applied for subgroup size, k, and number of sigma above the mean value to determine the upper control limit, UCLx. A computer code was implemented using a FORTRAN code to create x-bar control-charts and capture OCP and other control-chart characteristics with increasing k from 2 to 25. For each value of k, a complete series of average values, Q(p), of specific length, Nsg, was created from which statistical analysis was conducted and compared to the original SIF data, S(t). The variation of number of out-of-control points or violations, Nocp, for different control-charts rules with increasing k was determined to follow a decaying exponential function, Nocp = Ae–α, for which, the goodness of fit was established, and the R2 value approached unity for Rule #4 and #5 only. The goodness of fit was established to be the new criteria for rational subgroup-size range, for Rules #5 and #4 only, which involve a count of 6 consecutive points decreasing and 8 consecutive points above the selected control limit (σ/3 above the grand mean), respectively. Using this criterion, the rational subgroup range was established to be 4 ≤ k ≤ 20 for the two x-bar control chart rules.
文摘As a reliability quantitative specification, parametric accelerated life testing was used to assess the reliability of a newly designed compressor of a commercial refrigerator subjected to repetitive stresses. A generalized life-stress failure model and new sample size equation with a new load concept were derived starting with the basic refrigeration cycle. The sample size equation with the acceleration factor also enabled the parametric accelerated life testing to quickly evaluate the expected lifetime. The design of this testing should help an engineer uncover the design parameters affecting reliability during the design process of the compressor system. Consequently, it should help companies improve product reliability and avoid recalls due to the product failures in the field. A newly designed compressor in a commercial refrigerator was used as a test case.
文摘In this paper, we give a smoothing neural network algorithm for absolute value equations (AVE). By using smoothing function, we reformulate the AVE as a differentiable unconstrained optimization and we establish a steep descent method to solve it. We prove the stability and the equilibrium state of the neural network to be a solution of the AVE. The numerical tests show the efficient of the proposed algorithm.
文摘The level of automation in the manufacture of recreational aluminum boats is very low. Robotized welding is rarely utilized, although it is commonly considered as the most effective way to reduce costs and increase competitiveness. A reason for the under-exploitation of robotics can be found in the construction of aluminum boats;boat models and their detailed structures are almost without exception individual pieces. A new stiffener structure for an aluminum recreational boat hull is developed in this work. Construction of the stiffener as a module allows exploitation of the advantages of modularization. The number of different parts is reduced and the structure simplified improves the applicability of robotic welding and provides benefits accruing from mass production. The same module can be used in several boat models. The modularity also makes it possible to use the same advanced robot welding fixture for a variety of boat models.
文摘This paper presents two systems for recognizing static signs (digits) from American Sign Language (ASL). These systems avoid the use color marks, or gloves, using instead, low-pass and high-pass filters in space and frequency domains, and color space transformations. First system used rotational signatures based on a correlation operator;minimum distance was used for the classification task. Second system computed the seven Hu invariants from binary images;these descriptors fed to a Multi-Layer Perceptron (MLP) in order to recognize the 9 different classes. First system achieves 100% of recognition rate with leaving-one-out validation and second experiment performs 96.7% of recognition rate with Hu moments and 100% using 36 normalized moments and k-fold cross validation.
文摘The hydrocarbon deposits have stimulated worldwide efforts to understand gas production from hydrate dissociation in hydrate reservoirs well. This paper deals with the potential of gas hydrates as a source of energy which is widely available in permafrost and oceanic sediments. It discusses methods for gas production from natural gas hydrates. Authors provide a detailed methodology used to model gas productivity recovery from hydrate reservoir well. The mathematical modelling of gas dissociation from hydrate reservoir as a tool for evaluating the potential of gas hydrates for natural gas production. The simulation results show that the process of natural gas production in a hydrate reservoir is a sensitive function of reservoir temperature and hydrate zone permeability. The model couples nth order decomposition kinetics with gas flow through porous media. The models provide a simple and useful tool for hydrate reservoir analysis.
文摘A computer simulation of the blood flow in a patient specific atherosclerotic right coronary artery is carried out to study the blood flow pattern and the wall shear stress (WSS) distribution in the artery. Both temporal and special distribution patterns of the WSS of the non-Newtonian blood flow are presented and the regions on the lumen surface where the WSS is constantly lower than 1N/m2are identified.
文摘Automatic segmentation of liver in medical images is challenging on the aspects of accuracy, automation and robustness. A crucial stage of the liver segmentation is the selection of the image features for the segmentation. This paper presents an accurate liver segmentation algorithm. The approach starts with a texture analysis which results in an optimal set of texture features including high order statistical texture features and anatomical structural features. Then, it creates liver distribution image by classifying the original image pixelwisely using support vector machines. Lastly, it uses a group of morphological operations to locate the liver organ accurately in the image. The novelty of the approach is resided in the fact that the features are so selected that both local and global texture distributions are considered, which is important in liver organ segmentation where neighbouring tissues and organs have similar greyscale distributions. Experiment results of liver segmentation on CT images using the proposed method are presented with performance validation and discussion.
文摘Laparoscopic surgery is a new abdominal surgical procedure which helps the patients in many ways like less hospital stay, faster recovery and reduced pain. The main disadvantage in this surgical procedure is the reduced haptic perception by the surgeons due to the usage of laparoscopic instrument to handle tissues which in turn cause damage of it as compared to an open surgery. The primary aim of this investigation was to compare the pinch force applied during two different methods of laparoscopic grasping: Finger and Palm grasp. A low cost force sensing resistor tailor made for the grasper tip was designed and fabricated for quantifying the grasper tip force in the study. The results indicate more pinch force was applied during palm grasp as compared to finger grasp so as to prevent the slippage of the tissues from the jaws of the laparoscopic graspers.
文摘Recently, research strives to apply Ultra High Performance Concrete (UHPC) to large-sized structures owing to its remarkable mechanical performance and durability compared to normal concrete. The Korea Institute of Construction Technology proposed SuperBridge800, an edge girder type UHPC cable stayed bridge with central span of 800 m, through its detailed design. The bridge is designed to be erected through the connection of precast UHPC segments. The precast UHPC segment is monolithically composed of one ribbed deck slab and edge girders at each side. The connection between the precast segments is achieved by steel bars at the edge girders and by UHPC cast-in-place wet joint at the slab. Despite of the outstanding mechanical performance of UHPC, the fabrication of large-sized members is a difficult task since UHPC hardens faster than normal concrete and requires a special curing process. Therefore, the constructability of large-sized UHPC segment should be secured to achieve SuperBridge800. Besides, the performance of the connection between segments should also be guaranteed, especially in terms of the fatigue performance of the UHPC cast-in-place joint, which constitutes a weak point. To that goal, two half-scaled UHPC segments are manufactured and the constructability is examined by fabricating a large-sized UHPC member connected with respect to the design conditions. This study conducts rolling fatigue test on the so-fabricated large-sized UHPC member. Rolling fatigue test is carried out up to 2 million cycles considering actual vehicle load at each center and quarter points of the member. The test results confirm that the service limit state is satisfied.
文摘In this study, polymorphisms of the DGAT1 andSTAT5A genes were detected in 528 individuals from Xinong Saanen and Guanzhong goat breeds by PCR-RFLP, PCR-SSCP and DNA sequencing methods. Three allelic variants were identified: DQ380250: g.407_408insC, AJ237937: g.6798C>T and g.6852C>T in both breeds. At g.407_408insC locus, the frequencies of C1 allele were 0.79–0.85, and frequencies of C2 allele were 0.21–0.15. At g.6852C>T locus, frequencies of C3 allele were 0.70–0.72, and frequencies of T3 allele were 0.30–0.28. Compared with goats with C1C1 and C3C3, those with C1C2 and C3T3 genotypes had significant effects on milk yield and fat percentage (P<0.05), respectively. The result showed that does with C1C1C3T3 and C1C2C3T3 had higher milk yield than those with C1C2C3C3 (P < 0.05). In addition, the combined effect of C1C2C3C3 on milk fat percentage was the highest in comparison with other combination genotypes (P<0.05).
文摘Nine strains of ammonia nitrogen degradation strains from C1 to C9 were isolated from industrial wastewater to study their degradation and conversion of ammonia nitrogen. The results showed that C2 strain with a high degradation activiity of ammonia nitrogen, and the ammonia nitrogen degradation rate of the activated C2 strain was 93% within 24 h when the initial concentration of ammonia nitrogen was 200 mg/L under the conditions of inoculation 10%, temperature 35?C, pH 7.0, rotation 200 r/min. And C2 was identified as Bacillus amyloliquefaciens.
文摘A solution containing Cr(VI), Cr(NO3)3 and its complex with an organic acid as well as several commercial solutions containing Cr(III) complexes with an organic acid and additionally CO2+, F-, SO42- ions were used for the studies. Results of the studies obtained in the following commercial solutions: Likonda 2AT, Cr(NO3)3 + malonic acid;Likonda 3Cr5 and Likonda 3CrMC are discussed. Steel coated with chromated Zn coatings was contaminated by some microscopic fungi. The variety of fungi on chromated plates diminished, however the propagules of fungi did not disappear completely. The Likonda 3Cr5 solution diminishes fungi contamination on chromated steel most effectively. In water used to rinse the surface of chromated plates the number of fungi propagules was detected to be higher as compared to that on the plate surface. The least quantity of fungi propagules was detected in water used to rinse plates coated in the Likonda 3Cr5 solution. The main part of fungi detected on chromated plates treated in the Likonda 3Cr5 solution were the fungi of Cladosporium species (C.herbarum, C.cladosporioides). The latter species also dominated on chromated plates coated with zinc and treated with the other solution. It should be mentioned, that on these plates chromated in this solution, Actinomycetes of the Streptomyces group were abundant. After comparison of surfaces of the plates treated in four solutions it has been determined that the surface of the plates treated in the Likonda 3Cr5 passivation solution and exposed to modelling conditions changed least of all. It has been noticed that on the subject studied white porous rust accumulates, the intensity of this process on the surface studied determines both the probability of corrosion and the resistance of the used safety means to the external factors.
文摘In this paper, we investigate the stator wake variability along the axial direction under different rotating speeds and mass flow conditions, in the terms of wake-core position, wake depth, wake width and wake velocity gradient. Experimental study is carried out in a single stage axial compressor by using Hot-wire Anemometer (HWA). Simultaneously, the numerical calculation is brought out in the same experiment rig. Firstly, we analyze the time-averaged velocity and radial vorticity at different axial positions, and explore the wake variability along the axial direction. Then, we present the effects of operation conditions on the wake-core position, and find out the inlet Mach number and incident angle are both the key influence factors of the wake-core position. Finally, we summarize four preliminary conclusions of the wake variability.
文摘The present study considers a finite element analysis of elastic-plastic axi-symmetric hemispherical contact for a frictionless deformable sphere pressed by a rigid flat. The material of the sphere is modeled as elastic perfectly plastic. Analysis is carried out to study the effect of varying modulus of elasticity and sphere radius in wide range of dimensionless interference until the inception of plasticity as well as in plastic range. Results are compared with previous elastic-plastic models. It is found that materials with Young’s modulus to yield strength (E/Y) ratio less than and greater than 300 show strikingly different contact phenomena. The dependency of E on dimensionless interference at which the plastic region fully covers the surface is observed. However with different radius, finite element study exhibits similar elastic-plastic phenomena.
